December 2013
Common Mode Filters
For high-speed differential signal line
(USB2.0, LVDS, etc.)
MCZ-AH series
MCZ0806AH [0302 inch]*
MCZ1210AH [0504 inch]
MCZ2010AH [0804 inch]
* Dimensions Code JIS[EIA]
EMC Components
(2/11)
001-01 / 20131227 / e9712_mcz_ah.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
Common Mode Filters
For high-speed differential signal line
(USB2.0, LVDS, etc.)
FEATURES
Compact multilayer common mode filter.
Has EMC suppression by achieving wide frequency range differential mode transmission while ensuring common mode impedance
with virtually no affect on the high-speed differential transmission line signal.
APPLICATION
Electronic equipment high-speed interface (LVDS, USB2.0, MHL)
Mobile phones, PCs, DSCs, portable game machines, etc.
PDP/LCD/DLP/PJ TVs, DVD players, DVCs, mobile audio, etc.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Overview of the MCZ-AH Series
MCZ 1210 AH 360 L2 T
Series name L×W×T Dimensions Product internal
code
Impedance Number of lines Packaging style
(mm) (:) at 100MHz
0806 0.85×0.65×0.45 AH 360 36 L2 2 lines T Taping
1210 1.25×1.0×0.5 L4 4 lines
2010 2.0×1.0×0.5
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C） （pieces/reel） （mg）
MCZ0806AH –40 to +85 –40 to +85 10,000 1.4
MCZ1210AH –40 to +85 –40 to +85 4,000 3.0
MCZ2010AH –40 to +85 –40 to +85 5,000 5.0
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
Overview of the MCZ-AH Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series
MCZ0806AH Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
0.85±0.05
0.5±0.10
0.65±0.05
0.45±0.05
0.27±0.10
43
12
Dimensions in mm
0.20
0.30
0.30
0.30
43
12
•
No polarity
(6/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series MCZ0806AH Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
[100MHz]
DC resistance
(:)max.
[1 line]
Rated current
(mA)max.
Rated voltage
(V)max.
Insulation
resistance
(M:)min.
Part No.
(:)Tolerance
22 ±8:1.5 100 5 10 MCZ0806AH220L2T
35 ±25% 2.5 100 510 MCZ0806AH350L2T
50 ±25% 3.0 100 5 10 MCZ0806AH500L2T
90 ±25% 4.0 100 510 MCZ0806AH900L2T
Measurement item Product No. Manufacturer
Common mode impedance E4991A+16192A Agilent Technologies
DC resistance Type-7561 Yokogawa
Insulation resistance 4339B Agilent Technologies
Product No. Manufacturer
E4991A+16192A Agilent Technologies
1 10 100 1000 10000
10000
1000
100
1
10
Impedance (Ω)
Frequency (MHz)
900 Common mode
500 Common mode
900 Differential mode
500 Differential mode
350 Common mode
220 Common mode
350 Differential mode
220 Differential mode
(7/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series
MCZ1210AH Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
1.0±0.15
0.55±0.1
1.25±0.15
0.5±0.1
0.3±0.1
43
12
Dimensions in mm
0.25
0.7 to 0.75
0.3
0.5
43
12
•
No polarity
(8/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series MCZ1210AH Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
[100MHz]
DC resistance
(:)max.
[1 line]
Rated current
(mA)max.
Rated voltage
(V)max.
Insulation
resistance
(M:)min.
Part No.
(:)Tolerance
36 ±25% 1.00 200 5 10 MCZ1210AH360L2T
90 ±25% 1.75 100 510 MCZ1210AH900L2T
200 ±25% 4.00 100 5 10 MCZ1210AH201L2T
300 ±25% 4.50 100 510 MCZ1210AH301L2T
Measurement item Product No. Manufacturer
Common mode impedance E4991A+16192A Agilent Technologies
DC resistance Type-7561 Yokogawa
Insulation resistance 4339B Agilent Technologies
Product No. Manufacturer
E4991A+16192A Agilent Technologies
1 10 100 1000 10000
10000
1000
100
1
10
Impedance (Ω)
Frequency (MHz)
301 Common mode
201 Common mode
301 Differential mode
201 Differential mode
900 Common mode
360 Common mode
900 Differential mode
360 Differential mode
(9/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series
MCZ2010AH Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
0.5±0.1 1.0±0.15
2.0±0.15
0.5±0.1
0.25±0.1
0.2±0.15
1234
8765
Dimensions in mm
1.8
0.6
0.25
0.5
Dimensions in mm
1234
8765
•
No polarity
(10/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series MCZ2010AH Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
[100MHz]
DC resistance
(:)max.
[1 line]
Rated current
(mA)max.
Rated voltage
(V)max.
Insulation
resistance
(M:)min.
Part No.
(:)Tolerance
90 ±25% 1.50 100 5 10 MCZ2010AH900L4T
120 ±25% 2.00 100 510 MCZ2010AH121L4T
200 ±25% 3.50 100 5 10 MCZ2010AH201L4T
Measurement item Product No. Manufacturer
Common mode impedance E4991A+16192A Agilent Technologies
DC resistance Type-7561 Yokogawa
Insulation resistance 4339B Agilent Technologies
Product No. Manufacturer
E4991A+16192A Agilent Technologies
1 10 100 1000 10000
10000
1000
100
1
10
Impedance (Ω)
Frequency (MHz)
201 Common mode
201 Differential mode
121 Common mode
900 Common mode
900 Differential mode
121 Differential mode
(11/11)
001-01 / 20131227 / e9712_mcz_ah.fm
• All specifications are subject to change without notice.
EMC Components
MCZ-AH series
Packaging style
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Type A B P1 K t
MCZ0806AH 0.75±0.05 0.95±0.05 2.0±0.05 0.6max. 0.25±0.05
MCZ1210AH 1.15±0.1 1.4±0.1 4.0±0.1 1.0max. 0.25±0.05
MCZ2010AH 1.15±0.05 2.15±0.05 4.0±0.1 0.86max. —
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
8.0±0.3
3.5±0.05
1.75±0.1
4.0±0.12.0±0.05
B
A P1
1.5 +0.1
0
MCZ0806
MCZ1210MCZ2010
K
t
K
160min. Taping 200min.
300min.
Drawing direction Dimensions in mm
