Finisar Product Specification 4 Gigabit RoHS Compliant CWDM SFP Transceiver FWLF1524P2yxx PRODUCT FEATURES Up to 4.25Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions CWDM DFB laser transmitter Duplex LC connector RoHS compliant and Lead Free Up to 30 km on 9/125 m SMF at 4.25 Gb/s Metal enclosure, for lower EMI Single 3.3V power supply Commercial operating temperature range: -5C to 75C APPLICATIONS Metro Access Rings and Point-toPoint networking for Gigabit Ethernet and Fibre Channel Link concatenation/aggregation Finisar's FWLF1524P2yxx Small Form Factor Pluggable (SFP) transceiver is compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. The transceiver is designed for operation in Metro Access Rings and Point-to-Point networks using Fibre Channel2 Gigabit Ethernet3 networking equipment by selecting the appropriate line rate. The FWLF1524P2yxx available in eight different CWDM wavelengths; and is RoHS compliant and lead-free per Directive 2002/95/EC4 and Finisar Application Note AN-2038. Finisar Corporation April, 2012 Rev E Page 1 Finisar PRODUCT SELECTION FWLF1524P2yxx y L V xx Wavelength 1471 nm 1491 nm 1511 nm 1531 nm xx 47 49 51 53 Non Rate Selectable - 1x, 2x, 4x Fibre Channel Rate Selectable - 1x, 2x, 4x Fibre Channel and Gigabit Ethernet CWDM Wavelength (see table below) Clasp Color Code Gray Violet Blue Green Finisar Corporation April, 2012 Rev E Wavelength 1551 nm 1571 nm 1591 nm 1611 nm xx 55 57 59 61 Clasp Color Code Yellow Orange Red Brown Page 2 Finisar FWLF1524P2yxx SFP Product Specification - April 2012 I. Pin Descriptions Pin 1 2 3 4 5 6 7 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select 8 9 10 11 12 13 14 15 16 17 18 19 20 LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. Open or Low = 1.063 Gb/s or 2.125 Gb/s Fibre Channel, 1.25 Gb/s Gigabit Ethernet (Low Bandwidth) High = 2.125 or 4.25 Gb/s Fibre Channel (High Bandwidth) Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Specific information when selecting line rate: Rate selection is done in accordance with SFF Committee SFF-8079 Draft, Rev.1.6, Table 3. Note that rate select can also be set through 2-wire bus in accordance with SFF-84726 at Bit 3, Byte 110, Address A2h (note: writing `1' selects full bandwidth operation). Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. Non Rate Selectable version can operate at 1x, 2x, 4x Fibre Channel independent of rate select pin setting. 5. LOS is open collector output. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 1 2 Towards Bezel 20 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeT TD- VeeT Towards ASIC VeeR Pinout of Connector Block on Host Board Finisar Corporation April, 2012 Rev E Page 3 Finisar FWLF1524P2yxx SFP Product Specification - April 2012 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Symbol Vcc TS Min -0.5 -40 TOP RH -5 0 Case Operating Temperature Relative Humidity III. Typ Max 4.5 85 Unit V C 75 85 C % Ref. 1 Electrical Characteristics (TOP = -5 to 75 C, VCC = 3.1 to 3.5 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise/fall time < 4.25 Gb/s Data output rise/fall time = 4.25 Gb/s LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter Contribution < 4.25 Gb/s Total Jitter Contribution < 4.25 Gb/s Deterministic Jitter Contribution = 4.25 Gb/s Total Jitter Contribution = 4.25 Gb/s Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr, tf tr, tf VLOS fault VLOS norm PSR RX DJ Min 3.1 Typ Max 3.5 300 Unit V mA 250 Vcc - 1.3 Vee 1200 Vcc Vee+ 0.8 10 mV V V us 250 800 175 120 VccHOST Vee+0.5 51.7 mV ps ps V V mVpp ps 4 5 5 6 6 7 8 8 100 Vcc - 0.5 Vee 100 Ref. 2 RX RX TJ DJ 122.4 25.9 ps ps RX TJ 61.2 ps 3 Notes: 1. Non-condensing. 2. AC coupled. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 - 80 % 6. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA) 1, September 14, 2000. 8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. Finisar Corporation April, 2012 Rev E Page 4 Finisar FWLF1524P2yxx SFP Product Specification - April 2012 IV. Optical Characteristics (TOP = -5 to 75 C, VCC = 3.1 to 3.5 Volts) Parameter Transmitter Output Opt. Power (Rate Select High) Output Opt. Power (Rate Select Low) Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Extinction Ratio (Rate Select High) Optical Extinction Ratio (Rate Select Low) Optical Rise/Fall Time = 4.25 Gb/s Optical Rise/Fall Time 2.125 Gb/s RIN Deterministic Jitter Contribution = 4.25 Gb/s Total Jitter Contribution = 4.25 Gb/s Deterministic Jitter Contribution 2.125 Gb/s Total Jitter Contribution 2.125 Gb/s Receiver Receiver Sensitivity = 4.25 Gb/s Symbol Min PO,RH PO,RL +1 +1 X-6.5 OMA ER ER tr/ tf tr/ tf TX TX TX TX Receiver Sensitivity = 1.06 Gb/s RSENS1 Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. = 1.25 Gb/s Average Received Power Receiver Electrical 3dB cutoff freq. Receiver Electrical 3dB cutoff freq. Optical Center Wavelength Return Loss LOS De-Assert LOS Assert LOS Hysteresis RSENS-GE RxMAX C LOSD LOSA Unit +5 +5 X+6.5 1 dBm dBm nm nm uW dB dB ps ps dB/Hz ps ps ps ps 1 2 3 3 4 uW dBm uW dBm uW dBm dBm dBm dBm MHz MHz nm dB dBm dBm dB 8 9 8 9 8 10 10 105 160 -118 28.2 59.8 56.5 119 RSENS4 RSENS2 X Max 290 4 9 DJ TJ DJ TJ Receiver Sensitivity = 2.125 Gb/s Typ 1450 12 29 -16.5 15 -20.5 15 -22.0 -22 -14.5 0 1500 2500 1620 -19 -30 0.5 Ref. 5 6 7 7 11 12 Notes: 1. High Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Low Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 3. Over case temperature of -5 to 75 C. The Transmitter Center Wavelength "X" is as specified by the customer. The current available wavelengths are: 1471, 1491, 1511, 1531, 1551, 1571, 1591, and 1611 nm. Please see the "Product Selection" section on page 2. 4. Equivalent extinction ration specification for Fibre Channel. Allows smaller ER at higher average power 5. Unfiltered, 20-80% measured w/ a "00001111" pattern. Complies with FC 4x eye mask when filtered. 6. Unfiltered, 20-80% measured w/ a "00001111" pattern. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered. 7. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. 8. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications. Value in OMA. Measured with PRBS 27-1 at 10-12 BER. 9. Represents sensitivity at minimum Extinction Ratio with rate select high. Measured with PRBS 2 7-1 at 10-12 BER. Finisar Corporation April, 2012 Rev E Page 5 Finisar FWLF1524P2yxx SFP Product Specification - April 2012 10. Represents sensitivity at minimum Extinction Ratio with rate select low. Measured with PRBS 2 7-1 at 10-12 BER 11. Rate Selectable version in low bandwidth mode. 12. Rate Selectable version in high bandwidth mode. V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125 m SMF @ 4X Fibre Channel Max. Supported Link Length on 9/125 m SMF @ 1X and 2X Fibre Channel Max. Supported Link Length on 9/125 m SMF @ Gigabit Ethernet Symbol BR BER LMAX1 Min 1062 Typ Max 4250 10-12 30 Units Ref. Mb/sec 1 2 km 3 LMAX2 50 km 3 LMAX3 50 km 3 Notes: 1. Gigabit Ethernet and 1x/2x/4x Fibre Channel compliant. 2. Tested with a PRBS 27-1 test pattern. 3. A 3 dB penalty is included for dispersion on data rates >2Gb/s amd 2dB penalty is included for data rates <2Gb/s. Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application VI. Environmental Specifications Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -5 -40 Typ Max 75 85 Units C C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation April, 2012 Rev E Page 6 Finisar FWLF1524P2yxx SFP Product Specification - April 2012 VIII. Digital Diagnostic Functions All Finisar SFPs support the 2-wire serial communication protocol outlined in the SFP MSA5. These SFPs use an Atmel AT24C01A 128 byte E2PROM with an address of A0h (see table below for E2PROM contents). For details on interfacing with the E2PROM, see the Atmel data sheet titled "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM."6 Finisar's CWDM SFPs also support extended diagnostic features as described in Finisar Applications Note AN-2030, "Digital Diagnostic Monitoring Interface for Optical Transceivers"7, and additional information is available in SFF standard titled: "Digital Diagnostic Monitoring Interface for Optical Transceivers8 (SFF-8472 rev9.3). A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H. I2C clock speed, digital diagnostic accuracy and digital diagnostic range can be found in the table below. Values in the table represent the worst-case values over temperature, voltage, and life. Parameter I2C Clock Speed Accuracy Transceiver Temperature Transceiver Supply Voltage Tx Bias Curent Tx Output Power Received Average Power Range Transceiver Temperature Transceiver Supply Voltage Tx Bias Current Tx Output Power Received Average Power Symbol Min Typ Max Units Notes/Conditions 0 100,000 Hz Bus can be driven blind DDTemperature -5 +5 C Case temperature DDVoltage -3 +3 % DDBias DDTxPower -10 -3 +10 +3 % dB DDRxPower -3 +3 dB DDTemperature -10 80 C DDVoltage 3.0 4.0 V DDBias DDTxPower DDRxPower 0 -10 -25 100 +5 +1 mA dBm dBm Finisar Corporation April, 2012 Rev E 100% tested in production over temp to 2 dB 100% tested in production over temp to 2 dB Page 7 FWLF1524P2yxx SFP Product Specification - April 2012 IX. Finisar Mechanical Specifications Finisar's Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 1. FWLF1524P2Vxx Outline Drawing Finisar Corporation April, 2012 Rev E Page 8 FWLF1524P2yxx SFP Product Specification - April 2012 X. Finisar PCB Layout and Bezel Recommendations Finisar Corporation April, 2012 Rev E Page 9 FWLF1524P2yxx SFP Product Specification - April 2012 Finisar Corporation April, 2012 Rev E Finisar Page 10 FWLF1524P2yxx SFP Product Specification - April 2012 Finisar XI. References 1. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. 2. "Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 10.0)". American National Standard for Information Systems. 3. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2002. 4. Directive 2002/95/EC of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment." January 27, 2003. 5. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 6. "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM", Atmel Corporation. www.Atmel.com 7. "Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers", Finisar Corporation, April 2002. 8. "Digital Diagnostic Monitoring Interface For Optical Transceivers Rev 9.3". SFF Document No. SFF-8472. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation April, 2012 Rev E Page 11