Keysight Technologies
Analog channels 2 or 4 2 or 4 2 or 4 2 or 4
Digital channels (MSO) 16 16 16 8
Bandwidth (upgradable) 1, 2.5, 4, 6 GHz 200, 350, 500 MHz, 1, 1.5 GHz 100, 200, 350, 500 MHz, 1 GHz 70, 100, 200 MHz
Max sampling rate 20 GSa/s 5 GSa/s
5 GSa/s (1 GHz)
2 GSa/s
Max memory depth 4 Mpts 4 Mpts 2 Mpts (standard)
4 Mpts (option)
100 kpts (standard)
1 Mpts (option)
Max waveform update rate > 450,000 waveforms/sec > 1,000,000 waveforms/sec > 1,000,000 waveforms/sec > 50,000 waveforms/sec
Display 12.1 inches, capacitive,
multi-touch, gesture enabled
12.1 inches, capacitive 8.5 inches 8.5 inches
Standard Standard No No
Voice control Standard No No No
20-MHz function/arbitrary
waveform generator
Dual-channel AWG (option) Dual-channel AWG (option) Single-channel AWG (option) Single-channel function (option)
Integrated digital voltmeter Option Option Option Option
Integrated hardware counter 5 digits (standard),
10 digits + totalizer (option)
5 digits (standard) 5 digits (standard) 5 digits (standard)
Search and navigate Standard with lister Standard Standard Standard
Segment memory Standard Standard Option Option
Mask/limit test Option Option Option Option
Serial protocol analysis options I2C/SPI, UART, CAN/LIN,
FlexRay, I2S, MIL-STD1553/
ARINC429, USB 2.0
I2C/SPI, UART, CAN/LIN,
FlexRay, I2S, MIL-STD1553/
ARINC429, USB 2.0
I2C/SPI, UART, CAN/LIN,
FlexRay, I2S, MIL-STD1553/
ARINC429
I2C/SPI, UART, CAN/LIN (will
not operate simultaneously with
digital channels)
Advanced analysis options Power analysis, USB 2.0 signal
quality test, HDTV analysis,
FPGA
Power analysis, USB 2.0 signal
quality test, HDTV analysis,
FPGA
Power analysis, HDTV analysis No
Color grade Standard No No No
Histogram Standard No No No
FFT Standard enhanced FFT Standard Standard Standard
Jitter analysis Option No No No
Real-time eye diagram Option No No No
Advanced math Standard, display four functions
simultaneously
Standard, display one function Option, display one function No
Connectivity Standard USB 2.0, LAN, video
(GPIB option), USB mouse and
keyboard support
Standard USB 2.0, LAN, video
(GPIB option), USB mouse and
keyboard support
Standard USB 2.0 (LAN/video/
GPIB option), USB keyboard
support
Standard USB 2.0 (LAN/video/
GPIB option), USB keyboard
support
Data TIE
Eye height
Hardware bandwidth
20 MHz, 200 MHz
20 MHz, 200 MHz,
1.5 GHz*, 3 GHz**
1 Hz through bandwidth
of scope
2.1-inch capacitive
multi-touch screen with gesture support sets
urn off the
touch screen.
6-in-1 instrument
Fully upgradable
histogram on a
Jitter and real-time eye diagram analysis
Dual-channel WaveGen
Both
6 GHz upgradable bandwidth
signal quality analysis
FPGA dynamic probe.
Four AutoProbes
450,000 waveforms per second update
Multi-language voice control
Transparent
four
functions simultaneously
10 measurements
gating by cursors
integrated digital voltmeter
and 10-digit counter with totalizer.
Input channels DSOX6002A 2
DSOX6004A 4
MSOX6002A 2 + 16
MSOX6004A 4 + 16
Bandwidth options 1 GHz 2.5 GHz 4 GHz 6 GHz
For 2 channel models Default DSOX6B10T252BW DSOX6B10T402BW DSOX6B10T602BW
For 4 channel modes Default DSOX6B10T254BW DSOX6B10T404BW DSOX6B10T604BW
* Examples
Application Bundle
Softare application bundle DSOX6APPBNDL (includes DSOX6EMBD, DSOX6COMP, DSOX6USBFL,
DSOX6USBH, DSOX6AUTO, DSOX6FLEX, DSOX6AUDIO, DSOX6AERO,
DSOX6JITTER, DSOX6WAVEGEN2, DSOXDVMCTR, DSOX6PWR, DSOX6MASK,
DSOX6USBSQ, DSOX6VID, DSOX6FPGAX, DSOXEDK)
Embedded serial triggering and analysis (I²C, SPI) (SPI requires 4, 2+16, or
4+16 channel 6000 X-Series)
DSOX6EMBD
Computer serial triggering and analysis (RS232/UART) DSOX6COMP
USB 2.0 full-/low-speed serial decode and triggering DSOX6USBFL
USB 2.0 hi-speed serial decode and triggering DSOX6USBH
Automotive serial triggering and analysis (CAN/LIN) DSOX6AUTO
FlexRay serial triggering and analysis DSOX6FLEX
Audio serial triggering and analysis (I²S) DSOX6AUDIO
MIL-STD 1553 and ARINC 429 serial triggering and analysis DSOX6AERO
Dual-channel WaveGen 20-MHz AWG DSOX6WAVEGEN2
Jitter and real-time eye diagram analysis DSOX6JITTER
Integrated digital voltmeter and 10-digit counter DSOXDVMCTR
Power analysis application DSOX6PWR
Mask limit testing DSOX6MASK
USB 2.0 signal quality test DSOX6USBSQ
Enhanced video/TV application package DSOX6VID
FPGA dynamic probe option for Xilinx DSOX6FPGAX
Education and training kit DSOXEDK
N8900A
BenchVue 34840B
Included standard; 1 per channel
N2756A 16 digital channel MSO cable Included standard on MSOX models and DSOX6MSO
Optional
10076B high-voltage passive probe (4 kV) Optional
Optional
Optional
N2797A active single-ended probe 1.5 GHz, extreme temperature Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
1147B AC/DC current probe, 50 MHz, 15 A with AutoProbe Optional
N2893A AC/DC current probe, 100 MHz, 15 A with AutoProbe Optional
N2820A 2-channel high-sensitivity current probe, 50 uA - 5 A Optional
N2821A 1-channel high-sensitivity current probe, 50 uA - 5 A Optional
GPIB connection module N4865A
Rack mount kit N2111A
Soft carrying case N2733B
Hard copy manual N2112A
Hard transit case (Available from CPD Industries (www.casecruzer.com)) 3A1311-2710J
DSOX6B10T252BW
DSOX6B10T402BW
DSOX6B10T602BW
DSOX6B25T402BW
DSOX6B25T602BW
DSOX6B40T602BW
DSOX6B10T254BW
DSOX6B10T404BW
DSOX6B10T604BW
DSOX6B25T404BW
DSOX6B25T604BW
DSOX6B40T604BW
DSOX6MSO
Half-channel bandwidth* (-3 dB) 1 GHz 2.5 GHz 4 GHz 6 GHz
Full-channel bandwidth* (-3 dB) 1 GHz 2.5 GHz 4 GHz 4 GHz
Calculated rise time (10-90%)
Input channels DSOX6002A 2
DSOX6004A 4
MSOX6002A 2 + 16
MSOX6004A 4 + 16
Maximum sample rate 20 GSa/s half channel, 10 GSa/s all channel
Maximum memory depth Standard 4 Mpts, standard segmented memory
Display size and type 12.1-inch capacitive multi-touch/gesture-enabled display
Waveform update rate > 450,000 waveforms per second
Hardware bandwidth
limits
20 MHz, 200 MHz (selectable per channel)
20 MHz, 200 MHz, 1.5 GHz, 3 GHz (selectable per channel)
Input coupling AC, DC
Input impedance
Input sensitivity range
1 mV/div to 1 V/div**
Vertical resolution 8 bits (measurement resolution is 12 bits with averaging)
Maximum input voltage 300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk
Frequency derating (assumes sine wave input): 400 Vpk until 40 kHz
Then derates at 20 db/dec until 6 Vpk
DC vertical gain accuracy* ± 3 div: 1.5% (typical)
± 4 div: 2.5% (warranted)**
DC vertical offset accuracy ± 0.1 div ± 2 mV ± 1% of offset setting
Channel-to-channel isolation
Offset range ± 5 V (1 to < 10 mV/div), ± 20 V (10 to 200 mV/div), ± 100 V ( > 200 mV/div)
± 12 div or ± 4 V, whichever is smallest (> 100 mV/div)
Dynamic range ± 8 divisions from center screen ( 100 mV/div), 2nd harmonic distortion of - 40 dbc
± 4 divisions from center screen (> 101 mV/div), 2nd harmonic distortion of - 23 dbc
± 8 divisions from center screen
1 GHz 2.5 GHz 4 GHz 6 GHz
1 mV/div 115 µVrms 150 µVrms 150 µVrms 210 µVrms
10 mV/div 330 µVrms 355 µVrms 350 µVrms 395 µVrms
100 mV/div 3.15 mVms 3.25 mVms 3.20 mVms 3.35 mVms
1 V/div 31.5 mVms 32.5 mVms 32 mVms 33.5 mVms
ESD tolerance ± 2 kV (on input BNCs)
Digital input channels 16 digital (D0 to D15. Pod 1: D7 ~ D0, Pod 2: D15 ~ D8)
Thresholds Threshold per pod
Threshold selections
± 8.0 V in 10-mV steps
Maximum input voltage ± 40 V peak; transient overvoltage 800 Vpk
Threshold accuracy* ± (100 mV + 3% of threshold setting)
Maximum input dynamic range ± 10 V about threshold
Minimum voltage swing 500 mVpp
Input impedance
Input capacitance ~8 pF
Vertical resolution 1 bit
1 GHz 2.5 GHz 4 GHz 6 GHz
Time base range 500 ps/div to 50 s/div 200 ps/div to 50 s/div 100 ps/div to 50 s/div
Time base accuracy* ± 1.6 ppm + aging factor
(1 year: ± 0.5 ppm, 2 years: ± 0.7 ppm, 5 years: ± 1.5 ppm, 10 years: ± 2.0 ppm)
Time base resolution 2.5 ps
Time base delay time
range
Pre-trigger Greater of 1 screen width or 50 µs
Post-trigger 1 s to 500 s
Channel-to-channel deskew range ± 100 ns
Same channel: ± (time base accuracy x reading) ± (0.0016 x screen width) ± 10 ps
Channel-to-channel: ± (time base accuracy x reading) ± (0.0016 x screen width) ± 15 ps
Modes Main, zoom, roll, XY
XY
Bandwidth: maximum bandwidth. Phase error at 1 MHz: < 0.5 degree
Minimum detectable pulse width 2 ns
Channel-to-channel skew 2 ns (typical); 3 ns (maximum)
Maximum analog channels sample rate 20 GSa/s half channel interleaved, 10 GSa/s all channel
Analog channels equivalent sample rate 400 GSa/s
Maximum analog chan-
nels record length
4 Mpts half channel interleaved, 2 Mpts all channel
> 2 GSa/s 1 Mpts half channel interleaved, 500 kpts all channel
Maximum digital channels sample rate 2 GSa/s half pods interleaved, 1 GSa/s all pods
Maximum digital channels record length 4 Mpts half pods interleaved, 2 Mpts all pods
Acquisition mode Normal Default mode
Peak detect Analog channels: capture glitches as narrow as 500 ps (half channel), 1 ns (all channel)
Digital channels: capture glitches as narrow as 500 ps (half pods), 1 ns (all pods)
Averaging Selectable from 2, 4, 8, 16, 64, ... to 65,536
High resolution Real-time boxcar averaging reduces random noise and effectively increases vertical resolution
Segmented Segmented memory optimizes available memory for data streams that have long dead times be-
trigger events)
Data acquisition mode Real time Default mode (> 135,000 waveforms/sec)
Max update rate Enhanced real-time mode for the fastest waveform update rate of > 450,000 waveforms/sec.
Up to 2 GSa/s. Returns to a normal real-time mode at > 2 GSa/s
Equivalent -
tive sample rate of 400 GSa/s
Time mode Normal Default mode
Roll Displays the waveform moving across the screen from right to left. Available at time bases 50 ms/div
or slower
XY Shows the volts-versus-volts display. Time base can be set from 200 ns/div to 50 ms/div
Trigger sources Analog channel (1~4), digital channel (D0~D15), line, external, WaveGen (1, 2, or Mod (FM/FSK))
Trigger modes Normal Requires trigger event for oscilloscope to trigger
Auto Triggers automatically but not synchronized to the input in absence of trigger event
Single Front panel button that triggers only once on a trigger event. Press Single button again for oscillo-
Auto or Normal mode
Force Front panel button forces a synchronous trigger
Trigger coupling DC DC-coupled trigger
AC AC-coupled trigger, cutoff frequency: < 10 Hz (internal); <50 Hz (external)
HF reject High-frequency reject, cutoff frequency ~ 50 kHz
LF reject Low-frequency reject, cutoff frequency ~ 50 kHz
Noise reject Adds hysteresis to the trigger circuitry; selectable OFF or ON, decreases sensitivity 2x
Trigger holdoff range 40 ns to 10.00 s
Trigger jitter < 1.0-ps rms with the jitter-free trigger
< 3.0-ps rms without the jitter-free trigger
Trigger bandwidth Edge 500 MHz, 1 GHz, 2.5 GHz models: bandwidth of oscilloscope. 4-GHz and 6-GHz models: 3.5 GHz
Other modes Bandwidth of oscilloscope or 1 GHz, whichever is smaller
Trigger sensitivity
(internal)*
1 GHz bandwidth < 10 mV/div DC to 1 GHz Greater of 1 div or 5 mVpp
DC to 1 GHz 0.6 div
2.5, 4, and 6 GHz
bandwidth
< 10 mV/div DC to 2 GHz Greater of 1 div or 5 mVpp
2.0 to 3.5 GHz Greater of 1.5 div or 5 mVpp
DC to 2 GHz 0.6 div
2.0 to 3.5 GHz 1.0 div
Trigger sensitivity
(external)*
± 1.6 V 40 mVpp DC to 100 MHz, 70 mVpp 100 MHz to 200 MHz
± 8 V 200 mVpp DC to 100 MHz, 350 mVpp 100 MHz to 200 MHz
Trigger level range Any channel ± 6 div from center screen
External 8-V range = ± 8 V; 1.6-V range = ± 1.6 V
Specify zones as either “must intersect” or “must not intersect.” Up to two zones.
> 160,000 wfm/sec update rate
Supported modes: normal, peak detect, high resolution, max update rate
Also works simultaneously with the serial decodes and mask/limit test
Edge Trigger on a rising and falling edge of any source, alternating or either edge of analog and digital
channels
Edge then edge (B trigger)
edge. Minimum 4 ns
Pulse width Trigger on a pulse on a selected channel, whose time duration is less than a value, greater than a
value, or inside a time range
Minimum duration setting: 2 ns
Maximum duration setting: 10 s
Range minimum: 10 ns
Pattern
digital, or trigger channels is [entered | exited]. Pattern must have stabilized for a minimum of 2 ns to
qualify as a valid trigger condition
Minimum duration setting: 2 ns
Maximum duration setting: 10 s
Or Trigger on any selected edges from available sources (analog and digital channels only).
Bandwidth is 500 MHz
Rise/fall time Trigger on rise time or fall time edge speed violations (< or >) based on user-selectable threshold. Select from
(< or >) and time settings range between
Minimum: 1 ns
Maximum: 10 s
Nth edge burst Trigger on the nth (1 to 65535) edge of a pulse burst. Specify idle time (10 ns to 10 s) for framing
Runt Trigger on a position runt pulse that fails to exceed a high-level threshold. Trigger on a negative runt pulse that
fails to drop below a low-level threshold. Trigger on either polarity runt pulse based on two threshold settings.
