PRELIMINARY DATASHEET TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER ICS281 Description Features The ICS281 field programmable spread spectrum clock synthesizer generates up to three high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency crystal input. It is designed to replace crystals, crystal oscillators and stand alone spread spectrum devices in most electronic systems. * * * * * * * * * * * * * Using ICS' VersaClockTM software to configure PLLs and outputs, the ICS281 contains a One-Time Programmable (OTP) ROM for field programmability. Programming features include input/output frequencies, spread spectrum amount and eight selectable configuration registers. Using Phase-Locked Loop (PLL) techniques, the device runs from a standard fundamental mode, inexpensive crystal, or clock. It can replace multiple crystals and oscillators, saving board space and cost. Packaged as 16-pin TSSOP Eight addressable registers Replaces multiple crystals and oscillators Output frequencies up to 200 MHz at 3.3 V Configurable Spread Spectrum Modulation Input crystal frequency of 5 to 27 MHz Input clock frequency of 3 to 166 MHz Up to three reference outputs Operating voltages of 3.3 V VDDO output control from 1.8 V to 3.3 V Controllable output drive levels Advanced, low-power CMOS process Available in Pb (lead) free packaging The ICS281 is also available in factory programmed custom versions for high-volume applications. Block Diagram VDD S2:S0 3 OTP ROM with PLL Values Crystal or clock input 3 VDDO PLL1 with Spread Spectrum Divide Logic and Output Enable Control PLL2 PLL3 CLK1 CLK2 CLK3 X1/ICLK Crystal Oscillator X2 External capacitors are required with a crystal input. GND 3 PDTS IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 1 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Pin Assignment GND 16 S2 2 15 3 14 VDD 4 13 VDD PDTS GND VDDO CLK1 5 6 12 11 CLK2 GND 7 10 VDD X1/ICLK 8 9 S0 S1 1 CLK3 X2 16 pin (173 mil) TSSOP Pin Descriptions Pin Number Pin Name Pin Type 1 GND Power Connect to ground. 2 S0 Input Select pin 0. Internal pull-up resistor. Select pin 1. Internal pull-up resistor. Connect to +3.3 V. Pin Description 3 S1 Input 4 VDD Power 5 VDDO Power Power supply for outputs. 6 CLK1 Output Output clock 1. Weak internal pull-down when tri-state. 7 GND Power Connect to ground. 8 X1 XI Crystal input. Connect this pin to a crystal or external input clock. 9 X2 XO 10 VDD Power Crystal Output. Connect this pin to a crystal. Float for clock input. Connect to +3.3 V. 11 CLK2 Output Output clock 2. Weak internal pull-down when tri-state. 12 CLK3 Output Output clock 3. Weak internal pull-down when tri-state. 13 GND Power Connect to ground. 14 PDTS Input 15 VDD Power Power-down tri-state. Powers down entire chip and tri-states clock outputs when low. Internal pull-up resistor. Connect to +3.3 V. 16 S2 Input Select pin 2. Internal pull-up resistor. IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 2 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER External Components EPROM CLOCK SYNTHESIZER The ICS281 requires a minimum number of external components for proper operation. The ICS281 also provides separate output divide values, from 2 through 63, to allow the two output clock banks to support widely differing frequency values from the same PLL. Series Termination Resistor Each output frequency can be represented as: Clock output traces over one inch should use series termination. To series terminate a 50 trace (a commonly used trace impedance), place a 33 resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20. Decoupling Capacitors As with any high-performance mixed-signal IC, the ICS281 must be isolated from system power supply noise to perform optimally. OutputFreq = REFFreq ----M N Output Drive Control The ICS281 has two output drive settings. For VDDO=VDD, low drive should be selected when outputs are less than 100 MHz. High drive should be selected when outputs are greater than 100 MHz. Decoupling capacitors of 0.01F must be connected between each VDD and the PCB ground plane. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias on the decoupling circuit. For VDDO<2.8 V, high drive should be selected for all output frequencies. Crystal Load Capacitors ICS VersaClock Software The device crystal connections should include pads for small capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) been the crystal and device. Crystal capacitors must be connected from each of the pins X1 and X2 to ground. ICS applies years of PLL optimization experience into a user friendly software that accepts the user's target reference clock and output frequencies and generates the lowest jitter, lowest power configuration, with only a press of a button. The user does not need to have prior PLL experience or determine the optimal VCO frequency to support multiple output frequencies. The value (in pF) of these crystal caps should equal (CL -6 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 20 pF [(16-6) x 2] = 20. ICS281 Configuration Capabilities The architecture of the ICS281 allows the user to easily configure the device to a wide range of output frequencies, for a given input reference frequency. The frequency multiplier PLL provides a high degree of precision. The M/N values (the multiplier/divide values available to generate the target VCO frequency) can be set within the range of M = 1 to 1024 and N = 1 to 32,895. (Consult the AC Electrical Characteristics for output rise and fall times for each drive option.) VersaClock software quickly evaluates accessible VCO frequencies with available output divide values and provides an easy to understand, bar code rating for the target output frequencies. The user may evaluate output accuracy, performance trade-off scenarios in seconds. Spread Spectrum Modulation The ICS281 utilizes frequency modulation (FM) to distribute energy over a range of frequencies. By modulating the output clock frequencies, the device effectively lowers energy across a broader range of frequencies; thus, lowering a system's electromagnetic interference (EMI). The modulation rate is the time from transitioning from a minimum frequency to a maximum frequency and then back to the minimum. IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 3 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER Spread Spectrum Modulation can be applied as either "center spread" or "down spread". During center spread modulation, the deviation from the target frequency is equal in the positive and negative directions. The effective average frequency is equal to the target frequency. In applications where the clock is driving a component with a maximum frequency rating, down spread should be applied. In this case, the maximum frequency, including modulation, is the target frequency. The effective average frequency is less than the target frequency. The ICS281 operates in both center spread and down spread modes. For center spread, the frequency can be modulated between 0.125% to 2.0%. For down spread, the frequency can be modulated between -0.25% to -4.0%. EPROM CLOCK SYNTHESIZER Both output frequency banks will utilize identical spread spectrum percentage deviations and modulation rates, if a common VCO frequency can be identified. Spread Spectrum Modulation Rate The spread spectrum modulation frequency applied to the output clock frequency may occur at a variety of rates. For applications requiring the driving of "down-circuit" PLLs, Zero Delay Buffers, or those adhering to PCI standards, the spread spectrum modulation rate should be set to 30-33 kHz. For other applications, a 120 kHz modulation option is available. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS281. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Parameter Condition Min. Supply Voltage, VDD Referenced to GND Inputs Referenced to GND Clock Outputs Referenced to GND Max. Units 7 V -0.5 VDD+0.5 V -0.5 VDD+0.5 V -65 150 C 260 C 125 C Storage Temperature Soldering Temperature Typ. Max 10 seconds Junction Temperature Recommended Operation Conditions Parameter Min. Typ. Max. Units Ambient Operating Temperature (ICS281PG/PGLF) 0 +70 C Ambient Operating Temperature (ICS281PGI/PGILF) -40 +85 C Power Supply Voltage (measured in respect to GND) +3.135 +3.465 V 4 ms Power Supply Ramp Time IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 4 +3.3 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 5%, Ambient Temperature -40 to +85C Parameter Operating Voltage Symbol Conditions VDD VDDO Voltage Min. Typ. Max. Units 3.135 3.465 V 1.80 VDD V Config. Dependent - See VersaClockTM Estimates Operating Supply Current Input High Voltage IDD mA Three 33.3333 MHz outs, VDD=VDDO=3.3V; PDTS = 1, no load, Note 1 20 mA 500 A V Input High Voltage VIH PDTS = 0, no load, Note 1 S2:S0 Input Low Voltage VIL S2:S0 Input High Voltage, PDTS VIH Input Low Voltage, PDTS VIL Input High Voltage VIH ICLK Input Low Voltage VIL ICLK Output High Voltage (CMOS High) VOH IOH = -4 mA Output High Voltage VOH IOH = -8 mA (Low Drive); IOH = -12 mA (High Drive) Output Low Voltage VOL IOL = 8 mA (Low Drive); IOL = 12 mA (High Drive) Short Circuit Current IOS Low Drive 40 High Drive 70 mA 20 Nom. Output Impedance VDD/2+1 0.4 VDD-0.5 V 0.4 ZO V VDD/2+1 V V VDD/2-1 V VDD-0.4 V 2.4 VDDO-0.4 V 0.4 V Internal pull-up resistor RPUS S2:S0, PDTS 190 k Internal pull-down resistor RPD CLK outputs 120 k Input Capacitance CIN Inputs 4 pF Note 1: Example with 25 MHz crystal input, three unloaded 33.3 MHz outputs and VDD = VDDO = 3.3 V. IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 5 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 5%, Ambient Temperature -40 to +85 C Parameter Symbol Input Frequency FIN Output Frequency Conditions Min. Typ. Max. Units Fundamental crystal 5 27 MHz Clock input 3 166 MHz VDDO=VDD 0.314 200 MHz 1.8 V<VDDO<2.8 V 0.314 150 MHz Output Rise/Fall Time tOF 80% to 20%, high drive, Note 1 1.0 ns Output Rise/Fall Time tOF 80% to 20%, low drive, Note 1 2.0 ns Output Rise/Fall Time tOF 80% to 20%, high drive, 1.8 V<VDDO<2.8 Note 2 2.0 ns Duty Cycle Note 2 Output Frequency Synthesis Error Configuration Dependent Power-up Time PLL lock-time from power-up One Sigma Clock Period Jitter Maximum Absolute Jitter tja 40 49-51 60 TBD % ppm 4 10 ms PDTS goes high until stable CLK output, Spread Spectrum Off 0.6 2 ms PDTS goes high until stable CLK output, Spread Spectrum On 4 7 ms Configuration Dependent 50 ps Deviation from Mean. Configuration Dependent +200 ps Note 1: Measured with 15 pF load. Note 2: Duty Cycle is configuration dependent. Most configurations are min 45% / max 55%. Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case Symbol Conditions Min. Typ. Max. Units JA Still air 78 C/W JA 1 m/s air flow 70 C/W JA 3 m/s air flow 68 C/W 37 C/W JC IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 6 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER Marking Diagrams EPROM CLOCK SYNTHESIZER Marking Diagrams (Pb free) 16 9 16 9 281PGL ###### YYWW 281PG ###### YYWW 1 8 1 8 16 9 16 9 281PGIL ###### YYWW 281PGI ###### YYWW 1 8 1 8 Notes: 1. ###### is the lot number. 2. YYWW is the last two digits of the year and week that the part was assembled. 3. "I" denotes industrial temperature range (if applicable). 4. "L" denotes Pb (lead) free package. 5. Bottom marking: country of origin. IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 7 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Package Outline and Package Dimensions (16-pin TSSOP, 173 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 24 Millimeters Symbol E1 INDEX AREA A A1 A2 b C D E E1 e L E 1 2 D Min Inches Max Min -- 1.20 0.05 0.15 0.80 1.05 0.19 0.30 0.09 0.20 4.90 5.10 6.40 BASIC 4.30 4.50 0.65 Basic 0.45 0.75 0 8 Max -- .047 0.002 0.006 0.032 0.041 0.007 0.012 0.0035 0.008 0.193 0.201 0.252 BASIC 0.169 0.177 0.0256 Basic .018 .030 0 8 A A2 A1 c - Ce b SEATING PLANE .10 (.004) C IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 8 L ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Ordering Information Part / Order Number Marking Shipping Packaging Tubes 16-pin TSSOP 0 to +70C See page 7 Tubes 16-pin TSSOP -40 to +85C ICS281PGLF Tubes 16-pin TSSOP 0 to +70C ICS281PGILF Tubes 16-pin TSSOP -40 to +85C ICS281PG ICS281PGI Package Temperature ICS281G-XX Tubes 16-pin TSSOP 0 to +70C ICS281GI-XX Tubes 16-pin TSSOP -40 to +85C ICS281G-XXLF Tubes 16-pin TSSOP 0 to +70C ICS281GI-XXLF Tubes 16-pin TSSOP -40 to +85C ICS281G-XXT Tape and Reel 16-pin TSSOP 0 to +70C ICS281GI-XXT Tape and Reel 16-pin TSSOP -40 to +85C ICS281G-XXLFT Tape and Reel 16-pin TSSOP 0 to +70C ICS281GI-XXLFT Tape and Reel 16-pin TSSOP -40 to +85C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. The ICS281G-XX, ICS281G-XXLF, ICS281GI-XX, and ICS281GI-XXLF are factory programmed versions of the ICS281PG, ICS281PGLF, ICS281PGI, and ICS281PGILF. A unique "-XX" suffix is assigned by the factory for each custom configuration, and a separate data sheet is kept on file. For more information on custom part numbers programmed at the factory, please contact your local IDT sales and marketing representative. While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. VersaClockTM is a trademark of Integrated Circuit Systems, Inc. All rights reserved. IDTTM / ICSTM TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 9 ICS281 REV C 061306 ICS281 TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 <product line email> <product line phone> Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 (c) 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA