This manual contains notices which you should observe to ensure your own personal safety,
as well as to protect the product and connected equipment. These notices are highlighted in
the
manual by a warning triangle and are marked as follows according to the level of danger:
!Warning
indicates
that death, severe personal injury or substantial property damage
can
result if proper
precautions are not taken.
!Caution
indicates
that minor personal injury or property damage can result if proper
precautions are not
taken.
Note
draws
your attention to particularly important information on the product, handling the product,
or to a particular part of the documentation.
Equipment may be commissioned and operated only by qualified personnel. Qualified per-
sonnel
within the meaning of the safety notices in this manual are persons who are authorized
to commission, ground and identify equipment, systems and circuits in accordance with
safety engineering standards.
Note the following:
!Warning
The equipment may be used only for the applications stipulated in the catalog and in the
technical
description and only in conjunction with
other equipment and components recom
-
mended or approved by Siemens.
Startup
must not take place until it is established that the machine, which is to accommodate
this component, is in conformity with the guideline 89/392/EEC.
Faultless and safe operation of the product presupposes proper transportation, proper stor-
age, erection and installation as well as careful operation and maintenance.
SIMATIC
is a registered trademark of Siemens AG.
Some of the other designations used in these documents are also registered trademarks; the
owner’s rights may be violated if they are used be third parties for their own purposes.
Editor and Publisher: AUT 91
We
have checked the contents of this manual for agreement with
the
hardware
and software described. Since deviations cannot be pre
-
cluded
entirely
, we cannot guarantee full agreement. However
, the
data
in this manual
are reviewed regularly and any necessary cor
-
rections
included in subsequent editions. Suggestions for improve
-
ment
are welcomed.
T
echnical data subject to change.
Siemens
AG 1997
Disclaimer of Liability
Copyright
Siemens
AG 1997 All rights reserved
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenders will be liable for damages. All rights, including rights
created
by patent grant
or registration of a utility model or design, are
reserved.
Siemens
AG,
Bereich Automatisierungstechnik,
Bedienen und Beobachten
Postfach 4848,
D-90327 Nuernberg
Siemens Aktiengesellschaft
Order No. 6A
V3991–1AE00–0AX0
Safety
Guidelines
Qualified Personnel
Correct Usage
Trademarks
Impressum
i
TD17
Equipment Manual
Edition 06/97
Preface
This
equipment manual provides operators, fitters, configurers and supervisors
with information on functionality and the technical design of the TD17 text
display.
The manual is part of the SIMATIC HMI documentation. The documentation
includes the manuals for the configuration software, operator panels or text
displays and communication between the PLC and the OP or TD.
Below
, you will find an overview diagram and a description of when you re
-
quire the dif
ferent manuals.
Configuration
Installation
Operation
Connection
PC
OP or TD
PLC
ProTool
User’s
Guide
ProTool/Lite
User’s
Guide
Online
Help
Graphics
Displays
Equipment
Manuals
Text-Based
Displays
Equipment
Manuals
Communi-
cation
User’s
Guide Other
PLCs
Purpose
How it fits in
ii TD17
Equipment Manual
Edition 06/97
Documentation target
Gr
oup Contents
Getting Started
Product Brief
Beginners
This documentation guides you step by step
through the configuration of
a screen containing static text
a screen containing an input/output field and
a bar graph
changing from one screen to another
a message.
This documentation is available for
–
OP3, OP5, OP15,
–
OP7, OP17 and
–
OP25, OP35, OP37.
ProT
ool
User’
s Guide
Configurer
Provides information for working with the
ProT
ool configuration software.
It contains
basic rules for configuration
a detailed description of objects and
functions that you can configure
examples of configuring objects.
This document is valid for OPs having
graphics displays.
ProTool/Lite
User’
s Guide
Configurer
Same contents as the ProT
ool User
’
s Guide.
This document is valid for TDs and OPs
having text-based displays.
ProTool
Online Help
Configurer
Provides information on your computer (PU or
PC) screen for working with the ProT
ool
configuration software. The online Help is
context-sensitive and contains
a general description of the editor to be
found in ProT
ool
a detailed description of the dif
ferent fields
in the dialog boxes
a comprehensive description of functions.
Application Example
Commissioning
Instructions
Beginners
Example configurations are supplied with
ProT
ool together with the associated PLC pro
-
grams. This document describes
how you load examples onto the TD or OP
and the PLC
how you can run the examples and
how you can upgrade the connection for
your application.
Preface
iii
TD17
Equipment Manual
Edition 06/97
Contentstarget
Gr
oupDocumentation
TP37
Equipment Manual
OP37
Equipment Manual
OP25, OP35, OP45
Equipment Manual
OP7, OP17
Equipment Manual
OP5, OP15
Equipment Manual
TD 17 Equipment Manual
Commissioning
engineers, users
Describes the OP hardware and general
operation. It contains
installation and commissioning
a description of the TD or OP device
electrical connection with connection of
the PLC, printer and configuration com
-
puter
TD or OP modes
TD or OP operation
description of the standard screens supplied
with the software and their usage
how to install options
maintenance and replacement of spare parts
OP3
Equipment Manual
Commissioning
engineers, users,
programmers
Describes the OP hardware, general operation
and the connection to a SIMA
TIC S7.
Communication
User’
s Guide
Programmers
Provides information on connecting TDs
and OPs to the following PLCs:
SIMA
TIC S5
SIMA
TIC S7
SIMA
TIC 500/505
drivers for other PLCs.
This document describes
the configuration and parameters required to
connect the TD or OP to the PLC and to the
network
the user data areas used for exchanging data
between OP and the PLC
Other PLCs
Online Help
Programmers
Provides information on connecting TDs or
OPs to PLCs such as:
Mitsubishi
Allen Bradley
Telemecanique
The drivers for connections to these PLCs are
located on separate floppy disks and are
referred to as NA
TIVE drivers. Installation of a
driver also installs the associated online Help.
Preface
iv TD17
Equipment Manual
Edition 06/97
Chapters Contents
1
- 2
Overview of the TD17 and its range of functions in tabular
form.
Y
ou should read this chapter before using individual
functions.
3 - 5
Step-by-step instructions on how to operate the TD17 using
standard screens.
6 - 7
–
Mechanical and electrical installation
– Commissioning
8
Detailed information on the TD17, its options and its
maintenance.
This part is primarily intended for installation and
commissioning personnel.
Appendices –
System messages
–T
echnical data
The following conventions are used in this manual:
Motor off Text
on the display of the TD is shown in ”type
-
writer style”.
Variable
Symbolic names representing variable values on the
display are shown in italic ”typewriter style”.
System
Standard screens that you can select are shown in
normal italics.
ESC
The names of buttons are shown in a dif
ferent type
-
face.
How the Manual is
organized
Conventions
Preface
v
TD17
Equipment Manual
Edition 06/97
For
technical questions, get in touch with your local Siemens representative
and branch. Y
ou will find the addresses at the end of this manual.
In addition, you can reach us by:
Telephone +49-91
1 895-7000 (Help Desk)
Fax +49-91
1 895-7001 (Hot Fax)
Internet
Current
information: http://www.aut.siemens.de/
TD/TP/OP
Home Page:
http://www.aut.siemens.de/hmi/html_00/opmar.htm
Mailbox (BBS)
1) +49-91
1 895-7100 (SIMATIC Customer Support)
CompuServe
go: sieaut
E-Mail
Internet
CompuServe
MS-Mail
simatic.support@nbgm.siemens.de
simatic support 101640,704
Hotline_Simatic#Tel7000
1)
For connecting to our BBS, use a modem of not more than 28,800 Bd. Set
the following parameters: 8, N, 1, ANSI or connect via ISDN.
The abbreviations used in the TD17 Equipment Manual have the following
meanings:
AS 51
1
Driver at PU interface to the SIMA
TIC S5
EM
Event Message
CPU
Central Processing Unit
EEPROM
Electrically erasable/programmable read-only memory
FB
Function block
HMI
Human Machine Interface
IF
Interface ID
LED
Light Emitting Diode
LCD
Liquid Crystal Display
MPI
Multipoint Interface
OP
Operator Panel
PLC
Programmable Logic Controller
PU
Programming Unit
PPI
Point-to-Point Interface
RAM
Random Access Memory
TD T
ext Display
Other support
Abbreviations
Preface
vi TD17
Equipment Manual
Edition 06/97
Preface
i
TD17 Equipment Manual
Edition 06/97
Contents
1 Product
Description
1-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Configuration
and Process Control Phases
1-1.
. . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Functions of a T
ext Display
1-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Design
of the TD17
1-4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Functionality 2-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 General Operation 3-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Keyboard 3-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Information Text 3-2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Standard Functions 4-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Operating
Levels
4-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Password
protection
4-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 System
settings by standard screens
4-4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 Operating
the TD from the PLC
4-8.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Messages 5-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Event
messages
5-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 System
Messages
5-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Displaying
Messages
5-4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.1 Scrolling
in W
aiting Messages at Message Level
5-5.
