(R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters PRODUCT OVERVIEW The low-cost ADS-943 is a 14-bit, 3MHz sampling A/D converter optimized to meet the demanding dynamic-range and sampling-rate requirements of contemporary digital telecommunications applications. The ADS-943's outstanding dynamic performance is evidenced by a peak harmonic specification of -83dB and a signal-to-noise ratio (SNR) of 79dB. Additionally, the ADS-943 easily achieves the 2.2MHz minimum sampling rate required by digital receivers in certain ADSL, HDSL and ATM applications. The ADS-943 also addresses size and power constraints normally associated with these types of applications. This device requires just 5V supplies, dissipates 1.7 Watts, and is packaged in a very small 24-pin DDIP. Although optimized for frequency-domain applications, the ADS-943's DNL and noise specifications are also outstanding, thereby making it an equally impressive device for time-domain applications (graphic and medical imaging, process control, etc.). In fact, the ADS-943 guarantees no missing codes to the 14-bit level over the full HI-REL operating temperature range. The functionally complete ADS-943 contains a fast-settling sample-hold amplifier, a subranging (two-pass) A/D converter, an internal reference, timing/control logic, and error-correction circuitry. FEATURES 14-bit resolution 3MHz minimum sampling rate Ideal for both frequency and time-domain applications Excellent peak harmonics, -83dB Excellent signal-to-noise ratio, 79dB No missing codes over full HI-REL temperature range 5V supplies, 1.7 Watts Small, 24-pin ceramic DDIP or SMT Low cost Digital input and output levels are TTL. The unit is edge-triggered, requiring only the rising edge of a start convert pulse to initiate a conversion. The device is offered with a bipolar input range of 2V. Models are available for use in either commercial (0 to +70C) or HI-REL (-55 to +125C) operating temperature ranges. A proprietary, auto-calibrating, error-correcting circuit allows the device to achieve specified performance over the full HI-REL temperature range. PIN INPUT/OUTPUT CONNECTIONS FUNCTION PIN FUNCTION 1 BIT1 (MSB) 24 ANALOG GROUND 2 BIT 2 23 OFFSET ADJUST 3 BIT 3 22 +5V ANALOG SUPPLY 4 BIT 4 21 ANALOG INPUT 5 BIT 5 20 -5V SUPPLY 6 BIT 6 19 ANALOG GROUND 7 BIT 7 18 START CONVERT 8 BIT 8 17 EOC 9 BIT 9 16 BIT 14 (LSB) 10 BIT 10 15 BIT 13 11 BIT 11 14 DIGITAL GROUND 12 BIT 12 13 +5V DIGITAL SUPPLY BLOCK DIAGRAM OFFSET ADJUST 23 BUFFER 16 BIT 14 (LSB) FLASH ADC 1 + 15 BIT 13 12 BIT 12 POWER AND GROUNDING REF 22 +5V DIGITAL SUPPLY 13 DIGITAL GROUND 14 -5V SUPPLY 20 ANALOG GROUND DAC 3 19, 24 AMP START CONVERT 18 EOC 17 FLASH ADC 2 REGISTER +5V ANALOG SUPPLY 11 BIT 11 10 BIT 10 OUTPUT REGISTER S/H DIGITAL CORRECTION LOGIC - REGISTER ANALOG INPUT 21 9 BIT 9 8 BIT 8 7 BIT 7 6 BIT 6 5 BIT 5 4 BIT 4 3 BIT 3 2 BIT 2 1 BIT 1 (MSB) TIMING AND CONTROL LOGIC Figure 1. ADS-943 Functional Block Diagram DATEL * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 1 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS +12V/+15V Supply (Pin 22) 0 to +16 -12V/-15V Supply (Pin 24) 0 to -16 +5V Supply (Pin 13) 0 to +6 Digital Input (Pin 16) -0.3 to +VDD +0.3 Analog Input (Pin 20) 15 Lead Temperature (10 seconds) +300 UNITS Volts Volts Volts Volts Volts C PARAMETERS Operating Temp. Range, Case ADS-943MC, GC ADS-943MM, GM Thermal Impedance Tjc Tca Storage Temperature Range Package Type Weight PHYSICAL/ENVIRONMENTAL MIN. TYP. 0 -55 -- -- MAX. UNITS +70 +125 C C -- 6 -- C/Watt -- 24 -- C/Watt -65 -- +150 C 24-pin, metal-sealed, ceramic DDIP or SMT 0.42 ounces (12 grams) FUNCTIONAL SPECIFICATIONS (TA = +25C, +VDD = +5V, 3MHz sampling rate, and a minimum 3 minute warmup unless otherwise specified.) ANALOG INPUT Input Voltage Range d Input Resistance Input Capacitance DIGITAL INPUT Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Start Convert Positive Pulse Width STATIC PERFORMANCE Resolution Integral Nonlinearity (fin = 10kHz) Differential Nonlinearity (fin = 10kHz) Full Scale Absolute Accuracy Bipolar Zero Error (Tech Note 2) Gain Error (Tech Note 2) No Missing Codes (fin = 10kHz) No Missing Codes (fin = 10kHz) DYNAMIC PERFORMANCE Peak Harmonics (-0.5dB) dc to 500kHz 500kHz to 1MHz 1MHz to 1.5MHz Total Harmonic Distortion (-0.5dB) dc to 500kHz 500kHz to 1MHz 1MHz to 1.5MHz Signal-to-Noise Ratio (w/o distortion, -0.5dB) dc to 500kHz 500kHz to 1MHz 1MHz to 1.5MHz Signal-to-Noise Ratio f (& distortion, -0.5dB) dc to 500kHz 500kHz to 1MHz 1MHz to 1.5MHz Noise Two-Tone Intermodulation Distortion (fin = 975kHz, 1.2MHz, fs = 3MHz, -0.5dB) Input Bandwidth (-3dB) Small Signal (-20dB input) Large Signal (-0dB input) Feedthrough Rejection (fin = 1.5MHz) Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time ( to 0.003%FSR, 4V step) Overvoltage Recovery Time A/D Conversion Rate DATEL MIN. -- -- -- +25C TYP. 2 280 6 MAX. -- -- 15 MIN. -- -- -- 0 TO +70C TYP. 2 280 6 MAX. -- -- 15 MIN. -- -- -- -55 TO +125C TYP. 2 280 6 MAX. -- -- 15 UNITS Volts : pF +2.0 -- -- -- 10 -- -- -- -- 20 -- +0.8 +20 -20 -- +2.0 -- -- -- 10 -- -- -- -- 20 -- +0.8 +20 -20 -- +2.0 -- -- -- 10 -- -- -- -- 20 -- +0.8 +20 -20 -- Volts Volts A A -- -- -0.95 -- -- -- 14 14 14 0.75 0.5 0.15 0.1 0.2 -- -- -- -- +1.25 0.4 0.3 0.5 -- -- -- -- -0.95 -- -- -- 14 14 14 0.75 0.5 0.15 0.1 0.2 -- -- -- -- +1.25 0.4 0.3 0.5 -- -- -- -- -0.95 -- -- -- 14 14 14 1 0.75 0.4 0.3 0.4 -- -- -- -- +1.5 0.6 0.6 1.25 -- -- Bits LSB LSB %FSR %FSR % Bits Bits -- -- -- -83 -83 -83 -77 -77 -77 -- -- -- -83 -83 -83 -77 -77 -77 -- -- -- -81 -81 -81 -75 -75 -75 dB dB dB -- -- -- -80 -80 -80 -76 -76 -76 -- -- -- -80 -80 -80 -76 -76 -76 -- -- -- -78 -77 -77 -74 -73 -73 dB dB dB 76 76 75 79 79 78 -- -- -- 76 76 75 79 79 78 -- -- -- 75 74 74 78 77 77 -- -- -- dB dB dB 73 73 73 -- 77 77 77 125 -- -- -- -- 73 73 73 -- 77 77 77 125 -- -- -- -- 71 71 71 -- 75 75 74 125 -- -- -- -- dB dB dB Vrms -- -82 -- -- -82 -- -- -82 -- dB -- -- -- -- -- -- -- -- 3 30 10 85 400 +5 2 208 100 -- -- -- -- -- -- -- 215 333 -- -- -- -- -- -- -- -- -- 3 30 10 85 400 +5 2 208 100 -- -- -- -- -- -- -- 215 333 -- -- -- -- -- -- -- -- -- 3 30 10 85 400 +5 2 208 100 -- -- -- -- -- -- -- 215 333 -- MHz MHz dB V/s ns ps rms ns ns MHz * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 2 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters DIGITAL OUTPUTS Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Output Coding