Setup and hold Trigger on setup/hold violations. Setup time can be set from -7 s to 10 s. Hold time can be set from 0 s to 10 ns.
Minimum window (setup time + hold time) must be 3 ns or greater
Video
(NTSC, PAL, SECAM, PAM-M)
Enhanced video (HDTV) (Option)
1080p/25, 1080p/30, 1080p/50, 1080p/60, 1080i/50, 1080i/60)
ARINC429 (Option) Trigger and decode on ARINC429 data. Trigger on word start/stop, label, label + bits, label range, error
conditions (parity, word, gap, word or gap, all), all bits (eye), all 0 bits, all 1 bits
CAN (Option) Trigger on CAN (controller area network) version 2.0A and 2.0B signals. Trigger on the start of frame (SOF) bit,
remote frame ID (RTR), data frame ID (~RTR), remote or data frame ID, data frame ID and data, error frame, all
FlexRay (Option)
I²C (Option)
acknowledge, address with no acq, restart, EEPROM read, and 10-bit write
I²S (Option)
decreasing value)
LIN (Option) Trigger on LIN (Local Interconnect Network) sync break, sync frame ID, frame ID and data , parity error, or
checksum error
MIL-S TD15 53 (Opt ion) Trigger on MIL-STD 1553 signals on data word start/stop, command/status start/stop, RTA, RTA + 11 bits, and
error conditions (parity, sync, Manchester)
SPI (Option)
Supports MOSI and MISO data
UART/RS232/422/485 (Option) Trigger on Rx or Tx start bit, stop bit, data content, or parity error
USB (Option) Trigger on start of packet (SOP), end of packet (EOP), suspend***, resume***, reset***, packets (token, data,
handshake, or special), and errors (PID, CRC5, CRC16, glitch, bit stuff***, SE1***). Supports USB 2.0 low-
Type Edge, pulse width, rise/fall, runt, frequency peak, serial bus 1, serial bus 2
Copy Copy to trigger, copy from trigger
Frequency peak Source Math functions
Max number of peaks 11
Control Threshold, excursion, results order (frequency or amplitude)
Result display Event lister or navigation. Manual or autoscroll via navigation or touch event lister entry to jump to a
DC vertical accuracy/cursors** Single cursor accuracy: ± [DC vertical gain accuracy + DC vertical offset accuracy + 0.21% full scale]
Dual cursor accuracy: ± [DC vertical gain accuracy + 0.42% full scale]*
Number of measurements 56 automatic measurements, maximum of 10 displayed at a time
Cursors 2 pairs of XY cursors
Automatic measure-
ments
Measurements continuously updated with statistics. Cursors track last selected measurement.
Select up to 10 measurements from the list below:
Snapshot Makes a snapshot of 31 most popular measurements. Touchable target to populate the measurement
side bar
Voltage/current Peak-to-peak, maximum, minimum, amplitude, top, base, overshoot, preshoot, average- N cycles,
average-full screen, DC RMS-N cycles, DC RMS-full screen, AC RMS-N cycles, AC RMS-full screen
(standard deviation), ratio-N cycles, ratio-full screen
Time Period, frequency, counter, + width, - width, burst width, + duty cycle, - duty cycle, rise time, fall
time, delay, phase, X at min Y, X at max Y
Count Positive pulse count, negative pulse count, rising edge count, falling edge count
Mixed Area-N cycles, area-full screen
Jitter Option DSOX6JITTER required
Data TIE, clock TIE, N-period, period-period, + width to + width, - width to - width
Real-time eye Option DSOX6JITTER required
Eye width, eye height
Dual-channel (requires
N2820A probe)
Charge-N cycles, charge-full screen, peak-peak, amplitude, DC RMS-N cycles, DC RMS-full screen,
AC RMS- N cycles, AC RMS-full screen (standard deviation), average-N cycles, average-full screen,
base
Counter Built-in frequency counter (see “Precision counter/totalizer section” for the 10-digit counter)
Source Any analog and digital channel
Resolution 5 digits
Max frequency 1 GHz (1.2 GHz typical)
Number of math functions Four, displays all four simultaneously. Can be cascaded
Arithmetic Add, subtract, multiply, divide, differentiate, integrate, FFT, Ax + B, squared, square root, absolute
(timing or state), clock recovery
Enhanced FFT Record size Up to 1-Mpts resolution via precision mode
Window types
Display Color grade or monochrome
Waveforms FFT, max hold, min hold, average
Peak search Max 11 peaks, threshold and excursion control
Mask/limit test (Option) Standard mask/limit test capability provides pass/fail comparison of a signal under test to a
template can be made via a text editor. > 130,000 mask tests per second (waveform update rate)
Histogram Provides a statistical view of a waveform or a measurement
Source Any analog channels, math functions, reference waveforms, measurements
Types Horizontal, vertical, or measurement
Measurements Hits, peak, max, min, peak to peak, mean, median, mode, bin width, standard deviation, 1~3 sigma
Modes
Color grade Provides a 3-dimensional view of waveform intensity
Source Any analog channels, math functions, reference waveforms, real-time eye
Color themes Temperature and intensity
Modes
Jitter (Option) Measures the variance of a measurement over time
Jitter measurement
600 fs rms at 6 GHz sine wave (typical)
Source Any analog channels, math functions, and reference waveforms
Clock recovery
Data rate: fully automatic, semi-automatic, manual
Real-time eye (Option) Provides the color graded eye pattern analysis based on the recovered clock. Data bits are folded
on top of each other per clock cycle to give a 3-dimensional view
Source Any analog channels, math functions, and reference waveforms
Clock recovery
Data rate: fully automatic, semi-automatic, manual
Color mode Color grade
Measurements Eye height, eye width
Precision mode Increase the analysis record length. Minimum: 100 kpts; maximum 1 Mpts
Counter Source
Resolution
Max frequency Up to 3.2 GHz (4 GHz typical). With Hi-speed USB 2.0 decoding, 1 GHz (1.2 GHz typical)
Trig-qual events
Measurement Frequency, period, totalize
Totalizer Counter size 64-bit totalizing counter
Edge Rise or fall
Gating Positive or negative level. Select from analog channels except the source
Time reference Internal or external 10 MHz reference clock
Source Analog channels only (1 ~ 4)
Functions ACrms, DC, DCrms, frequency
Resolution ACV/DCV: 3 digits
Counter frequency: 5.5 digits
Measuring rate 100 times/second
Auto ranging
Range meter Graphical display of most recent measurement, plus extreme over the previous 3 seconds
WaveGen outputs Two (front-panel BNC connectors)
Both waveform generator outputs can be frequency tracked, amplitude tracked, or completely tracked.*
Waveforms Sine, square, ramp, pulse, DC, noise, sine cardinal (sinc), exponential rise, exponential fall, cardiac, Gaussian pulse, and
arbitrary
Modulation Modulation is available on channel 1 only. Modulation is not available when tracking mode is enabled
Modulation types: AM, FM, FSK
Carrier waveforms: sine, ramp, sine cardinal, exponential rise, exponential fall, and Cardiac.C176
Modulation source: Internal (no external modulation capability)
AM:
Modulation: sine, square, ramp
Modulation frequency: 1 Hz to 20 kHz
Depth: 0% to 100%
FM:
Modulation: sine, square, ramp
Modulation frequency: 1 Hz to 20 kHz
Minimum carrier frequency: 10 Hz
Deviation: 1 Hz to carrier frequency or (2e12/carrier frequency), whichever is smaller
FSK:
Modulation: 50% duty cycle square wave
FSK rate: 1 Hz to 20 kHz|
Hop frequency: 2x FSK rate to 10 MHz
Sine Frequency range: 0.1 Hz to 20 MHz
± 0.5 dB (relative to 1 kHz)
Harmonic distortion: –40 dBc
Spurious (nonharmonics): –40 dBc
Total harmonic distortion: 1%
Square wave/pulse Frequency range: 0.1 Hz to 10 MHz
Duty cycle: 20 to 80%
Duty cycle resolution: Larger of 1% or 10 ns
Rise/fall time: 19 ns (10 to 90%)
Overshoot: < 2%
Asymmetry (at 50% DC): ± 1% ± 5ns
Jitter (TIE RMS): 500 ps
Ramp/triangle wave Frequency range: 0.1 Hz to 200 kHz
Linearity: 1%
Variable symmetry: 0 to 100%
Symmetry resolution: 1%
Pulse Frequency range: 0.1 Hz to 10 MHz
Pulse width 20 ns minimum
Pulse with resolution: 10 ns
Edge time: Fixed at 19 ns (not variable)
Overshoot: < 2%
Noise Bandwidth: 20 MHz typical
Sine cardinal (sinc) Frequency range: 0.1 Hz to 1.0 MHz
Exponential rise/fall Frequency range: 0.1 Hz to 5.0 MHz
Cardiac Frequency range: 0.1 Hz to 200.0 kHz
Gaussian pulse Frequency range: 0.1 Hz to 5.0 MHz
Arbitrary Waveform length: 1 to 8,192 points
Amplitude resolution: 10 bits (including sign bit)**
Repetition rate: 0.1 Hz to 12 MHz
Sample rate: 100 MSa/s
Filter bandwidth: 20 MHz
Frequency Sine wave and ramp accuracy: 130 ppm (frequency < 10 kHz)
50 ppm (frequency > 10 kHz)
Square wave and pulse accuracy: [50 + frequency/200] ppm (frequency < 25 kHz)
Resolution: 0.1 Hz or 4 digits, whichever is larger
Amplitude Range: minimum
Range: maximum
Resolution:
Accuracy: 1.5% (frequency = 1 kHz)
DC offset Range:
Resolution: Larger of 250 uV or 3 digits
Accuracy (waveform modes): ± 1.5% of offset setting ± 1% of amplitude ± 1 mV
Accuracy (DC mode): ± 1.5% of offset setting ± 3 mV
Main output Impedance :
Isolation: Not available, main output BNC is grounded
Protection: Overload automatically disables output
Trigger output Trigger output available on trig-out BNC
Quick Measure All Displays a popup containing a snapshot of all the single waveform measurements
Quick Measure Statistics Reset Resets all measurement statistics and the measurement count
Quick Mask Statistics Reset Resets mask statistics and counters
Quick Histogram Statistics Reset
Quick Print Print the current screen image
Quick Save
Quick Email
Quick Recall Recalls setup, mask, or reference waveform
Quick Freeze Display Freezes the display without stopping running acquisitions or unfreezes the display if currently frozen.
Waveform intensity preserved
Quick Trigger Mode Toggles the trigger mode between auto and normal
Quick Clear Display Clears the display
Display 12.1-inch, capacitive multi-touch/gesture-enabled display
Display mode
Resolution 800 (H) x 600 (V) pixel format (screen area)
Graticules 8 vertical divisions by 10 horizontal divisions with intensity controls
Format YT and XY
Maximum waveform update rate > 135,000 wfm/s (real time)
> 450,000 wfm/s (real time max update rate)
Persistence
Intensity gradation 256 intensity levels
USB 2.0 hi-speed host port USB 2.0 hi-speed host ports x3, two front and one real panel. Supports memory devices, printers, keyboards, mice,
and USB microphones
USB 2.0 hi-speed device port One USB 2.0 hi-speed device port on rear panel. USB Test & Measurement Class (USBTMC) compatible
LAN port 10/100/1000 Base-T port on rear panel. LXI IPv6 extended function
Web remote control VNC Web interface (via major Web browsers)
Video-out port VGA out on rear panel. Connect oscilloscope display to an external monitor or projector
GPIB port N4865A GPIB-to-LAN adapter (option)
10-MHz reference BNC connector on the rear panel
Support mode Output and input off, output on (10-MHz out) input on (10-MHz in)
In mode
Recommended input signal accuracy: better than ± 10 ppm
Out mode
Trigger out BNC connector on the rear panel. Supported modes: triggers, mask, waveform generator 1 sync pulse, and waveform
generator 2 sync pulse
Power line consumption Maximum 200 watts
Power voltage range 100-120 V, 50/60/400 Hz; 100-240 V, 50/60 Hz ± 10% auto ranging
Temperature Operating: 0 to +50 °C
Non-operating: –40 to +70 °C
Humidity Operating: 90% RH (non-condensing) at 40 °C
Non-operating: 90% RH (non-condensing) at 65 °C
Altitude Operating: Up to 4,000 m (15,000 ft.)