. . . . . . . . . . . . . . . . . . . .
5.4 Message
Buf
fer 5-5.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.1 Event
Buf
fer 5-6.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.2 System
Message Buf
fer 5-6.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5 Deleting
Messages
5-7.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.1 Deleting
the Event Buf
fer by Means of Standard Screens
5-7.
. . . . . . . . . . . . .
5.5.2 Automatically
Deleting the Event Buf
fer upon Buf
fer Overflow
5-8.
. . . . . . . . .
5.5.3 Automatically
Deleting the System Message Buf
fer upon Buf
fer Overflow
5-8
6 Installation 6-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Mechanical
Installation
6-2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Electrical
Installation
6-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1 Connecting
the Power Supply
6-4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2 Connecting
a Configuration Computer
6-5.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3 Connecting
a PLC
6-6.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Interface
Assignment
6-8.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
TD17 Equipment Manual
Edition 06/97
7 Commissioning 7-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Commissioning
Guide
7-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Startup
Behavior
7-5.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3 Testing
the Configuration in Conjunction with the PLC
7-6.
. . . . . . . . . . . . . . .
7.4 Testing
Communication via the PROFIBUS-DP
7-6.
. . . . . . . . . . . . . . . . . . . . .
8 Device
Description
8-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Optional
Backup Battery
8-3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Maintenance 8-4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A System
Messages
A-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B Technical
Data
B-1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
1-1
TD17 Equipment Manual
Edition 06/97
Product Description
With
text display TD17, you can visualize the operating states, malfunctions
and current process values of a connected PLC.
The T
ext Display features a number of standard functions. The displays and
operation of the device can be optimized by the configurer to meet the re
-
quirements of the process.
The TD17 is suitable for installation in cabinets and consoles.
1.1 Configuration and Process Control Phases
Before
the TD17 can be commissioned, it has to be prepared for its job of
visualizing data from the PLC; in other words, it has to be configured. This
means that you have to create data areas in the PLC memory in your configu
-
ration which can be used by the TD to communicate with the PLC.
The configuration for your TD17 is created on a computer (PC or PU) using
the ProT
ool configuration software under Microsoft
R
W
indowsT
. Once the
configuration is ready
, it is downloaded to the TD. For this you have to con
-
nect your computer to the TD. After the configuration has been downloaded,
you have to connect the TD to the PLC.
The TD now communicates with the PLC and reacts to program flows on the
PLC on the basis of the configured requirements.
Applications of
TD17
Creating data
areas
Configuring with
ProTool
1
1-2 TD17
Equipment Manual
Edition 06/97
Figure
1-1 outlines the configuration and process control phases.
Figure 1-1 Configuration and Process Control Phase
Text
which is required to be displayed on the TD17 has first to be created on
the PC or PU with ProT
ool and then downloaded to the T
ext Display
. If, for
example, the text you wish to display has to consist of static and variable
components, the variables have to be configured and the static text for ex
-
plaining the variables has to be entered – for example:
Temperature
Variable1
C of Furnace1
where
Temperature C of Furnace1
is the static text and
Variable1
is the variable that is read from the memory area of the PLC.
Y
ou will find information on configuring the TD in the
ProT
ool/Lite User
’s
Guide
. The
Communication User
’
s Guide
provides information on connecting
the TD to the PLC.
Static
and variable
text components
Further
information
Product Description
1-3
TD17
Equipment Manual
Edition 06/97
1.2 Functions of a Text Display
The
basic function of a T
ext Display consists in displaying process states.
The following display functions can be configured for the TD17:
event messages
information text
languages.
Event messages are information and operating notes on current machine or
process states. Event messages may contain process values. Process values
are displayed either numerically – for example,
Motor running at 3000 revs.
or
symbolically – for example,
Motor running normally,
where
a specific control value is assigned to
normally.
Y
ou classify a message as an event message when you are configuring.
Information text is additional information and hints on operation referring to
the current display
. This means that additional information can be displayed
when an event message is issued.
Message text, information text and system messages may be displayed in
several languages. Up to three of the following languages can be loaded si
-
multaneously on the TD17 and selected in online mode by the operator:
German
English
French
Italian
Spanish and
Russian (Cyrillic characters).
Display functions
Event messages
Information text
Languages
Product Description
1-4 TD17
Equipment Manual
Edition 06/97
1.3 Design of the TD17
The
TD17 has a plastic housing with a touch-sensitive front and is thus suit
-
able for ungrounded installation. The coloring of the universal front foil com
-
plies with machinery directive EN 60204. Figure 1-2 shows the design of the
TD17.
HELP
ESC
SIMA
TIC TD17
Display
System
keyboard
Interface connections
ENTER
Figure 1-2 Design of the TD17
High-contrast
LC display with LED back lighting. The following displays
can be configured:
4 lines of 20 characters; 1
1 mm character height or
8 lines of 40 characters; 6 mm character height or
7 keys for calling universal standard functions by means of standard screens
stored in the firmware.
The TD17 works without a battery and is thus maintenance-free. Operating
data are retained in a non-volatile state in the flash memory on the TD. The
internal hardware clock has reserve power for several days after the power is
turned of
f.
The TD17 can be upgraded with an optional lithium battery to back up the
message buf
fer and the hardware clock (longer than the reserve power). The
battery is not supplied with the TD.
1 x RS232/TTY for connecting to the PLC or computer
1 x RS422/485 for connecting to the PLC or computer
.
Maintenance-free electronic fuse.
TD17
versions
LC display
System keyboard
Data buffer
Interfaces
Fuse
Product Description
2-1
TD17
Equipment Manual
Edition 06/97
Functionality
Table
2-1 provides an overview of the functions of the TD17.
Table 2-1 Functionality of TD17
Function TD17
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Display
– Technology
– Configurable lines x characters per line/
character height
– Contrast adjustment
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
LCD
4x20/11 mm
8x40/6 mm
x
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Event messages
– Maximum number
– Maximum length (characters)
– Maximum number of entries in
event buffer
– View event buffer
– Delete event buffer
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
999
80
256
x
x
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Message acquisition
– In buffer with date, time and status
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
x
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Actual value display (numerical and symbolic)
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
x
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Information text
– Maximum length (characters)
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
320
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Configurable OP languages
German, English, French, Italian,
Spanish, Russian (Cyrillic characters)
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
x
Overview
2
2-2 TD17
Equipment Manual
Edition 06/97
Table 2-1 Functionality of TD17, continued
TD17Function
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Online languages (switchable)
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
3
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Communication with
SIMATIC S5 using
– AS511
–FAP
– PROFIBUS-DP up to 1.5 MBd
– PROFIBUS-DP up to 12 MBd
SIMATIC S7/M7 using
– PPI
– MPI
– PROFIBUS-DP up to 1.5 MBd
– PROFIBUS-DP up to 12 MBd
SIMATIC 500/505
– NITP
Loadable NATIVE drivers for
– Allen Bradley (DF1)
– AEG/Modicon (Modbus)
– Telemecanique (Adjust and Uni-Telway)
– Mitsubishi (FX)
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
x
x
x
x
x
x
x
x
x
x
x
x
x
Functionalit
y
3-1
TD17 Equipment Manual
Edition 06/97
General Operation
3.1 Keyboard
The
TD17 is operated by means of the keyboard. The keyboard consists of
seven system keys.
Key Function Purpose
HELP
Display informa
-
tion text (Help)
Y
ou can view information text configured for a message
by pressing HELP
.
ENTER
Select, confirm
(Enter)
Selects items from standard screens, confirms a selec
-
tion of symbolic values on standard screens.
ESC Escape
ESC has the following functions:
Hide system message
Cancels display of a non-serious system message.
Cancel information text display
Cancels display of information text to revert to the
previous display
.
Reset scr
olling in messages
Cancels scrolling in queuing messages to reset the
display to the current message.
Cancel Download mode
Cancels Download mode provided data are not cur
-
rently being downloaded to the TD. The TD ac
-
knowledges cancellation by issuing a system mes
-
sage.
Move cursor
Depending on the operating situation, the cursor is
moved one character or field at a time to the left, right,
up or down.
System
keys
3
3-2 TD17
Equipment Manual
Edition 06/97
Note
Pressing
several keys simultaneously may result in incorrect entries.
Keys Function
ESC
Overall r
eset
This key combination deletes the configuration
memory when the TD’
s power supply is turned on.
3.2 Information Text
Information
text provides information, for example, on what action to take
when a particular event message is displayed.
It is created at the time of configuring with ProT
ool and provides additional
information on the language set on the TD. Information text may be config
-
ured for event messages.
Configured information text can be read out by pressing
HELP
on the TD. In
-
formation text is shown for the topmost event message on the display
.
Y
ou can use the following keys to scroll in information text:
Scroll within information text.
ESC
Cancel information text display
. The former display
contents are shown once more.
Key combinations
Purpose
Calling
information text
Scrolling in
information text
General Operation
4-1
TD17
Equipment Manual
Edition 06/97
Standard Functions
After
the operating voltage has been turned on, a configuration has to be
loaded onto the TD so that it can be operated. The TD remains in Download
mode until a configuration is loaded.
The TD17’
s firmware contains a number of standard screens. Y
ou use these
standard screens to select all the functions necessary for operating the TD.
The individual functions are described in this manual by means of the stan
-
dard screens.
4.1 Operating Levels
When
operating the TD, you have to distinguish between two dif
ferent oper
-
ating levels, it being possible to switch from one to the other
.
Message level
:
The message level is the highest level on the TD. All waiting event mes
-
sages and system messages are displayed at message level. Following
startup, the TD is always at message level.
Standard scr
een level
:
At standard screen level, functions are selected, processed and executed.
When you select standard screen level, the directory of the standard
screens appears from which you can branch to the dif
ferent standard
screens.
If a system message is queuing and the TD is at standard screen level, the TD
changes immediately to message level.
Loading
a
configuration
Using standard
screens
Message level and
standard screen
level
4
4-2 TD17
Equipment Manual
Edition 06/97
Changes
of operating level are performed either manually or automatically
by the TD (refer to Figure 4-1).
Operator
-initiated change:
Press the following key:
ENTER
to change from message level to standard screen level
ESC
to change from standard screen level to message level.
For
ced change to message level:
Y
ou exit from standard screen level automatically as soon as a system
message is waiting to be displayed. The TD then goes to message level.
T
o hide a system message, press
ESC .
Once the system message has been hidden, the TD17 reverts to the point
from which it previously went to message level.
ESC
ENTER
Figure 4-1 Changing between Message and Standard Screen Level
Changing
operating
levels
Standard Functions
4-3
TD17
Equipment Manual
Edition 06/97
4.2 Password protection
To
prevent the OP from being operated by unauthorized persons, there is a
feature for instituting access protection by way of the supervisor password.
This is possible for the standard screen functions
Delete event buf
fer
Language and
Mode Change.
The supervisor password is set during configuration. It consists of numeric
characters. The default settings is 100.
Use the keys listed below to enter a password.
Select numerals (0 to 9) for the password. For exam
-
ple, for the first character of password 100 select the
numeral 1.
Move to the next character of the password.
ENTER T
erminate password entry
.
Access protection
Supervisor
password
Entering a
password
Standard Functions
4-4 TD17
Equipment Manual
Edition 06/97
4.3 System settings by standard screens
In
standard screens, functions are implemented that are required to operate
the TD17. The dif
ferent functions in this manual are described with reference
to the standard screens.
The table provides an overview of the functions available on the dif
ferent
standard screens.
Standard Scr
een Function
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
Display event message buf
fer
(Section 5.4.1)
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Display event messages in event buffer
Display message text relating to a message
selected in the event buffer
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
Delete
event message buf
fer
(Section 5.5.1)
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Delete all event messages from the event
buf
fer that have arrived or departed
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
Display system message buf
fer
(Section 5.4.2)
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Display system messages contained in
system buf
fer
Display message text relating to a
message selected in the system
message buf
fer
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
Set language & contrast
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Select one of the three languages
contained in the configuration for the
TD
Adjust display contrast
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Set date & time
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Set date and time
ÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁ
Change modes
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
TD operating modes: Online, Of
fline,
Download
T
o use standard screen functions, change from message level to standard
screen level by pressing
ENTER
. You are then in the standard screens direc
-
tory.
Call a standard screen using the following keys:
Select a standard screen from the directory
.
ENTER
Call the standard screen you selected.
Standard
screens
Changing to
standard screen
level
Calling a standard
screen
Standard Functions
4-5
TD17
Equipment Manual
Edition 06/97
Messages
and information text can be displayed in several languages. Up to
three of the following languages can be loaded simultaneously on the TD and
selected in online mode by the operator:
Step Action
1
Select the standard screen called Set Language & Contrast
.
The standard screen is displayed.
Contrast: 2
Language: English
2
Using the arrow key
, go to the entry for the cur
-
rently selected language.
3
Chose the language you require using the arrow
keys.
The selection list contains only those languages
which have been loaded onto the TD.
4ENTER
Confirm your input.
The TD restarts and shows all the pieces of lan
-
guage-dependent text in the new language.
W
ith the TD17, you can change the contrast of the LC display by means of a
standard screen. Perform the following steps to do this:
Step Action
1
Select the standard screen called
Set Language/Contrast.
The standard screen is displayed.
Contrast: 2
Language: English
2
Select the contrast you require by means of the
arrow keys (range of values: 1 – 16).
3ENTER
Confirm your input.
4ESC
Exit from the standard screen.
Language setting
Adjusting contrast
Standard Functions
4-6 TD17
Equipment Manual
Edition 06/97
The
current date and time can be set on the TD in order
, for example to per
-
form a correction for summer or winter time. Any change af
fects all mes
-
sages in which a date/time variable is displayed. The display format for date
and time is set in the configuration and cannot be changed later on the TD.
Step Action
1
Select the standard screen called
Set Date & T
ime.
The standard screen is displayed.
Date: Fr 04.18.00 Time: 11:59:00
2
Go to the entry fields you require.
3
Set the date and time by means of the arrow keys.
4ENTER
Confirm your input.
5ESC
Exit from the standard screen.
Note
W
ithout a backup battery (optional upgrade), the TD17 continues to count
the date and time for several days following interruption of the power sup
-
ply
. If the TD17 is restarted subsequent to this stored ener
gy time, the inter
-
nal hardware clock has to be updated.
Setting date and
time
Standard Functions
4-7
TD17
Equipment Manual
Edition 06/97
The
following TD operating modes can be set by means of a standard screen:
Online
In Online mode, there is a logical connection between the TD and the
PLC or the TD attempts to establish a connection.
Offline
In Of
fline mode, there is no logical connection between the TD and the
PLC. Neither does the TD attempt to establish a connection. Y
ou can con
-
tinue to operate the TD .
Download
In Download mode, data are downloaded from the PU or PC to the TD. In
this mode there is no logical connection between the PLC and the TD.
Y
ou cannot operate the TD while downloading is in progress.
T
o set TD operating modes, perform the following steps:
Step Action
1
Select the standard screen called
Change modes
.
The standard screen is displayed.
Operating mode Online
2 Set
the operating mode by means of the arrow
keys.
3ENTER
Confirm your input.
4ESC
Exit from the standard screen.
Y
ou will find further information about TD operating modes in Chapter 7.
Mode setting
Standard Functions
4-8 TD17
Equipment Manual
Edition 06/97
4.4 Operating the TD from the PLC
The
TD and the user program communicate by alternately writing and read
-
ing data areas in the PLC’s memory
. This means that the PLC and the TD can
induce each other to perform dif
ferent actions by evaluating these user data
areas.
PLC jobs are functions triggered by the PLC on the TD – for example, trans
-
ferring date and time from the TD to the PLC. A job is stored together with
its job number and parameters on the PLC.
Y
ou will find a complete list of all PLC jobs and their parameters, together
with a description of all the user data areas you have to create on the PLC, in
the
Communication User
’
s Guide
.
One bit is permanently assigned to every key on the system keyboard in the
data area for system keyboard bits. The bit remains set over the period of
time the corresponding key is pressed. Releasing the key resets the bit.
By evaluating this data area, the operator
’
s attention can be drawn to incor
-
rect operation of a key by means of an error message, for instance.
T
ransfer of the time and date from the TD can be initiated by means of a
PLC job in order to synchronize the TD and the PLC.
Shared
data areas
PLC jobs
System keyboard
assignment
Date and time
Standard Functions
5-1
TD17
Equipment Manual
Edition 06/97
Messages
Messages
are used to display events and states in the control process on the
TD. A message consists of static text as a minimum. It may also contain vari
-
ables.
The following types of message are displayed on the TD:
event messages and
system messages.
Event messages are initiated by the PLC. They are configured and contain
process-related information.
Issued event messages are stored in a separate message buf
fer on the TD.
Messages contained in the buf
fer can be displayed.
System messages are initiated by the TD. They do not have to be configured.
System messages provide information on operating states of the TD and on
maloperations or malfunctions in communication.
5.1 Event messages
Event
messages are messages which draw attention to regular sequences of
events or states such as
Temperature reached
or
Motor running.
You
can configure hints on operation as event messages, in addition to status
messages of this kind. If, for example, the machine operator wishes to start
the filling operation but has for
gotten to open the water intake valve on the
mixer
, he can be prompted by a message such as
Open water intake valve
to
rectify the error
.
Message types
Event messages
System messages
Definition
5
5-2 TD17
Equipment Manual
Edition 06/97
Event
messages can be configured so that any of their text components flash
to distinguish them from the remaining message text.
Messages may contain static text or variable fields. The variable fields, for
example, display current PLC actual values in numerical or symbolic form.
In addition, the date and time can also be output in messages.
An event message consists of up to 80 characters.
If the condition is met in the current process for issuing a message – for ex
-
ample, a variable has been reached – a bit is set in the data area by the PLC
user program for event messages. The TD reads the data area after a config
-
ured polling time. In this way
, a message is detected as having ”arrived”. The
bit is reset by the PLC when the condition for issuing the message no longer
exists. The message is then regarded as having ”departed”.
Event messages are written to the event buf
fer on the TD upon arrival. The
following details are entered in the buf
fer in chronological order:
times of incidents
arrivals and departures of events
message numbers
values of variables at the time of arrival or departure.
The message buf
fer on the TD can store up to 256 events. Events are:
arrival of a message.
departure of a message.
During configuration, you can define a remaining buf
fer space. When this
remaining buf
fer space has been reached, an automatic overflow warning is
issued – for example
EM remaining buffer.
This
overflow warning is a system message. Messages continue to be entered
in the buf
fer even after the remaining buf
fer size has been reached.
A sub-category of the event message is the standby message. The standby
message is event message number 0. It appears on the display when the TD is
operating at message level and event messages are not waiting.
Presentation
Message bit
procedure
Event buffer
Overflow warning
Standby message
Messa
g
es
5-3
TD17
Equipment Manual
Edition 06/97
The
standby message is stored in the firmware and, by default, contains the
firmware version and the device type – for example
TD17 Vx.xx
4 x 20 char.
Figure 5-1 Example of Default Standby Message on TD17
Depending
on the configuration, the standby message can be represented by
other text – for example, a company logo. It may contain the date and time
but not variables.
5.2 System Messages
System
messages draw attention to internal operating states of the TD. For
example, they indicate maloperations or communication malfunctions. This
type of message has highest display priority
. If a relevant malfunction occurs
on the TD, the event message currently being displayed is hidden and a sys
-
tem message is issued in its place.
Once the system message has been hidden, the TD returns to the point from
which it branched.
System messages are classified as serious or non-serious system messages. A
serious system message is based on an error which can be eliminated only by
a cold or warm restart of the TD.
All other errors generate a non-serious system message – for example, the
remaining size of the event buf
fer has been reached.
The display of a message is terminated automatically if the configured dura
-
tion of display has expired. Alternately
, you can cancel the display of a mes
-
sage by pressing
ESC.
Y
ou will find a list of system messages and their explanations in Appendix A.
Definition
Serious and non-
serious system
messages
Messa
g
es
5-4 TD17
Equipment Manual
Edition 06/97
Display
of system messages (with the exception of internal errors 7xx) can be
inhibited at the configuration stage. System messages whose display has been
inhibited continue to be included in the system message buf
fer and thus can
be viewed on the display
.
The system message buf
fer can store up to 100 messages. System messages
are entered in the buf
fer with their message numbers and their arrival. Mes
-
sage departure is not recorded. Some minor errors and operating errors are
not logged in the system message buf
fer
, either
. Messages from the system
message buf
fer are displayed in the same order as they arrive.
5.3 Displaying Messages
Event
messages are always output to the TD at message level and are dis
-
played according to display and message priorities.
System messages always have top priorities in so far as display is concerned.
Depending on their importance, message priorities can be set within event
messages in the configuration as follows
1 (low) to
4 (high).
If several messages having the same display priority are waiting, they are
displayed according to their message priority – the highest first and the low
-
est last.
If several event messages and system messages having identical display and
message priorities are waiting simultaneously
, the most recent message is
displayed.
Inhibiting
system
messages
System message
buffer
Display
Display priorities
Message priority
First/last message
display
Messa
g
es
5-5
TD17
Equipment Manual
Edition 06/97
5.3.1 Scrolling in Waiting Messages at Message Level
If
there are no system messages waiting, you can scroll at message level
through the messages which have not yet departed. To do so, use the follow
-
ing keys:
Back to previous event message
Forward to more recent event message,
ESC
Back to current (most recent) message.
If the TD has not been operated for more than a minute, the current (most
recent) message is displayed again.
The event messages (EMs) illustrated below are waiting on the TD:
11:50 EM 02
12:08 EM 07
12:00 EM 04
Message
level
5.4 Message Buffer
Messages
displayed on the TD are written to the message buf
fer for event
messages. T
o view the message history, you can call the message buf
fer by
means of standard screens.
The data in the message buf
fers are lost when the TD17 is turned of
f or fol-
lowing an interruption of the power supply. If back-up is required, you must
connect an optionally available battery
.
Meaning of keys
Example
Purpose
Back-up time
Messa
g
es
5-6 TD17
Equipment Manual
Edition 06/97
5.4.1 Event Buffer
Select
the standard screen
Display event message buffer
. The messages stored
in the event buf
fer are shown on the display (Figure 5-2).
Message No: 045 A
on 12.09.96 10:23:50
Message No: 031 D
on 12.09.96 09:51:43
Figure 5-2 Display of Event Buffer (Example: 4x20 representation)
Explanation
of example display
(first message):
Message No. Message
number of the event message.
045
The displayed event message is number 045.
A
The message has arrived (D: departed).
on
date and time
Date
and time of arrival/departure of the event mes
-
sage.
Arr
ow keys
:
Display message text of selected event message.
Back to event message list.
and
Scroll in event message list.
5.4.2 System Message Buffer
Select
the standard screen
Display system message buffer
The messages stored in the buf
fer are shown on the display
. Operation and
display are the same as for the event buf
fer.
Viewing the event
buffer
Viewing the
system message
buffer
Messa
g
es
5-7
TD17
Equipment Manual
Edition 06/97
5.5 Deleting Messages
Event
messages are stored automatically in the event buf
fer
. Each of these
buf
fers can hold as many as 256 events. Event messages should be deleted
from the buf
fer to avoid buf
fer overflow
.
Messages from the event buf
fer are deleted
by means of a standard screen or
automatically upon buf
fer overflow
System messages are deleted automatically only upon buf
fer overflow
.
5.5.1 Deleting the Event Buffer by Means of Standard Screens
You
can delete all event messages by means of standard screens.
T
o delete, perform the following steps:
Step Action
1
Select the standard screen
Delete event message buffer
.
2 Press
if you wish to delete the buf
fer
if you do
not
wish to delete the buf
fer.
ESC
ENTER
3
Enter the password and press
ENTER
4
Exit from the standard screen by pressing
ESC
Avoiding buffer
overflow
Procedure
Messa
g
es
5-8 TD17
Equipment Manual
Edition 06/97
5.5.2 Automatically Deleting the Event Buffer upon Buffer Overflow
An
overflow warning is output to the display when the event buffer reaches
the configured remaining buffer size. If the event buf
fer cannot accept any
more messages, those which have already departed are the first to be deleted
automatically.
If the remaining buf
fer size is not freed by this action, as many as the oldest
event messages are deleted – irrespective of priority and message status (ar
-
rived, departed) – as are necessary to restore the remaining buffer size.
5.5.3 Automatically Deleting the System Message Buffer upon Buffer
Overflow
If
the system message buf
fer is completely full, the oldest message is deleted
automatically from the buf
fer when a new system messages is issued. There
is no overflow warning.
Remaining buffer
size and buffer
overflow
Procedure
Messa
g
es
6-1
TD17
Equipment Manual
Edition 06/97
Installation
The
TD17 is suitable for installation in cabinets and consoles.
The front
panel has to be provided with a mounting cutout for this purpose refer to
Chapter 8). The front panel must not be thicker than 6 mm. No other drilled
holes are required for mounting. Y
ou will find details about the mounting
depth in Chapter 8.
Make sure at the location where you plan to install the TD that there is a
clearance of at least at 50 mm beneath the housing of the TD for protruding
connectors.
!Caution
The TD must be brought to room temperature before it is commissioned.
In the event of moisture condensation, do not turn the TD on until it is
absolutely dry
.
The TP subjected to function testing before shipping. Should a fault oc
-
cur for all that, please enclose a full account of the fault when returning
the TD.
T
o prevent the TD from overheating in operation,
–
the device must not be exposed to direct sunlight (this simultaneously
prevents fading of the foil front),
–
the ventilation slits in the housing must remain free after installation.
On opening the panel, certain parts of the system become accessible that
may conduct hazardous voltage.
Note
The IP65 degree of protection on the front panel can be guaranteed only
when the gasket on the front panel of the TD fits properly
.
Installation
location and
conditions
6
6-2 TD17
Equipment Manual
Edition 06/97
6.1 Mechanical Installation
Step Action
1 Insert
the retaining hooks of the screw type clamps enclosed
with the TD into the corresponding recesses in the housing of the
TD.
Y
ou require five screw type clamps for the TD17.
2 T
ighten the TD from behind in the
front panel using a screw
-
driver
. Note:
–
Make sure the gasket fits properly on the front plate.
–A
void excessively high torques and thus prevent damage.
Front panel
TD17
Installing the TD
Installation
6-3
TD17
Equipment Manual
Edition 06/97
6.2 Electrical Installation
The
TD requires electrical connections
to the power supply
to the configuration computer (PU or PC)
to the PLC.
The electrical connection to the configuration computer is required only to
download the firmware and configuration to the TD.
The basis for interference-free operation is electromagnetic compatible hard
-
ware design of the PLC and the use of interference-proof cables.
The directives described in the “SIMA
TIC S5 Directives for the Interference-
Free Design and Installation of Programmable Logic Controllers” (Order No.
6ES5998-7AB1
1) apply to the interference-proof design and installation of
the TD.
!Caution
Use only shielded cables for all signal links.
Screw or lock all plug connections.
Do not install signal lines in the same cable ducts as power cables.
Electrical
connections
Electromagnetic
compatible design
Installation
6-4 TD17
Equipment Manual
Edition 06/97
6.2.1 Connecting the Power Supply
There
is a two-pin terminal block on the underside of the housing for con
-
necting the power supply. The terminal block is designed for cables having a
cross-section not lar
ger than 2.5 mm
2.
Figure 6-1 shows the position of the terminal block.
T
erminal block
Figure 6-1 Connecting the Power Supply (View of Underside of TD)
The
terminal screws are accessed by means of a hole drilled in the rear panel.
Access to
terminal screws
Chassis ground
Figure 6-2 Accessing Terminal Screws and Chassis Ground
Terminal block
Installation
6-5
TD17
Equipment Manual
Edition 06/97
!Caution
With
a 24 V supply
, make sure that the extra-low voltage is isolated sa
-
fely
. Use only power supplies complying with IEC 364-4-41 or
HD 384.04.41 (VDE 0100. Part 410) Usage
The supply voltage must be within the voltage range specified above. If
not, there may be functional failures on the TD.
Connect the chassis ground
on the rear panel of the TD to the cabinet
ground.
6.2.2 Connecting a Configuration Computer
Figure
6-3 shows you how to connect a configuration computer (PU or PC)
temporarily to the TD17 to download the firmware and the configuration
data. Standard cables are available for the connections shown (refer to the
ST80.1 catalog).
RS232
TTY
passive
TTY passive
RS232
TTY/RS232
converter
COM1/2
(25-pin)
COM1
(25-pin)
COM2
(9-pin)
PC
PG 7xx
TD17
IF1A
Figure 6-3 Connection Configuration Diagram for Configuration Computer
Chassis ground
Connection
configuration
diagram
Installation
6-6 TD17
Equipment Manual
Edition 06/97
6.2.3 Connecting a PLC
Figure
6-4 shows the basic options for connecting the TD to a PLC. For fur
-
ther details refer to T
able 8-1 in Chapter 8. Standard cables are available for
the connections shown (refer to the ST80.1 catalog).
TTY
active
RS232
TTY passive
PU interface
SI 2
RS232
(9/25-pin)
RS422 (9-pin)
SIMA
TIC S5
TTY active
CP523
TTY active
RS232
TTY/RS232
converter
COM1/2
(9/25-pin)
RS232
PLCs of other
manufactu-
rers
PU or
PC
RS422/RS485
RS422/RS485
CPU
SIMA
TIC 500/505
PROFIBUS-DP
SIMATIC
S7/M7
RS232/TTY
1) Any
PROFIBUS bus terminal (apart from FSK)
1)
CP521 SI
IF1A
IF1B
TD17
Figure 6-4 Connection Configuration Diagram for PLCs
Connection
configuration
diagram
Installation
6-7
TD17 Equipment Manual
Edition 06/97
You
can use the DIP switch at the rear of the TD17 to configure interface
IF1B.
DIP switch
Figure 6-5 DIP Switch of the IF1B Interface
This
involves changing over the RS422 receive data and the R
TS signal. By
default, the R
TS signal is not required by the communication peer
.
The table shows the permissible DIP switch settings.
Commun
i
cat
i
on
Sw
i
tch Sett
i
ng
C
ommun
i
ca
ti
on
S
w
it
c
h
S
e
tti
ng
TD17 PLC
RS422/RS485 ON
OFF
1234
TD17
PLC
PPI/MPI/PROFIBUS
RTS
on pin 4 (default)
ON
OFF
1234
RTS
on pin 9 (such as PU)
ON
OFF
1234
No RTS on the connector
ON
OFF
1234
TD17 PLC
PPI/MPI
Standard
cable
ON
OFF
1234
The
interface assignment of the TD will be found in Section 6.3 of this
manual.
Configuring
Interface
IF1B
Installation
6-8 TD17
Equipment Manual
Edition 06/97
6.3 Interface Assignment
The
following tables show the interface assignment of the TD17.
Table 6-1 IF1A Pin Assignment of the 15-pin Sub D Socket
Pin General RS232 TTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not assigned
Not assigned
GND
+5 V
GND
RxD
TxD
CTS
RTS
RxD–
TxD+
TxD–
RxD+
+20 mA
+20 mA
Table 6-2 IF1B: Pin Assignment of the 9-pin Sub-D Socket
Pin General PROFIBUS-DP RS422 RS485
1
2
3
4
5
6
7
8
9
Not
assigned
(GND)1)
GND (floating )
+5 V (floating )
(P24-In)1)
Data B
RTS2)
Data A
RTS2)
TxD (B)
RxD (B)
2)
TxD (A)
RxD (A)
2)
Data B
Data A
1) Reserved for future applications. From current-limited source < 1 A only
2) Can be switched by means of the DIP switch (for switch settings refer to Section 6.2.3)
Overview
Installation
81
15 9
51
96
7-1
TD17
Equipment Manual
Edition 06/97
Commissioning
Figure
7-1 shows the most important steps for initial startup, recommission
-
ing and normal operation of the TD. The commissioning guide which follows
explains the dif
ferent steps that have to be taken to commission the TD.
Download configuration data to the TD
COM1/2
Set Download mode by means of
Standard Screen
Change modes
T
urn on power supply of TD
Initial startup
Neither a configuration nor
firmware is available on the
TD.
Recommissioning
The TD already has a config
-
uration but it is required to
work with a modified or new
configuration.
Normal operation
The TD is operated with the
loaded configuration.
Standby message
TD
ProTool
Figure 7-1 Commissioning Flowchart
Flowchart
7
7-2 TD17
Equipment Manual
Edition 06/97
Before
commissioning the TD, take note of the following:
!Caution
W
ith the SIMA
TIC S5, compression of the internal program memory on
the PLC (PU “Compress” function, integrated FB COMPR) is not al
-
lowed when a TD is connected. Compression modifies the absolute ad
-
dresses of the blocks in the program memory
. As the TD reads the ad
-
dress list only during startup, it does not detect any address modifications
and accesses the wrong memory areas.
If compression is inevitable during routine operation, turn of
f the TD
prior to compression.
De-ener
gize theTD in hazardous areas before removing connectors.
Before
commissioning
Commissionin
g
7-3
TD17
Equipment Manual
Edition 06/97
7.1 Commissioning Guide
During
initial startup, you have to load the firmware required for operation
and the configuration onto the TD. Perform the following steps to do this:
Step Action
1
Connect the interface of the TD17 by means of a suitable standard
cable to the configuration computer (PU or PC).
2 T
urn on the power supply of the TD.
Since a configuration has yet to be loaded at this stage, the TD
automatically goes to Download mode, displaying the message
”Ready for Transfer”
and waits for the data to be transferred from the PC or PU.
Y
ou cannot operate the TD in this mode.
3
Start the download operation on the PC or PU to the TD.
The TD checks the connection to the PC or PU. If a connection is
not available or if it is not functioning properly
, the TD issues a
corresponding error message.
If the connection is in order, downloading of the configuration
from the PC or PU is initiated to the TD.
As long as data are not being downloaded to the TD, you can
cancel Download mode by pressing
ESC
Note
Refer to the
ProT
ool/Lite User
’
s Guide
for the settings required in ProT
ool
for the download operation.
Once the configuration has been successfully downloaded, the TD restarts.
The TD shows the standby message.
Initial startup
Commissionin
g
7-4 TD17
Equipment Manual
Edition 06/97
If
you wish to replace a configuration on the TD with another one, proceed as
follows:
Step Action
1
Connect interface IF1A by means of a suitable standard cable to
the Configuration computer (PU or PC).
2 T
urn on the power supply of the TD.
3
Call the standard screen
Changes modes
to transfer the TD to
Download mode.
If necessary
, enter the supervisor password beforehand.
The TD then changes, with the message
”Ready for Transfer”
to Download mode and waits for data to be downloaded from the
PC or PU.
ESC
4
Start the download operation on the PC or PU to the TD.
The TD checks the connection to the PC or PU. If a connection is
not available or if it is not functioning properly
, a corresponding
error message is issued on the PC or PU.
If the connection is in order, downloading of the configuration
from the PC or PU is initiated to the TD. The configuration resid
-
ing on the TD is overwritten by the new one during the download
operation.
Y
ou can cancel the download operation to the TD by
pressing ESC
Once the configuration has been successfully downloaded, the TD restarts.
The TD shows the standby message.
Any fault occurring during commissioning or in operation is normally dis
-
played on the TD by means of a system message.
The Appendix to this manual lists some of the most important system mes
-
sages with notes on troubleshooting.
Recommissioning
Fault diagnosis
Commissionin
g
7-5
TD17
Equipment Manual
Edition 06/97
7.2 Startup Behavior
ESC
No Yes
TD starts up
Self test
No configuration exists
or key combination
pressed?
After the power supply has been turned on, the TD performs a self
test. In the test, it checks the operability of the most important TP
components and displays the test results.
If there is not a configuration on the TD, the TD goes automati
-
cally to Download mode.
Download
operation
Initialization
Establish connection
to PLC
Standby message
The TD now performs various internal initializations.
In this phase of startup, the TD attempts to establish a connection
to the PLC.
If communication is not possible – for example, because the cable
to the PLC has not been inserted – the TD displays a system mes
-
sage.
After startup, the TD displays the standby message.
Commissionin
g
7-6 TD17
Equipment Manual
Edition 06/97
7.3 Testing the Configuration in Conjunction with the PLC
You
can test the TD17 in conjunction with the connected PLC in ONLINE
mode. In this way you check that the correct data areas have been configured.
Step Action
1
Connect the TD to the PLC.
2
A message on the TD indicates that it has been connected suc
-
cessfully.
3 Y
ou can now test all the items contained in your configuration
that are necessary for communication with the PLC. Depending
on the configuration, these might be:
event messages
area pointers.
7.4 Testing Communication via the PROFIBUS-DP
There
is a bus fault LED on the rear of the TD (Figure 7-2). When on, the
LED indicates that communication is in progress between the TD and the
PLC via the PROFIBUS-DP. A permanently dark LED indicates disrupted
communication.
The LED can be used to perform a rapid diagnosis of any problems that may
occur during communication.
Bus fault LED
Figure 7-2 Location of the Bus Fault LED at the Rear of the TD
Testing
with PLC
connected
Procedure
Bus fault LED
Commissionin
g
8-1
TD17
Equipment Manual
Edition 06/97
Device Description
This
chapter describes the dimension drawings and connection elements of
the TD17.
231
98
240
89
* Without cable lug under the bonding screw
The
TD17 requires a mounting cutout (WxH) of 231
+1
mm x 89
+1
mm.
In this chapter
Dimensions
Mounting cutout
8
8-2 TD17
Equipment Manual
Edition 06/97
The
TD17 features various communication options (refer to T
able 8-1). Fig
-
ure 8-1 shows the connection elements on the underside of the TD.
IF1B IF1A
Power
supply
connection
Backup battery
connection
Figure 8-1 Locations of the Connection Elements on the Underside of the TD17
Table 8-1 Communications Options Featured by the TD17
Connection Interface
SIMATIC
S5
– AS51
1 (TTY)
– F
AP (TTY/RS232)
– PROFIBUS-DP
IF1A
IF1A
IF1B
SIMA
TIC S7/M7
– PPI
– MPI
– PROFIBUS-DP
IF1B
IF1B
IF1B
SIMA
TIC 500/505
– RS232
– RS422/RS485
IF1A
IF1B
Other PLCs
– RS232/TTY
– RS422/RS485
IF1A
IF1B
PC/PG (TTY/RS232)
IF1A
Connection
elements
Device
Description
8-3
TD17
Equipment Manual
Edition 06/97
8.1 Optional Backup Battery
You
can upgrade the TD17 with an optional backup battery
. When the power
supply is interrupted, the backup battery ensures that
the operating data in the TD17 message buf
fer are retained and
the TD17 hardware clock continues top run on its internal reserve power
.
Y
ou can obtain the battery from Siemens spare parts service. It is shipped
ready for installation with a cable and a connector
. Refer to our catalog
ST80.1 for the order number
.
T
o install the battery
, proceed as follows:
Step Action
1
Insert the battery in the battery compartment at the rear of the TD.
The snap-in plastic bracket secures the battery in the battery
compartment.
2
Insert the connector on the battery lead in the two-pin plug con
-
nector on the underside of the TD (refer to Figure 8-1). The con
-
nector is coded and thus protected against polarity reversal.
3
Stow any excess lead in the battery compartment.
Battery
compartment
Figure 8-2 Battery Compartment for Optional Battery
Function
Source of supply
Installing the
battery
Device Description
8-4 TD17
Equipment Manual
Edition 06/97
A
typical service life under normal operating conditions is approximately
four years. The dischar
ge degree of the backup battery is not monitored by
the TD17.
Note
Please comply with the safety notes on the proper handling and disposal of
lithium batteries, which are enclosed with batteries.
8.2 Maintenance
The TD17 is designed for low-maintenance operation. Maintenance of the
TD is limited to
regular cleaning of the keyboard overlay and the display
changing the optional backup battery (refer to Section 8.1).
Clean the keyboard overlay and the TD display at regular intervals with a
damp cloth. Use only water for dampening the cloth. A
void using aggressive
cleaners which may result in damage to the foil front.
Service life
Scope
Cleaning
Device Description
A-1
TD17
Equipment Manual
Edition 06/97
System Messages
TD
system messages can be assigned to dif
ferent categories.
The information concerning the category to which a message belongs is in
-
cluded in the message number:
message
text
Message
number
0
Driver error
1
Startup message
2 Warning
3 Note
4
Operating error
5
Other message
6
Configuration error
7
Internal error
The
message category allows you approximately to localize the cause of an
error message. A list is provided in the following of the occasions on which
selected important messages occur and how the cause of the dif
ferent errors
can be eliminated. Self-explanatory system messages have not been included.
Note
If configuration data are not available to the TD, messages are displayed in
English.
Comply with the following procedure for all system messages referring to
”internal errors”:
a) T
urn of
f the TD, return the PLC to ST
OP and then let both restart.
b)
Place the TD during startup in Download mode (refer to Section 7.1),
download the configuration once again and let the TD and the PLC re
-
start.
c)
Should the error still occur
, please contact your local branch of
fice.
Should you do so, quote the number of the error message that occurred,
together with any variables that may be contained in the message.
Message
number
Procedure for
”internal errors”
A
A-2 TD17
Equipment Manual
Edition 06/97
No. Cause Remedy
5 Error
message if nothing is configured for a system message.
40
Driver error
. If F
AP is set, the character
delay time may also be set too short. Check physical connection to PLC, change
character delay time.
45
Connection cannot be established to PLC.
Set dif
ferent CPU at ”PLC –> Parameters”.
136
PLC not responding.
Check program execution on the PLC and
the physical connection.
138
Data block not present on PLC.
Create a suitable memory area.
201
Hardware fault in clock module.
Return device for repair
.
202
Error upon reading date.
Return device for repair
.
210
The TD or OP coordination area cannot be
received during startup.
Restart by pressing the key
. Press key
.
212
The bit for changing the operating mode has
been erroneously inverted. Restart the TD or OP
.
213 Of
fline mode currently unavailable.
Repeat mode change later
.
214
The job number sent by the PLC or config
-
ured in a function field is too high.
Check the PLC program.
222 W
arning: The event buf
fer is full right up to
the remaining size.
Delete buf
fer or configure smaller remaining
buf
fer size.
303
The connection to the PLC is faulty
.
Check the state of the PLC.
305
The data block number is missing.
Create data block, modify configuration.
306
The wrong PLC has been set under ”PLC –>
Parameters”.
Modify the configuration and download it
once again.
307 to
311 V
ariable not present on the PLC. Check the configuration for the process in
-
terfacing.
317
Input inhibited by password.
Enter password.
322
The password you entered is too short. Enter a password containing at least three
characters.
323
<– Statistics or Message T
ext–> was pressed
on a buffer screen but there is no entry for
the current message.
––
342
Unauthorized node address.
Maximum addresses:
S7-MPI: 32
PROFIBUS-DP: 128
359
The CPU is at ST
OP.
A critical message when S7 messages are
not present.
500 to
503
The scheduler
, counter
, date or time cannot
be sent.
The error may occur if the PLC is tempo
-
rarily overloaded or if the function block has
not been called up for more than 1.5 sec.
504
Free ASCII protocol: It was not possible to
send the operator input value.
The error may occur if the PLC is tempo
-
rarily overloaded or if the function block has
not been called up for more than 1.5 sec.
S
y
stem
Messa
g
es
A-3
TD17
Equipment Manual
Edition 06/97
RemedyCauseNo.
512 The
data block has been configured too
short.
The variable transferred with the message
identifies the number of a data block which
has been made too short.
Modify the configuration and download it
once again.
541 to
550
The specified variable is not present on the
PLC.
Modify the configuration and download it
once again.
551
No MPI/PPI connection to the PLC can be
established with the specified station ad
-
dress.
Check the MPI station addresses and cables.
570 V
ariable is faulty: The parameter used is the
variable name from ProT
ool.
Check the configuration: Occurs frequently
with NC variables and multiplexing.
602
Configuration for remaining buf
fer size in
-
correct.
Correct the remaining buf
fer size and down
-
load the configuration once again.
604
Message does not exist.
Configure message.
606 T
oo many message variables configured.
Modify the configuration and download it
once again.
607
The configured data type is invalid. Modify the configuration and download it
once again.
609
Special object or operator object for mes
-
sage text is not present or is illegal.
Modify the configuration and download it
once again.
613
Data block not present or too short.
Create data block of requisite length on
PLC.
616 W
rong data format in process link.
Correct data format.
617 W
rong word length in process link.
Correct word length.
620
Illegal keyboard ID: too high module num
-
ber or total number of keys dif
fers from key
-
board ID.
Enter configuration complying with hard
-
ware.
621 W
rong parameter transferred: message type.
Set required value by means of standard
screen or PLC.
627
Configured keyboard block number too
high.
Correct block number
.
630
Keyboard assignment area too small. Make keyboard assignment area lar
ger in
keeping with bit numbers used.
631
Message configuration #@\005 incomplete
or incorrect.
Make addition to configuration.
If the error is not corrected following a re
-
start, contact the SIMATIC help desk.
636
Event message No. @ not configured.
Configure event message (–> message num
-
ber) in full.
637
Configuration for a event message missing.
Configure event message (–> message num
-
ber) in full.
S
y
stem
Messa
g
es
A-4 TD17
Equipment Manual
Edition 06/97
RemedyCauseNo.
645 The
PLC coordination area cannot be re
-
ceived during startup.
Restart by pressing the key
.
If the error is not corrected following a re
-
start, contact the SIMATIC help desk.
649
The configured driver number cannot be in
-
terpreted.
If the error is not corrected following a re
-
start, contact the SIMATIC help desk.
650
Area pointer missing.
Configure an area pointer
.
652
Configuration is not compatible with S5. Modify the configuration and download it
once again. If the error is not corrected fol
-
lowing a restart, contact the SIMA
TIC help
desk.
668
Incorrect configuration.
Meaning of variables:
1:
Non-combinable PLC types configured.
2:
No PLC configured.
3: W
rong baud rate configured.
Modify the configuration and download it
once again.
701
Job cannot be executed: Internal actual
value error
.
Change interface or configure area pointer
.
703
The wrong PLC has been set under ”PLC –>
Parameters”.
Modify the configuration and download it
once again.
734
Illegal RIO function.
The following are allowed: Read, write,
(LEDs, outputs) and initialization.
779
Internal error upon MPI download; possibly
buf
fer problems.
Reset and retry
.
S
y
stem
Messa
g
es
B-1
TD17
Equipment Manual
Edition 06/97
Technical Data
Housing
External dimensions
W x H x D (mm) 240 x 98 x 513)
Mounting cutout
W x H (mm) 231+1 x 89+1
Mounting depth (mm) 471)
Degree of protection
– Front
– Rear IP65
IP20
Weight approx. (kg) 0.960
1) Without cable lug under the bonding screw
Memory
Flash memory for configuration data
and data records 128 KB
Display
Type LCD with LED back lighting
Number of lines 4 or 8
(configurable)
Characters per line 20 or 40
(depending on number of lines)
Character height (mm) 11 or 6
(depending on number of lines)
Keyboard
Type Membrane keyboard
Number of system keys 7
B
B-2 TD17
Equipment Manual
Edition 06/97
Power supply
Rated voltage + 24 V DC
Permissible range +18 to +30 VDC
Maximum permissible transients 35 V (500 msec)
Time between two
transients 50 sec minimum
Power input (at 24 V)
till
340 A
– typically
– maximum continuous current 340 mA
390 mA
Fuse
– internal
– external electronic fuse
1.6 A, quick-blow
Backup
Internal Several days at 40 °C 4)
External backup battery 5)
(optional) Lithium battery
3.6 V/approx. 1.5 Ah
> 4 years
4) The specified backup times apply only when the power supply has been connected for more
than 12 hours.
5) Subject to change.
Interfaces
RS232 1
TTY 1
RS422/485 1
PPI/MPI/PROFIBUS-DP
(up to 1.5 MBd)/RS422/485 1
PPI/MPI/PROFIBUS-DP
(up to 12 MBd)/RS422/485 1
Technical
Data
B-3
TD17
Equipment Manual
Edition 06/97
Ambient conditions
Operating temperature
– Vertical installation
– Horizontal installation
Shipping, storage
0 °C to 50 °C
0 °C to 35 °C
–25 °C to 70 °C
Relative humidity
– Operation
– Shipping, storage ≤ 95% no moisture condensation
≤ 95%
Shock load
– Operation
– Shipping, storage 5 g/11 ms
25 g/6 ms
Vibration
Operation
Shipping, storage
0.075 mm (10 Hz to 58 Hz)
1 g (58 Hz to 500 Hz)
3.5 mm (5 Hz to 12 Hz)
1 g (12 Hz to 500 Hz)
Maximum difference in pressure
(front/rear) 2 hPa
Air pressure
– Operation
– Shipping, storage 706 to 1030 hPa
581 to 1030 hPa
Noise immunity EN 50082-1
Static discharge
(contact discharge) EN 61000-4-2 Class 3
RF irradiation ENV 50140 Class 3
Pulse modulation ENV 50204 (900 MHz 5 MHz)
RF conduction ENV 50141 Class 3
Burst interference EN 61000-4-Class 3
Radio interference
RFI suppression level to EN 55011 Class A
Technical
Data
B-4 TD17
Equipment Manual
Edition 06/97
Technical
Data
Index-1
TD17
Equipment Manual
Edition 06/97
Index
A
Access
protection, 4-3
Additional information , 1-3
Adjust, Contrast, 4-5
Adjust driver
, 2-2
AEG/Modicon, 2-2
Allen Bradley
, 2-2
Ambient conditions, B-3
Arrow keys, 3-1
AS51
1, 2-2, 8-2
Assignment
Interfaces, 6-8
System keyboard, 4-8
B
Back-lighting, 1-4
Back-up time, 1-4, 4-6, 5-5
Backup
Operating data, 8-3
T
ime, 8-3
Backup battery
, 1-4, B-2
Upgrading, 8-3
Battery
, Upgrading, 8-3
Buffer
, Messages, 5-2
Buf
fer overflow
, 5-7
Event messages, 5-8
System messages, 5-8
Buf
fer size, 5-2
Burst interference, B-3
Bus fault LED, 7-6
C
Cabinet, 6-1
Cable cross-section, 6-4
Cables, 6-3
Call
Information text, 3-2
Standard screens, 4-4
Cancel, 3-1
Download mode, 3-1, 7-3, 7-4
Information text display
, 3-1
Change
Configuration, 7-4
Contrast, 4-5
Date, 4-6
Operating level, 4-4
Operating mode, 4-7
R
TS signal, 6-7
Summer time/winter time, 4-6
T
ime, 4-6
Character height, 1-4, 2-1, B-1
Character set, 1-3
Characters, per line, 1-4, 2-1, B-1
Chassis ground, 6-5
Cleaning, TD, 8-4
Commissioning, 6-1, 7-1, 7-3
Communication
TD and PLC, 4-8
T
esting, Online, 7-6
Communication methods, 2-2
Communication options, 8-2
Compression, Program memory
, 7-2
Configurable languages, 2-1
Configuration, 1-1
Changing, 7-4
Configuration computer
, 6-5
Interface IF1B, 6-7
Loading, 4-1, 7-3
Overwriting, 7-4
PLC, 6-6
Replacing, 7-4
T
esting, Online, 7-6
Configuration computer
, 7-3, 7-4
Connecting, 6-5
Configuration software, 1-1
Connect
Chassis ground, 6-5
Configuration computer
, 6-5
PC/PU, 8-2
PLC, 6-6
Connecting, Voltage supply
, 6-4
Connection, PLC/Computer
, 1-4
Connection configuration diagram
Configuration computer
, 6-5
PLC, 6-6
Index-2 TD17
Equipment Manual
Edition 06/97
Connection
elements, 8-2
Connection types, 6-6
Connections, electrical, 6-3
Connector
, Battery
, 8-3
Connectors, 8-2
Removing, 7-2
Console, 6-1
Continuous current, B-2
Contrast, 2-1
Adjust, 4-5
Control value, 1-3
Create data areas, 1-1
Cross-jump destination, 4-2
Cross-section, Connecting cables, 6-4
Cyrillic characters, 1-3
