PRODUCT SPECIFICATIONS Customer () Model () T170S-5RB004N-0A18R0-200FH Mode () Five-wire Analog Touch Panel Date () May 06, 2008 Version () 6.3 Customer Approval HIGGSTEC INCORPORATED 8 F., No. 609, Wan Shou Rd., Sec. 1, Kweishan, Taoyuan Hsien 33350, Taiwan. TEL886-2-8209-9696 FAX886-2-8200-3030 E-mailinfo@higgstec.com.tw Approve Review Preparation Henry Andy Young TABLE OF CONTENTS 00. Specification Revision Record []................................................ 01 00. Dimension Drawing []........................................................... ........... 02 01. Scope []............................................................................................. 03 02. Features [].......................................................................................... 03 03. General Specification []................................................................... 03 04. Environmental Characteristics []..................................................... 03 05. Optical Characteristics []................................................................ 04 06. Electrical Characteristics []............................................................. 04 07. Mechanical Characteristics [].......................................................... 05 08. Reliability []...................................................................................... 05 09. Durability []............................................................................. ......... 05 10. Inspection Methods []..................................................................... 06 11. Appearance Inspection []................................................................ 07 12. Attention for Mounting Condition [].............................................. 08 13. Warranty []......................................................................................... 09 14. Appendices []..................................................................................... 09 Appearance Specification []....................................................... 11 15. Caution []........................................................................................ 10 Date: May 06, 2008 Version: 6.3 SPECIFICATION REVISION RECORD Customer [] Customer NO. [] NO. Version. [] [] Date []May 06, 2008 Model []T170S-5RB004N-0A18R0-200FH Date Summary of Changes Page [] [] [] Remarks[] Date: May 06, 2008 Version: 6.3 Page: 01/11 01. Scope The specification is for Five-Wire Analog Resistive touch panel. [] [-] 02. Features [] (1) (2) (3) 03. General Specification (1) [] (2) (3) Item [] Type [] Specifications [] Five-Wire Analog Resistive [-] Input Mode [] Cable [] Item [] Frame Size [] View Area [] Active Area [] Total (4) Thickness Stylus or Finger [] FFC Specifications [] 356.000.30 X 286.500.30 mm 343.000.20 X 275.500.20 mm 337.000.20 X 269.500.20 mm 2.200.20 mm [] (5) 04. Environmental Characteristics Tail Length [] 205.006.00 mm Specifications [] Item [] [] Temperature [] Humidity [] (Non Condensing) [] (1) (2) Operation [] Storage [] -10C ~ +70C 20%RH ~ 80%RH -40C ~ +80C 10%RH ~ 85%RH Note: All terms under 1 atmosphere. [: 1 ] Date: May 06, 2008 Version: 6.3 Page: 03/11 05. Optical Characteristics (1) [] (2) 06. Electrical Characteristics [] Item [] Transparency [] Haze [] Specifications [] 80% 3% (Measured by BYK-Gardner ) 8% 3% Item [] Loop (1) Resistance Specifications [] X:20~500, Y:20~500 (See Figure 6-1) [] (2) (3) (4) (5) Linearity [] Chattering [] Insulation [] Endurance [] X1.0%, Y1.0% (See Figure 10-2) 15ms 20M/25V(DC) No acting damage at DC50V/60sec. Figure 6-1 Loop Resistance X = short RT and RL , short LT and LL , measure the resistance between RT and LT Loop Resistance Y = short RT