LTC3890-1 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller DESCRIPTION FEATURES n n n n n n n n n n n n n n n n The LTC(R)3890-1 is a high performance dual step-down switching regulator DC/DC controller that drives all N-channel synchronous power MOSFET stages. A constant frequency current mode architecture allows a phaselockable frequency of up to 850kHz. Power loss and supply noise are minimized by operating the two controller output stages out-of-phase. Wide VIN Range: 4V to 60V (65V Abs Max) Low Operating IQ: 50A (One Channel On) Wide Output Voltage Range: 0.8V VOUT 24V RSENSE or DCR Current Sensing Out-of-Phase Controllers Reduce Required Input Capacitance and Power Supply Induced Noise Phase-Lockable Frequency (75kHz to 850kHz) Programmable Fixed Frequency (50kHz to 900kHz) Selectable Continuous, Pulse-Skipping or Low Ripple Burst Mode(R) Operation at Light Loads Very Low Dropout Operation: 99% Duty Cycle Adjustable Output Voltage Soft-Start or Tracking Power Good Output Voltage Monitor Output Overvoltage Protection Low Shutdown IQ: <14A Internal LDO Powers Gate Drive from VIN or EXTVCC No Current Foldback During Start-Up Narrow SSOP Package The 50A no-load quiescent current extends operating life in battery-powered systems. OPTI-LOOP(R) compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. A wide 4V to 60V input supply range encompasses a wide range of intermediate bus voltages and battery chemistries. Independent TRACK/SS pins for each controller ramp the output voltages during start-up. Current foldback limits MOSFET heat dissipation during short-circuit conditions. The PLLIN/MODE pin selects among Burst Mode operation, pulse-skipping mode, or continuous conduction mode at light loads. APPLICATIONS n n n For a leadless 32-pin QFN package with additional features of adjustable current limit, clock out, phase modulation and two PGOOD outputs, see the LTC3890 data sheet. Automotive Always-On Systems Battery Operated Digital Devices Distributed DC Power Systems L, LT, LTC, LTM, Linear Technology, Burst Mode, OPTI-LOOP and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258, 7230497. TYPICAL APPLICATION High Efficiency Dual 8.5V/3.3V Output Step-Down Converter Efficiency and Power Loss vs Output Current VIN 9V TO 60V 22F 4.7F VIN TG2 BOOST2 SW1 SW2 BG1 BG2 LTC3890-1 0.1F 8H PGND SENSE1+ SENSE2+ SENSE1- VFB1 ITH1 SENSE2- VFB2 ITH2 0.01 100k 470F 1000pF 31.6k 34.8k TRACK/SS1 SGND TRACK/SS2 0.1F 0.1F 80 1000 70 100 60 50 10 40 30 0.008 VOUT1 3.3V 5A 10000 100k 1000pF 10.5k 20 VOUT2 8.5V 3A 330F POWER LOSS (mW) BOOST1 EFFICIENCY (%) TG1 0.1F 4.7H 100 VIN = 12V 90 VOUT = 3.3V INTVCC 1 10 0 0.0001 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 0.1 10 38901 TA01b 34.8k 38901 TA01a 38901fa 1 LTC3890-1 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) Input Supply Voltage (VIN) ......................... -0.3V to 65V Topside Driver Voltages BOOST1, BOOST2 ..................................-0.3V to 71V Switch Voltage (SW1, SW2) ......................... -5V to 65V (BOOST1-SW1), (BOOST2-SW2) ................ -0.3V to 6V RUN1, RUN2 ............................................... -0.3V to 8V Maximum Current Sourced into Pin from Source >8V...................................................100A SENSE1+, SENSE2+, SENSE1- SENSE2- Voltages ..................................... -0.3V to 28V PLLIN/MODE Voltage ................................... -0.3V to 6V FREQ Voltage ........................................ -0.3V to INTVCC EXTVCC ..................................................... -0.3V to 14V ITH1, ITH2, VFB1, VFB2 Voltages ................... -0.3V to 6V PGOOD1 Voltage ......................................... -0.3V to 6V TRACK/SS1, TRACK/SS2 Voltages ............. -0.3V to 6V Operating Junction Temperature Range (Notes 2, 3) LTC3890E-1, LTC3890I-1 ................... -40C to 125C LTC3890H-1 ....................................... -40C to 150C LTC3890MP-1 .................................... -55C to 150C Storage Temperature Range .................. -65C to 150C TOP VIEW ITH1 1 28 TRACK/SS1 VFB1 2 27 PGOOD1 SENSE1+ 3 26 TG1 SENSE1- 4 25 SW1 FREQ 5 24 BOOST1 PLLIN/MODE 6 23 BG1 SGND 7 22 VIN RUN1 8 21 PGND RUN2 9 20 EXTVCC SENSE2- 10 19 INTVCC SENSE2+ 11 18 BG2 VFB2 12 17 BOOST2 ITH2 13 16 SW2 TRACK/SS2 14 15 TG2 GN PACKAGE 28-LEAD PLASTIC SSOP TJMAX = 150C, JA = 90C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3890EGN-1#PBF LTC3890EGN-1#TRPBF LTC3890GN-1 28-Lead Plastic SSOP -40C to 125C LTC3890IGN-1#PBF LTC3890IGN-1#TRPBF LTC3890GN-1 28-Lead Plastic SSOP -40C to 125C LTC3890HGN-1#PBF LTC3890HGN-1#TRPBF LTC3890GN-1 28-Lead Plastic SSOP -40C to 150C LTC3890MPGN-1#PBF LTC3890MPGN-1#TRPBF LTC3890GN-1 28-Lead Plastic SSOP -55C to 150C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 38901fa 2 LTC3890-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted. (Note 2) SYMBOL PARAMETER VIN Input Supply Operating Voltage Range VFB1,2 Regulated Feedback Voltage CONDITIONS ITH1,2 Voltage = 1.2V (Note 4) -40C to 85C, All Grades LTC3890E-1, LTC3890I-1, LTC3890H-1, LTC3890MP-1 IFB1,2 Feedback Current (Note 4) Reference Voltage Line Regulation VIN = 4.5V to 60V (Note 4) VLOADREG Output Voltage Load Regulation (Note 4) Measured in Servo Loop, ITH Voltage = 1.2V to 0.7V (Note 4) Measured in Servo Loop, ITH Voltage = 1.2V to 2V gm1,2 Transconductance Amplifier gm IQ Input DC Supply Current (Note 5) Pulse-Skipping or Forced Continuous Mode (One Channel On) l l 0.792 0.788 0.786 UNITS 60 V 0.808 0.812 0.812 V V V 5 50 nA 0.02 %/V l 0.01 0.1 % l -0.01 -0.1 % 2 mmho RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V or RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V 2 mA Pulse-Skipping or Forced Continuous Mode (Both Channels On) RUN1,2 = 5V, VFB1,2 = 0.83V (No Load) 2 mA Sleep Mode (One Channel On) RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V or RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V 50 75 A Sleep Mode (Both Channels On) RUN1,2 = 5V, VFB1,2 = 0.83V (No Load) 60 100 A Shutdown RUN1,2 = 0V 14 25 A Undervoltage Lockout INTVCC Ramping Up INTVCC Ramping Down 3.6 3.92 3.80 4.2 4.0 V V 7 10 13 % 1 A 1 700 A A 99 % Feedback Overvoltage Protection Measured at VFB1,2, Relative to Regulated VFB1,2 ISENSE+ ISENSE- SENSE+ Pin Current Each Channel SENSE- Pins Current Each Channel VSENSE- < INTVCC - 0.5V VSENSE- > INTVCC + 0.5V Maximum Duty Factor l l In Dropout ITRACK/SS1,2 Soft-Start Charge Current VTRACK1,2 = 0V VRUN1 On VRUN2 On RUN1 Pin On Threshold RUN2 Pin On Threshold VRUN1 Rising VRUN2 Rising 98 l l 0.7 1.0 1.4 A 1.15 1.20 1.21 1.25 1.27 1.30 V V VRUN1,2 Hyst RUN Pin Hysteresis VSENSE(MAX) 0.800 0.800 0.800 MAX 0.002 ITH1,2 = 1.2V, Sink/Source = 5A (Note 4) VOVL DFMAX TYP 4 VREFLNREG UVLO MIN Maximum Current Sense Threshold 50 VFB1,2 = 0.7V, VSENSE1-, 2- = 3.3V, ILIM = 0 l 64 75 mV 85 mV Gate Driver TG1,2 Pull-Up On-Resistance Pull-Down On-Resistance 2.5 1.5 BG1,2 Pull-Up On-Resistance Pull-Down On-Resistance 2.4 1.1 TG1,2 tr TG1,2 tf TG Transition Time: Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 25 25 ns ns BG1,2 tr BG1,2 tf BG Transition Time: Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 25 25 ns ns 38901fa 3 LTC3890-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS TG/BG t1D Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time CLOAD = 3300pF Each Driver 30 ns BG/TG t1D Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time CLOAD = 3300pF Each Driver 30 ns tON(MIN) Minimum On-Time (Note 7) 95 ns INTVCC Linear Regulator VINTVCCVIN Internal VCC Voltage 6V < VIN < 60V, VEXTVCC = 0V VLDOVIN INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 0V VINTVCCEXT Internal VCC Voltage 6V < VEXTVCC < 13V VLDOEXT INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 8.5V VEXTVCC EXTVCC Switchover Voltage EXTVCC Ramping Positive VLDOHYS EXTVCC Hysteresis 4.85 4.85 4.5 5.1 5.35 V 0.7 1.1 % 5.1 5.35 V 0.6 1.1 % 4.7 4.9 V 250 mV Oscillator and Phase-Locked Loop f25k Programmable Frequency RFREQ = 25k, PLLIN/MODE = DC Voltage f65k Programmable Frequency RFREQ = 65k, PLLIN/MODE = DC Voltage 105 f105k Programmable Frequency RFREQ = 105k, PLLIN/MODE = DC Voltage fLOW Low Fixed Frequency VFREQ = 0V, PLLIN/MODE = DC Voltage 320 350 380 kHz fHIGH High Fixed Frequency VFREQ = INTVCC, PLLIN/MODE = DC Voltage 485 535 585 kHz fSYNC Synchronizable Frequency PLLIN/MODE = External Clock 850 kHz 0.4 V 1 A 375 440 kHz 505 835 l 75 kHz kHz PGOOD1 Output VPGL PGOOD1 Voltage Low IPGOOD PGOOD1 Leakage Current VPGOOD = 5V VPG PGOOD1 Trip Level VFB with Respect to Set Regulated Voltage VFB Ramping Negative Hysteresis -13 -10 2.5 -7 % % VFB with Respect to Set Regulated Voltage VFB Ramping Positive Hysteresis 7 10 2.5 13 % % tPG IPGOOD = 2mA Delay for Reporting a Fault Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Ratings for extended periods may affect device reliability and lifetime. Note 2: The LTC3890-1 is tested under pulsed load condition such that TJ TA.The LTC3890E-1 is guaranteed to meet performance specifications from 0C to 85C. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3890I-1 is guaranteed over the -40C to 125C operating junction temperature range, the LTC3890H-1 is guaranteed over the -40C to 150C operating junction temperature range and the LTC3890MP-1 is tested and guaranteed over the -55C to 150C operating junction temperature range. High junction temperatures degrade operating lifetimes; operating lifetime is derated for junction temperatures greater than 125C. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. 0.2 25 s Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: TJ = TA + (PD * 90C/W) Note 4: The LTC3890-1 is tested in a feedback loop that servos VITH1,2 to a specified voltage and measures the resultant VFB. The specification at 85C is not tested in production and is assured by design, characterization and correlation to production testing at other temperatures (125C for the LTC3890E-1/LTC3890I-1, 150C for the LTC3890H-1/LTC3890MP-1). For the LTC3890MP-1, the specification at -40C is not tested in production and is assured by design, characterization and correlation to production testing at -55C. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See the Applications information section. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: The minimum on-time condition is specified for an inductor peakto-peak ripple current of IMAX (See Minimum On-Time Considerations in the Applications Information section). 38901fa 4 LTC3890-1 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency and Power Loss vs Output Current VIN = 12V 90 VOUT = 3.3V BURST EFFICIENCY 90 100 50 BURST LOSS PULSE-SKIPPING LOSS 40 10 30 CCM EFFICIENCY 20 PULSE-SKIPPING EFFICIENCY 10 0 0.0001 0.001 0.01 0.1 1 OUTPUT CURRENT (A) POWER LOSS (mW) CCM LOSS 60 VOUT = 8.5V 1 50 40 30 94 92 90 84 Burst Mode OPERATION VIN = 12V 0 0.0001 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 82 10 0 38901 G02 FIGURE 13 CIRCUIT VOUT 100mV/DIV ACCOUPLED IL 2A/DIV IL 2A/DIV IL 2A/DIV VIN = 12V VOUT = 3.3V FIGURE 13 CIRCUIT Inductor Current at Light Load FORCED CONTINUOUS MODE 38901 G05 38901 G06 50s/DIV VIN = 12V VOUT = 3.3V FIGURE 13 CIRCUIT VIN = 12V VOUT = 3.3V FIGURE 13 CIRCUIT Soft Start-Up Tracking Start-Up VOUT2 2V/DIV Burst Mode OPERATION 1A/DIV 38901 G03 Load Step Forced Continuous Mode VOUT 100mV/DIV ACCOUPLED 50s/DIV 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) FIGURE 13 CIRCUIT Load Step Pulse-Skipping Mode 38901 G04 ILOAD = 2A 80 VOUT 100mV/DIV ACCOUPLED 50s/DIV VOUT1 = 3.3V 88 86 20 Load Step Burst Mode Operation VOUT2 = 8.5V 96 60 10 0.1 10 98 VOUT = 3.3V 70 38901 G01 FIGURE 13 CIRCUIT 100 80 EFFICIENCY (%) 80 EFFICIENCY (%) 100 1000 70 Efficiency vs Input Voltage Efficiency vs Output Current 10000 EFFICIENCY (%) 100 VOUT2 2V/DIV VOUT1 2V/DIV VOUT1 2V/DIV PULSE-SKIPPING MODE 5s/DIV VIN = 12V VOUT = 3.3V ILOAD = 200A 38901 G07 2ms/DIV FIGURE 13 CIRCUIT 38901 G08 2ms/DIV FIGURE 13 CIRCUIT 38901 G09 38901fa 5 LTC3890-1 TYPICAL PERFORMANCE CHARACTERISTICS Total Input Supply Current vs Input Voltage SUPPLY CURRENT (A) 250 200 300A LOAD 150 100 NO LOAD 50 5.5 5.8 5.6 5.0 5.4 INTVCC VOLTAGE (V) VOUT = 3.3V FIGURE 13 CIRCUIT INTVCC Line Regulation 6.0 EXTVCC AND INTVCC VOLTAGE (V) 300 EXTVCC Switchover and INTVCC Voltages vs Temperature INTVCC 5.2 5.0 EXTVCC RISING 4.8 EXTVCC FALLING 4.6 4.4 4.5 4.0 3.5 4.2 0 4.0 -75 -50 -25 5 10 15 20 25 30 35 40 45 50 55 60 65 INPUT VOLTAGE (V) 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G10 PULSE-SKIPPING MODE Burst Mode OPERATION 20 0 600 500 400 300 200 100 -20 0 FORCED CONTINUOUS MODE -40 0.4 0.6 0.8 VITH (V) 1.0 1.2 -100 1.4 0 5 85 80 75 70 65 15 70 75 QUIESCENT CURRENT (A) 80 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) 38901 G15 Quiescent Current vs Temperature 80 60 0 38901 G14 Foldback Current Limit MAXIMUM CURRENT SENSE VOLTAGE (mV) 90 60 25 20 VSENSE COMMON MODE VOLTAGE (V) 38901 G13 0 10 INTVCC vs Load Current 5.50 VIN = 12V VIN = 12V 5.25 70 EXTVCC = 0V INTVCC VOLTAGE (V) 0.2 Maximum Current Sense Threshold vs Duty Cycle MAXIMUM CURRENT SENSE VOLTAGE (mV) 700 SENSE- CURRENT (A) CURRENT SENSE THESHOLD (mV) 800 60 0 38901 G12 SENSE- Pin Input Bias Current 5% DUTY CYCLE 40 0 5 10 15 20 25 30 35 40 45 50 55 60 65 INPUT VOLTAGE (V) 38901 G11 Maximum Current Sense Voltage vs ITH Voltage 80 ILOAD = 10mA 3.0 65 60 55 50 45 40 5.00 EXTVCC = 8.5V 4.75 EXTVCC = 5V 4.50 4.25 35 0 100 200 300 400 500 600 FEEDBACK VOLTAGE (MV) 700 800 38901 G16 30 -75 -50 -25 4.00 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G17 0 20 60 80 40 LOAD CURRENT (mA) 100 38901 G18 38901fa 6 LTC3890-1 TYPICAL PERFORMANCE CHARACTERISTICS TRACK/SS Pull-Up Current vs Temperature Regulated Feedback Voltage vs Temperature Shutdown (RUN) Threshold vs Temperature 1.40 808 1.05 RUN PIN VOLTAGE (V) TRACK/SS CURRENT (A) 1.35 1.00 0.95 1.30 RUN1 RISING RUN2 RISING 1.25 1.20 1.15 RUN1 FALLING 1.10 RUN2 FALLING 1.05 0.90 -75 -50 -25 1.00 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 400 300 200 100 -100 -75 -50 -25 25 550 20 15 10 3.6 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G25 400 300 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G24 Shutdown Current vs Temperature 22 FREQ = GND VIN = 12V 20 354 SHUTDOWN CURRENT (A) INTVCC VOLTAGE (V) OSCILLATOR FREQUENCY (kHz) 3.7 450 Oscillator Frequency vs Input Voltage 356 3.8 500 38901 G23 4.2 FALLING FREQ = INTVCC FREQ = GND 5 10 15 20 25 30 35 40 45 50 55 60 65 INPUT VOLTAGE (V) Undervoltage Lockout Threshold vs Temperature RISING 0 25 50 75 100 125 150 TEMPERATURE (C) 350 38901 G22 3.9 794 600 0 4.0 796 30 0 25 50 75 100 125 150 TEMPERATURE (C) 4.1 798 Oscillator Frequency vs Temperature 5 VOUT < INTVCC - 0.5V 0 800 38901 G21 FREQUENCY (kHz) SHUTDOWN CURRENT (A) SENSE- CURRENT (A) 500 802 Shutdown Current vs Input Voltage 800 VOUT > INTVCC + 0.5V 804 38901 G20 SENSE- Pin Total Input Bias Current vs Temperature 600 806 792 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G19 700 REGULATED FEEDBACK VOLTAGE (mV) 1.10 352 350 348 346 18 16 14 12 10 344 5 10 15 20 25 30 35 40 45 50 55 60 65 INPUT VOLTAGE (V) 38901 G26 8 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 38901 G27 38901fa 7 LTC3890-1 PIN FUNCTIONS ITH1, ITH2 (Pin 1, Pin 13): Error Amplifier Outputs and Switching Regulator Compensation Points. Each associated channel's current comparator trip point increases with this control voltage. VFB1, VFB2 (Pin 2, Pin 12): Receives the remotely sensed feedback voltage for each controller from an external resistive divider across the output. SENSE1+, SENSE2+ (Pin 3, Pin 11): The (+) input to the differential current comparators are normally connected to DCR sensing networks or current sensing resistors. The ITH pin voltage and controlled offsets between the SENSE- and SENSE+ pins in conjunction with RSENSE set the current trip threshold. SENSE1-, SENSE2- (Pin 4, Pin 10): The (-) Input to the Differential Current Comparators. When greater than INTVCC - 0.5V, the SENSE- pin supplies current to the current comparator. FREQ (Pin 5): The Frequency Control Pin for the Internal VCO. Connecting the pin to GND forces the VCO to a fixed low frequency of 350kHz. Connecting the pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. Other frequencies between 50kHz and 900kHz can be programmed using a resistor between FREQ and GND. An internal 20A pull-up current develops the voltage to be used by the VCO to control the frequency. PLLIN/MODE (Pin 6): External Synchronization Input to Phase Detector and Forced Continuous Mode Input. When an external clock is applied to this pin, the phase-locked loop will force the rising TG1 signal to be synchronized with the rising edge of the external clock. When not synchronizing to an external clock, this input, which acts on both controllers, determines how the LTC3890-1 operates at light loads. Pulling this pin to ground selects Burst Mode operation. An internal 100k resistor to ground also invokes Burst Mode Operation when the pin is floated. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.2V and less than INTVCC - 1.3V selects pulse-skipping operation. SGND (Pin 7): Small-signal ground common to both controllers, must be routed separately from high current grounds to the common (-) terminals of the CIN capacitors. RUN1, RUN2 (Pin 8, Pin 9): Digital Run Control Inputs for Each Controller. Forcing RUN1 below 1.16V or RUN2 below 1.20V shuts down that controller. Forcing both of these pins below 0.7V shuts down the entire LTC3890-1, reducing quiescent current to approximately 14A. INTVCC (Pin 19): Output of the Internal Linear Low Dropout Regulator. The driver and control circuits are powered from this voltage source. Must be decoupled to power ground with a minimum of 4.7F ceramic or other low ESR capacitor. Do not use the INTVCC pin for any other purpose. EXTVCC (Pin 20): External Power Input to an Internal LDO Connected to INTVCC. This LDO supplies INTVCC power, bypassing the internal LDO powered from VIN whenever EXTVCC is higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not float or exceed 14V on this pin. PGND (Pin 21): Driver Power Ground. Connects to the sources of bottom (synchronous) N-channel MOSFETs and the (-) terminal(s) of CIN. VIN (Pin 22): Main Supply Pin. A bypass capacitor should be tied between this pin and the signal ground pin. 38901fa 8 LTC3890-1 PIN FUNCTIONS BG1, BG2 (Pin 23, Pin 18): High Current Gate Drives for Bottom (Synchronous) N-Channel MOSFETs. Voltage swing at these pins is from ground to INTVCC. PGOOD1 (Pin 27): Open-Drain Logic Output. PGOOD1 is pulled to ground when the voltage on the VFB1 pin is not within 10% of its set point. BOOST1, BOOST2 (Pin 24, Pin 17): Bootstrapped Supplies to the Topside Floating Drivers. Capacitors are connected between the BOOST and SW pins and Schottky diodes are tied between the BOOST and INTVCC pins. Voltage swing at the BOOST pins is from INTVCC to (VIN + INTVCC). TRACK/SS1, TRACK/SS2 (Pin 28, Pin 14): External Tracking and Soft-Start Input. The LTC3890-1 regulates the VFB1,2 voltage to the smaller of 0.8V or the voltage on the TRACK/SS1,2 pin. An internal 1A pull-up current source is connected to this pin. A capacitor to ground at this pin sets the ramp time to final regulated output voltage. Alternatively, a resistor divider on another voltage supply connected to this pin allows the LTC3890-1 output to track the other supply during start-up. SW1, SW2 (Pin 25, Pin 16): Switch Node Connections to Inductors. TG1, TG2 (Pin 26, Pin 15): High Current Gate Drives for Top N-Channel MOSFETs. These are the outputs of floating drivers with a voltage swing equal to INTVCC - 0.5V superimposed on the switch node voltage SW. 38901fa 9 LTC3890-1 FUNCTIONAL DIAGRAM INTVCC DUPLICATE FOR SECOND CONTROLLER CHANNEL PGOOD1 BOOST DROP OUT DET 0.88V + - VFB1 S Q R Q + 0.72V CB D BOT TOP ON SWITCH LOGIC BOT SHDN CIN SW INTVCC BG COUT - PGND 20A FREQ DB TG TOP VIN VOUT VCO CLK2 0.425V CLK1 + SLEEP RSENSE L - ICMP PFD + - CLP -+ +- IR - SENSE+ + 3mV SYNC DET PLLIN/MODE 2.7V 0.65V SENSE- 100k SLOPE COMP VFB EA - OV - 5.1V 5.1V LDO EN LDO EN 7A (RUN1) 0.5A (RUN2) SHDN RST 2(VFB) + - 0.80V TRACK/SS RA + EXTVCC 4.7V RB + VIN 0.88V ITH CC2 FOLDBACK CSS SHDN INTVCC RC 1A TRACK/SS 11V SGND CC RUN 38901 FD 38901fa 10 LTC3890-1 OPERATION (Refer to the Functional Diagram) Main Control Loop The LTC3890-1 uses a constant frequency, current mode step-down architecture with the two controller channels operating 180 degrees out-of-phase. During normal operation, each external top MOSFET is turned on when the clock for that channel sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The error amplifier compares the output voltage feedback signal at the VFB pin, (which is generated with an external resistor divider connected across the output voltage, VOUT , to ground) to the internal 0.800V reference voltage. When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. After the top MOSFET is turned off each cycle, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. When the EXTVCC pin is tied to a voltage less than 4.7V, the VIN LDO (low dropout linear regulator) supplies 5.1V from VIN to INTVCC. If EXTVCC is taken above 4.7V, the VIN LDO is turned off and an EXTVCC LDO is turned on. Once enabled, the EXTVCC LDO supplies 5.1V from EXTVCC to INTVCC. Using the EXTVCC pin allows the INTVCC power to be derived from a high efficiency external source such as one of the LTC3890-1 switching regulator outputs. Each top MOSFET driver is biased from the floating bootstrap capacitor CB, which normally recharges during each cycle through an external diode when the top MOSFET turns off. If the input voltage, VIN, decreases to a voltage close to VOUT , the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about one-twelfth of the clock period every tenth cycle to allow CB to recharge. Shutdown and Start-Up (RUN1, RUN2 and TRACK/ SS1, TRACK/SS2 Pins) The two channels of the LTC3890-1 can be independently shut down using the RUN1 and RUN2 pins. Pulling either of these pins below 1.15V shuts down the main control loop for that controller. Pulling both pins below 0.7V disables both controllers and most internal circuits, including the INTVCC LDOs. In this state, the LTC3890-1 draws only 14A of quiescent current. Releasing either RUN pin allows a small internal current to pull up the pin to enable that controller. The RUN1 pin has a 7A pull-up current while the RUN2 pin has a smaller 0.5A. The 7A current on RUN1 is designed to be large enough so that the RUN1 pin can be safely floated (to always enable the controller) without worry of condensation or other small board leakage pulling the pin down. This is ideal for always-on applications where one or both controllers are enabled continuously and never shut down. The RUN pin may be externally pulled up or driven directly by logic. When driving the RUN pin with a low impedance source, do not exceed the absolute maximum rating of 8V. The RUN pin has an internal 11V voltage clamp that allows the RUN pin to be connected through a resistor to a higher voltage (for example, VIN), so long as the maximum current into the RUN pin does not exceed 100A. The start-up of each controller's output voltage VOUT is controlled by the voltage on the TRACK/SS pin for that channel. When the voltage on the TRACK/SS pin is less than the 0.8V internal reference, the LTC3890-1 regulates the VFB voltage to the TRACK/SS pin voltage instead of the 0.8V reference. This allows the TRACK/SS pin to be used to program a soft-start by connecting an external capacitor from the TRACK/SS pin to SGND. An internal 1A pull-up current charges this capacitor creating a voltage ramp on the TRACK/SS pin. As the TRACK/SS voltage rises linearly from 0V to 0.8V (and beyond up to 5V), the output voltage VOUT rises smoothly from zero to its final value. Alternatively the TRACK/SS pin can be used to cause the start-up of VOUT to track that of another supply. Typically, this requires connecting to the TRACK/SS pin an external resistor divider from the other supply to ground (see the Applications Information section). 38901fa 11 LTC3890-1 OPERATION (Refer to the Functional Diagram) Light Load Current Operation (Burst Mode Operation, Pulse-Skipping, or Forced Continuous Mode) (PLLIN/MODE Pin) just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous operation. The LTC3890-1 can be enabled to enter high efficiency Burst Mode operation, constant frequency pulse-skipping mode, or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/ MODE pin to a DC voltage below 0.8V (e.g., SGND). To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulse-skipping mode, tie the PLLIN/MODE pin to a DC voltage greater than 1.2V and less than INTVCC - 1.3V. In forced continuous operation or clocked by an external clock source to use the phase-locked loop (see Frequency Selection and Phase-Locked Loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantage of lower output voltage ripple and less interference to audio circuitry. In forced continuous mode, the output ripple is independent of load current. When a controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 25% of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier, EA, will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. The ITH pin is then disconnected from the output of the EA and parked at 0.450V. In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current that the LTC3890-1 draws. If one channel is shut down and the other channel is in sleep mode, the LTC3890-1 draws only 50A of quiescent current. If both channels are in sleep mode, the LTC3890-1 draws only 60A of quiescent current. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA's output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator, IR, turns off the bottom external MOSFET When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC3890-1 operates in PWM pulse-skipping mode at light loads. In this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator, ICMP, may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. Frequency Selection and Phase-Locked Loop (FREQ and PLLIN/MODE Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3890-1's controllers can be selected using the FREQ pin. 38901fa 12 LTC3890-1 OPERATION (Refer to the Functional Diagram) If the PLLIN/MODE pin is not being driven by an external clock source, the FREQ pin can be tied to SGND, tied to INTVCC or programmed through an external resistor. Tying FREQ to SGND selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and SGND allows the frequency to be programmed between 50kHz and 900kHz, as shown in Figure 10. A phase-locked loop (PLL) is available on the LTC3890-1 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN/MODE pin. The LTC3890-1's phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of controller 1's external top MOSFET to the rising edge of the synchronizing signal. Thus, the turn-on of controller 2's external top MOSFET is 180 degrees out of phase to the rising edge of the external clock source. The VCO input voltage is prebiased to the operating frequency set by the FREQ pin before the external clock is applied. A resistor connected between the FREQ pin and SGND can prebias VCO's input voltage to the desired frequency. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock's to the rising edge of TG1. The ability to prebias the loop filter allows the PLL to lock-in rapidly without deviating far from the desired frequency. The typical capture range of the phase-locked loop is from approximately 55kHz to 1MHz, with a guarantee to be between 75kHz and 850kHz. In other words, the LTC3890-1's PLL is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. The typical input clock thresholds on the PLLIN/MODE pin are 1.6V (rising) and 1.2V (falling). Output Overvoltage Protection An overvoltage comparator guards against transient overshoots as well as other more serious conditions that may overvoltage the output. When the VFB pin rises by more than 10% above its regulation point of 0.800V, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. Power Good (PGOOD1 Pin) The PGOOD1 pin is connected to an open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD1 pin low when the corresponding VFB1 pin voltage is not within 10% of the 0.8V reference voltage. The PGOOD1 pin is also pulled low when the corresponding RUN1 pin is low (shut down). When the VFB1 pin voltage is within the 10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V. Foldback Current When the output voltage falls to less than 70% of its nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to the severity of the overcurrent or short-circuit condition. Foldback current limiting is disabled during the soft-start interval (as long as the VFB voltage is keeping up with the TRACK/SS voltage). Theory and Benefits of 2-Phase Operation Why the need for 2-phase operation? Up until the 2-phase family, constant-frequency dual switching regulators operated both channels in phase (i.e., single phase operation). This means that both switches turned on at the same time, causing current pulses of up to twice the amplitude of those for one regulator to be drawn from the input capacitor and battery. These large amplitude current pulses increased the total RMS current flowing from the input capacitor, requiring the use of more expensive input capacitors and increasing both EMI and losses in the input capacitor and battery. With 2-phase operation, the two channels of the dual switching regulator are operated 180 degrees out-of-phase. This effectively interleaves the current pulses drawn by the switches, greatly reducing the overlap time where they add 38901fa 13 LTC3890-1 OPERATION (Refer to the Functional Diagram) Figure 1 compares the input waveforms for a representative single-phase dual switching regulator to the LTC3890-1 2-phase dual switching regulator. An actual measurement of the RMS input current under these conditions shows that 2-phase operation dropped the input current from 2.53ARMS to 1.55ARMS. While this is an impressive reduction in itself, remember that the power losses are proportional to IRMS2, meaning that the actual power wasted is reduced by a factor of 2.66. The reduced input ripple voltage also means less power is lost in the input power path, which could include batteries, switches, trace/connector resistances and protection circuitry. Improvements in both conducted and radiated EMI also directly accrue as a result of the reduced RMS input current and voltage. the RMS input current varies for single phase and 2-phase operation for 3.3V and 5V regulators over a wide input voltage range. It can readily be seen that the advantages of 2-phase operation are not just limited to a narrow operating range, for most applications is that 2-phase operation will reduce the input capacitor requirement to that for just one channel operating at maximum current and 50% duty cycle. Of course, the improvement afforded by 2-phase operation is a function of the dual switching regulator's relative duty cycles which, in turn, are dependent upon the input voltage VIN (Duty Cycle = VOUT/VIN). Figure 2 shows how 3.0 SINGLE PHASE DUAL CONTROLLER 2.5 INPUT RMS CURRENT (A) together. The result is a significant reduction in total RMS input current, which in turn allows less expensive input capacitors to be used, reduces shielding requirements for EMI and improves real world operating efficiency. 2.0 1.5 2-PHASE DUAL CONTROLLER 1.0 0.5 0 VO1 = 5V/3A VO2 = 3.3V/3A 0 10 20 30 INPUT VOLTAGE (V) 40 38901 F02 Figure 2. RMS Input Current Comparison 5V SWITCH 20V/DIV 3.3V SWITCH 20V/DIV INPUT CURRENT 5A/DIV INPUT VOLTAGE 500mV/DIV IIN(MEAS) = 2.53ARMS IIN(MEAS) = 1.55ARMS 38901 F01 Figure 1. Input Waveforms Comparing Single-Phase (a) and 2-Phase (b) Operation for Dual Switching Regulators Converting 12V to 5V and 3.3V at 3A Each. The Reduced Input Ripple with the 2-Phase Regulator Allows Less Expensive Input Capacitors, Reduces Shielding Requirements for EMI and Improves Efficiency 38901fa 14 LTC3890-1 APPLICATIONS INFORMATION The Typical Application on the first page is a basic LTC3890-1 application circuit. LTC3890-1 can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption, and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs and Schottky diodes are selected. Finally, input and output capacitors are selected. SENSE+ and SENSE- Pins The SENSE+ and SENSE- pins are the inputs to the current comparators. The common mode voltage range on these pins is 0V to 28V (abs max), enabling the LTC3890-1 to regulate output voltages up to a nominal 24V (allowing margin for tolerances and transients). The SENSE+ pin is high impedance over the full common mode range, drawing at most 1A. This high impedance allows the current comparators to be used in inductor DCR sensing. The impedance of the SENSE- pin changes depending on the common mode voltage. When SENSE- is less than INTVCC - 0.5V, a small current of less than 1A flows out of the pin. When SENSE- is above INTVCC + 0.5V, a higher current (~700A) flows into the pin. Between INTVCC - 0.5V and INTVCC + 0.5V, the current transitions from the smaller current to the higher current. Filter components mutual to the sense lines should be placed close to the LTC3890-1, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 3). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If inductor DCR sensing is used (Figure 4b), sense resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. TO SENSE FILTER, NEXT TO THE CONTROLLER COUT 38901 F03 INDUCTOR OR RSENSE Figure 3. Sense Lines Placement with Inductor or Sense Resistor VIN INTVCC VIN BOOST TG RSENSE SW VOUT LTC3890-1 BG R1* SENSE+ SENSE- C1* PLACE CAPACITOR NEAR SENSE PINS SGND *R1 AND C1 ARE OPTIONAL. 38901 F04a (4a) Using a Resistor to Sense Current VIN INTVCC VIN BOOST INDUCTOR TG L DCR SW VOUT LTC3890-1 BG R1 SENSE+ C1* R2 SENSE- SGND *PLACE C1 NEAR SENSE PINS (R1||R2) t C1 = L DCR RSENSE(EQ) = DCR R2 R1 + R2 38901 F04b (4b) Using the Inductor DCR to Sense Current Figure 4. Current Sensing Methods 38901fa 15 LTC3890-1 APPLICATIONS INFORMATION Low Value Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 4a. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX). The current comparator threshold voltage sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, IL. To calculate the sense resistor value, use the equation: RSENSE = VSENSE(MAX) I IMAX + L 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the Maximum Current Sense Threshold (VSENSE(MAX)). When using the controller in very low dropout conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for buck regulators operating at greater than 50% duty factor. A curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak inductor current depending upon the operating duty factor. the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers' data sheets for detailed information. Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: RSENSE(EQUIV) = VSENSE(MAX) I IMAX + L 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the Maximum Current Sense Threshold (VSENSE(MAX)). Next, determine the DCR of the inductor. When provided, use the manufacturer's maximum value, usually given at 20C. Increase this value to account for the temperature coefficient of copper resistance, which is approximately 0.4%/C. A conservative value for TL(MAX) is 100C. To scale the maximum inductor DCR to the desired sense resistor value (RD), use the divider ratio: RD = RSENSE(EQUIV) DCRMAX at TL(MAX) Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3890-1 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 4b. The DCR of the inductor represents the small amount of DC resistance of the copper wire, which can be less than 1m for today's low value, high current inductors. In a high current application requiring such an inductor, power loss through a sense resistor would cost several points of efficiency compared to inductor DCR sensing. If the external (R1||R2) * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where C1 is usually selected to be in the range of 0.1F to 0.47F. This forces R1|| R2 to around 2k, reducing error that might have been caused by the SENSE+ pin's 1A current. The equivalent resistance R1|| R2 is scaled to the room temperature inductance and maximum DCR: R1|| R2 = L (DCR at 20C) * C1 The sense resistor values are: R1= R1|| R2 R1* RD ; R2 = 1- RD RD 38901fa 16 LTC3890-1 APPLICATIONS INFORMATION The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: PLOSS R1= ( VIN(MAX) - VOUT ) * VOUT R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET switching and gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current, IL, decreases with higher inductance or higher frequency and increases with higher VIN: IL = V 1 VOUT 1- OUT VIN ( f) (L) Accepting larger values of IL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is IL =0.3(IMAX). The maximum IL occurs at the maximum input voltage. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 25% of the current limit determined by RSENSE. Lower inductor values (higher IL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance value selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred for high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates hard, which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET and Schottky Diode (Optional) Selection Two external power MOSFETs must be selected for each controller in the LTC3890-1: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5.1V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. Pay close attention to the BVDSS specification for the MOSFETs as well. Selection criteria for the power MOSFETs include the on-resistance, RDS(ON), Miller capacitance, CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve 38901fa 17 LTC3890-1 APPLICATIONS INFORMATION usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the Gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN Synchronous Switch Duty Cycle = VIN - VOUT VIN The MOSFET power dissipations at maximum output current are given by: PMAIN = VOUT (IMAX )2 (1+ ) RDS(ON) + VIN I 2 ( VIN )2 MAX (RDR ) (CMILLER ) * 1 1 + ( f) VINTVCC - VTHMIN VTHMIN PSYNC = VIN - VOUT (IMAX )2 (1+ ) RDS(ON) VIN where is the temperature dependency of RDS(ON) and RDR (approximately 2) is the effective driver resistance at the MOSFET's Miller threshold voltage. VTHMIN is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The term (1+ ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but = 0.005/C can be used as an approximation for low voltage MOSFETs. The optional Schottky diodes D3 and D4 shown in Figure 11 conduct during the dead-time between the conduction of the two power MOSFETs. This prevents the body diode of the bottom MOSFET from turning on, storing charge during the dead-time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. CIN and COUT Selection The selection of CIN is simplified by the 2-phase architecture and its impact on the worst-case RMS current drawn through the input network (battery/fuse/capacitor). It can be shown that the worst-case capacitor RMS current occurs when only one controller is operating. The controller with the highest (VOUT)(IOUT) product needs to be used in the formula shown in Equation 1 to determine the maximum RMS capacitor current requirement. Increasing the output current drawn from the other controller will actually decrease the input RMS ripple current from its maximum value. The out-of-phase technique typically reduces the input capacitor's RMS ripple current by a factor of 30% to 70% when compared to a single phase power supply solution. In continuous mode, the source current of the top MOSFET is a square wave of duty cycle (VOUT)/(VIN). To prevent large voltage transients, a low ESR capacitor sized for the maximum RMS current of one channel must be used. The maximum RMS capacitor current is given by: CIN Required IRMS IMAX VIN ( V ) V - V 1/ 2 (1) OUT OUT IN ( ) This formula has a maximum at VIN = 2VOUT , where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not 38901fa 18 LTC3890-1 APPLICATIONS INFORMATION offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may be paralleled to meet size or height requirements in the design. Due to the high operating frequency of the LTC3890-1, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. The benefit of the LTC3890-1 2-phase operation can be calculated by using Equation 1 for the higher power controller and then calculating the loss that would have resulted if both controller channels switched on at the same time. The total RMS power lost is lower when both controllers are operating due to the reduced overlap of current pulses required through the input capacitor's ESR. This is why the input capacitor's requirement calculated above for the worst-case controller is adequate for the dual controller design. Also, the input protection fuse resistance, battery resistance, and PC board trace resistance losses are also reduced due to the reduced peak currents in a 2-phase system. The overall benefit of a multiphase design will only be fully realized when the source impedance of the power supply/battery is included in the efficiency testing. The drains of the top MOSFETs should be placed within 1cm of each other and share a common CIN(s). Separating the drains and CIN may produce undesirable voltage and current resonances at VIN. A small (0.1F to 1F) bypass capacitor between the chip VIN pin and ground, placed close to the LTC3890-1, is also suggested. A 10 resistor placed between CIN (C1) and the VIN pin provides further isolation between the two channels. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering. The output ripple (VOUT) is approximated by: 1 VOUT IL ESR + 8 * f * COUT where f is the operating frequency, COUT is the output capacitance and IL is the ripple current in the inductor. The output ripple is highest at maximum input voltage since IL increases with input voltage. Setting Output Voltage The LTC3890-1 output voltages are each set by an external feedback resistor divider carefully placed across the output, as shown in Figure 5. The regulated output voltage is determined by: R VOUT = 0.8V 1+ B RA To improve the frequency response, a feedforward capacitor, CFF , may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. VOUT 1/2 LTC3890-1 RB CFF VFB RA 38901 F05 Figure 5. Setting Output Voltage Tracking and Soft-Start (TRACK/SS Pins) The start-up of each VOUT is controlled by the voltage on the respective TRACK/SS pin. When the voltage on the TRACK/SS pin is less than the internal 0.8V reference, the LTC3890-1 regulates the VFB pin voltage to the voltage on the TRACK/SS pin instead of 0.8V. The TRACK/SS pin can be used to program an external soft-start function or to allow VOUT to track another supply during start-up. Soft-start is enabled by simply connecting a capacitor from the TRACK/SS pin to ground, as shown in Figure 6. An internal 1A current source charges the capacitor, providing a linear ramping voltage at the TRACK/SS pin. The LTC3890-1 will regulate the VFB pin (and hence VOUT) according to the voltage on the TRACK/SS pin, allowing VOUT to rise smoothly from 0V to its final regulated value. The total soft-start time will be approximately: tSS = CSS * 0.8V 1A 38901fa 19 LTC3890-1 APPLICATIONS INFORMATION 1/2 LTC3890-1 TRACK/SS VX(MASTER) SGND 38901 F06 Figure 6. Using the TRACK/SS Pin to Program Soft-Start OUTPUT VOLTAGE CSS Alternatively, the TRACK/SS pin can be used to track two (or more) supplies during start-up, as shown qualitatively in Figures 7a and 7b. To do this, a resistor divider should be connected from the master supply (VX) to the TRACK/ SS pin of the slave supply (VOUT), as shown in Figure 8. During start-up VOUT will track VX according to the ratio set by the resistor divider: For coincident tracking (VOUT = VX during start-up): 38901 F07a TIME (7a) Coincident Tracking VX(MASTER) OUTPUT VOLTAGE + RTRACKB R VX RA = * TRACKA VOUT RTRACKA RA + RB VOUT(SLAVE) VOUT(SLAVE) RA = RTRACKA RB = RTRACKB 38901 F07b INTVCC Regulators The LTC3890-1 features two separate internal P-channel low dropout linear regulators (LDO) that supply power at the INTVCC pin from either the VIN supply pin or the EXTVCC pin depending on the connection of the EXTVCC pin. INTVCC powers the gate drivers and much of the LTC3890-1's internal circuitry. The VIN LDO and the EXTVCC LDO regulate INTVCC to 5.1V. Each of these can supply a peak current of 50mA and must be bypassed to ground with a minimum of 4.7F ceramic capacitor. No matter what type of bulk capacitor is used, an additional 1F ceramic capacitor placed directly adjacent to the INTVCC and PGND IC pins is highly recommended. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. TIME (7b) Ratiometric Tracking Figure 7. Two Different Modes of Output Voltage Tracking Vx VOUT RB 1/2 LTC3890-1 VFB RA RTRACKB TRACK/SS RTRACKA 38901 F08 Figure 8. Using the TRACK/SS Pin for Tracking High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3890-1 to be exceeded. The INTVCC current, which is dominated by the gate charge current, may be supplied by either the VIN LDO or the EXTVCC LDO. When the voltage on the EXTVCC 38901fa 20 LTC3890-1 APPLICATIONS INFORMATION pin is less than 4.7V, the VIN LDO is enabled. Power dissipation for the IC in this case is highest and is equal to VIN * IINTVCC. The gate charge current is dependent on operating frequency as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3890-1 INTVCC current is limited to less than 15mA from a 40V supply when not using the EXTVCC supply at 70C ambient temperature: TJ = 70C + (15mA)(40V)(90C/W) = 125C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in forced continuous mode (PLLIN/MODE = INTVCC) at maximum VIN. When the voltage applied to EXTVCC rises above 4.7V, the VIN LDO is turned off and the EXTVCC LDO is enabled. The EXTVCC LDO remains on as long as the voltage applied to EXTVCC remains above 4.5V. The EXTVCC LDO attempts to regulate the INTVCC voltage to 5.1V, so while EXTVCC is less than 5.1V, the LDO is in dropout and the INTVCC voltage is approximately equal to EXTVCC. When EXTVCC is greater than 5.1V, up to an absolute maximum of 14V, INTVCC is regulated to 5.1V. Using the EXTVCC LDO allows the MOSFET driver and control power to be derived from one of the LTC3890-1's switching regulator outputs (4.7V VOUT 14V) during normal operation and from the VIN LDO when the output is out of regulation (e.g., start-up, short-circuit). If more current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the EXTVCC and INTVCC pins. In this case, do not apply more than 6V to the EXTVCC pin and make sure that EXTVCC VIN. Significant efficiency and thermal gains can be realized by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/(Switcher Efficiency). For 5V to 14V regulator outputs, this means connecting the EXTVCC pin directly to VOUT . Tying the EXTVCC pin to an 8.5V supply reduces the junction temperature in the previous example from 125C to: TJ = 70C + (15mA)(8.5V)(90C/W) = 82C However, for 3.3V and other low voltage outputs, additional circuitry is required to derive INTVCC power from the output. The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC Grounded. This will cause INTVCC to be powered from the internal 5.1V regulator resulting in an efficiency penalty of up to 10% at high input voltages. 2. EXTVCC Connected directly to VOUT . This is the normal connection for a 5V to 14V regulator and provides the highest efficiency. 3. EXTVCC Connected to an External supply. If an external supply is available in the 5V to 14V range, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. Ensure that EXTVCC < VIN. 4. EXTVCC Connected to an Output-Derived Boost Network. For 3.3V and other low voltage regulators, efficiency gains can still be realized by connecting EXTVCC to an output-derived voltage that has been boosted to greater than 4.7V. This can be done with the capacitive charge pump shown in Figure 9. Ensure that EXTVCC < VIN. CIN BAT85 VIN BAT85 MTOP NDS7002 TG1 1/2 LTC3890-1 EXTVCC L BAT85 RSENSE VOUT SW MBOT BG1 PGND D COUT 38901 F09 Figure 9. Capacitive Charge Pump for EXTVCC 38901fa 21 LTC3890-1 APPLICATIONS INFORMATION Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors, CB, connected to the BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though external diode DB from INTVCC when the SW pin is low. When one of the topside MOSFETs is to be turned on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the top MOSFET switch and turns it on. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC. The value of the boost capacitor, CB, needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). The external diode DB can be a Schottky diode or silicon diode, but in either case it should have low-leakage and fast recovery. Pay close attention to the reverse leakage current specification for this diode, especially at high temperatures where it generally increases substantially. For applications with output voltages greater than ~5V that are switching infrequently, a leaky diode DB can fully discharge the bootstrap capacitor CB, creating a current path from the output voltage to the BOOST pin to INTVCC. Not only does this increase the quiescent current of the converter, but it can cause INTVCC to rise to dangerous levels if the leakage exceeds the current consumption on INTVCC. Particularly, this is a concern in Burst Mode operation at no load or very light loads, where the part is switching very infrequently and the current draw on INTVCC is very low (typically about 35A). Generally, pulse-skipping and forced continuous modes are less sensitive to leakage, since the more frequent switching keeps the bootstrap capacitor CB charged, preventing a current path from the output voltage to INTVCC. However, in cases where the converter has been operating (in any mode) and then is shut down, if the leakage of diode DB fully discharges the bootstrap capacitor CB before the output voltage discharges to below ~5V, then the leakage current path can be created from the output voltage to INTVCC. In shutdown, the INTVCC pin is able to sink about 30A. To accommodate diode leakage greater than this amount in shutdown, INTVCC can be loaded with an external resistor or clamped with a Zener diode. Alternatively, the PGOOD resistor can be used to sink the current (assuming the resistor pulls up to INTVCC) since PGOOD is pulled low when the converter is shut down. Nonetheless, using a low-leakage diode is the best choice to maintain low quiescent current under all conditions. Fault Conditions: Current Limit and Current Foldback The LTC3890-1 includes current foldback to help limit load current when the output is shorted to ground. If the output voltage falls below 70% of its nominal output level, then the maximum sense voltage is progressively lowered from 100% to 45% of its maximum selected value. Under short-circuit conditions with very low duty cycles, the LTC3890-1 will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The short-circuit ripple current is determined by the minimum on-time. tON(MIN), of the LTC3890-1 (90ns), the input voltage and inductor value: V IL(SC) = tON(MIN) IN L The resulting average short-circuit current is: 1 ISC = 45% * ILIM(MAX) - IL(SC) 2 Fault Conditions: Overvoltage Protection (Crowbar) The overvoltage crowbar is designed to blow a system input fuse when the output voltage of the regulator rises much higher than nominal levels. The crowbar causes huge currents to flow, that blow the fuse to protect against a shorted top MOSFET if the short occurs while the controller is operating. A comparator monitors the output for overvoltage conditions. The comparator detects faults greater than 10% above the nominal output voltage. When this condition is sensed, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. The bottom MOSFET remains on continuously for as long as the overvoltage condition persists; if VOUT returns to a safe level, normal operation automatically resumes. 38901fa 22 LTC3890-1 APPLICATIONS INFORMATION 1000 A shorted top MOSFET will result in a high current condition which will open the system fuse. The switching regulator will regulate properly with a leaky top MOSFET by altering the duty cycle to accommodate the leakage. 900 FREQUENCY (kHz) 800 Phase-Locked Loop and Frequency Synchronization The LTC3890-1 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a lowpass filter, and a voltage-controlled oscillator (VCO). This allows the turn-on of the top MOSFET of controller 1 to be locked to the rising edge of an external clock signal applied to the PLLIN/MODE pin. The turn-on of controller 2's top MOSFET is thus 180 degrees out of phase with the external clock. The phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. If the external clock frequency is greater than the internal oscillator's frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP, holds the voltage at the VCO input. Note that the LTC3890-1 can only be synchronized to an external clock whose frequency is within range of the LTC3890-1's internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. Typically, the external clock (on the PLLIN/MODE pin) input high threshold is 1.6V, while the input low threshold is 1.1V. Rapid phase locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO's input voltage is prebiased at a frequency corresponding to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase lock and synchronization. Although it is not required that the free-running 700 600 500 400 300 200 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (k) 38901 F10 Figure 10. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. Table 2 summarizes the different states in which the FREQ pin can be used. Table 2 FREQ PIN PLLIN/MODE PIN FREQUENCY 0V DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor DC Voltage 50kHz to 900kHz Any of the Above External Clock Phase-Locked to External Clock Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3890-1 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN) < VOUT VIN ( f) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. 38901fa 23 LTC3890-1 APPLICATIONS INFORMATION The minimum on-time for the LTC3890-1 is approximately 90ns. However, as the peak sense voltage decreases the minimum on-time gradually increases up to about TBDns. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3890-1 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) topside MOSFET transition losses. 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. Supplying INTVCC from an output-derived source power through EXTVCC will scale the VIN current required for the driver and control circuits by a factor of (Duty Cycle)/ (Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 2.5mA of VIN current. This reduces the midcurrent loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 3. I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is chopped between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON) = 30m, RL = 50m, RSENSE = 10m and RESR = 40m (sum of both input and output capacitance losses), then the total resistance is 130m. This results in losses ranging from 3% to 13% as the output current increases from 1A to 5A for a 5V output, or a 4% to 20% loss for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4. Transition losses apply only to the topside MOSFET(s), and become significant only when operating at high input voltages (typically 15V or greater). Transition losses can be estimated from: Transition Loss = (1.7) * VIN * 2 * IO(MAX) * CRSS * f Other hidden losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these system level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20F to 40F of capacitance having a maximum of 20m to 50m of ESR. The LTC3890-1 2-phase architecture typically halves this 38901fa 24 LTC3890-1 APPLICATIONS INFORMATION input capacitance requirement over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD (ESR), where ESR is the effective series resistance of COUT . ILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in Figure 13 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT , causing a rapid drop in VOUT . No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. Design Example As a design example for one channel, assume VIN = 12V(nominal), VIN = 22V (max), VOUT = 3.3V, IMAX = 5A, VSENSE(MAX) = 75mV and f = 350kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the FREQ pin to GND, generating 350kHz operation. The minimum inductance for 30% ripple current is: IL = VOUT V 1- OUT ( f) (L) VIN(NOM) 38901fa 25 LTC3890-1 APPLICATIONS INFORMATION A 4.7H inductor will produce 29% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 5.73A. Increasing the ripple current will also help ensure that the minimum on-time of 95ns is not violated. The minimum on-time occurs at maximum VIN: VOUT 3.3V tON(MIN) = = = 429ns VIN(MAX) ( f) 22V (350kHz ) CIN is chosen for an RMS current rating of at least 3A at temperature assuming only this channel is on. COUT is chosen with an ESR of 0.02 for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: The equivalent RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (43mV): When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 11. Figure 12 illustrates the current waveforms present in the various branches of the 2-phase synchronous regulators operating in the continuous mode. Check the following in your layout: RSENSE 64mV 0.01 5.73A Choosing 1% resistors: RA = 25k and RB = 78.7k yields an output voltage of 3.32V. The power dissipation on the topside MOSFET can be easily estimated. Choosing a Fairchild FDS6982S dual MOSFET results in: RDS(ON) = 0.035/0.022, CMILLER = 215pF. At maximum input voltage with T(estimated) = 50C: 3.3V PMAIN = (5A )2 1+ (0.005) (50C - 25C) 22V 5A (0.035) + (22V )2 (2.5) (215pF ) * 2 1 1 + (350kHz ) = 331mW 5V - 2.3V 2.3V A short-circuit to ground will result in a folded back current of: ISC = 34mV 1 95ns (22V ) - = 3.18A 0.01 2 4.7H with a typical value of RDS(ON) and = (0.005/C)(25C) = 0.125. The resulting power dissipated in the bottom MOSFET is: VORIPPLE = RESR (IL) = 0.02(1.45A) = 29mVP-P PC Board Layout Checklist 1. Are the top N-channel MOSFETs MTOP1 and MTOP2 located within 1cm of each other with a common drain connection at CIN? Do not attempt to split the input decoupling for the two channels as it can cause a large resonant loop. 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (-) terminals. The path formed by the top N-channel MOSFET, Schottky diode and the CIN capacitor should have short leads and PC trace lengths. The output capacitor (-) terminals should be connected as close as possible to the (-) terminals of the input capacitor by placing the capacitors next to each other and away from the Schottky loop described above. 3. Do the LTC3890-1 VFB pins' resistive dividers connect to the (+) terminals of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 2 PSYNC = (3.18A ) (1.125) (0.022) = 250mW which is less than under full-load conditions. 38901fa 26 LTC3890-1 APPLICATIONS INFORMATION 4. Are the SENSE- and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE- should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the SENSE resistor. 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pins? This capacitor carries the MOSFET drivers' current peaks. An additional 1F ceramic capacitor placed immediately next to the INTVCC and PGND pins can help improve noise performance substantially. 