EAO – Your Expert Partner for
Human Machine Interfaces
EAO Product Information
Series 51
51
Switches and Indicators
51
Contents
2
01.2010
Description......................................................................................................3
Product Assembly ..........................................................................................4
Devices raised mounting ...............................................................................7
Devices flush mounting ...............................................................................13
Accessories...................................................................................................21
Technical Data...............................................................................................33
Typical Applications.....................................................................................36
Application guidelines..................................................................................37
Marking..........................................................................................................38
Drawings........................................................................................................40
Index...............................................................................................................58
3
01.2010
51
Description
General notes
The illuminated pushbuttons of series 51 with hoseproof front (IP 65)
can be supplied with snap-action or low-level switching elements. The
equipment (switches) for raised mounting are protected against
accidental operation by the extended sides of the bezel. Flush mounting
equipment excells with best available ergonomy and low down hight.
To supplement the range of illuminated pushbuttons, we can offer a
hoseproof safety keylock switch with various lock numbers.
Mounting
All switch actuators are mounted from the front by pushing them through
the mounting hole in the front panel. They are then fixed from the back
with a fixing nut and the mounting tool Typ-Nr. 01-907. Max. tightening
torque 50 Ncm.
For switching elements we offer plug-in bases, which when soldered to
a PCB enable a plug-in connection to the button. The rectangular
actuators for raised are provided with an anti-twisting device.
Lenses
The flat or concave lenses are available in various colours, as well as
translucent or transparent. Round lenses for flush mounting equipment
are available in aluminium also.
Because of production related reasons, the colours of anodized
aluminium parts can vary slightly.
Marking
For further information about engraving, hot stamping and film inserts
see part Marking.
Illumination
The T1 3/4 Midget Groove incandescent (filament) lamp (6 ... 48 V)
ensures perfect illumination of the lenses, which are supplied in various
colours.
T1 3/4 Midget Groove Single-LED (6, 12, 24, 28, 48 V) are also available
in blue, green, red, white or yellow.
Luminosity and wave length scattering caused by technologie used in
the LED manufacturing processes may lead to visual differences in our
products.
For supply voltages above 48 V, it is necessary to use a voltage
reduction element (external series resistor or transformer).
Position indication
The status of a maintained action switch can be determinded by the
position of the lens.
Keylock switch
Standard lock (Index D). Standard lock number is 311. If the lock
number is not specified, we will supply standard number 311.
An additional 134 special locks (Index X) are available on request.
Master keys for lock numbers 311 ... 445 may be ordered by quoting
Typ-Nr. 31-989.300. Two keys are supplied with each keylock switch.
Spare keys (Index D) for standard locks may be ordered by quot ing
Typ-Nr. 31-989.xxx (please state the lock number).
Specimen order
0
We reserve the right to modify technical data
All dimensions in mm
Product Information Indicator :
- Indicator actuator, 18 x 24 mm, soldering
terminal 31-040.005
Essential accessories :
- Lens plastic blue, transparent, flush,
18 x 24 mm 31-903.6
- Single-LED, T1 3/4 MG, 24 VAC/DC, blau 10-2J12.1066
51
Product Assembly
4
01.2010
Indicator round, raised mounting
01 Lens
2LED
3 Indicator housing
4 Sealing
5 Front plate
6 Fixing nut
Illuminated pushbutton, raised mounting
01 Lens
2LED
3 Switch housing
4 Sealing
5 Front plate
6 Fixing nut
1
2
3
4
5
6
1
2
3
4
5
6
51
Product Assembly
5
01.2010
Keylock switch round, flush mounting
01 Actuator housing
2 Front bezel
3 Sealing
4 Front plate
5 Anti-twist ring
6 Thrust piece
7 Fixing nut
8 Switching element
1
2
3
4
5
7
6
8
51
Product Assembly
6
01.2010
Selector switch square, flush mounting
01 Actuator housing
2LED
3 Actuator housing
4 Front bezel
5 Sealing
6 Front plate
7 Fixing bracket
8 Fixing nut
1
2
3
4
5
7
6
8
51
Devices raised mounting
7
01.2010
Essential Accessories:
d Lens plastic, raised mounting page 21
d Single-LED page 30
Continuation see next page
Indicators fit also in mounting hole n o . 2
Diode (1N 4007): D = Diode, - = without
Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Indicator actuator
Front protection
Diode (1N 4007)
Terminals
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Indicator actuator IP 65 1 D UT 51-703.006 51-701.006 51-741.006 4 1 12 78 0.006
2 D UT 51-704.006 51-702.006 51-742.006 4 1 12 79 0.006
-S51-050.005 51-040.005 51-030.005 1 12 1 0.004
S1 51-050.002 51-040.002 51-030.002 1 12 1 0.004
UT 51-051.006 51-041.006 51-031.006 41121 0.005
51
Devices raised mounting
8
01.2010
Essential Accessories:
d Lens plastic, raised mounting page 21
d Single-LED page 30
Continuation see next page
Illuminated pushbutton fit also in mounting hole no. 2
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Diode (1N 4007): - = without, D = Diode
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, H = Combined terminal: Solder-/ Universal (at contact/ at diode), S = Soldering terminal, S1 = Soldering
terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Illuminated pushbutton actuator
Front protection
Switching system
Contacts
Diode (1N 4007)
Switching action
Terminals
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Illuminated
pushbutton actuator IP 65 LL 1 NC - MA UT 51-486.036 51-466.036 51-476.036 4113110.007
MUT51-456.036 51-426.036 51-436.036 4113570.007
1 NC + 1 NO - MA UT 51-483.036 51-463.036 51-473.036 4113140.007
MUT51-453.036 51-423.036 51-433.036 4113600.007
1 NO - MA UT 51-485.036 51-465.036 51-475.036 4113130.007
MUT51-455.036 51-425.036 51-435.036 4113590.007
2 NC - MA UT 51-482.036 51-462.036 51-472.036 4113120.007
MUT51-452.036 51-422.036 51-432.036 4113580.007
2 NO - MA UT 51-481.036 51-461.036 51-471.036 4113150.007
MUT51-451.036 51-421.036 51-431.036 4113610.007
SA 1 NC + 1 NO 1 D MA H 51-717.0292 51-713.0292 51-747.0292 1 13 8 0.008
MH51-709.0292 51-705.0292 51-743.0292 1 13 54 0.008
2 D MA H 51-718.0292 51-714.0292 51-748.0292 1 13 9 0.008
MH51-710.0292 51-706.0292 51-744.0292 1 13 55 0.008
-MAS51-281.0252 51-261.0252 51-271.0252 1 13 10 0.006
S1 51-281.022 51-261.022 51-271.022 1 13 7 0.006
MS51-151.0252 51-121.0252 51-131.0252 1 13 56 0.006
S1 51-151.022 51-121.022 51-131.022 1 13 53 0.006
2 NC + 2 NO 1 D MA H 51-719.0292 51-715.0292 51-749.0292 1 13 4 0.010
MH51-711.0292 51-707.0292 51-745.0292 1 13 50 0.010
2 D MA H 51-720.0292 51-716.0292 51-750.0292 1 13 5 0.010
MH51-712.0292 51-708.0292 51-746.0292 1 13 51 0.010
-MAS51-282.0252 51-262.0252 51-272.0252 1 13 6 0.008
MS51-152.0252 51-122.0252 51-132.0252 1 13 52 0.008
3 NC + 3 NO - MA S 51-283.0252 51-263.0252 51-273.0252 1 13 3 0.010
MS51-153.0252 51-123.0252 51-133.0252 1 13 49 0.010
4 NC + 4 NO - MA S 51-284.0252 51-264.0252 51-274.0252 1 13 2 0.012
MS51-154.0252 51-124.0252 51-134.0252 1 13 48 0.012
51
Devices raised mounting
9
01.2010
Continuation see next page
Other lock numbers on request
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Keylock switch 2 positions
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Keylock switch 2 positions
Position A : Basic position
Position C : Maintained action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO MA UT A 51-445.036D 51-405.036D 51-415.036D 4 2 14760.017
C51-448.036D 51-408.036D 51-418.036D 4 2 14760.017
C + A 51-442.036D 51-402.036D 51-412.036D 4 2 14760.017
2 NO MA UT A 51-444.036D 51-404.036D 51-414.036D 4 2 14770.017
C51-447.036D 51-407.036D 51-417.036D 4 2 14770.017
C + A 51-441.036D 51-401.036D 51-411.036D 4 2 14770.017
SA 1 NC + 1 NO MA S A 51-255.025D2 51-295.025D2 51-235.025D2 2 14720.016
C51-355.025D2 51-395.025D2 51-335.025D2 2 14720.016
C + A 51-155.025D2 51-195.025D2 51-135.025D2 2 14720.016
S1 A 51-255.022D 51-295.022D 51-235.022D 2 14720.016
C51-355.022D 51-395.022D 51-335.022D 2 14720.016
C + A 51-155.022D 51-195.022D 51-135.022D 2 14720.016
2 NC + 2 NO MA S A 51-256.025D2 51-296.025D2 51-236.025D2 2 14730.016
C51-356.025D2 51-396.025D2 51-336.025D2 2 14730.016
C + A 51-156.025D2 51-196.025D2 51-136.025D2 2 14730.016
3 NC + 3 NO MA S A 51-257.025D2 51-297.025D2 51-237.025D2 2 14740.016
C51-357.025D2 51-397.025D2 51-337.025D2 2 14740.016
C + A 51-157.025D2 51-197.025D2 51-137.025D2 2 14740.016
4 NC + 4 NO MA S A 51-258.025D2 51-298.025D2 51-238.025D2 2 14750.016
C51-358.025D2 51-398.025D2 51-338.025D2 2 14750.016
C + A 51-158.025D2 51-198.025D2 51-138.025D2 2 14750.016
Position A : Basic position
Position C : Momentary action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO M UT A 51-458.036D 51-428.036D 51-438.036D 4 2 14700.017
2 NO M UT A 51-457.036D 51-427.036D 51-437.036D 4 2 14710.017
SA 1 NC + 1 NO M S A 51-145.025D2 51-495.025D2 51-141.025D2 2 14660.016
S1 A 51-145.022D 51-495.022D 51-141.022D 2 14660.016
2 NC + 2 NO M S A 51-146.025D2 51-496.025D2 51-142.025D2 2 14670.016
3 NC + 3 NO M S A 51-147.025D2 51-497.025D2 51-143.025D2 2 14680.016
4 NC + 4 NO M S A 51-148.025D2 51-498.025D2 51-144.025D2 2 14690.016
51
Devices raised mounting
10
01.2010
Continuation see next page
Other lock numbers on request
Switching system: SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Keylock switch 3 positions
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr.
Mounting dimensions
Technical drawing
Circuit drawing
e
Keylock switch 3 positions
Position C : Maintained action
Position A : Basic position
Position B : Maintained action
Standard lock 311
IP 65 SA 2 NC + 2 NO MA-0-MA S1 A 51-381.022D 51-361.022D 51-371.022D 21650.025
C + B 51-383.022D 51-363.022D 51-373.022D 21650.025
C+A+B 51-382.022D 51-362.022D 51-372.022D 21650.025
Position C : Maintained action
Position A : Basic position
Position B : Momentary action
Standard lock 311
IP 65 SA 2 NC + 2 NO MA-0-M S1 A 51-385.022D 51-365.022D 51-375.022D 21640.025
C + A 51-386.022D 51-366.022D 51-376.022D 21640.025
Position C : Momentary action
Position A : Basic position
Position B : Momentary action
Standard lock 311
IP 65 SA 2 NC + 2 NO M-0-M S1 A 51-384.022D 51-364.022D 51-374.022D 21630.025
Position C: Momentary action
Position A : Basic position
Position B : Maintained action
standard lock 311
IP 65 SA 2 NC + 2 NO M-0-MA S1 A 51-387.022D 51-367.022D 51-377.022D 21620.025
A + B 51-388.022D 51-368.022D 51-378.022D 21620.025
51
Devices raised mounting
11
01.2010
illuminative
Essential Accessories:
d Lever, raised mounting page 24
d Single-LED page 30
Continuation see next page
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Diode (1N 4007): - = without, D = Diode
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, H = Combined terminal: Solder-/ Universal (at contact/ at diode), S = Soldering terminal, S1 = Soldering
terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Selector switch 2 positions
0
Front protection
Switching system
Contacts
Diode (1N 4007)
Switching action
Terminals
Ø 18 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Selector switch 2 positions
Position A : Basic position
Position C : Maintained action
IP 65 LL 1 NC - MA UT 52-476.036 4 2 19 43 0.007
1 NC + 1 NO - MA UT 52-473.036 4 2 19 46 0.007
1 NO - MA UT 52-475.036 4 2 19 45 0.007
2 NC - MA UT 52-472.036 4 2 19 44 0.007
2 NO - MA UT 52-471.036 4 2 19 47 0.007
SA 1 NC + 1 NO 1 D MA H 52-747.0292 219400.008
2 D MA H 52-748.0292 219410.008
-MAS52-271.0252 219420.006
S1 52-271.022 219390.006
2 NC + 2 NO 1 D MA H 52-749.0292 219360.010
2 D MA H 52-750.0292 219370.010
-MAS52-272.0252 219380.006
3 NC + 3 NO - MA S 52-273.0252 219350.006
4 NC + 4 NO - MA S 52-274.0252 219340.006
Position A : Basic position
Position C : Momentary action IP 65 LL 1 NC - M UT 52-436.036 4 2 19 29 0.007
1 NC + 1 NO - M UT 52-433.036 4 2 19 32 0.007
1 NO - M UT 52-435.036 4 2 19 31 0.007
2 NC - M UT 52-432.036 4 2 19 30 0.007
2 NO - M UT 52-431.036 4 2 19 33 0.007
SA 1 NC + 1 NO 1 D M H 52-743.0292 219260.008
2 D M H 52-744.0292 219270.008
-MS52-131.0252 219280.006
S1 52-131.022 219250.006
2 NC + 2 NO 1 D M H 52-745.0292 219220.010
2 D M H 52-746.0292 219230.010
-MS52-132.0252 219240.006
3 NC + 3 NO - M S 52-133.0252 219210.006
4 NC + 4 NO - M S 52-134.0252 219200.006
51
Devices raised mounting
12
01.2010
illuminative
Essential Accessories:
d Lever, raised mounting page 24
d Single-LED page 30
Continuation see next page
Switching system: SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Selector swit ch 3 positio ns
0
Front protection
Switching system
Contacts
Switching action
Terminals
Ø 18 mm
Typ-Nr.