and LT , short RL and LL ,measure the resistance between RT and RL Date: May 06, 2008 Version: 6.3 Page: 04/11 07. Mechanical Characteristics [] Item [] Operating Force Stylus=R0.8 [] [=R0.8] Impact 13.0DIA. Steel Ball/9g Height=30cm 1 time, no damage [Impact at center area] [13/9g [ 1 ,] [] Static Load [] Specification [] Condition [] 50g =30cm] 500g within 10cm area for Satisfy(1) of Item 7 and 30sec (1), (2),(4) of Item 6 [500g 10cm30 ] [ 7 (1) 6 (1),(2),(4)] Hardness 3H pencil, pressure 1N/45 [] [ 3H, 1N/45(JIS K5400)] Peeling 800g by vertical 90 Satisfy (1) of Item 6 [] [800g , 90] [ 6 (1)] Bending 13510 times left & right Satisfy (1) of Item 6 [] [135, 10 ] [ 6 (1)] 08. Reliability Item [] [] High Temperature /Humidity [] Specification [] 70C /90%RH, 500 hrs, allow panel stays in normal environment for 4 hrs [] Condition [] Reliability test may cause the film puffed yet the electric characteristic stays intact. (1), [70C /90%RH500 4 (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies ] High temperature 3H 70C /500 hrs allow panel stays X2.0%, Y2.0%;Actuation in normal environment for 4 hrs force must not exceed 150g [70C /500 4 ] after reliability test. Low temperature [] -40C /500 hrs allow panel stays in normal environment for 4 hrs [-40C /500 4 ] [ 5 (1)(2) 6 (1) (4) ; 6 (2) X2.0%, Y Thermal Cycle [] -40C ~70 [60 min./cycle] *100 cycles allow panel stays in normal environment for 4 hrs 2.0%; 150g] [-40C ~70C 60 100 4 ] 09. Durability Item [] Specification [] [] Condition [] Satisfy (1), (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies X2.0%, Y2.0%; Knock Test 35,000,000 times [] [3500 ] Actuation force must not exceed 150g after durability test. [ 5 (1)(2) 6 (1) (4) ; 6 (2) X2.0%, Y 2.0%; 150g] Date: May 06, 2008 Version: 6.3 Page: 05/11 10. Inspection Methods [] (1) Linearity Condition [] Step 1: short RT and RL(or short RL and LL). Step 2: apply voltage DC 5V. Step 3: short LT and LL (or short RT and LT). Step 4: apply grounding. Step 5: draw points along LX and LY at 5.0mm intervals within pattern area and detect the voltage at SG. Step 6: measure the voltage differences between RT and LT (or RT and RL) (Fig 10-1) (Fig 10-2) [ RT , RL ( RL , LL ) 5V , LT , LL ( RT , LT ) 0V , 5.0mm , (stylus)( 2 LX LY), SG , RT LT ( RT RL ) ] (Fig 10-1) (Fig 10-2) Figure 10-1 Figure 10-2 Linearity: [Vxm-Vxi] / (Va-Vb) X 100% (2) Specification [] Linearity must meet the electrical characteristic specified in Item 6 [ 6 ] Date: May 06, 2008 Version: 6.3 Page: 06/11 11. Appearance Inspection (1) A 17W fluorescent luminant lamp is used for appearance inspection. Detail settings are shown in (Fig 11-1) and (Fig 11-2). [] [(1) 17W (Fig11-1), (Fig11-2) ] (2) Minor impurities outside viewing area are acceptable unless their existance affect electrical functions. [(2) ] . Figure 11-1 Figure 11-2 (3) Glass Flaw [] Item [] Picture [] Specification [ ] X3.0mm Y3.0mm ZT Corner Flaw [] X3.0mm Y3.0mm ZT Edge Flaw [] Progressive Flaw Not allowed [] [] Note: T=Glass thickness (4) Please refer to AppendixAppearance Specification. [(4)( 1)] Date: May 06, 2008 Version: 6.3 Page: 07/11 12. Attention of Mounting Condition [] (1) The gasket support of touch panel must allocate outside of Viewable Area. Reserve enough clearance between panel surface and enclosure for normal panel operation. To avoid pressing error, please retain enough space between surface panel and Bezel. [(support)(Viewable area) ] (2) Bezel opening must not touch Viewable Area, Bezel opening must be designed between Viewable Area and Active Area. [(Bezel opening)] (3) We recommend elastic material support. [] (4) Due to the conductive characteristic of the panel backside, prevent metal contact after mounting. [