EV-ADF5902SD1Z Evaluation Board User Guide
UG-1432
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the ADF5902 24 GHz, ISM Band, Multichannel FMCW Radar Transmitter
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 Page 1 of 16
FEATURES
Self contained board, including the ADF5902 24 GHz VCO PGA,
with integrated 2-channel PA output and fractional-N
frequency synthesizer with ramp generation
Windows-based software allows control of the ADF5902
functions from a PC
Externally powered by a 5 V power supply
EVALUATION KIT CONTENTS
EV-ADF5902SD1Z evaluation board
EQUIPMENT NEEDED
PC with Windows XP (or more recent version) and USB port for
evaluation software
Analog Devices, Inc., EVAL-SDP-CS1Z SDP-S controller board
Spectrum analyzer
5 V power supply
DOCUMENTS NEEDED
ADF5902 data sheet
PLL Software Installation Guide
SOFTWARE NEEDED
PLL software
GENERAL DESCRIPTION
The EV-ADF5902SD1Z evaluation board allows the user to
evaluate the performance of the ADF5902 24 GHz voltage
controlled oscillator (VCO) programmable gain amplifier (PGA)
with a 2-channel power amplifier (PA ) output and ramping phase-
locked loop (PLL). Figure 1 shows the EV-ADF5902SD1Z
evaluation board, which contains the ADF5902, three high
frequency K type Subminiature Version A (SMA) connectors for
the local oscillator (LO) output, two transceiver outputs, banana
connectors for the power supply, and a connector for the serial
interface.
The EV-ADF5902SD1Z evaluation board requires an
EVAL-SDP-CS1Z system demonstration platform serial
(SDP-S) controller board, which the kit does not include. The
EVAL-SDP-CS1Z SDP-S allows software programming of the
ADF5902 device.
Full specifications on the ADF5902 are available in the ADF5902
data sheet. Consult the data sheet in conjunction with this user
guide when working with the EV-ADF5902SDIZ evaluation board.
The Windows®-based PLL software provides easy programming of
the synthesizer.
EVALUATION BOARD PHOTOGRAPH
17208-001
Figure 1.
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 2 of 16
TABLE OF CONTENTS
Features ............................................................................................... 1
Evaluation Kit Contents ..................................................................... 1
Equipment Needed ............................................................................ 1
Documents needed ............................................................................ 1
Software Needed ................................................................................ 1
General Description ......................................................................... 1
Evaluation Board Photograph ........................................................... 1
Revision History ............................................................................... 2
Evaluation Board Hardware ............................................................ 3
Power Supplies .............................................................................. 3
Input Signals .................................................................................. 3
Output Signals............................................................................... 3
Default Operation .........................................................................3
Evaluation Board Testing ....................................................................4
Evaluation Board Software ...............................................................6
ADF5902 Controls ..........................................................................6
PLL Setup .......................................................................................6
Ramp Generation ...........................................................................7
Evaluation Board Schematics and Artwork ...................................8
Ordering Information .................................................................... 15
Bill of Materials ........................................................................... 15
Related Links ............................................................................... 16
REVISION HISTORY
12/2018—Revision 0: Initial Version
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 3 of 16
EVALUATION BOARD HARDWARE
The EV-ADF5902SD1Z evaluation board requires the use of
an EVAL-SDP-CS1Z SDP-S controller board to program the
device. Purchase the EVAL-SDP-CS1Z SDP-S separately because
it is not included in the evaluation kit. See the Evaluation Board
Schematics and Artwork section for the detailed schematics
(Figure 6 to Figure 12) and layout (Figure 13 and Figure 14) of
the EV-ADF5902SD1Z evaluation board.
POWER SUPPLIES
The EV-ADF5902SD1Z evaluation board is powered by a 5 V
external power supply that must be connected as described in
the Evaluation Board Test section.
INPUT SIGNALS
The 100 MHz temperature controlled crystal oscillator (TCXO),
or an external REF input, provides the necessary reference
signal. Either are acceptable to use.
Connect an external TX_DATA signal to the TPI test point to
control some of the ramping functionality. Use the external REF
input synchronized to TX_DATA when using the TX_DATA
signal. Remove Resistor R40 when using an external REF input.