Mounting dimensions
Technical drawing
Circuit drawing
e
Selector switch 3 positions
Position C : Maintained action
Position A : Basic position
Position B : Maintained action
IP 40 SA 2 NC + 2 NO MA-0-MA S1 52-571.022A 2 6 19 0.015
M-0-MA S1 52-574.022A 2 6 17 0.015
Position C : Momentary action
Position A : Basic position
Position B : Momentary action
IP 40 SA 2 NC + 2 NO MA-0-M S1 52-573.022A 2 6 18 0.015
M-0-M S1 52-572.022A 2 6 16 0.015
51
Devices flush mounting
13
01.2010
Actuators usable for front dimensions: b 24 x 24 mm | a 24 x 30 mm | 25 mm dia.
Essential Accessories:
d Front bezel set for Indicators and Illuminated pushbutton, flush mounting page 25
d Lens plastic, flush mounting page 21
d Single-LED page 30
Continuation see next page
Terminals: S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm), UT = Universal terminal
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Indicator actuator, flush mounting
Front protection
Terminals
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Indicator actuator, flush mounting IP 65 S 51-050.005F 3 15 1 0.004
S1 51-050.002F 3 15 1 0.004
UT 51-051.006F 4 3 15 1 0.005
51
Devices flush mounting
14
01.2010
Actuators usable for front dimensions: b 24 x 24 mm | a 24 x 30 mm | 25 mm dia.
Essential Accessories:
d Front bezel set for Indicators and Illuminated pushbutton, flush mounting page 25
d Lens plastic, flush mounting page 21
d Single-LED page 30
Continuation see next page
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Illuminated pushbutton actuator, flush mounting
Front protection
Switching system
Contacts
Switching action
Terminals
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Illuminated pushbutton actuator, flush mounting IP 65 LL 1 NC MA UT 51-486.036F 4316110.006
MUT51-456.036F 4316570.006
1 NC + 1 NO MA UT 51-483.036F 4316140.006
MUT51-453.036F 4316600.006
1 NO MA UT 51-485.036F 4316130.006
MUT51-455.036F 4316590.006
2 NC MA UT 51-482.036F 4316120.006
MUT51-452.036F 4316580.006
2 NO MA UT 51-481.036F 4316150.006
MUT51-451.036F 4316610.006
SA 1 NC + 1 NO MA S 51-281.0252F 3 16 10 0.005
S1 51-281.022F 3 16 7 0.007
MS51-151.0252F 3 16 56 0.005
S1 51-151.022F 3 16 53 0.007
2 NC + 2 NO MA S 51-282.0252F 3 16 6 0.008
MS51-152.0252F 3 16 52 0.008
3 NC + 3 NO MA S 51-283.0252F 3 16 3 0.010
MS51-153.0252F 3 16 49 0.010
4 NC + 4 NO MA S 51-284.0252F 3 16 2 0.012
MS51-154.0252F 3 16 48 0.012
51
Devices flush mounting
15
01.2010
Continuation see next page
Essential Accessories:
d Front bezel set for Keylock switch, flush mounting page 26
Continuation see next page
Keylock switch actuator 2 positions, flush moun ting
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Keylock switch actuator
2 positions, flush mounting
Position A : Basic position
Position C : Maintained action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO MA UT A 51-445.036DF 4 3 17 76 0.027
C51-448.036DF 4 3 17 76 0.027
C + A 51-442.036DF 4 3 17 76 0.027
2 NO MA UT A 51-444.036DF 4 3 17 77 0.027
C51-447.036DF 4 3 17 77 0.027
C + A 51-441.036DF 4 3 17 77 0.027
SA 1 NC + 1 NO MA S A 51-255.025D2F 3 17720.027
C51-355.025D2F 3 17720.027
C + A 51-155.025D2F 3 17720.027
S1 A 51-255.022DF 3 17720.027
C51-355.022DF 3 17720.027
C + A 51-155.022DF 3 17720.027
2 NC + 2 NO MA S A 51-256.025D2F 3 17730.027
C51-356.025D2F 3 17730.027
C + A 51-156.025D2F 3 17730.027
3 NC + 3 NO MA S A 51-257.025D2F 3 17740.027
C51-357.025D2F 3 17740.027
C + A 51-157.025D2F 3 17740.027
4 NC + 4 NO MA S A 51-258.025D2F 3 17750.027
C51-358.025D2F 3 17750.027
C + A 51-158.025D2F 3 17750.027
Position A : Basic position
Position C : Momentary action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO M UT A 51-458.036DF 4 3 17 70 0.027
2 NO M UT A 51-457.036DF 4 3 17 71 0.027
SA 1 NC + 1 NO M S A 51-145.025D2F 3 17660.027
S1 A 51-145.022DF 3 17660.027
2 NC + 2 NO M S A 51-146.025D2F 3 17670.027
3 NC + 3 NO M S A 51-147.025D2F 3 17680.027
4 NC + 4 NO M S A 51-148.025D2F 3 17690.027
51
Devices flush mounting
16
01.2010
Continuation see next page
Position A : Basic position
Position C : Maintained action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO MA UT A 51-405.036DF 4 3 17 76 0.029
C51-408.036DF 4 3 17 76 0.029
C + A 51-402.036DF 4 3 17 76 0.029
2 NO MA UT A 51-404.036DF 4 3 17 77 0.029
C51-407.036DF 4 3 17 77 0.029
C + A 51-401.036DF 4 3 17 77 0.029
SA 1 NC + 1 NO MA S A 51-295.025D2F 3 17 72 0.029
C51-395.025D2F 3 17 72 0.029
C + A 51-195.025D2F 3 17 72 0.029
S1 A 51-295.022DF 3 17 72 0.029
C51-395.022DF 3 17 72 0.029
C + A 51-195.022DF 3 17 72 0.029
2 NC + 2 NO MA S A 51-296.025D2F 3 17 73 0.029
C51-396.025D2F 3 17 73 0.029
C + A 51-196.025D2F 3 17 73 0.029
3 NC + 3 NO MA S A 51-297.025D2F 3 17 74 0.029
C51-397.025D2F 3 17 74 0.029
C + A 51-197.025D2F 3 17 74 0.029
4 NC + 4 NO MA S A 51-298.025D2F 3 17 75 0.029
C51-398.025D2F 3 17 75 0.029
C + A 51-198.025D2F 3 17 75 0.029
Position A : Basic position
Position C : Momentary action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO M UT A 51-428.036DF 4 3 17 70 0.029
2 NO M UT A 51-427.036DF 4 3 17 71 0.029
SA 1 NC + 1 NO M S A 51-495.025D2F 3 17 66 0.029
S1 A 51-495.022DF 3 17 66 0.029
2 NC + 2 NO M S A 51-496.025D2F 3 17 67 0.029
3 NC + 3 NO M S A 51-497.025D2F 3 17 68 0.029
4 NC + 4 NO M S A 51-498.025D2F 3 17 69 0.029
Position A : Basic position
Position C : Maintained action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO MA UT A 51-415.036DF 4 3 17 76 0.026
C51-418.036DF 4 3 17 76 0.026
C + A 51-412.036DF 4 3 17 76 0.026
2 NO MA UT A 51-414.036DF 4 3 17 77 0.026
C51-417.036DF 4 3 17 77 0.026
C + A 51-411.036DF 4 3 17 77 0.026
SA 1 NC + 1 NO MA S A 51-235.025D2F 3 17 72 0.026
C51-335.025D2F 3 17 72 0.026
C + A 51-135.025D2F 3 17 72 0.026
S1 A 51-235.022DF 3 17 72 0.026
C51-335.022DF 3 17 72 0.026
C + A 51-135.022DF 3 17 72 0.026
2 NC + 2 NO MA S A 51-236.025D2F 3 17 73 0.026
C51-336.025D2F 3 17 73 0.026
C + A 51-136.025D2F 3 17 73 0.026
3 NC + 3 NO MA S A 51-237.025D2F 3 17 74 0.026
C51-337.025D2F 3 17 74 0.026
C + A 51-137.025D2F 3 17 74 0.026
4 NC + 4 NO MA S A 51-238.025D2F 3 17 75 0.026
C51-338.025D2F 3 17 75 0.026
C + A 51-138.025D2F 3 17 75 0.026
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
51
Devices flush mounting
17
01.2010
Continued from previous page
Other lock numbers on request
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Position A : Basic position
Position C : Momentary action
Standard lock 311
Front : Plastic black
IP 65 LL 1 NC + 1 NO M UT A 51-438.036DF 4 3 17 70 0.026
2 NO M UT A 51-437.036DF 4 3 17 71 0.026
SA 1 NC + 1 NO M S A 51-141.025D2F 3 17660.026
S1 A 51-141.022DF 3 17660.026
2 NC + 2 NO M S A 51-142.025D2F 3 17670.026
3 NC + 3 NO M S A 51-143.025D2F 3 17680.026
4 NC + 4 NO M S A 51-144.025D2F 3 17690.026
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
51
Devices flush mounting
18
01.2010
Essential Accessories:
d Front bezel set for Keylock switch, flush mounting page 26
Continuation see next page
Other lock numbers on request
Switching system: SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Keylock switch actuator 3 positions, flush mounting
0
Front protection
Switching system
Contacts
Switching action
Terminals
Key remove
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
Technical drawing
Circuit drawing
e
Keylock switch actuator
3 positions, flush mounting
Position C : Maintained action
Position A : Basic position
Position B : Maintained action
Standard lock 311
IP 65 SA 2 NC + 2 NO MA-0-MA S1 A 51-381.022DF 51-361.022DF 51-371.022DF 34650.027
C + B 51-383.022DF 51-363.022DF 51-373.022DF 34650.027
C+A+B 51-382.022DF 51-362.022DF 51-372.022DF 34650.027
Position C : Maintained action
Position A : Basic position
Position B : Momentary action
Standard lock 311
IP 65 SA 2 NC + 2 NO MA-0-M S1 A 51-385.022DF 51-365.022DF 51-375.022DF 34640.027
C + A 51-386.022DF 51-366.022DF 51-376.022DF 34640.027
Position C : Momentary action
Position A : Basic position
Position B : Maintained action
Standard lock 311
IP 65 SA 2 NC + 2 NO M-0-MA S1 A 51-387.022DF 51-367.022DF 51-377.022DF 34620.027
A + B 51-388.022DF 51-368.022DF 51-378.022DF 34620.027
Position C : Momentary action
Position A : Basic position
Position B : Momentary action
Standard lock 311
IP 65 SA 2 NC + 2 NO M-0-M S1 A 51-384.022DF 51-364.022DF 51-374.022DF 34630.027
51
Devices flush mounting
19
01.2010
illuminative
Actuators usable for front dimensions: b 24 x 24 mm | 25 mm dia.
Essential Accessories:
d Front bezel set for Selector switch, flush mounting page 26
d Lever, flush mounting page 24
d Single-LED page 30
Continuation see next page
Switching system: LL = Low level switching element, SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Selector switch actuator 2 positions, flush mounting
0
Front protection
Switching system
Contacts
Switching action
Terminals
Typ-Nr.
Component layout
Mounting dimensions
Technical drawing
Circuit drawing
e
Selector switch actuator 2 positions, flush mounting
Position A : Basic position
Position C : Maintained action
IP 65 LL 1 NC MA UT 52-476.036 4 3 18 43 0.007
1 NC + 1 NO MA UT 52-473.036 4 3 18 46 0.007
1 NO MA UT 52-475.036 4 3 18 45 0.007
2 NC MA UT 52-472.036 4 3 18 44 0.007
2 NO MA UT 52-471.036 4 3 18 47 0.007
SA 1 NC + 1 NO MA S 52-271.0252 318420.006
S1 52-271.022 318390.006
2 NC + 2 NO MA S 52-272.0252 318380.006
3 NC + 3 NO MA S 52-273.0252 318350.006
4 NC + 4 NO MA S 52-274.0252 318340.006
Position A : Basic position
Position C : Momentary action IP 65 LL 1 NC M UT 52-436.036 4 3 18 29 0.007
1 NC + 1 NO M UT 52-433.036 4 3 18 32 0.007
1 NO M UT 52-435.036 4 3 18 31 0.007
2 NC M UT 52-432.036 4 3 18 30 0.007
2 NO M UT 52-431.036 4 3 18 33 0.007
SA 1 NC + 1 NO M S 52-131.0252 318280.006
S1 52-131.022 318250.006
2 NC + 2 NO M S 52-132.0252 318240.006
3 NC + 3 NO M S 52-133.0252 318210.006
4 NC + 4 NO M S 52-134.0252 318200.006
51
Devices flush mounting
20
01.2010
illuminative
Actuators usable for front dimensions: b 24 x 24 mm | 25 mm dia.
Essential Accessories:
d Front bezel set for Selector switch, flush mounting page 26
d Lever, raised mounting page 24
d Single-LED page 30
Continuation see next page
Switching system: SA = Snap-action switching element
Contacts: NC = Normally closed, NO = Normally open
Switching action: MA = Maintained action, M = Momentary action
Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm)
Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47
Selector switch actuator 3 positions, flush mounting
0
Front protection
Switching system
Contacts
Switching action
Terminals
Typ-Nr.
Mounting dimensions
Technical drawing
Circuit drawing
e
Selector switch actuator 3 positions, flush mounting
Position C : Maintained action
Position A : Basic position
Position B : Maintained action
IP 40 SA 2 NC + 2 NO MA-0-MA S1 52-571.022A 3 5 19 0.015
M-0-MA S1 52-574.022A 3 5 17 0.015
Position C : Momentary action
Position A : Basic position
Position B : Momentary action
IP 40 SA 2 NC + 2 NO MA-0-M S1 52-573.022A 3 5 18 0.015
M-0-M S1 52-572.022A 3 5 16 0.015
21
01.2010
51
Accessories
Continuation see next page
mat
Continuation see next page
Front
Lens plastic, raised mounting
Lens
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr. e
Lens plastic, raised mounting
concave, illuminative blue transparent 51-954.6 51-904.6 0.001
colourless transparent 51-954.7 51-904.7 0.001
green transparent 51-954.5 51-904.5 0.001
orange transparent 51-954.3 51-904.3 0.001
red transparent 51-954.2 51-904.2 0.001
yellow transparent 51-954.4 51-904.4 0.001
flush, illuminative blue transparent 51-953.6 51-903.6 51-933.6 0.001
colourless transparent 51-953.7 51-903.7 51-933.7 0.001
green transparent 51-953.5 51-903.5 51-933.5 0.001
orange transparent 51-953.3 51-903.3 51-933.3 0.001
red transparent 51-953.2 51-903.2 51-933.2 0.001
smoked transparent 51-953.1 51-903.1 51-933.1 0.001
yellow transparent 51-953.4 51-903.4 51-933.4 0.001
flush, illuminative
(not recommended for film insert) blue translucent 51-951.6 51-901.6 51-931.6 0.001
colourless transparent 51-955.7 51-905.7 51-935.7 0.001
green translucent 51-951.5 51-901.5 51-931.5 0.001
green transparent 51-955.5 51-905.5 51-935.5 0.001
orange translucent 51-951.3 51-901.3 51-931.3 0.001
red translucent 51-951.2 51-901.2 51-931.2 0.001
red transparent 51-955.2 51-905.2 51-935.2 0.001
white translucent 51-951.9 51-901.9 51-931.9 0.001
yellow translucent 51-951.4 51-901.4 51-931.4 0.001
yellow transparent 51-955.4 51-905.4 51-935.4 0.001
flush, non-illuminative black opaque 51-951.0 51-901.0 51-931.0 0.001
grey opaque 51-951.8 51-901.8 51-931.8 0.001
concave, illuminative
(not recommended for film insert) colourless transparent 51-906.7 0.001
green transparent 51-906.5 0.001
red transparent 51-906.2 0.001
yellow transparent 51-906.4 0.001
Lens plastic, flush mounting
Lens
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr. e
Lens plastic, flush mounting
illuminative blue transparent flush 61-9671.6 61-9681.6 61-9642.6 0.002
colourless transparent flush 61-9671.7 61-9681.7 61-9642.7 0.002
green transparent flush 61-9671.5 61-9681.5 61-9642.5 0.002
orange transparent flush 61-9671.3 61-9681.3 61-9642.3 0.002
red transparent flush 61-9671.2 61-9681.2 61-9642.2 0.002
smoked transparent flush 61-9671.1 61-9681.1 61-9642.1 0.002
yellow transparent flush 61-9671.4 61-9681.4 61-9642.4 0.002
non-illuminative black opaque flush 61-9771.0 61-9781.0 0.002
grey opaque flush 61-9771.8 61-9781.8 0.002
white translucent flush 61-9771.9 61-9781.9 0.002
22
01.2010
51
Accessories
Continuation see next page
The silvery coat is being applied on the lens (screen print) with an additional protective lacquer.
can be hot stamped
Continuation see next page
mat
Continuation see next page
Lens plastic with symbol, flush mounting
Symbol Lens Ø 25 mm
Typ-Nr. e
Lens plastic with symbol, flush mounting
flush - level, illuminative ON/OFF blue transparent 61-9643.602 0.002
colourless transparent 61-9643.702 0.002
green transparent 61-9643.502 0.002
red transparent 61-9643.202 0.002
Ring blue transparent 61-9643.601 0.002
colourless transparent 61-9643.701 0.002
green transparent 61-9643.501 0.002
orange transparent 61-9643.301 0.002
red transparent 61-9643.201 0.002
yellow transparent 61-9643.401 0.002
Stand by blue transparent 61-9643.603 0.002
colourless transparent 61-9643.703 0.002
green transparent 61-9643.503 0.002
red transparent 61-9643.203 0.002
Marking plate for lens round plastic, flush mounting
Marking plate Typ-Nr. e
Marking plate for lens round plastic, flush mounting
only applicable with Lens round Typ-Nr. 61-9642.X Plastic colourless transparent 61-9707.7 0.001
Lens metal with spot, flush mounting
Lens Ø 25 mm
Typ-Nr. e
Lens metal with spot, flush mounting Aluminium black flush 61-9841.0A 0.002
Aluminium blue flush 61-9841.6A 0.002
Aluminium gold flush 61-9841.4A 0.002
Aluminium natural flush 61-9841.8A 0.002
Aluminium olive-green flush 61-9841.5A 0.002
Aluminium red flush 61-9841.2A 0.002
23
01.2010
51
Accessories
mat
Continuation see next page
Continuation see next page
Continuation see next page
Lens metal, flush mounting
Lens Ø 25 mm
Typ-Nr. e
Lens metal, flush mounting
convex Aluminium black 61-9842.0 0.003
Aluminium blue 61-9842.6 0.003
Aluminium gold 61-9842.4 0.003
Aluminium natural 61-9842.8 0.003
Aluminium olive-green 61-9842.5 0.003
Aluminium red 61-9842.2 0.003
flush Aluminium black 61-9841.0 0.002
Aluminium blue 61-9841.6 0.002
Aluminium gold 61-9841.4 0.002
Aluminium natural 61-9841.8 0.002
Aluminium olive-green 61-9841.5 0.002
Aluminium red 61-9841.2 0.002
Mushroom-head cap, flush mounting
Mushroom had cap Ø 32 mm
Typ-Nr. e
Mushroom-head cap, flush mounting Plastic black opaque 61-9593.0 0.004
Plastic green opaque 61-9593.5 0.004
Plastic red opaque 61-9593.2 0.004
Plastic yellow opaque 61-9593.4 0.004
Front bezel square for selector switch, raised mounting
Front bezel Typ-Nr. e
Front bezel square for selector switch, raised mounting
24 x 24 mm Plastic black 52-950.0 0.001
26 x 26 mm Plastic black 52-952.0 0.001
24
01.2010
51
Accessories
with bar and marking dot
Continuation see next page
with bar and marking dot
Continuation see next page
for devices 25 mm dia., flush mounting
Continuation see next page
Technical drawing from page 42
Lever, raised mounting
Lever Bar colour Typ-Nr. e
Lever, raised mounting
illuminative Plastic black blue 52-928.60 0.001
green 52-928.50 0.001
orange 52-928.30 0.001
red 52-928.20 0.001
yellow 52-928.40 0.001
Plastic grey blue 52-929.60 0.001
green 52-929.50 0.001
orange 52-929.30 0.001
red 52-929.20 0.001
yellow 52-929.40 0.001
non-illuminative Plastic black black 52-928.0 0.001
Plastic grey grey 52-929.8 0.001
white 52-929.9 0.001
Lever, flush mounting
Lever Bar colour Typ-Nr. e
Lever, flush mounting
illuminative Plastic black blue 61-9028.60 0.001
green 61-9028.50 0.001
orange 61-9028.30 0.001
red 61-9028.20 0.001
yellow 61-9028.40 0.001
Plastic grey blue 61-9029.60 0.001
green 61-9029.50 0.001
orange 61-9029.30 0.001
red 61-9029.20 0.001
yellow 61-9029.40 0.001
non-illuminative Plastic black black 61-9028.0 0.001
white 61-9028.9 0.001
Plastic grey grey 61-9029.8 0.001
white 61-9029.9 0.001
Legend frame
Typ-Nr.
Technical drawing
e
Legend frame
30 x 50 mm, adhesive, Aluminium black 61-9980.0 10 0.001
25
01.2010
51
Accessories
for Legend frame 61-9980.0
Continuation see next page
Continuation see next page
Mounting dimensions from page 41
Continuation see next page
Mounting dimensions from page 41
Legend plate insert
Typ-Nr. e
Legend plate insert
14.5 x 23.5 mm, adhesive, Aluminium black 704.968.1 0.001
14.5 x 23.5 mm, adhesive, Aluminium natural 704.968.0 0.001
Front bezel set for Indicators and Illuminated pushbutto n, flush mounting
Front bezel
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
e
Front bezel set for Indicators
and Illuminated pu shbutton,
flush mounting
Plastic black 61-9930.0 61-9931.0 61-9933.10 3 0.008
Plastic silver 61-9930.4 61-9931.4 3 0.008
Aluminium black 61-9933.1 3 0.006
Aluminium blue 61-9933.6 3 0.006
Aluminium gold 61-9933.4 3 0.006
Aluminium natural 61-9933.0 3 0.006
Aluminium olive-green 61-9933.5 3 0.006
Aluminium red 61-9933.2 3 0.006
Front bezel set for Mushroom-head pushbutton, flush mounting
Front bezel Ø 40 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
e
Front bezel set for Mushroom-head pushbutton,
flush mounting Aluminium natural 61-9934.8 4 0.013
Aluminium black 61-9933.1 4 0.006
Aluminium blue 61-9933.6 4 0.006
Aluminium gold 61-9933.4 4 0.006
Aluminium natural 61-9933.0 4 0.006
Aluminium olive-green 61-9933.5 4 0.006
Aluminium red 61-9933.2 4 0.006
Plastic black 61-9933.10 4 0.008
26
01.2010
51
Accessories
Continuation see next page
With the round front bezel sets Ø25 mm the anti-twist ring is part of the sales-package.
Mounting dimensions from page 41
Continuation see next page
With the round front bezel sets Ø25 mm the anti-twist ring is part of the sales-package.
Mounting dimensions from page 41
for flush - level lenses only for protection IP 68
Continuation see next page
ATTENTION
when using the front protection cover for push buttons the external sealing in the front bezel set and the silicone bellows
in the actuator are to be removed !
Front bezel set for Keylock switch, flush mounting
Front bezel
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
e
Front bezel set for Keylock
switch, flush mounting Plastic black 61-9930.0 61-9931.0 61-9932.10 3 0.008
Plastic silver 61-9930.4 61-9931.4 3 0.008
Aluminium black 61-9932.1 3 0.006
Aluminium blue 61-9932.6 3 0.006
Aluminium gold 61-9932.4 3 0.006
Aluminium natural 61-9932.0 3 0.006
Aluminium olive-green 61-9932.5 3 0.006
Aluminium red 61-9932.2 3 0.006
Front bezel set for Selector switch, flush mounting
Front bezel
b 24 x 24 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
e
Front bezel set for Selector switch, flush moun-
ting Plastic black 61-9936.0 3 0.007
Aluminium black 61-9932.1 3 0.006
Aluminium blue 61-9932.6 3 0.006
Aluminium gold 61-9932.4 3 0.006
Aluminium natural 61-9932.0 3 0.006
Aluminium olive-green 61-9932.5 3 0.006
Aluminium red 61-9932.2 3 0.006
Plastic black 61-9932.10 3 0.008
Front protective cap
Front protective cap Typ-Nr. e
Front protective cap
for front bezel set 24 x 30 mm, flush mounting Silicone natural transparent 61-9927.2 0.001
for front bezel set 25 mm dia., flush mounting Silicone natural transparent 84-9103.7 0.001
27
01.2010
51
Accessories
Continuation see next page
Technical drawing from page 42
Continuation see next page
Mounting dimensions from page 41, Technical drawing from page 42
Continuation see next page
Blind plugs fit also in mounting holes no. 2
Mounting dimensions from page 41
Continuation see next page
Mounting dimensions from page 41, Technical drawing from page 42
Protective cover, raised mounting
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr.
Technical drawing
e
Protective cover, raised moun ting
hinged, transparent, with means for sealing 51-920 2 0.002
51-925 3 0.002
Protective cover, flush mounting
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
Technical drawing
e
Protective cover, flush mounting
hinged, transparent, with means for sealing 61-9921.0 3 7 0.006
61-9922.0 3 8 0.006
slide by side, with means not for sealing 61-9924.0 3 9 0.006
Blind plug, raised mounting
Blind plug
b 18 x 18 mm
Typ-Nr.
a 18 x 24 mm
Typ-Nr. Ø 18 mm
Typ-Nr.
Mounting dimensions
e
Blind plug, raised mounting Plastic black 51-948.0 51-947.0 51-949.0 1 0.003
Blind plug, flush mounting
Blind plug
b 24 x 24 mm
Typ-Nr.
a 24 x 30 mm
Typ-Nr. Ø 25 mm
Typ-Nr.
