54ABT377
54ABT377 Octal D-Type Flip-Flop with Clock Enable
Literature Number: SNOS045
54ABT377
Octal D-Type Flip-Flop with Clock Enable
General Description
The ’ABT377 has eight edge-triggered, D-type flip-flops with
individual D inputs and Q outputs. The common buffered
Clock (CP) input loads all flip-flops simultaneously, when the
Clock Enable (CE) is LOW.
The register is fully edge-triggered. The state of each D in-
put, one setup time before the LOW-to-HIGH clock transi-
tion, is transferred to the corresponding flip-flop’s Q output.
The CE input must be stable only one setup time prior to the
LOW-to-HIGH clock transition for predictable operation.
Features
nClock enable for address and data synchronization
applications
nEight edge-triggered D flip-flops
nBuffered common clock
nSee ’ABT273 for master reset version
nSee ’ABT373 for transparent latch version
nSee ’ABT374 for TRI-STATE®version
nOutput sink capability of 48 mA, source capability of
24 mA
nGuaranteed latchup protection
nHigh impedance glitch free bus loading during entire
power up and power down cycle
nNon-destructive hot insertion capability
nDisable time less than enable time to avoid bus
contention
nStandard Microcircuit Drawing (SMD) 5962-9314801
Ordering Code:
Military Package Package Description
Number
54ABT377J-QML J20A 20-Lead Ceramic Dual-In-Line
54ABT377W-QML W20A 20-Lead Cerpack
54ABT377E-QML E20A 20-Lead Ceramic Leadless Chip Carrier, Type C
Connection Diagram
Pin
Names Description
D
0
–D
7
Data Inputs
CE Clock Enable (Active LOW)
CP Clock Pulse Input
Q
0
–Q
7
Data Outputs
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
Pin Assignment for
DIP and Cerpack
DS100216-1
Pin Assignment for LCC
DS100216-11
July 1998
54ABT377 Octal D-Type Flip-Flop with Clock Enable
© 1998 National Semiconductor Corporation DS100216 www.national.com
Truth Table
Mode Select-Function Table
Operating Mode Inputs Output
CP CE D
n
Q
n
Load “1” I h H
Load “0” I I L
Hold h X No Change
(Do Nothing) X H X No Change
H=HIGH Voltage Level
h=HIGH Voltage Level one setup time prior to the LOW-to-HIGH Clock Transition
L=LOW Voltage Level
I=LOW Voltage Level one setup time prior to the LOW-to-HIGH Clock Transition
X=Immaterial
=LOW-to-HIGH Clock Transition
Logic Diagram
DS100216-3
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
www.national.com 2
Absolute Maximum Ratings (Note 1)
Storage Temperature −65˚C to +150˚C
Ambient Temperature under Bias −55˚C to +125˚C
Junction Temperature under Bias
Ceramic −55˚C to +175˚C
V
CC
Pin Potential to
Ground Pin −0.5V to +7.0V
Input Voltage (Note 2) −0.5V to +7.0V
Input Current (Note 2) −30 mA to +5.0 mA
Voltage Applied to Any Output
in the Disabled or
Power-Off State −0.5V to +4.75V
in the HIGH State −0.5V to V
CC
Current Applied to Output
in LOW State (Max) Twice the rated I
OL
(mA)
DC Latchup Source Current −500 mA
(Across Comm Operating Range)
Over Voltage Latchup V
CC
+ 4.5V
Recommended Operating
Conditions
Free Air Ambient Temperature
Military −55˚C to +125˚C
Supply Voltage
Military +4.5V to +5.5V
Minimum Input Edge Rate (V/t)
Data Input 50 mV/ns
Enable Input 20 mV/ns
DC Electrical Characteristics
Symbol Parameter ABT377 Units V
CC
Conditions
Min Typ Max
V
IH
Input HIGH Voltage 2.0 V Recognized HIGH Signal
V
IL
Input LOW Voltage 0.8 V Recognized LOW Signal
V
CD
Input Clamp Diode Voltage −1.2 V Min I
IN
=−18 mA
V
OH
Output HIGH Voltage 54ABT 2.5 V Min I
OH
=−3 mA
54ABT 2.0 I
OH
=−24 mA
V
OL
Output LOW Voltage 54ABT 0.55 V Min I
OL
=48 mA
I
IH
Input HIGH Current 5 µA Max V
IN
=2.7V (Note 4)
5V
IN
=V
CC
I
BVI
Input HIGH Current 7 µA Max V
IN
=7.0V
Breakdown Test
I
IL
Input LOW Current −5 µA Max V
IN
=0.5V (Note 4)
−5 V
IN
=0.0V
V
ID
Input Leakage Test 4.75 V 0.0 I
ID
=1.9 µA
All Other Pins Grounded
I
OS
Output Short-Circuit Current −100 −275 mA Max V
OUT
=0.0V
I
CEX
Output High Leakage Current 50 µA Max V
OUT
=V
CC
I
CCH
Power Supply Current 50 µA Max All Outputs HIGH
I
CCL
Power Supply Current 30 mA Max All Outputs LOW
I
CCT
Maximum I
CC
/Input Outputs Enabled V
I
=V
CC
2.1V
1.5 mA Max Data Input V
I
=V
CC
2.1V
All Others at V
CC
or GND
I
CCD
Dynamic I
CC
No Load 0.3 mA/ Max Outputs Open (Note 3)
MHz One bit Toggling, 50%Duty Cycle
Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions
is not implied.
Note 2: Either voltage limit or current limit is sufficient to protect inputs.
Note 3: For 8 bits toggling, ICCD <0.5 mA/MHz.
Note 4: Guaranteed but not tested.
3 www.national.com
AC Electrical Characteristics
Symbol Parameter 54ABT Units
T
A
=−55˚C to +125˚C
V
CC
=4.5V to 5.5V
C
L
=50 pF
Min Max
f
max
Max Clock 150 MHz
Frequency
t
PLH
Propagation Delay 2.2 6.0 ns
t
PHL
CP to O
n
2.8 6.8
AC Operating Requirements
54ABT
T
A
=−55˚C to +125˚C
Symbol Parameter V
CC
=4.5V to 5.5V Units
C
L
=50 pF
Min Max
t
s
(H) Setup Time, HIGH 2.0 ns
t
s
(L) or LOW D
n
to CP 2.0
t
h
(H) Hold Time, HIGH 1.8 ns
t
h
(L) or LOW D
n
to CP 1.8
t
s
(H) Setup Time, HIGH 3.0 ns
t
s
(L) or LOW CE to CP 3.0
t
h
(H) Hold Time, HIGH 1.0 ns
t
h
(L) or LOW CE to CP 1.0
t
w
(H) Pulse Width, CP, 3.3 ns
t
w
(L) HIGH or LOW 3.3
Capacitance
Symbol Parameter Typ Units Conditions
C
IN
Input Capacitance 5 pF V
CC
=0V, T
A
=25˚C
C
OUT
(Note 5) Output Capacitance 9 pF V
CC
=5.0V
Note 5: COUT is measured at frequency f =1 MHz, per MIL-STD-883B, Method 3012.
www.national.com 4
AC Loading
Input Pulse Requirements
DS100216-4
*Includes jig and probe capacitance
FIGURE 1. Standard AC Test Load
DS100216-6
FIGURE 2. V
M
=1.5V
Amplitude Rep. Rate t
w
t
r
t
f
3.0V 1 MHz 500 ns 2.5 ns 2.5 ns
FIGURE 3. Test Input Signal Requirements
DS100216-8
FIGURE 4. Propagation Delay Waveforms for
Inverting and Non-Inverting Functions
DS100216-5
FIGURE 5. Propagation Delay,
Pulse Width Waveforms
DS100216-9
FIGURE 6. Setup Time, Hold Time
and Recovery Time Waveforms
5 www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
20-Lead Ceramic Chip Carrier
NS Package Number E20A
www.national.com 6
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
20-Lead Ceramic Dual-In-Line Package
NS Package Number J20A
20-Lead Ceramic Flatpack
NS Package Number W20A
7 www.national.com
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-
CONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or sys-
tems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose fail-
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
www.national.com
National Semiconductor
Europe Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5620-6175
Fax: 81-3-5620-6179
54ABT377 Octal D-Type Flip-Flop with Clock Enable
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated