REV, 7/3/03 rc ALL CENTERLINE DIMENSIONS ARE BASIC. | 2 1 DATE REV ECN APPD. BY 03-02-05 | AO - - ( .708 [17.98] ) ( 148 [3.76] ) 1-17-06 | Al 7435 JM 1.635 [16.13] MAX. TO HIGHEST POINT OF BEAM } +t = 2 J a [8 [16.66] =| \__ (4) roto [0.25] 3 = =~ MAX. a 2 aS | STEWART 8 e = = & = PATENTED + mot o 3 = 2 oo wo = f : | > 2 Ys oO | | a! ] ! ( 083 [2.12] ) | | | | L ~ j r Z| | TO HIGHEST 4 .000 [0.00] _ TOP OF PCB A | 450 [11. a POINT OF BEAM 040 [1.02] (2) | Ke SUGGESTED PANEL OPENING TO BOTTOM | | .275 [6.99] MAX. }+=-.545 [13.84] OF OPENING SSS SS NOTES: | Jb 1. CONNECTOR MATERIALS: = HOUSING: THERMOPLASTIC UL94 V-0 = CONTACTS/SHIELD: COPPER ALLOY zg SHIELD PLATING: NICKEL OR TIN Ss | 100 [2.54] (3) > CONTACT PLATING: SELECTIVE GOLD IN CONTACT AREA 3 ig } Lt-.050 [1.27] (7 mom SEE CHART FOR PART NUMBER = | * 050 [1.27] | peel kB > 050 [1. r | 2 2. FOR PRODUCT SPECIFICATION SEE PRO22-01 = 4 -_- pd 0.035 [0.89] +.003 [0.08] (8) J | | | 7 8 3. TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS. e ~ 006 [0.15] PIN #1 hel e-o--6- - i 4, THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE B | Z -$-6-g-_-_- iL USER THE ABILITY TO HAVE REASONABLE JACK/PANEL 2 6.085 [1.65] 4.003 [0.08] (2) T CLEARANCES, YET MAINTAIN GROUNDING CAPABILITY. = ~ iG : , . THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION S [4.006 [0.15]| BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF + + * i y C ) _ d | LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. de | = 4125 [518] (4) | i; | 8 #7128 [3.25] ! } 50 MICRO-INCHES [1.27um] SS64800-057F ~ 1G006 [0.15]| [0.1 5] .080 [2.03] } | = = 1 450 [1143-4 30 MICRO-INCHES [0.76um] SS64800-056F | | a = 1 99 }- .610 [15.49] CONTACT PLATING } r 8 PART NUMBER | | ~ P.C.B. RECOMMENDED HOLE LAYOUT IN MATING AREA 2 | SEEN FROM COMPONENT SIDE THIRD ANGLE PROJECTION = Bel Stewart Connector 11118 Susquehanna Trail South Glen Rock, PA 17327-9199 (717) 235-7512 Fox: (717) 235-7954 http: //www.stewartconnector.com DO NOT SCALE DRAWING DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE EIGHT CONTACT, EIGHT POSITION, SHIELDED JACK ENHANCED SHIELD DIMENSIONS: INCHES [METRIC] UNLESS OTHERWISE SPECIFIED TOLERANCES ARE +.005 [0.13] ANGLES ARE + 1 SHEET NO. 1 OF 1 THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF BEL STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, COPIED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONSENT OF BEL STEWART CONNECTOR. MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. THE SUBJECT DRN BY: RVO DATE 03-02-05 CKD BY: DHG DATE 03-02-05 APPO BY: RCC DATE 93-02-05 OWG NO. CT640146F REV. Ay | AutoCAD