Automotive Relays Plug-in Micro ISO Relays Micro Relay A/VFMA High current version with limiting continuous current 30A at 85C Pin assignment according to ISO 7588 part 3 Customized versions on request - 24VDC versions with special contact gap - Integrated components (e.g. diode) - Customized marking - Special covers (e.g. notches, release features) - For latching version refer to Micro Relay Latching - For low noise version refer to Micro Relay Low Noise - For high current version refer to part number table Typical applications Cross carline up to 30A for example: ABS control, blower fans, cooling fan, door control, door lock, fuel pump, heated front screen, immobilizer, interior lights, seat control, seatbelt pretensioner, sun roof, trunk lock, valves, window lifter, wiper control. F074_fcw1_bw FVFMA_fcw1c Contact DataForm A Standard Form C Form A HC Form C HC Contact arrangement 1 form A, 1 form A, 1 form C, 1 form C, 1 form A, 1 form C 1 NO 1 NO 1 CO 1 CO 1 NO 1 CO Rated voltage 12VDC 24VDC 12VDC 24VDC6) 12VDC 12VDC Limiting continuous current, form A/form B NO/NC NO/NC 23C 30A 30A 30/20A 30/20A 35A 35/25A 85C 25A 25A 25/15A 25/15A 30A 30/20A 125C 10A 10A 10/8A 10/8A 15A 15/10A Limiting making current1)2), A/B (NO/NC) 120A 120A 120/40A 120/20A 120A 120/40A Limiting breaking current 30A 20A 30/15A 20/10A 30A 30/20A Limiting short-time current, overload current, ISO 8820-33) 1.35 x 25A, 1800s 1.35 x 25A, 1800s1.35 x 30A, 1800s 2.00 x 25A, 5s 2.00 x 25A, 5s 2.00 x 30A, 5s 3.50 x 25A, 0.5s 3.50 x 25A, 0.5s 3.50 x 30A, 0.5s 6.00 x 25A, 0.1s 6.00 x 25A, 0.1s 6.00 x 30A, 0.1s Jump start test24VDC for 5min conducting nominal current at 23C Contact material silver based Min. recommended contact load4) 1A at 5VDC Initial voltage drop NO contact at 10A, typ./max. 15/200mV NC contact at 10A, typ./max. 20/250mV Frequency of operation 6 ops./min (0.1Hz) Electrical endurance5) resistive load at 14VDC >1x105 ops. >1x105 ops. >1x105 ops. 25A 25A (NO) 30A resistive load at 28VDC >1x105 ops. >1x105 ops. 15A 15A (NO) >1x105 ops. 10A (NC) Mechanical endurance typ. 107 ops. Max. DC load breaking capacity 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages. 2) For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the specified current. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) Electrical endurance data is not valid for diode versions. Any diode or pn-junction parallel to the coil (internal or external) will significantly decrease the electrical lifetime, especially when used for inductive loads. 6) Not applicable for polarity reverse loads like power windows Load limit curve 1: arc extinguishes during transit time (CO contact). Load limit curve 2: safe shutdown, no stationary arc (NO contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. 12-2017, Rev. 1217 www.te.com (c) 2017 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 1 Automotive Relays Plug-in Micro ISO Relays Micro Relay A/VFMA (Continued) Coil Data Coil voltage range Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001 12 7.2 002 24 14.4 005 12 7.2 F 12 7.2 H 24 14.4 Other Data 12/24VDC Release voltage VDC 1.6 3.6 1.6 1.2 3.6 Coil resistance7) 10% 119 430 144 90 430 Rated coil power7) W 1.20 1.34 1.00 1.60 1.34 All figures are given for coil without pre-energization, at ambient temperature +23C. 7) Without components in parallel. Coil operating range TE074_OVR1 Does not take into account the temperature rise due to the contact current E = pre-energization. 8) No change in the switching state >10s. Valid for NC contacts, NO contact values significantly higher. 9) Values apply 2mm from the end of the terminal. When the force is removed, the terminal must not have moved by more than 0.3mm Insulation Data Initial dielectric strength between open contacts between contact and coil Load dump test ISO 7637-1 (12VDC), test pulse 5 ISO 7637-2 (24VDC), test pulse 5 EU RoHS/ELV compliance compliant Ambient temperature -40 to +125C Climatic cycling with condensation, EN ISO 6988 6 cycles, storage 8/16h Temperature cycling, IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C Damp heat constant, IEC 60068-2-3 (78), Ca 56 days Category of environmental protection, IEC 61810 RT I - dustproof Degree of protection, IEC 60529 IP54 Corrosive gas IEC 60068-2-42 102cm3/m3 SO2, 10 days IEC 60068-2-43 10.3cm3/m3 H2S, 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep) 10 to 500Hz min. 5g8) Shock resistance (functional) IEC 60068-2-27 (half sine) min. 20g 11ms8) Drop test, free fall, IEC 60068-2-32 1m onto concrete Terminal type plug-in, QC Cover retention axial force 150N Does not take into account pull force 150N the temperature rise due to push force 200N the contact current retention E =Terminal pre-energization pull force 100N push force 100N resistance to bending 10N9) force applied to side 10N9) torque 0.3Nm Weightapprox. 16 to 20g (0.5 to 0.7oz) Packaging unit Micro A 480 pcs. VFMA 600 pcs. 500VACrms 500VACrms Accessories For details see datasheet Connectors for Micro ISO Relays Vs=+86.5VDC Vs=+200VDC Terminal Assignment NOD 1 form A, 1 NO with diode 2 NOR 1 form A, 1 NO with resistor COD 1 form C, 1 CO with diode 2 5 2 5 2 1 3 1 3 1 12-2017, Rev. 1217 www.te.com (c) 2017 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. 5 4 3 Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions COR 1 form C, 1 CO with resistor 2 1 5 4 3 Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. Automotive Relays Plug-in Micro ISO Relays Micro Relay A/VFMA (Continued) Dimensions Quick connect terminal similar to ISO 8092-1. Micro A: Terminals without holes VFMA: Terminals with holes View of the terminals (bottom view) 12-2017, Rev. 1217 www.te.com (c) 2017 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 3 Automotive Relays Plug-in Micro ISO Relays Micro Relay A/VFMA (Continued) Product code structure V23074 Typical product code -A 1 001 -A4 02 1 F 4 1 -S01 Type V23074 Micro Relay A Version A Standard Coil suppression 1 Resistor Coil 001 12VDC Contact material -A4 Silver based Contact arrangement 02 1 form A, 1 NO H High current 2 Diode 002 24VDC -A5 Silver based for high current version 03 1 form C, 1 CO 005 Product code structure 12VDC for high current version VFMA Typical product code -1 Type VFMA VFMA Series Version 1 Standard Contact arrangement 1 1 form A, 1 NO Coil F 12VDC Contact material 4 Silver based Terminals 1 Plug-in Coil suppression S01 Resistor Product code V23074-A1001-A402 VFMA-11F41-S01 V23074-A1001-A403 VFMA-15F41-S01 V23074-A2001-A402 V23074-A2201-X147 V23074-A2001-A403 V23074-A2101-X148 V23074-H1005-A502 V23074-A1002-A402 VFMA-11H41-S01 V23074-A1002-A403 V23074-A2002-A402 V23074-A2002-A403 Equivalent to VFMA-11F41-S01 V23074-A1001-A402 VFMA-15F41-S01 V23074-A1001-A403 V23074-A2201-X147 V23074-A2001-A402 V23074-A2101-X148 V23074-A2001-A403 VFMA-11H41-S01 V23074-A1002-A402 5 1 form C, 1 CO H 24VDC 7 Silver based for high current version Version Standard Coil suppr. Circuit1) Resistor 680 NOR Arrangement Cover Coil Color Black 12VDC 1 form A, 1 NO COR Diode NOD COD High current Resistor 1000 Standard Resistor 1800 NOR Blue Black Red Black 4-1904124-2 9-1393292-9 4-1904124-3 1393293-8 5-1393292-8 5-1904135-9 6-1419137-4 6-1904135-0 4-1904124-4 8-1393292-9 6-1415008-2 3-1393292-8 6-1393292-2 6-1393292-3 Terminals Part number 1 form A, 1 NO 1 form C, 1 CO 24VDC Part number Plug-in, QC 1 form C, 1 CO COR NOD COD Diode Terminals 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form C, 1 CO 1) See terminal assignment diagrams. Other types on request. This list represents the most common types and does not show all variants covered by this datasheet. Production in Asia (only) Product code V23074-A1001-A402 V23074-A1001-A403 V23074-A2001-A402 V23074-A2001-A403 V23074-H1005-A502 Version Standard Coil suppression Resistor 680 Diode High current Resistor 1000 Circuit1) NOR COR NOD COD NOR Cover Color Black Coil 12VDC Arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO Plug-in, QC 1393292-5 8-1393292-4 2-1904111-7 9-1904105-7 2-1414971-4 1) See terminal assignment diagrams. Other types on request. This list represents the most common types and does not show all variants covered by this datasheet. 4 12-2017, Rev. 1217 www.te.com (c) 2017 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change.