D
Damp, 6-1
Data areas, 4-8
Data buf
fer
, 1-4
Date, 4-8
Changing, 4-6
Output, 5-2
Setting, 4-4, 4-6
Degree of protection, B-1
Delete
Event buf
fer
, 4-4, 5-8
Event message, 5-7
System message buf
fer
, 5-8
Design
Electromagnetic compatible, 6-3
Hardware, 6-3
TD17, 1-4
Design directives, 6-3
DF1 driver
, 2-2
Diagnosis, Fault, 7-4
Dimensions, 8-1, B-1
DIP switch, Interface IF1B, 6-7
Directives, Interference Immunity
, 6-3
Dischar
ge degree, Backup battery
, 8-4
Display
, 2-1, B-1
Contrast adjustment, 4-5
Event buf
fer
, 4-4
Event messages, 4-4
Language-dependent, 1-3
Malfunctions, 5-1
Message text, 4-4
Messages, 5-4
Operating state, 5-1, 5-3
Standby message, 7-3, 7-4
System message buf
fer
, 4-4
T
ype, B-1
Display functions, 1-3
Display priority
, 5-3, 5-4
Displays, Events and states, 5-1
Disposal, Battery
, 8-4
Download
Configuration, 7-3
Firmware, 7-3
Download mode, 4-1, 4-4, 4-7, 7-3, 7-5
Cancel, 3-1, 7-3, 7-4
Drilled holes for mounting, 6-1
Drilling, Mounting device, 6-1
Driver
, 2-2
Drivers, for Other PLCs, 2-2
Duration of display
, System messages, 5-3
E
Electrical connections, 6-3
Electrical installation, 6-3
EMC, Design, 6-3
Emission, Radio interference, B-3
ENTER, 3-1, 4-2
Error handling, A-1
ESC, 3-1, 4-2
Event buf
fer
, 5-2
Deleting, 4-4, 5-7, 5-8
Display
, 4-4
V
iewing, 5-6
Event messages, 1-3, 5-1
Maximum length, 2-1
Maximum number
, 2-1
Scrolling, 5-5
Events
Displaying, 5-1
Storing in message buf
fer
, 5-2
External PLC, 8-2
F
FAP
, 2-2, 8-2
Fault diagnosis, 7-4
Fields, V
ariable, 5-2
Firmware, 5-3
Loading, 7-3
Flash memory, B-1
Flashing display
, 5-2
Index
Index-3
TD17
Equipment Manual
Edition 06/97
Foreign
languages, 1-3
Front panel, Thickness, 6-1
Functions
in standard screens, 4-4
of TD, 1-3, 2-1
Fuse, 1-4, B-2
FX driver, 2-2
G
Grounding, 6-5
H
Hardware clock, 4-6
Hardware design, 6-3
Hazardous area, 7-2
HELP key, 3-1
Hide, System message, 3-1, 4-2
Hints on operation, 1-3, 5-1
History
, Messages, 5-5
Humidity
, B-3
I
IF1B interface, Configuring, 6-7
Information text, 1-3, 2-1, 3-2
Inhibit, System message, 5-4
Initial startup, 7-1, 7-3
Initializations, 7-5
Initiate
Messages, 5-1
System message, 5-1
Installation, 6-1
Electrical, 6-3
Mechanical , 6-2
TD, 6-2
Installation conditions, 6-1
Interfaces, 8-2, B-2
Assignment, 6-8
Interference-free operation, 6-3
Internal error
, A-1
Interruption, Power supply
, 8-3
Issued, Message, 5-2
K
Key combinations, 3-2
Keyboard, 3-1, B-1
Keys, 3-1, 4-2
L
Contrast setting, 4-4
Language setting, 4-5
Languages, 1-3
LED, Bus fault, 7-6
Lines, Number
, 1-4, 2-1, B-1
Load
Configuration, 4-1, 7-3
Firmware, 7-3
Language, 4-5
Loadable convenience drivers, 2-2
M
Maintenance, 8-4
Malfunctions, Display
, 5-1
Maloperation, 4-8, 5-1, 5-3
Measurements, 8-1
Mechanical installation, 6-2
Message bit procedure, 5-2
Message buf
fer
, 5-1, 5-2, 5-4
Message history
, 5-5
Message level, 4-1
Message priorities, 5-4
Message types, 5-1
Messages, 5-1
Arrived, 5-2
Deleting, 5-7
Departed, 5-2
Display
, 4-1, 5-4
Event messages, 1-3, 5-1
First, 5-4
Last, 5-4
Number
, A-1
Scrolling, 5-5
System messages, 5-3
Mitsubishi, 2-2
Modbus driver
, 2-2
Moisture condensation, 6-1
Mounting, 6-2
Mounting cutout, 6-1, 8-1, B-1
MPI, 2-2, 8-2
N
NA
TIVE drivers, 2-2
NITP driver
, 2-2
Noise immunity
, B-3
Normal operation, 7-1
Index
Index-4 TD17
Equipment Manual
Edition 06/97
O
Offline
mode, 4-4, 4-7
Online mode, 4-4, 4-7, 7-6
Operating data, Backup, 8-3
Operating level, 4-1
Changing, 4-2
Operating mode
Download, 7-3
Online, 7-6
Setting, 4-4, 4-7
Operating state, Display
, 5-1, 5-3
Operating temperature, B-3
Operating the TD
by keyboard, 3-1
from PLC, 4-8
Operation, Interference-free, 6-3
Other PLCs, 8-2
Overall reset, 3-2
Overflow
, Message buf
fer
, 5-7
Overflow warning, 5-2, 5-8
Overwrite, Configuration, 7-4
P
Password protection, 4-3
PC or PU, 7-4
PC/PU, 7-3, 8-2
PLC, 1-4
Connecting, 6-6
PLC job, 4-8
Plug connections, 6-3
Polling time, 5-2
Power input, B-2
Power supply
, 6-5, B-2
Backup battery
, 8-3
Connecting, 6-4
PPI, 2-2, 8-2
Pressure difference, B-3
Priority
, Messages, 5-3, 5-4
Process values, 1-3
PROFIBUS–DP
, Communication testing, 7-6
PROFIBUS-DP
, 2-2, 8-2
Protection, B-2
against unauthorized access, 4-3
R
Radio interference, B-3
Rated voltage, B-2
Recommissioning, 7-1, 7-4
Reference, 1-2
Relative humidity
, B-3
Remaining size, Event buf
fer
, 5-8
Remaining space, Event buf
fer
, 5-2
Remedy
, System message, A-2
Replace, Configuration, 7-4
Restart, 5-3, A-1
RFI suppression level, B-3
RS232, 1-4, 8-2
RS422, 1-4, 8-2
RS485, 1-4, 8-2
R
TS signal, Changing, 6-7
S
Save, System messages, 5-4
Screw type clamps, 6-2
Scrolling
in information text, 3-2
in messages, 3-1, 5-5
Securing, TD, 6-2
Self test, 7-5
Service life, Backup battery
, 8-4
Set
Date and T
ime, 4-4
Language, 4-5
Operating mode, 4-4, 4-7
Summer time/winter time, 4-6
Shipping conditions, B-3
Signal lines, 6-3
SIMA
TIC 500/505, 2-2, 8-2
SIMA
TIC M7, 2-2, 8-2
SIMA
TIC S5, 2-2, 8-2
SIMA
TIC S7, 2-2, 8-2
Size, B-1
Source of supply
, Backup battery
, 8-3
Spare parts service, 8-3
Standard cables, 6-6
Standard screen level, 4-1
Standard screens, 4-1, 4-4
Calling, 4-4
Change modes, 4-7
Change modes, Download, 7-4
Delete event message buf
fer
, 5-7
Directory
, 4-4
Display event message buf
fer
, 5-6
Display system message buf
fer
, 5-6
Set contrast, 4-5
Set Date & T
ime, 4-6
Set language, 4-5
Standby message, 5-2, 7-3, 7-4
Startup behavior
, 7-5
Startup of TD, 4-1
Index
Index-5
TD17
Equipment Manual
Edition 06/97
Static
text, 1-2
STOP
, PLC, A-1
Storage conditions, B-3
Summer time, Setting, 4-6
Supervisor password, 4-3
Switch
Interface IF1B, 6-7
Operating mode, 4-7
Synchronize, Date and time, 4-8
System keyboard, 1-4, 3-1, B-1
Assignment, 4-8
System message, 5-1, 5-3
Hide, 3-1, 4-2
Inhibiting, 5-4
List, A-1
Non–serious, 5-3
Serious, 5-3
System message buf
fer
, 5-4
Deleting, 5-8
Display
, 4-4
V
iewing, 5-6
System settings, 4-4
T
TD, Installing, 6-2
TD17
Design, 1-4
Functions, 2-1
Operating mode, 4-7
Startup, 4-1
T
echnical Data, B-1
T
elemecanique, 2-2
T
emperature, B-3
T
erminal block, 6-4
Test
Communication, Online, 7-6
Configuration, Online, 7-6
Testing
Communication, Online, 7-6
Configuration, online, 7-6
Thickness, Front panel, 6-1
T
ime, 4-8
Backup, 8-3
Changing, 4-6
Output, 5-2
Setting, 4-4, 4-6
T
ime and date, Changing, 4-6
T
ouch-sensitive front, 1-4
Transfer
Date, 4-8
T
ime, 4-8
TTY
, 1-4, 8-2
T
urn on
Device, 7-3, 7-4
TD, 6-1
U
Uni-T
elway driver
, 2-2
V
V
ariable fields, 5-2
V
ariable text, 1-2
V
ersion, Firmware, 5-3
View
Event buf
fer
, 5-6
System message buf
fer
, 5-6
V
oltage supply
, 6-4
W
W
arning, Buf
fer overflow
, 5-2, 5-8
W
eight, B-1
W
inter time, Setting, 4-6
Index
Index-6 TD17
Equipment Manual
Edition 06/97
Index