POWER REQUIREMENTS Power Supply Ranges +5V Supply -5V Supply Power Supply Currents +5V Supply -5V Supply Power Dissipation Power Supply Rejection MIN. +25C TYP. MAX. MIN. 0 TO +70C TYP. MAX. MIN. -55 TO +125C TYP. MAX. UNITS +2.4 -- -- -- -- -- -- -- -- +0.4 -4 +4 +2.4 -- -- -- -- -- -- +0.4 -- -4 -- +4 Offset Binary +2.4 -- -- -- -- -- -- -- -- +0.4 -4 +4 Volts Volts mA mA +4.75 -4.75 +5.0 -5.0 +5.25 -5.25 +4.75 -4.75 +5.0 -5.0 +5.25 -5.25 +4.9 -4.9 +5.0 -5.0 +5.25 -5.25 Volts Volts -- -- -- -- +210 -180 1.7 -- +230 -195 2.0 0.05 -- -- -- -- +210 -180 1.7 -- +230 -195 2.0 0.05 -- -- -- -- +210 -180 1.7 -- +230 -195 2.0 0.05 mA mA Watts %FSR/%V Effective bits is equal to: Footnotes: All power supplies must be on before applying a start convert pulse. All supplies and the clock (START CONVERT) must be present during warmup periods. The device must be continuously converting during this time. Contact DATEL for availability of other input voltage ranges. A 3MHz clock with a 20nsec positive pulse width is used for all production testing. When sampling at 3MHz, the start convert pulse must be between 10 and 110nsec wide or between 160 and 300nsec wide. The falling edge must not occur between 110 and 160nsec. For lower sampling rates, wider start pulses may be used. (SNR + Distortion) - 1.76 + Full Scale Amplitude Actual Input Amplitude 20 log 6.02 This is the time required before the A/D output data is valid after the analog input is back within the specified range. This time is only guaranteed if the input does not exceed 2.2V (S/H Saturation Voltage). The minimum supply voltages of +4.9V and -4.9V for VDD are required for -55C operation only. The minumum limits are +4.75V and -4.75V when operating at +125C. TECHNICAL NOTES 1. Obtaining fully specified performance from the ADS-943 requires careful attention to pc-card layout and power supply decoupling. The device's analog and digital ground systems are connected to each other internally. For optimal performance, tie all ground pins (14, 19 and 24) directly to a large analog ground plane beneath the package. Bypass all power supplies to ground with 4.7F tantalum capacitors in parallel with 0.1F ceramic capacitors. Locate the bypass capacitors as close to the unit as possible. 2. The ADS-943 achieves its specified accuracies without the need for external calibration. If required, the device's small initial offset and gain errors can be reduced to zero using the adjustment circuitry shown in Figures 2 and 3. When using this circuitry, or any similar offset and gain-calibration hardware, make adjustments following warmup. To avoid interaction, always adjust offset before gain. 3. Applying a start convert pulse while a conversion is in progress (EOC = logic "1") will initiate a new and inaccurate conversion cycle. Data for the interrupted and subsequent conversions will be invalid. 4. A passive bandpass filter is used at the input of the A/D for all production testing. 