OUTPUT SIGNALS
The TX1, TX2, and LO outputs from the ADF5902 contain dc
bias voltages, and are available on the J8 (TXOUT1), J9
(TXOUT2), and J4 (LOOUT) output SMAs.
DEFAULT OPERATION
All hardware components necessary to operate the ADF5902 are
included on the EV-ADF5902SD1Z.
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 4 of 16
EVALUATION BOARD TESTING
To evaluate and test the performance of the ADF5902, use the
following procedure and reference Figure 2 throughout the process:
1. Install the PLL software (see the PLL Software Installation
Guide)
2. Follow the hardware driver installation procedure (see the
PLL software Installation Guide for Windows XP only).
3. Connect the EVAL-SDP-CS1Z SDP-S board to the
EV-ADF5902SD1Z evaluation board.
4. Connect the 5 V power supply to the red and black banana
connectors of the EV-ADF5902SD1Z evaluation board.
5. Connect the USB cable from the EVAL-SDP-CS1Z SDP-S
board to the PC.
6. Connect an ac-coupled signal source analyzer to the
Transmitte r 2 J9 output SMA.
7. Run the PLL software.
8. Click the Select Device and Connection tab in the PLL
software window. Select SDP board (black), the ADF5902
device, and click Connect (see Figure 3).
9. Click the ADF5902 Controls tab, and then click Initialize
ADF5902 in the bottom right corner of the window (see
Figure 4).
10. Measure the TXOUT2 output signal on the J9 output SMA
using the spectrum analyzer.
POWER SUPPLY
SPECTRUM
ANALYZER
PC
SDP-S
ADAPTOR
BOARD
BLOCKING
CAPACITOR
+5V
17208-005
Figure 2. Typical EV-ADF5902SD1Z Evaluation Board Setup
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 6 of 16
EVALUATION BOARD SOFTWARE
ADF5902 CONTROLS
Click the ADF5902 Controls tab in the PLL software window
(see Figure 4) to select the user configurable register settings.
Consult the register descriptions of the ADF5902 data sheet for
details. Default settings are recommended for most registers.
After powering up the board, click the Initialize ADF5902 box
in the bottom right of the PLL software window to perform the
initialization sequence (as described in the ADF5902 data
sheet). Following this sequence, the ADF5902 transmitter
powers up and all ADF5902 blocks calibrate.
The ADF5902 Controls tab allows access to the PLL Setup tab
and the Ramp Generation tab.
PLL SETUP
To configure the PLL functionality of the ADF5902, take the
following steps:
1. In the PLL Setup tab (see Figure 4), set the reference
frequency (RF) settings for the PLL in the RF Settings
section, and the required settings for the TX2, TX1, and
LO outputs in the Register 0 section.
2. In the RF Settings section, type the reference frequency
in the Reference Frequency box. The PFD frequency
is calculated from the Reference Frequency value, the
R counter value, the Ref Doubler (reference doubler
option), and the Ref/2 (reference divided by 2 option).
3. Ensure that the value in the PFD Frequency box matches
the value specified when designing the loop filter for the
ADF5902.
4. Program the charge pump setting in the Register 12
section to match the loop filter design by clicking the
Charge Pump Setting dropdown menu and selecting a
value.
5. Click the Muxout dropdown menu in the Register 3
section, and then select the signal connected to the output
of the MUXOUT pin.
To pro g ram any of the ADF5902 registers, click the button
under each register value in the Registers section at the bottom
of Figure 4 to write that value to the device. For example, to
write the value for Register R0, click the Write R0 button.
A green background of a register value indicates that the
register value has changed in the PLL Setup tab, and that a
write of this register to the device is required.
17208-003
Figure 4. PLL Software Window Display, ADF5902 Controls
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 7 of 16
RAMP GENERATION
To configure the ramp functionality of the ADF5902,
1. Click the Ramp Generation tab in the PLL software
window (see Figure 5).
2. Select the ramp type from the Ramp mode dropdown
menu in the Modulation Type section, and set the various
ramp parameters in the CLK1, Slope 0, Slope 1, Slope 2,
Slope 3, and Timing Parameters sections.
Figure 5 shows an example of the ramping settings for
a continuous triangular ramp of 144 ramp steps over
200 MHz at the ADF5902 transceiver output, with a ramp
time of 5 ms. For 200 MHz, the PLL is programmed for a
100 MHz ramp because the feedback to the PLL is divided
by two.
3. After each parameter is set in the PLL software, write it to the
device by clicking the corresponding register write button.
17208-004
Figure 5. PLL Software Window Display, ADF5902 Ramps Generation
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 8 of 16
EVALUATION BOARD SCHEMATICS AND ARTWORK
ADF5902
TX OUTPUTS
SPI SIGNALS
REFERENCE LO OUTPUT
SDP
POWER MANAGEMENT
LOOP FILTER
DNI
DNI
DNI
DNI
DNI
142-0701-851
571-0500
571-0100
0
DNI
DNI
TBD0603
DNI
02K243-40M
02K243-40M
0
0
0
0
142-0701-851
TBD1206
TBD0603
02K243-40M
TP3 TP21
R1
J8
J9
J4
R10
R9
R8
C37
C33
J7
TP24
TP22
TP23
TP20
C42
TP18
R3
P2
P3
J1
TP17TP16
CPOUT
SPI_MISO
SPI_CLK
TX_DATA
DATA_TX TX_OUT1
LO
MUX_TX
DOUT_TX
CPOUT
VTUNE
REFIN
REFIN
AVDD_TX
SPI_MOSI
SPI_MOSI
CE_TX
LE_TX
DATA_TX
CLK_TX
REF_IN
VSUPPLY
AGND
AVDD_PLL
AVDD_PLL
AVDD_TX
VTUNE
LO
TX_OUT1
ATEST_TX
AVDD_TX
SPI_MISO
DOUT_TX
SPI_CLK
TX_OUT2
CLK_TX
LE_TX
TX_DATA
CE_TX
AGND
TX_OUT2
1
1
1
11
AGND
AGND
AGND
AGND
ADF5902_TX
TX_AHI
VCO_AHI
CP_AHI
CPOUT
REFIN
AHI
MUXOUT
TXOUT2
TXOUT1
TX_DATA
CE
CLK
DATA
LE
VTUNE
DOUT
ATEST
LOOUT
AGND
LFP VTUNECPOUT
POWER
VSUPPLY AVDD_TX
AVDD_PLL
REF_CLK
REFIN REF
AVDD
AGND
SPI_CON
SPI_CLK
SPI_MOSI
SPI_MISO
GPIO0
AVDD_TX
LE_TX
DATA_TX
CLK_TX
TX_DATA
DOUT_TX
CE_TX
GPIO5
GPIO4
GPIO3
GPIO2
SDP
GPIO7
GPIO6
GPIO5
GPIO4
GPIO3
GPIO2
GPIO1
GPIO0
SPI_CLK
SPI_MISO
SPI_MOSI
AGND
AGND
17208-006
Figure 6. EV-ADF5902SD1Z Evaluation Board Schematic (Page 1)
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 9 of 16
EEPROM
FX8-120S-SV(21)FX8-120S-SV(21)
24LC32A-I/MS
TBD0603 DNI
100K
100K
R36
R35
J5
U3
R6
J5
VIO
GPIO2
GPIO6
SPI_MOSI
SPI_MISO
SPI_CLK
GPIO1
GPIO3
GPIO5
GPIO7
GPIO0
GPIO4
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
7
4
8
5
6
3
2
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AGND
AGND
AGND
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
VSS
VCC
WP
A2
A1
A0
SCL SDA
17208-008
Figure 7. EV-ADF5902SD1Z Evaluation Board Schematic (Page 2)
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 10 of 16
DNI
DNI
0
0
330
330
330
330
0
330
DNI
10K
DNI
10K
DNI
10K
390
DNI
DNI
DNI
DNI
DNI
DNI
10K
DNI
DNI
DNI
DNI
TP9
R56
TP15
R55
TP14
TP10
TP13
TP11
TP12
TP1
TP7
TP6
R50
R54 R53 R52
R49
R48
R47
R46
R14
R38
R51
CLK_TX
DATA_TX
LE_TX
CE_TX
GPIO4
GPIO5
DOUT_TX SPI_MISO
SPI_MOSISPI_MOSI
GPIO0
AVDD_TX
GPIO2
GPIO3
SPI_CLK
TX_DATA
SPI_CLK
IN
IN
IN OUT
IO
AGND
AGND
AGND
IN OUT
IN OUT
IN OUT
IN OUT
IN
IN
IN
OUT
AGND
17208-008
Figure 8. EV-ADF5902SD1Z Evaluation Board Schematic (Page 3)
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 11 of 16
470OHM
100MEGHZ
TBD0603 10K
DNI
91
0
0
DNI
22UF
10PF
Y1
TP36
R45
C41
C40 E1
R40
R43
R42 R41
REFIN
AVDD
REF
1
OUT
AGND
AGND
IO
IN
E_D
13
2
4
GND
VCC
OUT
17208-009
Figure 9. EV-ADF5902SD1Z Evaluation Board Schematic (Page 4)
0
0
0
DNI
DNI
0
1UF
1N4001G
MBR0520LT1G
1UF
ADP150AUJZ-3.3-R7
1UF
0
0
1UF
ADP7104ARDZ-3.3
TP34
TP32
R25
C34
C38
R29 R2
U4
D2
D1
R33
R27
R23
C32
C36
U6
AVDD_TX
AVDD_PLL
VSUPPLY
1
1
5
1
42
3
AC
AGND
AGND
OUT
OUT
IN
GNDNC
VOUT
EN
VIN
SENSE
PAD
VIN
PG
GND
EN
8
7
6
5
1
2
3
4
NC
GND
VOUT
17208-010
Figure 10. EV-ADF5902SD1Z Evaluation Board Schematic (Page 5)
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 13 of 16
ADF5902
DNIDNIDNI
1000PF
TBD0603
DNI
10PF
1000PF
0.1UF
0.1UF
1000PF
10PF
10PF
DNI
5.1K
TBD0402
TBD0402
TBD0402
0.047UF
0.1UF
0.22UF
0.22UF
10PF
0.1UF
1000PF
DNI
DNI
1000PF
1000PF
ADF5902
C127
C129
C131
U1
R21
C30
C25
C20
C27
C29
C31
C22
C24
C26
C15
C18
C21
TP31TP30TP29
R22
C2C1
C16
C23
C28
CP_AHITX_AHI
C1 VREGC2
AHI
TX_AHI
REFIN
VCO_AHI
AGND
TX_OUT1
AGND
AGND
TX_OUT2
AGND
ATEST
AGND
LO_OUT
AGND
AGND
AHI
AHI
AHI
VREG
TX_DATA
CE
CLK
DATA
LE
DOUT
MUXOUT
RSET
CP_AHI
CPOUT
VTUNE
VCO_AHI
C1
C2
AGND
29
18
30
7
2
19
5
4
26
14
15
25
11
23
13
12
10
8
6
3
1
PAD
17
24
22
28
27
21
20
32
31
9
16
1
11
AGND
IN
AGND
AGND
AGND
AGND AGND AGND
AGNDAGNDAGND
IN
IO
IO
IO
OUT
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
IN
IN
EPAD
C2
C1
VCO_AHI
VTUNE
CPOUT
CP_AHI
RSET
MUXOUT
DOUT
LE
DATA
CLK
CE
TX_DATA
VREG
DVDD
AHI
REFIN
RF_AHI
GND
GND
LOOUT
GND
ATEST
GND
TXOUT2
GND
TX_AHI
TX_AHI
GND
TXOUT1
GND
IN
IO
17208-0012
Figure 12. EV-ADF5902SD1Z Evaluation Board Schematic (Page 7)
EV-ADF5902SD1Z Evaluation Board User Guide UG-1432
Rev. 0 | Page 15 of 16
ORDERING INFORMATION
BILL OF MATERIALS
Table 1. Bill of Materials
Quantity Reference Designator Part Description Manufacturer Part Number
2 C1, C2 1 nF, 0603 capacitors Murata GRM1885C1H102JA01D
1 C12 220 pF, 0805 capacitor Phycomp (Yageo) CC0805JRNPO9BN221
4 C15, C22, C27, C127 100 nF, 0603 capacitors AVX 06035C104KAT2A
4 C18, C24, C29, C129 1 nF, 0402 capacitors MurataA GRM1555C1H102JA01
1 C13 3.3 nF, 0805 capacitor TDK C2012C0G1H332J
4 C21, C26, C31, C131 10 pF, 0402 capacitors Phycomp (Yageo) CC0402JRNP09BN100
1 C14 100 pF, 0805 capacitor Yageo CC0805FRNPO9BN101
1 C16 47 nF, 0402 capacitor AVX 0402YD473KAT2A
1 C23 220 nF, 0402 capacitor TDK C1005X5R0J224K
1
C28
220 nF, 0603 capacitor
Murata
GCM188R71H224KA64D
4 C32, C34, C36, C38 1 µF, 0805 capacitors Murata GRM21BR71H105KA12L
1 C40 22 µF, 0805 capacitor Taiyo Yuden LMK212BJ226MG-T
1 C41 10 pF, 0603 capacitor Murata GRM1885C1H100JA01D
1 D1 Diode, standard, 1 A, 50 V ON Semiconductor 1N4001G
1 D2 Diode, Schottky, 0.5 A, 20 V ON Semiconductor MBR0520LT1G
1 E1 Ferrite bead Wurth Elektronik 7427-92642
2 J1, J7 Connector PCB end launch jack Cinch 142-0701-851
3 J4, J8, J9 Connector PCB SMA right angle
jack
Rosenberger 02K243-40M
1 J5 Connector PCB vertical type
receptable SMD
Hirose FX8-120S-SV(21)
1 P2 Connector PCB single socket black Deltron 571-0100
1 P3 Connector PCB single socket red Deltron 571-0500
10 R1, R3, R8 to R10, R40, R45, R50, R55,
R56
0 Ω, 0603 resistors Multicomp MC0603WG00000T5E-TC
4 R46 to R49 330 Ω, 0603 resistors Multicomp MC 0.063W 0603 330R
1 R14 Do not install Do not install Do not install
1 R18 510 Ω, 0805 resistor Yageo RC0805JR-07510RL
1 R19 1 kΩ, 0805 resistor Panasonic ERJ-6ENF1001V
6 R2, R23, R25, R27, R29, R33 0 Ω, 0402 resistors Panasonic ERJ-2GE0R00X
1 R20 0 Ω, 0805 resistor Panasonic ERJ-6GEY0R00V
1 R22 5.1 kΩ, 0603 resistor BOURNS CR0603-FX-5101ELF
2 R35, R36 100 kΩ ,0603 resistors Panasonic ERJ-3EKF1003V
1 R41 10 kΩ, 0603 resistor Panasonic ERJ-3EKF1002V
1 R43 91 Ω, 0603 resistor Yageo 9C06031A91R0FKHFT
1 TP1 Yellow test point Keystone Electronics 5000
4 TP16, TP17, TP23, TP24 Red test point Keystone Electronics 5000
1
U1
ADF5902 24 GHz Tx MMIC
Analog Devices
ADF5902WWCPZ-U1
1 U3 IC 32 kB serial EEPROM Microchip 24LC32A-I/MS
1 U4 3.3 V complimentary metal-oxide
semiconductor (CMOS) linear
regulator
Analog Devices ADP150AUJZ-3.3-R7
1 U6 3.3 V CMOS linear regulator Analog Devices ADP7104ARDZ-3.3
1 Y1 100 MHz crystal clock oscillator Connor-Winfield CWX113-100.0M
3 C20, C25, C30 Do not install Not applicable Not applicable
1 C33 Do not install Not applicable Not applicable
2 C37, C42 Do not install Not applicable Not applicable
3
R6, R21, R42
Do not install
Not applicable
Not applicable
1 R38 Do not install Not applicable Not applicable
UG-1432 EV-ADF5902SD1Z Evaluation Board User Guide
Rev. 0 | Page 16 of 16
Quantity Reference Designator Part Description Manufacturer Part Number
4 R51 to R54 Do not install Not applicable Not applicable
20 TP3, TP6, TP7, TP9 to TP15, TP18, TP20
to TP22, TP29 to TP32, TP34, TP36
Do not install Not applicable Not applicable
2 SCREW1, SCREW2 Screw, cheese, nylon, M3×10,
PK100
Allthread Plastics
Limited
119030010
2 NUT1, NUT2 Nut and washer, nylon, M3, PK100 Duratool 119030011
RELATED LINKS
Resource Description
ADF5902 Product Page, 24 GHz VCO and PGA with 2-Channel PA Output
ADP7104 Product Page, 20 V, 500 mA, Low Noise, CMOS LDO
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2018 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG17208-0-12/18(0)
