Instruction Sheet 408-10424 Circular Light Module (CN88) 28 JAN 11 Rev A 2. DESCRIPTION Top Ring This module consists of a base with mounting hardware, Bridgelux LED, PCBA with thermal protection, Thermal Interface Material (TIM), protection cover, reflector with multiple beam angle configurations (narrow and wide), and a snap-on top ring. The module is available in several configurations. See Figure 1. Compression Ring Reflector 3. ASSEMBLY PROCEDURE NOTE i The module must be assembled by a qualified electrician in accordance with national and local electrical codes and the following instructions. Protection Cover 3.1. Heat Sink Mounting NOTE PCBA i The thermal management of the overall system is critical to the life of the LED. It is very important that the thermal management is adequate for the LED lighting fixture being used. For more detailed information, refer to Application Specification 114-13300. Figure 2 shows a properly sized heat sink mounting pattern. For low volume production applications of the CN88, TE offers a Transfer Punch Guide (part number 2154454-1) to assist in the making of the heat sink mounting hole drill locations. See Figure 2. Screws and Washers Base 31 Connector Keep-Out Zone (O 88.00 Ref) Bridgelux LED Thermal Interface Material M3 O 0.10 (4x) 5 Figure 1 1. INTRODUCTION The circular Light Module (CN88), (part number 2154159-[ ]), is designed as a compact, selfcontained, easy-to-mount, plug-and-play circular module to be used in both prototype and custom production applications. This module is to be used with the NEVALO* Interconnect System (refer to Tyco Electronics (TE) Application Specification 114-13290). The module can be used with the Straight and Right-Angle NEVALO Connectors. NOTE i All numerical are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless otherwise specified, dimensions have a tolerance of 0.13 and angles have a tolerance of 2. Figures and illustrations are for identification only and not drawn to scale. Bridgelux is a trademark. O 2.50 0.05 O 0.10 (2x) 38.3 66 Transfer Punch Alignment Pin Locations Screw Locations OBSOLETE Clamp Area NOT the LATEST REVISION Center of Light Module Figure 2 (c)2011 Tyco Electronics Corporation, Berwyn, PA TOOLING ASSISTANCE CENTER 1-800-722-1111 All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names might be trademarks of their respective owners. This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 3 LOC B 408-10424 Thermal Interface Material Clear Protective Layer Figure 3 3.2. Mounting the Circular Light Module (CN88) 1. Once the heat sink has been properly sized and prepared for the application of the Circular Light Module (CN88), the base sub-assembly (base housing, screws, protection cover, PCBA, LED, and TIM) can be aligned over the mounting holes. Mounting screws to be alternately tightened to a torque of 0.28 to 0.45 Nm [2.5 to 4.0 in.-lbf]. See Figure 3. The protective cover can now be removed. Specification 114-13290 for information on assembly procedures on the NEVALO Interconnect System. CAUTION When mounting the module, care must be taken not to damage the light module and LEDs with the screwdriver used for tightening the mounting ! screws. The protection cover is protecting the LED during this operation. CAUTION If the clear protective layer on the TIM material is not removed, optimum thermal performance will not be achieved. ! 2. The reflector is then installed, aligning three keyways. Reflector posts have a slight click-fit into the light engine holes. Firmly seat the optic in place. See Figure 4. CAUTION TE recommends that when handling the reflector, that non-marking gloves be used. The reflector should be handled by the outer diameter to ! eliminate the chance of leaving marks within the light emitting area. 3. The top ring (with compression ring pre-assembled) is then lowered over the light module, aligning three (3) pegs in the top ring to three (3) guide features in the base. With a slight downward pressure (to compress the compression ring and a clockwise twist), you will feel and hear a tactile and audible click. This secures the top ring on the Circular Light Module (CN88) and completes the assembly. See Figure 5. Refer to Application Rev A Figure 4 2 of 3 408-10424 4. After the Circular Light Module (CN88) is secured to the heat sink, the mating NEVALO Cable Assembly can be mated to energize the module. The Circular Light Module (CN88) will accept the Straight and Right-Angle NEVALO Connectors. Straight is shown in Figure 6. Figure 6 4. REPLACEMENT AND REPAIR CAUTION Circular Light Module (CN88) components are not repairable. If it is evident that a component is damaged, it must be removed and replaced with a ! new component. Order products through your local Tyco Electronics Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 5. REVISION SUMMARY Figure 5 Rev A * Initial release of document 3 of 3