Non-operating: Up to 15,300 m (50,000 ft.)
Electromagnetic compatibility Meets EMC Directive (2004/108/EC), meets or exceeds IEC 61326-1:2005/EN
61326-1:2006 Group 1 Class A requirement
CISPR 11/EN 55011
IEC 61000-4-2/EN 61000-4-2
IEC 61000-4-3/EN 61000-4-3
IEC 61000-4-4/EN 61000-4-4
IEC 61000-4-5/EN 61000-4-5
IEC 61000-4-6/EN 61000-4-6
IEC 61000-4-11/EN 61000-4-11
Canada: ICES-001:2004
Safety UL61010-1 3rd edition, CAN/CSA_22.2 No. 61016-1-12, IEC61010-1 3rd edition
Vibration Meets IEC60068-2-6 and MIL-PRF-28800; class 3 random
Shock Meets IEC 60068-2-27 and MIL-PRF-28800; class 3 random; (operating 30 g, ½ sine,
11-ms duration, 3 shocks/axis along major axis, total of 18 shocks)
Mean Time Before Failure (MTBF) > 120,000 hours
Dimensions 425 mm W x 288 mm H x 148 mm D
Weight Net: 6.8 kg (15 lbs.), Shipping: 11.3 kg (25 lbs.)
Reference waveform display Four internal waveforms or USB thumb drive. Displays up to 4 reference waveforms simultaneously
Setup/image Setup (*.scp), 8 or 24-bit bitmap image (*.bmp), PNG 24-bit image (*.png)
Waveform data CSV data (*.csv), ASCII XY data (*.csv), binary data (*.bin), lister data (*.csv), reference waveform
data (*.h5), multichannel waveform data (*.h5), arbitrary waveform data (*.csv)
Application data Mask (*.msk), power harmonics data (*.csv), USB signal quality (*.html and *.bmp)
Analysis results (*.csv) Cursor data, measurement results, histogram statistics, mask test statistics, color grade bin,
search, segmented timestamps
10 internal setups
Limited by size of USB drive
Factory warranty 3-year warranty (90 days for unserialized accessories such as passive probes)
Calibration
Probe
One per channel, N2894A 700-MHz passive probe (10:1 attenuation)
N2756A 16-digital-channel MSO cable (1 per oscilloscope included on all MSO models and
DSOX6MSO upgrade option)
Interface language support/built-in help
Russian, and Spanish localized front-panel overlays, interface, and built-in help system
Voice control support
Italian, Japanese, Korean, Portuguese, Russian, Spanish (Latin America) and Spanish (Castilian)
Power cord Localized power cord
Front-panel protection Front-panel cover
Documentation
Product Fact Sheet 5991-4273EN
Application Note 5991-4000EN
Evaluating Oscilloscopes for Low-Power Measurements Application Note 5991-4268EN
Revolutionary Probing Technology in Current Probes to Make Low-power Measurements Application Note 5991-4375EN
Application Note 5991-4167EN
Application Note 5991-4038EN
Italy
myKeysight
www.keysight.com/find/mykeysight
www.axiestandard.org
®
®®
www.lxistandard.org
www.pxisa.org
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
www.keysight.com/go/quality
Keysight Channel Partners
www.keysight.com/find/channelpartners
