F-51167NCU-FW-AA - Optrex America, Inc.

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 1/17

OPTREX

LCD Module Specification

Ｆ－５１１６７ＮＣＵ－ＦＷ－ＡＡ

Ｆ－５１１６７ＮＣＵ－ＦＷ－ＡＡＦ－５１１６７ＮＣＵ－ＦＷ－ＡＡ

Ｆ－５１１６７ＮＣＵ－ＦＷ－ＡＡ

Table of Cont ent s

1. General Specifications ............................................................................ 2

2. Electrical Specifications.......................................................................... 3

3. Optical Specifications............................................................................. 8

4. I/O Terminal.......................................................................................... 10

5. Test......................................................................................................... 12

6. Appearance Standards........................................................................... 13

7. Code System of Production Lot......................................................... 15

8. Type Number ........................................................................................ 15

9. Applying Precautions............................................................................ 15

10. Precautions Relating Product Handling .............................................. 16

11. Warranty................................................................................................. 17

Type No.

********

Aug 9, 2000

First Edition

Final Revisi on

Quality A ssurance Div.

Product i on Di v.

Checked by

Approved by

Product i on Di v.

Design Engi neeri ng Di v.

Prepared by

Revision History

Rev. Date Page Comment

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 2/17

OPTREX

1.General Specifications

Operating Temp. ： min. 0℃ ～ max. 50℃

Storage Temp. ： min. -20℃ ～ max. 70℃

Dot Pixels ： 320×3 [R.G.B] (W) × 240 (H) dots

Dot Size ： 0.10 (W) × 0.34 (H) mm

Dot Pitch ： 0.12 (W) × 0.36 (H) mm

Viewing Area ： 122.0 (W) × 92.0 (H) mm

Outline Dimensions ： 167.1* (W) × 109.0 (H) × 8.0 max. (D) mm

* Without CFL Cable

Weight ： 204g max.

LCD Type ： CTD-17753

( F-STN / Color-mode / Transmissive )

Viewing Angle ： 12:00

Data Transfer ： 8-bit pa rallel data transfer

Duty ： 1/240

Backlight ： Cold Cathode Fluorescent Lamp (CFL) × 1

Drawings ： Dimensional Outline UE-300830

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 3/17

OPTREX

2.Electrical Specifications

2.1.Absolute Maximum Ratings VSS=0V

Parameter Symbol Conditions Min. Max. Units

Supply Voltage

(Logic)

VCC1-VSS － -0.3 7.0 V

Supply Voltage

(LCD Drive)

VCC2-VSS － 0 6.0 V

Input Voltage VI － -0.3 VCC1+0.3 V

VADJ

Input Voltage

VADJ-VSS － 0 3.0 V

2.2.DC Characteristics Ta=25℃, VSS=0V

Parameter Symbol Conditions Min. Typ. Max. Units

Supply Voltage

(Logic)

VCC1-VSS － 3.0

－ 5.5 V

Supply Voltage

(LCD Drive)

VCC2-VSS － 3.0

－ 5.5 V

Voltage for Contrast

Adjustment (Note1)

VADJ-VSS － 0.8

－ 2.7 V

High Level

Input Voltage

VIH V

CC1=3.0～5.5V 0.8× V

CC1 － V

CC1 V

Low Level

Input Voltage

VIL V

CC1=3.0～5.5V 0 － 0.2× V

CC1 V

Supply Current

IVCC1 V

CC1-VSS=5.0V － 20.0 40.0 mA

(Note2) IVCC2 V

CC2-VSS=5.0V － 40.0 60.0 mA

Clock Frequency fCP V

CC1=3.0～5.5V

Duty=50%

－－ 30 MHz

Note1:T he relation between Voltage for Contrast Adjustment and LCD Contrast is shown as follows;

0.8V(Bright)～2.7V(dark)

Note2:Supply current which checker pattern displayed.

GBR

fF=70Hz

VOD=26.6

GBRGBRGBR

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 4/17

OPTREX

2.3. AC Characteristics VCC1=3.0～5.5V

Parameter Symbol Min. Max. Units

LP Cycle Time tLP － 5

－ ns

LP High Level Width tWLH － 40

－ ns

LP Low Level Width tWLL － 1000

－ ns

Rise/Fall Time tr, td Note 1 － 6.6 ns

FLM Setup Time tst － 60

－ ns

FLM Hold Time thd － 30

－ ns

CP Cycle Time tCP － 40

－ ns

CP High Level Width tWCH － 15

－ ns

CP Low Level Width tWCL － 15

－ ns

LP Setup Time 1 tst1 － 30

－ ns

LP Setup Time 2 tst2 － 30

－ ns

LP H old Time thd1 － 15

－ ns

Data Setup Time tst3 － 15

－ ns

Data Hold Time thd2 － 15

－ ns

LP ↑ to CP ↑ tLH － 25

－ ns

LP ↓ to CP ↓ tLS － 25

－ ns

DISPOFF Low Level Width tWDL － 100

－ ns

DISPOFF Cancellation Time tSD － 20

－ ns

Note 1:The rise and fall times (tr, tf ) must satisfy the following relationships.

tr, tf≦（１／ｆ－２×tW）／２ｆ：frequency t

W：Mini mum palse width

tWLH

ＬＰ

ＣＰ

ＦＬＭ

VIH=0.7×VCC1

VIL=0.3×VCC1

VIH

ＶIL

ＶIH

ＶIL

ＶIH

VIL

VIH

Ｄ０～Ｄ７ LAST DATA TOP DATA

thd

tST

tWLL

tLP

tst2 tst1

tWCH tCP

tWCL

thd1

thd2

tst3

tLS

tLH

ＤＩＳＰＯＦＦ

tWDL tSD

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 5/17

OPTREX

2.4.Timing Chart

2.5.Comparison of Display and Data

T=0.0595ms typ.

240×T

FLM

(Reduction)

FLM

～#1 DATA

SEGSEG SEGSEG SEGSEG SEGSEG

960952 168 960952 168

953～

945～ 9～

1～953～

945～ 9～

1～

SEG1 SEG960

#240

D0～D7

D4D5 D0D1

TOP VIEW

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 6/17

OPTREX

2.6.Power Supply ON/OFF Sequence

2.6.1.ON Sequence

2.6.2.OFF Sequence

Please maintain the above sequence when turning on and off the power supply of the module.

If DISPOFF is supplied to the module while internal alternate signal for LCD driving (M) is

unstable, DC component will be supplied to the LCD panel. This may cause damage the LCD

module.

VSS

VCC1

VSS

VCC1

VSS

VCC1,VCC2

DISPOFF

VCC1,VCC2 0≦t

SIGNAL

LEVEL

50 ms≦t

VSS

VCC1

VSS

VCC1

VSS

VCC1,VCC2

DISPOFF

VCC1,VCC2

0≦t

SIGNAL

LEVEL

200 ms≦t

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 7/17

OPTREX

2.7.Lighting Specifications Ta=25℃

Parameter Symbol Conditions Min. Typ. Max. Units Notes

Lamp Voltage VL －－ 430 － Vrms 1

Lamp Current IL － 4.0 5.0 6.0 mArms 2

Starting Vo ltage VS －－－ 700 Vrms 3

Surface Luminance L IL = 5.0 mA 100 120 － cd/㎡ 4

Average Life TAL I

L = 5.0 mA 20000 －－ hrs 5

Note 1 : The voltage ( r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for

3 minutes .

Note 2 : The current ( r.m.s. ) to flow thro ugh the lamp with the electric di scharge. It i s mea sured after

lighting for 3 minutes.

Note 3 : The voltage at starting the electric discharge when the voltage is increased gradually from 0V.

Note 4 : Surface Luminance is specified by the average of 9 luminance values measured at each point

shown above after 20 minutes power on with the all ON pattern adjusted to maximum contrast and

the dimming control of 100%. ( maximum brightness )

Note 5 : CFL life is defined as the time for which the initial luminance is attenuated by 50% of the

luminance value. Average Life representes the time elapsed at the point of time when the residual

ratio becomes below 50% when plural lamps are lighted in comparison with the definition of life

mentioned above.