Mounting dimensions
Technical drawing
e
Blind plug, flush mounting Plastic black 61-9451.0 61-9452.0 3 0.006
61-9453.0 3 11 0.006
28
01.2010
51
Accessories
Continuation see next page
Continuation see next page
Other lock numbers on request
Continuation see next page
>
Continuation see next page
PCB plug-in base Pins right-angle : With the extendable mounting the distance between plug-in base and PCB can be
varied up to 3 mm.
Terminals: P = PCB terminal
Component layout from page 40
Continuation see next page
Master key
Typ-Nr. e
Master key
Lock numbers 311 ... 445 (DOM) 31-989.300 0.006
Spare key
Typ-Nr. e
Spare key
Key lock switch, standard lock 311 (DOM) 31-989.311 0.006
EMC Key protection cap
Typ-Nr. e
EMC Key protection cap
Plastic black, for lock type DOM 31-985.0 0.005
Backside
PCB plug-in base
Terminals
Typ-Nr.
Component layout
e
PCB plug-in base
16.4 mm dia. x 9.8 mm for Low level switching element, Pins axial P31-940 2 0.002
17.8 x 12.9 mm x 9.8 mm for Snap-action switching element 2.8 mm, Pins axial P 31-942 3 0.002
17.9 x 17.9 x 8.4 mm for Low level switching element, Pins bent at right-angle P 31-941 1 0.004
Multi-plug housing
Typ-Nr. e
Multi-plug housing
for Switching block 51-943.0 0.005
29
01.2010
51
Accessories
Continuation see next page
Continuation see next page
Continuation see next page
>
Continuation see next page
Flat receptacle
Typ-Nr. e
Flat receptacle
2.0 x 0.5 mm for Universal terminal 31-945 0.001
2.8 x 0.5 mm for Multi-plug housing 51-943.1 0.001
2.8 x 0.5 mm for Plug-in terminal 31-946 0.001
Insulation sleeve
Typ-Nr. e
Insulation sleeve
Cover Plug-in terminals for snap-action switching element 2.8 mm 01-928 0.001
for Flat receptacle 31-945 31-928 0.001
for Flat receptacle 31-946 31-929 0.001
Terminal cover
Typ-Nr. e
Terminal cover 01-929 0.010
Illumination
Filament lamp
Socket Operating voltage/-current Typ-Nr. e
Filament lamp T1 3/4 MG 12 VAC/DC, 75 mA 10-1309.1309 0.001
14 VAC/DC, 80 mA 10-1310.1319 0.001
18 VAC/DC, 40 mA 10-1311.1249 0.001
24 VAC/DC, 35 mA 10-1312.1229 0.001
28 VAC/DC, 30 mA 10-1313.1209 0.001
28 VAC/DC, 40 mA 10-1313.1249 0.001
36 VAC/DC, 20 mA 10-1316.1179 0.001
36 VAC/DC, 30 mA 10-1316.1209 0.001
48 VAC/DC, 20 mA 10-1319.1179 0.001
48 VAC/DC, 25 mA 10-1319.1199 0.001
6 VAC/DC, 120 mA 10-1306.1349 0.001
6.3 VAC/DC, 200 mA 10-1307.1369 0.001
30
01.2010
51
Accessories
Continuation see next page
Note:
AC operation through halve-wave rectifier possible, slight flicker ing can occure.
for lamp voltage reduction
Continuation see next page
Please keep to the country specific security rules.
for fitting with series resistors
Continuation see next page
Single-LED
Socket Light colour Operating voltage/-current Typ-Nr. e
Single-LED T1 3/4 MG blue 12 VAC/DC, 7 /14 mA 10-2J09.1066 0.002
24 VAC/DC, 7/14 mA 10-2J12.1066 0.002
28 VAC/DC, 7/14 mA 10-2J13.1066 0.002
48 VAC/DC, 4/8 mA 10-2J19.1046 0.002
6 VDC, 15 mA 10-2J06.3146 0.002
green 12 VAC/DC, 4/7 mA 10-2J09.1065 0.002
24 VAC/DC, 4/7 mA 10-2J12.1065 0.002
28 VAC/DC, 4/7 mA 10-2J13.1065 0.002
48 VAC/DC, 2/4 mA 10-2J19.1045 0.002
6 VDC, 7 mA 10-2J06.3145 0.002
red 12 VAC/DC, 7/14 mA 10-2J09.1062 0.002
24 VAC/DC, 7/14 mA 10-2J12.1062 0.002
28 VAC/DC, 7/14 mA 10-2J13.1062 0.002
48 VAC/DC, 4/8 mA 10-2J19.1042 0.002
6 VDC, 15 mA 10-2J06.3142 0.002
white diffuse 12 VAC/DC, 7/14 mA 10-2J09.1069 0.002
24 VAC/DC, 7/14 mA 10-2J12.1069 0.002
28 VAC/DC, 7/14 mA 10-2J13.1069 0.002
48 VAC/DC, 4/8 mA 10-2J19.1049 0.002
6 VDC, 15 mA 10-2J06.3149 0.002
yellow 12 VAC/DC, 7/14 mA 10-2J09.1064 0.002
24 VAC/DC, 7/14 mA 10-2J12.1064 0.002
28 VAC/DC, 7/14 mA 10-2J13.1064 0.002
48 VAC/DC, 4/8 mA 10-2J19.1044 0.002
6 VDC, 15 mA 10-2J06.3144 0.002
Series resistor
Operating voltage Typ-Nr. e
Series resistor
10 kΩ, for filament lamp 48 VAC, 25 mA 230/240 V 02-904.7 0.003
2.7 kΩ, for filament lamp 48 VAC, 25 mA 110 V 02-904.0 0.003
3.3 kΩ, for filament lamp 48 VAC, 25 mA 125 V 02-904.1 0.003
4.7 kΩ, for filament lamp 48 VAC, 25 mA 145 V 02-904.3 0.003
Terminal plate emp t y
Typ-Nr. e
Terminal plate empty
10 spaces 125 x 60 x 15 mm 02-912.2 0.045
15 spaces 187.5 x 60 x 15 mm 02-912.3 0.090
20 spaces 250 x 60 x 15 mm 02-912.4 0.095
5 spaces 62.5 x 60 x 15 mm 02-912.1 0.025
31
01.2010
51
Accessories
>
Continuation see next page
for Key lock- and Selector switch
Continuation see next page
Continuation see next page
Continuation see next page
CAUTION
A switching process might be released when replacing the lamp/LED !
