CSD02060-Silicon Carbide Schottky Diode VRRM = 600V Zero Recovery(R) Rectifier IF(AVG)= 2A Qc Features * * * * * * * = 7nC Package 600-Volt Schottky Rectifier Zero Reverse Recovery Zero Forward Recovery High-Frequency Operation Temperature-Independent Switching Behavior Extremely Fast Swtitching Positive Temperature Coefficient on VF TO-263-2 TO-220-2 Benefits * * * * * Replace Bipolar with Unipolar Rectifiers Essentially No Switching Losses Higher Efficiency Reduction of Heat Sink Requirements Parallel Devices Without Thermal Runaway PIN 1 CASE PIN 2 Applications * * * Switch Mode Power Supplies Power Factor Correction - Typical PFC Pout : 200W-400W Motor Drives - Typical Power : 0.50HP-1.0HP Part Number Package Marking CSD02060A TO-220-2 CSD02060 CSD02060G TO-263-2 CSD02060 Maximum Ratings D02060 Rev. Datasheet: CS Symbol Parameter Value Unit Test Conditions VRRM Repetitive Peak Reverse Voltage 600 V VRSM Surge Peak Reverse Voltage 600 V VDC DC Blocking Voltage 600 V IF(AVG) Average Forward Current 2 3.5 A TC=150C, DC TC=125C, DC IF(PEAK) Peak Forward Current 5 A TC=125, TREP<1mS, Duty=0.5 IFRM Repetitive Peak Forward Surge Current 10 A TC=25C, tP=8.3ms, Half Sine Wave IFSM Non-Repetitive Peak Forward Surge Current 40 A TC=25C, tP=10s, Pulse Ptot Power Dissipation 43 14 W TC=25C TC=125C -55 to +175 C TJ , Tstg Operating Junction and Storage Temperature Subject to change without notice. www.cree.com/power Note Electrical Characteristics Symbol Parameter Typ. Max. Unit Test Conditions VF Forward Voltage 1.6 2.0 1.8 2.4 V IR Reverse Current 50 100 200 1000 A VR = 600V TJ=25C VR = 600V TJ=175C QC Total Capacitive Charge 7 nC VR = 600V, IF = 1A di/dt = 500 A/s TJ = 25C C Total Capacitance 120 20 15 pF VR = 0V, TJ = 25C, f = 1MHz VR = 200V, TJ = 25C, f = 1MHz VR = 400V, TJ = 25C, f = 1MHz Note IF = 2A TJ=25C IF = 2A TJ=175C Note: 1. This is a majority carrier diode, so there is no reverse recovery charge. Thermal Characteristics Symbol Parameter Typ. Max. Unit RJC Thermal Resistance from Junction to Case 4.7 C/W RJA Thermal Resistance from Junction to Ambient 53 C/W Test Conditions Note Typical Performance 124 200 11 180 TJ = 25C 10 TJ = 75C 160 TJ = 125C TJ = 175C IR Reverse Current (A) IF Forward Current (A) 93 8 7 62 5 4 140 120 TJ = 25C TJ = 75C 100 TJ = 125C TJ = 175C 80 60 31 40 2 20 1 00 0.0 0 0.5 1.0 1.5 2.0 2.5 VF Forward Voltage (V) Figure 1. Forward Characteristics CSD02060 Rev. - 3.0 3.5 0 200 400 600 VR Reverse Voltage (V) Figure 2. Reverse Characteristics 800 Typical Performance 250 100 20 186 200 80 5 14 C Capacitance (pF) IF(AV) Forward Current (A) IF(AVG) Forward Current (A) 16 124 10 3 8 62 150 60 100 40 50 20 4 1 2 00 25 25 50 50 75 75 100 100 125 125 150 150 175 175 00 200 200 1 TC Case Temperature (C) 10 100 1000 VR Reverse Voltage (V) Figure 3. Current Derating Figure 4. Capacitance vs. Reverse Voltage 1.00E+01 Zth [C/W] 1.00E+00 1.00E-01 1.00E-02 1.00E-03 1.00E-07 1.00E-06 1.00E-05 1.00E-04 1.00E-03 time [s] Figure 5. Transient Thermal Impedance CSD02060 Rev. - 1.00E-02 1.00E-01 1.00E+00 Package Dimensions POS Package TO-220-2 Inches Max Min Max A .402 .408 10.211 10.364 B .120 .124 3.048 3.150 C .106 .110 2.692 2.794 D .245 .251 6.223 6.375 E .335 .345 8.509 8.763 F .149 .153 3.784 3.886 G .220 .240 5.588 6.096 H .540 .550 13.716 13.970 J .100 REF K PIN 1 CASE PIN 2 Millimeters Min 2.540 REF .080 2.032 L .050 .056 1.270 1.422 M .032 .038 .813 .956 N .197 .203 5.004 5.156 4.572 P .170 .180 4.318 Q .048 .052 1.219 1.321 R .583 .593 14.808 15.062 S 6.5 8.5 6.5 8.5 T 6.5 8.5 6.5 8.5 U 6.5 8.5 6.5 8.5 V .103 .107 2.616 2.718 W .015 .021 .381 .533 X 2.0 4.0 2.0 4.0 Y .396 .406 10.058 10.312 NOTE: 1. Dimension L, M, W apply for Solder Dip Finish. Package Dimensions POS Package TO-263-2 Inches Max Min Max A .396 .406 10.058 10.312 B .297 .303 7.544 7.696 C .057 .063 1.448 1.600 D .237 .243 6.015 6.167 E .050 .070 1.270 1.778 F .048 .052 1.219 1.321 G PIN 1 CASE PIN 2 CSD02060 Rev. - Millimeters Min .100 TYP 2.540 TYP H .335 .345 8.509 8.763 J .028 .032 .711 .813 K 2 4 2 4 L .170 .180 4.318 4.572 M .048 .052 1.219 1.321 N .595 .615 15.113 15.621 P 0.00 0.10 0.00 .254 Q R0.018 TYP R0.022 TYP R0.457 TYP R0.559 TYP R .090 .110 2.286 2.794 S .013 .017 .330 .432 T 6.5 8.5 6.5 8.5 U .103 .107 2.616 2.718 V R0.028 TYP R0.032 TYP R0.711 TYP R0.813 TYP W -- 5.0 -- 5.0 Recommended Solder Pad Layout TO-263-2 TO-220-2 Part Number Package Marking CSD02060A TO-220-2 CSD02060 CSD02060G TO-263-2 CSD02060 This product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defibrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, air traffic control systems, or weapons systems. Copyright (c) 2006 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, and Zero Recovery are registered trademarks of Cree, Inc. CSD02060 Rev. - Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5451 www.cree.com/power