2k 7 GAIN ADJUST +5V SIGNAL INPUT 1.98k7 To Pin21 of ADS-943 507 -5V Figure 2. Optional ADS-943 Gain Adjust Calibration Circuit DATEL * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 3 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters Gain Adjust Procedure CALIBRATION PROCEDURE 1. Apply +1.99963V to the ANALOG INPUT (pin 21). Any offset and/or gain calibration procedures should not be implemented until devices are fully warmed up. To avoid interaction, offset must be adjusted before gain. The ranges of adjustment for the circuits in Figures 2 and 3 are guaranteed to compensate for the ADS-943's initial accuracy errors and may not be able to compensate for additional system errors. 2. Adjust the gain potentiometer until all output bits are 1's and the LSB flickers between 1 and 0. 3. To confirm proper operation of the device, vary the input signal to obtain the output coding listed in Table 2. A/D converters are calibrated by positioning their digital outputs exactly on the transition point between two adjacent digital output codes. This can be accomplished by connecting LED's to the digital outputs and adjusting until certain LED's "flicker" equally between on and off. Other approaches employ digital comparators or microcontrollers to detect when the outputs change from one code to the next. Table 1. Gain and Zero Adjust INPUT VOLTAGE RANGE ZERO ADJUST +1/2 LSB GAIN ADJUST +FS -11/2 LSB 2V +122V +1.99963V Offset adjusting for the ADS-943 is normally accomplished at the point where the MSB is a 1 and all other output bits are 0's and the LSB just changes from a 0 to a 1. This digital output transition ideally occurs when the applied analog input is +1/2 LSB (+122V). Table 2. Output Coding for Bipolar Operation Gain adjusting is accomplished when all bits are 1's and the LSB just changes from a 1 to a 0. This transition ideally occurs when the analog input is at +full scale minus 11/2 LSB's (+1.99963V). OFFSET BINARY BIPOLAR SCALE INPUT VOLTAGE (2V RANGE) +FS - 1 LSB +1.99976 11 1111 1111 1111 +3/4FS +1.50000 11 1000 0000 0000 +1/2FS +1.00000 11 0000 0000 0000 Zero/Offset Adjust Procedure MSB LSB 1. Apply a train of pulses to the START CONVERT input (pin 18) so the converter is continuously converting. 0 0.00000 10 0000 0000 0000 -1/2 FS -1.00000 01 0000 0000 0000 2. Apply +122V to the ANALOG INPUT (pin 21). -3/4 FS -1.50000 00 1000 0000 0000 -FS +1 LSB 1.99976 00 0000 0000 0001 -FS -2.00000 00 0000 0000 0000 3. Adjust the offset potentiometer until the output bits are 10 0000 0000 0000 and the LSB flickers between 0 and 1. +5V ~ -5V 19 ANALOG INPUT 4.7F + 4.7F 4.7F + + 0.1F 0.1F 20 24 0.1F 22, 13 14 21 +5V ZERO/ OFFSET ADJUST 23 ADS-943 20k7 -5V START CONVERT 18 1 2 3 4 5 6 7 8 9 10 11 12 15 16 17 BIT 1 (MSB) BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT 10 BIT 11 BIT 12 BIT 13 BIT 14 (LSB) EOC ~ A single +5V supply should be used for both the +5V analog and +5V digital. If separate supplies are used, the difference between the two cannot exceed 100mV. Figure 3. Connection Diagram DATEL * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 4 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters THERMAL REQUIREMENTS devices do not overheat. The ground and power planes beneath the package, as well as all pcb signal runs to and from the device, should be as heavy as possible to help conduct heat away from the package. All DATEL sampling A/D converters are fully characterized and specified over operating temperature (case) ranges of 0 to +70C and -55 to +125C. All room-temperature (TA = +25C) production testing is performed without the use of heat sinks or forced-air cooling. Thermal impedance figures for each device are listed in their respective specification tables. Electrically-insulating, thermally-conductive "pads" may be installed underneath the package. Devices should be soldered to boards rather than "socketed," and of course, minimal air flow over the surface can greatly help reduce the package temperature. These devices do not normally require heat sinks; however, standard precautionary design and layout procedures should be used to ensure N+1 N START CONVERT 20ns typ. 333nsec 10ns typ. Acquisition Time 125ns typ. INTERNAL S/H 208ns typ. 215ns max. Hold 35ns typ. 130ns EOC 125ns typ. Conversion Time 120ns min., 130ns typ., 140ns max. 30ns typ. Invalid Data 10ns max. OUTPUT DATA Data N-1 Valid Data N Valid Data N+1 Valid 283ns typ. 50ns typ. Note: 1. Scale is approximately 20ns per division. Sampling rate = 3MHz. 2. The start convert positive pulse width must be between either 10 and 110nsec or 160 and 300nsec (when sampling at 3MHz) to ensure proper operation. For sampling rates lower than 3MHz, the start pulse can be wider than 300nsec, however a minimum pulse width low of 30nsec should be maintained. A 3MHz clock with a 20nsec positive pulse width is used for all production testing. Figure 4. ADS-943 Timing Diagram DATEL * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 5 of 8 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * ANA. IN Tel: (508) 339-3000 * SG10 SG3 SG2 SG1 P4 P2 26 24 22 20 18 16 14 12 10 8 6 4 2 25 23 21 19 17 15 13 11 9 7 5 3 1 ANA. IN 20H L7 20H L6 20H L5 20H L4 20H L3 20H L2 20H L1 + + + C8 0.01F C9 0.01F 2.2F C2 2.2F +5VF C11 C4 C12 0.01F C5 2.2F 0.01F 0.01F 2.2F 2.2F C10 C3 2.2F 0.01F C14 0.01F 2.2F C7 C13 C6 R2 SG5 +5VA +15V -15V -5VA +5V 5 +15V 10 12 11 13 -15V SG8 0.1F (Optional) U6 HCT7474 01 Apr 2011 5 4 13 12 11 U5 6 7 8 HCT7474 7 ADS-943 AGND BIT1 1 OFFSET BIT2 2 +5VA BIT3 3 AIN BIT4 4 -5V BIT5 5 AGND BIT6 6 TRIG BIT7 7 EOC BIT8 8 BIT14 BIT9 9 BIT13 BIT10 10 DGND BIT11 11 +5VD BIT12 12 U1 3.2k 2.2F 14 4 PR 5 2 D U6 Q 6 3 CK Q 1 R3 CLR 0.1F C24 + C23 START CONVERT 24 23 22 21 20 19 18 17 16 15 14 13 +5V 15pF C25 +5VA -5V X1 14 SG9 +5VF 2.2F C27 74HCT86 0.1F C15 7 GND U5 14 +5VF ANA. IN SG4 0.1F C26 3MHz CRYSTAL +5VF 2 3 JPR1 10 9 1 P3 U5 U5 + 0.1F 2.2F C16 C22 3 2 3 4 5 6 7 8 9 11 2 3 4 5 6 7 8 9 11 74HCT573 C21 74HCT573 19 18 17 16 15 14 13 12 1 +5VF 19 18 17 16 15 14 13 12 1 2.2F Q1 1D 2D Q2 Q3 3D 4D Q4 U2 Q5 5D 6D Q6 Q7 7D Q8 8D OE CE 10 20 10 C17 0.1F Q1 1D 2D Q2 Q3 3D 4D Q4 5D U3 Q5 6D Q6 Q7 7D Q8 8D OE CE 20 + +5VF 3. SEE DATEL DWG A-24546 FOR ADDITIONAL INFORMATION ON ADS-B946 EVALUATION BOARD. 2. CLOSE SG1-SG3, SG9, SG10. C1 - C7 ARE 20V. ALL RESISTORS ARE IN OHMS. 1. UNLESS OTHERWISE SPECIFIED ALL CAPACITORS ARE 50V. NOTES: 74HCT86 8 74HCT86 2 1 START CONV. 2 3 JPR2 1 CE B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 TRIG 2 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 P1 1 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 (R) www.datel.com Figure 5. ADS-943 Evaluation Board Schematic 9 Q 8 SPARE GATES 0.1F C19 (Optional) -15V C20 PR D CK CLR 2 R1 C18 0.1F (Optional) SG6 20k CLC402 HI2541 10 +5VA OFFSET ADJUST -5VA SG7 6 U4 11 +15V +5VF + (Optional) 4 - -5V OPTION C1 + + + * + DATEL + (R) ADS-943 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters * e-mail: help@datel.com MDA_ADS-943.B03 Page 6 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters 0 Amplitude Relative to Full Scale (dB) -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 0 150 kHz 300 kHz 450 kHz 600 kHz 750 kHz 900 kHz 1.05 MHz 1.20 MHz 1.35 MHz 1.5 MHz Frequency (fs = 3MHz, fin = 1.485MHz, Vin = -0.5dB, 16,384-point FFT) Figure 6. ADS-943 FFT Analysis +0.60 DNL (LSB's) 0.00 Number of Occurences -0.58 0 16,384 Digital Output Code 0 16,384 Digital Output Code Figure 7. ADS-943 Histogram and Differential Nonlinearity DATEL * 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA * Tel: (508) 339-3000 * www.datel.com 01 Apr 2011 * e-mail: help@datel.com MDA_ADS-943.B03 Page 7 of 8 (R) ADS-943 (R) 14-Bit, 3MHz, Low-Distortion, Sampling A/D Converters MECHANICAL DIMENSIONS - INCHES (mm) 1.31 MAX. (33.27) 24-Pin DDIP Versions 24 Dimension Tolerances (unless otherwise indicated): 2 place decimal (.XX) 0.010 (0.254) 3 place decimal (.XXX) 0.005 (0.127) 13 0.80 MAX. (20.32) ADS-943MC ADS-943MM ADS-943/883 1 Lead Material: Kovar alloy Lead Finish: 50 microinches (minimum) gold plating over 100 microinches (nominal) nickel plating 12 0.100 TYP. (2.540) 1.100 (27.940) 0.235 MAX. (5.969) PIN 1 INDEX 0.200 MAX. (5.080) 0.010 (0.254) 0.190 MAX. (4.826) 0.100 (2.540) 0.040 (1.016) 0.018 0.002 (0.457) +0.002 -0.001 0.100 (2.540) 0.600 0.010 (15.240) SEATING PLANE 0.025 (0.635) 1.31 MAX. (33.02) 24-Pin Surface Mount Versions Dimension Tolerances (unless otherwise indicated): 2 place decimal (.XX) 0.010 (0.254) 3 place decimal (.XXX) 0.005 (0.127) 13 24 0.80 MAX. (20.32) ADS-943GC ADS-943GM ADS-943G/883 1 Lead Material: Kovar alloy Lead Finish: 50 microinches (minimum) gold plating over 100 microinches (nominal) nickel plating 12 0.020 TYP. (0.508) 0.190 MAX. (4.826) 0.060 TYP. (1.524) PIN 1 INDEX 0.100 (2.540) 0.100 TYP. (2.540) 0.015 (0.381) MAX. radius for any pin 0.130 TYP. (3.302) 0.020 (0.508) 0.010 TYP. (0.254) 0.040 (1.016) ORDERING INFORMATION MODEL NUMBER OPERATING TEMP. RANGE 24-PIN PACKAGE ACCESSORIES ADS-943MC 0 to +70C DDIP ADS-B943 Evaluation Board (without ADS-943) ADS-943MC-C* 0 to +70C DDIP HS-24 Heat Sinks for all ADS-943 DDIP models. ADS-943MM -55 to +125C DDIP ADS-943/883 -55 to +125C DDIP ADS-943GC 0 to +70C SMT ADS-943GC-C* 0 to +70C SMT ADS-943GM -55 to +125C SMT ADS-943G/883 -55 to +125C SMT Receptacles for PC board mounting can be ordered through AMP Inc. Part #3-331272-8 (Component Lead Socket), 24 required. For MIL-STD-883 product specifications, contact DATEL. *RoHS-6 hazardous substance compliant. Product models without the "-C" suffix are not RoHS compliant. RoHS-6 fabrication does not claim EU RoHS exemption 7b - lead in solder. DATEL 11 Cabot Boulevard, Mansfield, MA 02048-1151 USA . makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. ITAR and ISO 9001/14001 REGISTERED www.datel.com * e-mail: help@datel.com 01 Apr 2011 MDA_ADS-943.B03 Page 8 of 8