6. Keep the switching nodes (SW1, SW2), top gate nodes (TG1, TG2), and boost nodes (BOOST1, BOOST2) away from sensitive small-signal nodes, especially from the opposites channel's voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and therefore should be kept on the output side of the LTC3890-1 and occupy minimum PC trace area. 7. Use a modified star ground technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC. PC Board Layout Debugging Start with one controller on at a time. It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold-- typically 25% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Only after each controller is checked for its individual performance should both controllers be turned on at the same time. A particularly difficult region of operation is when one controller channel is nearing its current comparator trip point when the other channel is turning on its top MOSFET. This occurs around 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. An embarrassing problem, which can be missed in an otherwise properly working switching regulator, results when the current sensing leads are hooked up backwards. The output voltage under this improper hookup will still be maintained but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor--don't worry, the regulator will still maintain control of the output voltage. 38901fa 27 LTC3890-1 APPLICATIONS INFORMATION ITH1 TRACK/SS1 VFB1 PGOOD1 RPU1 VPULL-UP PGOOD1 L1 R1* + SENSE1 C1* RSENSE VOUT1 TG1 SW1 SENSE1- LTC3890-1 BOOST1 CB1 M1 M2 D1* BG1 FREQ fIN RIN PLLIN/MODE VIN CVIN RUN1 1F CERAMIC COUT1 + PGND RUN2 EXTVCC SGND - SENSE2 CINTVCC INTVCC BG2 R2* VFB2 BOOST2 ITH2 SW2 TRACK/SS2 VIN M3 + CIN COUT2 1F CERAMIC C2* SENSE2+ GND + M4 D2* CB2 RSENSE TG2 VOUT2 L2 38901 F11 *R1, R2, C1, C2, D1, D2 ARE OPTIONAL. Figure 11. Recommended Printed Circuit Layout Diagram 38901fa 28 LTC3890-1 APPLICATIONS INFORMATION SW1 L1 D1 RSENSE1 VOUT1 COUT1 RL1 VIN RIN CIN SW2 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. D2 L2 RSENSE2 VOUT2 COUT2 RL2 38901 F12 Figure 12. Branch Current Waveforms 38901fa 29 LTC3890-1 TYPICAL APPLICATIONS SENSE1+ C1 1nF RB1 100k INTVCC 100k - SENSE1 RA1 31.6k PGOOD1 VFB1 CITH1A 100pF BG1 RITH1 34.8k CITH1 1000pF MBOT1 SW1 BOOST1 ITH1 CB1 0.1F LTC3890-1 CSS1 0.01F L1 4.7H TRACK/SS1 TG1 RSENSE1 8m VOUT1 3.3V 5A COUT1 470F MTOP1 D1 VIN PLLIN/MODE SGND EXTVCC RUN1 RUN2 FREQ VOUT2 RFREQ 41.2k INTVCC CINT 4.7F PGND D2 TG2 CSS2 0.01F MTOP2 CB2 0.1F TRACK/SS2 RITH2 34.8k CITH2 470pF VIN 9V TO 60V CIN 220F L2 8H BOOST2 RSENSE2 10m VOUT2 8.5V 3A SW2 ITH2 COUT2 330F RA2 10.5k VFB2 RB2 100k MBOT2 BG2 SENSE2- C2 1nF SENSE2+ 38901 TA02a MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB L1: COILCRAFT SER1360-472KL L2: COILCRAFT SER1360-802KL COUT1: SANYO 6TPE470M COUT2: SANYO 10TPE330M D1, D2: DFLS1100 Figure 13. High Efficiency Dual 8.5V/3.3V Step-Down Converter Efficiency and Power Loss vs Output Current Efficiency vs Load Current 10000 VIN = 12V 90 VOUT = 3.3V BURST EFFICIENCY 90 1000 CCM LOSS 100 60 50 40 PULSE-SKIPPING LOSS BURST LOSS 10 30 20 10 0 0.0001 CCM EFFICIENCY PULSE-SKIPPING EFFICIENCY 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 1 0.1 10 38901 TA02b EEFICIENCY (%) 70 80 POWER LOSS (mW) EEFICIENCY (%) 80 100 VOUT = 8.5V 98 VOUT = 3.3V 60 50 40 30 94 92 90 VOUT1 = 3.3V 88 86 20 84 10 82 VIN = 12V 0 0.0001 0.001 0.01 0.1 1 OUTPUT CURRENT (A) VOUT2 = 8.5V 96 70 EEFICIENCY (%) 100 Efficiency vs Input Voltage 100 10 38901 TA02c ILOAD = 2A 80 0 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) 38901 TA02d 38901fa 30 LTC3890-1 TYPICAL APPLICATIONS High Efficiency 8.5V Dual-Phase Step-Down Converter SENSE1+ RB1 100k C1 1nF RA1 10.5k SENSE1- INTVCC 100k PGOOD1 VFB1 MBOT1 CITH1A 100pF BG1 L1 8H VOUT1 8.5V 6A SW1 RITH1 34.8k CITH1 C SS1 0.01F 470pF RSENSE1 10m BOOST1 ITH1 TRACK/SS1 COUT1 330F CB1 0.1F LTC3890-1 TG1 MTOP1 D1 INTVCC RMODE 100k VIN CIN 9V TO 60V 220F VIN PLLIN/MODE INTVCC CINT 4.7F SGND VIN RRUN V 1000k OUT EXTVCC RUN1 RUN2 FREQ RFREQ 41.2k PGND D2 TG2 BOOST2 ITH2 VFB2 MTOP2 CB2 0.1F TRACK/SS2 CITH2 100pF L2 8H RSENSE2 10m SW2 BG2 COUT2 330F MBOT2 SENSE2- C2 1nF SENSE2+ 38901 TA03 MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB L1, L2: COILCRAFT SER1360-802KL COUT1, COUT2: SANYO 10TPE330M D1, D2: DFLS1100 38901fa 31 LTC3890-1 TYPICAL APPLICATIONS High Efficiency Dual 12V/5V Step-Down Converter SENSE1+ RB1 100k C1 1nF RA1 6.98k SENSE1- INTVCC 100k PGOOD1 VFB1 CITH1A 100pF CITH1 470pF BG1 RITH1 34.8k MBOT1 SW1 TRACK/SS1 COUT1 180F VOUT1 12V 3A CB1 0.47F LTC3890-1 CSS1 0.01F L1 8H BOOST1 ITH1 RSENSE1 9m TG1 MTOP1 D1 VIN PLLIN/MODE SGND EXTVCC RUN1 RUN2 FREQ RFREQ 41.2k INTVCC VIN 12.5V TO 60V CINT 4.7F PGND D2 TG2 MTOP2 CB2 0.47F CSS2 0.01F TRACK/SS2 CITH2 470pF CIN 220F RITH2 20k BOOST2 L2 4.7H RSENSE2 10m VOUT2 5V 5A COUT2 470F SW2 ITH2 BG2 MBOT2 RA2 18.7k VFB2 SENSE2- RB2 100k C2 1nF SENSE2+ 38901 TA04 MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB L1: COILCRAFT SER1360-802KL L2: COILCRAFT SER1360-472KL COUT1: 16SVP180MX COUT2: SANYO 6TPE470M D1, D2: DFLS1100 38901fa 32 LTC3890-1 TYPICAL APPLICATIONS High Efficiency Dual 24V/5V Step-Down Converter RB1 487k SENSE1+ C1 1nF CF1 33pF RA1 16.9k 100k PGOOD1 VFB1 CITH1A 100pF CITH1 680pF SENSE1- INTVCC BG1 RITH1 46k MBOT1 L1 22H RSENSE1 25m VOUT1 24V 1A SW1 BOOST1 ITH1 CSS1 0.01F TRACK/SS1 COUT1 22F x2 CERAMIC CB1 0.47F LTC3890-1 TG1 MTOP1 D1 VIN PLLIN/MODE SGND EXTVCC RUN1 RUN2 FREQ RFREQ 60k INTVCC VIN 28V TO 60V CINT 4.7F PGND D2 TG2 MTOP2 CB2 0.47F CSS2 0.01F CITH2 470pF CIN 220F TRACK/SS2 RITH2 20k BOOST2 L2 4.7H RSENSE2 10m VOUT2 5V 5A SW2 ITH2 BG2 RA2 18.7k COUT2 470F MBOT2 VFB2 RB2 100k SENSE2- C2 1nF SENSE2+ 38901 TA05 MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB L1: SUMIDA CDR7D43MN L2: COILCRAFT SER1360-472KL COUT1: KEMET T525D476MO16E035 COUT2: SANYO 6TPE470M D1, D2: DFLS1100 38901fa 33 LTC3890-1 PACKAGE DESCRIPTION GN Package 28-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .386 - .393* (9.804 - 9.982) .045 p.005 28 27 26 25 24 23 22 21 20 19 18 17 1615 .254 MIN .033 (0.838) REF .150 - .165 .229 - .244 (5.817 - 6.198) .0165 p.0015 .150 - .157** (3.810 - 3.988) .0250 BSC 1 RECOMMENDED SOLDER PAD LAYOUT .015 p .004 s 45o (0.38 p 0.10) .0075 - .0098 (0.19 - 0.25) 2 3 4 5 6 7 8 .0532 - .0688 (1.35 - 1.75) 9 10 11 12 13 14 .004 - .0098 (0.102 - 0.249) 0o - 8o TYP .016 - .050 (0.406 - 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 - .012 (0.203 - 0.305) TYP .0250 (0.635) BSC GN28 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 38901fa 34 LTC3890-1 REVISION HISTORY REV DATE DESCRIPTION A 01/11 Added MP-grade and H-grade. Changes reflected throughout the data sheet. PAGE NUMBER 1-38 38901fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 35 LTC3890-1 TYPICAL APPLICATION High Efficiency Dual 12V/3.3V Step-Down Converter SENSE1+ C1 1nF RB1 100k RA1 6.98k SENSE1- INTVCC 100k PGOOD1 VFB1 CITH1A 100pF BG1 RITH1 34.8k CITH1 470pF MBOT1 SW1 L1 8H BOOST1 ITH1 TRACK/SS1 COUT1 180F VOUT1 12V 3A CB1 0.47F LTC3890-1 CSS1 0.01F RSENSE1 9m TG1 MTOP1 D1 VIN PLLIN/MODE SGND VOUT1 RFREQ 41.2k EXTVCC RUN1 RUN2 FREQ INTVCC VIN 12.5V TO 60V CINT 4.7F PGND D2 TG2 MTOP2 CB2 0.47F CSS2 0.01F TRACK/SS2 RITH2 34.8k CITH2 1000pF CIN 220F BOOST2 L2 4.7H RSENSE2 10m SW2 ITH2 CITH2A 100pF BG2 MBOT2 VOUT2 3.3V 5A COUT2 470F VFB2 RA2 31.6k SENSE2- RB2 100k C2 1nF MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB L1: COILCRAFT SER1360-802KL L2: COILCRAFT SER1360-472KL COUT1: 16SVP180MX COUT2: SANYO 6TPE470M D1, D2: DFLS1100 SENSE2+ 38901 TA06 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT3891 60V, Low IQ, Synchronous Step-Down DC/DC Controller PLL Fixed Frequency 50kHz to 900kHz, 4V VIN 60V, 0.8V VOUT 24V, TSSOP-20E, 3mm x 4mm QFN-20 LTC3857/LTC3857-1/ LTC3858/LTC3858-1 Low IQ, Dual Output 2-Phase Synchronous Step-Down DC/DC Controllers with 99% Duty Cycle PLL Fixed Frequency 50kHz to 900kHz, 4V VIN 38V, 0.8V VOUT 24V, IQ = 50A/170A LTC3834/LTC3834-1/ LTC3835/LTC3835-1 Low IQ, Single Output Synchronous Step-Down DC/DC Controllers with 99% Duty Cycle PLL Fixed Frequency 140kHz to 650kHz, 4V VIN 36V, 0.8V VOUT 10V, IQ = 30A/80A LTC3810 100V Synchronous Step-Down DC/DC Controller Constant On-Time Valley Current Mode, 4V VIN 100V, 0.8V VOUT 0.93VIN, SSOP-28 LTC3859 Low IQ, Triple Output Buck/Buck/Boost Synchronous DC/DC Controller Outputs (5V) Remain in Regulation Through Cold Crank, 2.5V VIN 38V, VOUT(BUCK) Up to 24V, VOUT(BOOST) Up to 60V 38901fa 36 Linear Technology Corporation LT 0111 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2010