CFL Testin

Circuit

VS VL

Measurement Points

X=120

X=60

X=180

Y=260Y=160Y=60

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 8/17

OPTREX

3.Optical Specifications

3.1.Optical Characteristics Ta=25℃, 1/240 Duty,1/16.2 Bias, VOD=26.6V, θ= 0 ﾟ, φ=－ﾟ

Parameter Symbol Conditions Min. Typ. Max. Units

Contrast Ratio Note 1 CR θ= 0 ﾟ, φ=－ﾟ－ 40 －

Chromaticity (white) x －－ 0.324 －

－－ 0.361 －

Viewing Angle Shown in 3.3

Response Rise

Note 2 TON －－ 400 600 ms

Time Decay Note 3 TOFF －－ 150 230 ms

Note 1 : Contrast ratio is definded as follows.

CR = LON / LOFF

LON : Luminance of the ON segments

LOFF : Luminance of the OFF segments

Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON

signal is applied.

Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF

signal is applied.

Note 4 : Definition of Driving Voltage VOD

Assuming that the typical driving waveforms shown below are applied to the LCD Panel at

1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage VD is definded

as the voltage VO-P when the contrast ratio (CR=LON / LOFF) is at its ma ximum.

VO-P

1 / fF

(

B-2

)

×VO-P / B

1 /

(

fF×A

)

〈OFF SIGNAL〉

〈ON SIGNAL〉

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 9/17

OPTREX

3.2.Defi nition of Viewing Angle and Optimum Viewing Area

･Point ● shows the point where contrast ratio is measured. : θ= 0 ﾟ, φ=－ﾟ

･Driving condition : 1/240 Duty,1/16.2 Bias, VOD= 26.6V, fF=70Hz

･Area shows typ. CR

≧2

3.3.System Block Diagram

0ﾟ

90 ﾟ

180 ﾟ

270 ﾟ

135 ﾟ

315 ﾟ

225 ﾟ

45 ﾟ

180 ﾟ

90 ﾟ

θ(φ= 0 ﾟ）

10 20 30 40 50

Halogen bulb

Computer

Rotation Table (θ,φ)

Temperature Chamber

LCD

Optical Fiber

Waveform Generator

Control Unit &

#1980A WB

Photometer

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 10/17

OPTREX

4.I/O Terminal

4.1.Pin Assignment

CN1

No. Symbol Level Function

1 D0 H / L Display Data

2 D1 H / L Display Data

3 D2 H / L Display Data

4 D3 H / L Display Data

5 D4 H / L Display Data

6 D5 H / L Display Data

7 D6 H / L Display Data

8 D7 H / L Display Data

9 DISP OFF H / L Display Control Signal H : Display on L : Display off

10 FLM H / L First Line Marker

11 LP H→L Data Latch Signal

12 CP H→L Clock Signal for Shifting Data

13 M H / L Alternate Signal for LCD Drive

14 V

CC1 － Power Supply for Logic

15 V

SS ― Power Supply (0V, VSS)

16 V

SS ― Power Supply (0V, VSS)

17 V

CC2 － Power Supply for LCD Drive

18 V

ADJ ― Voltage Leve l for LCD Contrast Adjustment

CN2

No. Symbol Level Function

1 CFL HOT － Power Supply for CFL (HOT)

2 NC － Non-connection

3 NC － Non-connection

4 CFL GND － Power Supply for CFL (GND)

4.2.Example of Power Supply

It is recommended to apply a potentiometer for the contrast adjust due to the tolerance

of the driving voltage and its temperature dependence.

MODULE

VADJ

VSS

VCC2 VCC2

3.3V

R1+R2+VR=10～20KΩ

VSS

VCC1 VCC1

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 11/17

OPTREX

4.3.Block Diagram

CFL GND

CFL HOT

VADJ

VSS

VCC1

FLM

DISPOFF

or equivalent

MN86372 × 2

COM.DRIVER L C D P

240

320×3[RGB]×240dots

TO LSI LOGIC

TO LSI

Bias circuit

ＣＦＬ

or equivalent

MN863830 × 4

SEG.DRIVER

960

D0～D7

VCC2

MM CIRCUIT

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 12/17

OPTREX

5.Test

No change on display and in operation under the following test condition.

No. Parameter Conditions Notes

1 High Temperature Operating 50℃±2℃, 96hrs (operation state)

2 Low Temperature Operating 0℃±2℃, 96hrs (operation state) 3

3 High Temperature Storage 60℃±2℃, 96hrs 4

4 Low Temperature Storage -20℃±2℃, 96hrs 3, 4

5 Damp Proof Test 40℃±2℃, 90～95%RH, 96hrs 3, 4

6 Vibration Test Total fixed amplitude : 1.5mm 5

Vibration Frequency : 10～55Hz

One cycle 60 seconds to 3 directions of X, Y, Z for

each 15 minutes

7 Shock Test To be measured after dropping from 60cm high on

the concrete surface in packing state.

Note 1 : Unless otherwise specified, tests will be conducted under the following condition.

Temperature : 20±5℃

Humidity : 65±5%

Note 2 : Unless otherwise specified, tests will be not conducted under functioning state.

Note 3 : No dew condensation to be observed.

Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity

after removed from the test chamber.

Note 5 : Vib r ation test will be conducted to the product itself without putting it in a container.

GDC

60cm

C o ncrete S urface

Dropping method corner dropping

E,F,G face : once

B,C,D edge : once

A corner : once

Face dropping

Edge drop ping

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 13/17

OPTREX

6.Appearance Standards

6.1.Inspection conditions

The LCD shall be inspected under 40W white fluorescent light.

The distance between the eyes and the sample shall be more than 30cm.

All directions for inspecting the sample should be within 45 ﾟagainst perpendicular line.

6.2.Definition of applicable Zones

A Zone : Active display area

B Zone : Area from outside of "A Zone" to validity viewing area

C Zone : Rest parts

A Zone + B Zone = Validi ty viewing area

A Zone

B Zone

C Zone

Bezel Flame

45ﾟ

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 14/17

OPTREX

6.3.Standards

No. Parameter Criteria

1 Black and (1) Round Shape

White Spots, Zone Acceptable Number

Foreign Sub st ances Dimension ( mm) A B C

D ≦0.1 * * *

0.1

＜ D ≦0.2 3 5 *

0.2

＜ D ≦0.25 2 3 *

0.25＜ D ≦0.3 0 1 *

0.3

＜ D 0 0 *

D = ( Long + Short ) / 2 * : Disregard

(2) Line Shape

Zone Acceptable Number

X (mm) Y (mm) A B C

－ 0.03≧W * * *

2.0≧L 0.05≧W 3 3 *

1.0≧L 0.1

≧W 3 3 *

－ 0.1

＜W In the same way (1)

X : Length Y : Width * : Disregard

Total defects shall not exceed 5.

2 Air Bubbles

(between glass Zone Acceptable Number

& polarizer) Dimensi on (mm) A B C

D ≦ 0.3 * * *

0.3

＜ D ≦ 0.4 3 * *

0.4

＜ D ≦ 0.6 2 3 *

0.6

＜ D 0 0 *

* : Disregard

Total defects shall not exceed 3.

3 The Shape of Dot However, each pixel shall remain more than one-third of the original

pixel size.

4 Polarizer Scratches Not to be conspicuous defects.

5 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not

defective.

6 Complex Foreign Black spots, line shaped foreign substances or air bubbles between

Substance Defects glass & polarizer should be 5pcs maximum in total.

7 Distance between D≦0.2 : 20mm or more

Different Foreign 0.2＜D : 40mm or more

Substance Defects

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 15/17

OPTREX

7.Code System of Production Lot

The production lot of module is specified as follows.

□ □ □ □ □ □

Factory Number (Numeral)

Factory Code (Alphabet)

Production Week (1～5)

Pr oduction Month (1 ～9, X, Y, Z)

Production Year (Lower 2 digits)

8.Type Number

The type number of module is specified on the back of module as follows.

Ｆ－５１１６７ＮＣＵ－ＦＷ－ＡＡ

Label

9.Applying Precautions

Please contact us when questions and/or new problems not specified in this specifications arise.

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 16/17

OPTREX

10. Precautions Relating Product Handling

The Following precautions will guide you in handling our product correctly.

1) Liquid crystal display devices

① The liquid crystal display device panel used in the liquid crystal display module is made of plate

glass. Avoid any strong mechanical shock. Should the glass break handle it with care.

② The polarizer adhering to the surface of the LCD is made of a soft material.

Guard against scratching it.

2) Care of the liquid crystal display module against static electricity discharge.

① When working with the module, be sure to ground your body and any electrical equipment you may

be using. We strongly recommend the use of anti static mats ( made of rubber ), to protect work

tables against the hazards of electrical shock.

② Avoid t he use of work clothing made of syntheti c fibers. We recommend cotton clot hing or othe r

conductivity-treated fibers.

③ Slowly and carefully remove the protective film from the LCD module, since this operation can

generate static electricity.

3) When the LCD module alone must be stored for long periods of time:

① Protect the modules from high temperature and humidity.

② Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.

③ Protect the modules from excessive external forces.

4) Use the module with a power supply that is equipped with an overcurrent protector circuit,

since the module is not provided with this protective feature.

5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands

or clothing come in contact with LCD fluid, wash immediately with soap.

6) Conduc1tivity is not guaranteed for models that use metal holders where solder connections

between the metal holder and the PCB are not used. Please contact us to discuss appropriate

ways to assure conductivity.

7) For models which use CFL:

① High voltage of 1000V or greater is applied to the CFL cable connector area.

Care should be taken not to touch connection areas to avoid burns.

② Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn.

③The use of CFLs for extended periods of time at low temperatures will significantly shorten their

service life.

F-51167NCU-FW-AA (AA) No.2000-0249 OPTREX CORPORATION Page 17/17

OPTREX

8) For mod els which use touch panels:

①Do not stack up modules since they can be damaged by components on neighboring modules.

②Do not place heavy objects on top of the product. This could cause glass breakage.

9) For models which use COG,TAB,or COF:

①The mechanical strength of the product is low since the IC chip faces out unprotected from the rear.

Be sure to protect the rear of the IC chip from external forces.

②Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from electrical

damage, avoid installation configurations in which the rear of the IC chip runs the risk of making

any electrical contact.

10) Models which use flexible cable, heat seal, or TAB:

①In order to maintain reliability, do not touch or hold by the connector area.

②Avoid any bending, pulling, or other excessive force, which can result in broken connections.

11. Warranty

This product has been manufactured to your company’s specifications as a part for use in your company’s

general electronic products. It is guaranteed to perform according to delivery specifications. For any other

use apart from general electronic equipment, we cannot take responsibility if the product is used in medical

devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other

applications in which there is a direct risk to human life and where extremely high levels of reliability are

required. If the product is to be used in any of the above applications, we will need to enter into a separate

product liability agreement.

① We cannot accept responsibility for any defect, which may arise from additional manufacturing of

the product (including disassembly and reassembly), after product delivery.

② We cannot accept responsibility for any defect, which may arise after the application of strong

external force to the product.

③ We cannot accept responsibility for any defect, which may arise due to the application of static

electricity after the product has passed your company’s acceptance inspection procedures.

④ When the product is in CFL models, CFL service life and brightness will vary according to the

performance of the inverter used, leaks, etc. We cannot accept responsibility for product

performance, reliability, or defect, which may arise.

⑤ We cannot accept responsibility for ind ustr ial property, which may arise through the use of your

product, with exception to those issues relating directly to the structure or method of

manufacturing of our product.

⑥ Optrex will not be held responsible for any quality guarantee issue for defect prod ucts judged as

Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex

America, Optrex Europe, Display LC delivery which ever comes later.