Continuation see next page
Continuation see next page
Assembling
Fixing nut
Typ-Nr. e
Fixing nut
Metal, specifically for keylock switches 31-991 0.005
Anti-twist ring
Typ-Nr. e
Anti-twist ring 51-910 0.001
Lens remover
Typ-Nr. e
Lens remover
for flush mounting 61-9730.0 0.011
for raised mounting 02-905 0.011
Lamp remover
Typ-Nr. e
Lamp remover 61-9740.0 0.003
Mounting tool
Typ-Nr. e
Mounting tool 01-907 0.020
Dismantling tool
Typ-Nr. e
Dismantling tool
for dismantling of Lens, Lens holder and Switching element block 51-938 0.027
32
01.2010
51
Accessories
Continuation see next page
Flat receptacle remover
Typ-Nr. e
Flat receptacle remover
for removing the Flat receptacle of the Multi-plug in housing 51-943.9 0.001
33
01.2010
51
Technical Data
Switching system
Self-cleaning, double-break, snap action switching system (with
contact gap 2 x 0.5 mm).
1 normally closed or 1 normally open contact per element.
Snap-action switching elements with soldering terminals at the
sides: up to 4 switching element can be on a pushbutton (max. 4
normally closed and 4 normally open contacts).
Snap-action switching element with axial plug-in terminals 2.8 mm
stachable, only 1 switching element can be on a pushbutton.
Material
Material of contact
Gold plated silver
Switch housing
Axial soldering-/plug-in terminal 2.8 mm:
Diallylphthalate DAP, Polyamide 66, Polysulfone, heat-resistant
and self-extinguishing.
Soldering terminal: PA 6.6 Ultramid
Actuator housing
Polyetherimide, self-extinguishing
Mechanical characteristics
Terminals
Snap-action switching element with tinned soldering terminals at
the sides:
Max. wire diameter 2 wires à 1.2 mm
Max. wire cross-section of stranded cable 1 x 1 mm²
Snap-action switching element with axial soldering terminals, which
can also be used as plug-in terminals 2.8 x 0.5 mm:
Max. wire diameter 2 wires of 1 mm
Max. wire cross-section of stranded cable 2 of 0.75 mm² or 1 x 1.0
mm²
Actuating torque
2.5 Ncm ... 5.5 Ncm, depending on the number of switching
elements. Measured at the key or lever of the keylock- or selector
switch.
Actuating force
4 N ... 6 N, depending on the number of switching elements
Actuating travel
Illuminated pushbutton 3 mm
Keylock-/selector switch actuator 2 positions:
1x ca. 42° deflection momentary action
1x ca. 90° deflection maintained action
Rebound time
≤5ms
Mechanical lifetime
0
Electrical cha rac te ris tic s
Standards
IEC 61058, EN 61058
Rated voltage
250 VAC/VDC
Rated current
5 A
Contact resistance
Starting value (initial) ≤50 mΩ
Electrostatic discharge (ESD)
≤15 KV (Keylock switch)
Conventional free air thermal current
5 A
The maximum current in continuous operation and at ambient
temperature not exceeding the quoted maximum values.
Switch rating
250 VAC, 5 A (cosφ 1)
250 VAC, 3 A (cosφ 0,3)
Switch rating AC (cosφ 0,7)
0
Switch rating DC (inductive) L:R = 30 ms
0
Electric strength
2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per
IEC 60512-2-11
Protection class
II
Environmental conditions
Storage temperature
-40 °C ... +85 °C
Service temperature
-25 °C ... +55 °C
For indicators and illuminated pushbuttons mounted as a block,
make sure the heat can escape freely.
Protection degree
IP 65 front side, as per IEC 60529
Shock resistance
(Single impacts, semi-sinusoidal)
15 g for 11 ms, as per IEC 60512-4-3, IEC 60068-2-27
Vibration resistance
(Sinusoidal)
10 g at 10 Hz ... 1500 Hz, amplitude 1.5 mm, as per IEC 60512-4 -
4, IEC 60068-2-6
Climate resistance
Standard condition, as per IEC 60068-2-3 and 2-30
Changing condition, as per IEC 60068-2-14 and 2-33
Approvals
Approbations
CB (IEC 61058)
CSA
ENEC (EN 61058)
Germanischer Lloyd
UL
Actuator with snap-action switching element
Momentary action 2 million cycles of operation
Maintained action 1 million cycles of operation
Keylock switch 50 000 cycles of operation
Voltage 125 VAC 250 VAC
Current 3 A 2 A
Voltage 24 VDC 60 VDC 110 VDC 220 VDC
Current 2 A 0.7 A 0.2 A 0.1 A
34
01.2010
51
Technical Data
Declaration of conformity
CE
>
Switching system
Self-cleaning, double-break, snap action switching system
1 normally closed or 1 normally open contact per element.
Material
Material of contact
Gold plated hardsilver
Switch housing
Diallylphthalate (DAP), heat-resistant and self-extinguishing
Actuator housing
Polyetherimide, self-extinguishing
Mechanical characteristics
Terminals
Soldering terminal which can also be used as plug-in terminal
2.8 x 0.5 mm:
Max. wire diameter 2 wires of 1 mm
Max. wire cross-section of stranded cable 2 x 0.75 mm²
Actuating torque
2.5 Ncm ... 5.5 Ncm, depending on the number of switching
elements. Measured at the key or lever of the keylock- or selector
switch.
Actuating travel
Keylock-/selector switch actuator with 3 positions
2x ca. 42° deflection momentary action
2x ca. 90° deflection maintained action
Rebound time
≤5ms
Mechanical lifetime
0
Electrical characteristics
Electrostatic discharge (ESD)
≤15 KV (Keylock switch)
Conventional free air thermal current
5 A
The maximum current in continuous operation and at ambient
temperature not exceeding the quoted maximum values.
Switch rating
250 VAC, 5 A (cosφ 0,75)
Electric strength
2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per
IEC 60512-2-11
Protection class
II
Environmental conditions
Storage temperature
-40 °C ... +85 °C
Service temperature
-25 °C ... +55 °C
for selector switches mounted as a block, make sure the hea t can
escape freely
Protection degree
Front side, as per IEC 60529
IP 65 keylock switch
IP 40 selector switch
Approvals
Approbations
CB (IEC 61058)
CSA
ENEC (EN 61058)
Germanischer Lloyd
UL
Declaration of conformity
CE
>
Switching system
This low level switching element was designed for switching low
powers in electronic circuits. The mechanism assures reliable swit-
ching of loads ranging from a few μA / μV up to 100 mA / 42 VAC/
DC.
Single-break momentary contact, as normally open or normally
closed with 4 independent points of contact. 2 momentary contacts
per switching element; combination of normally open and normally
closed is possible.
Special features are the long life, extremely short rebound time and
stable contact resistance.
Material
Material of contact
Gold plated
Switch housing
Polysulfone, heat-resistant and self-extinguishing
Actuator housing
Polyetherimide, self-extinguishing
Mechanical characteristics
Terminals
The universal terminals permit these units to be mounted on printed
circuit boards (PCB). These terminals can also be used as
soldering or plug-in terminals.
For these terminals we can also supply a plug-in base which, when
soldered on to the board, enables the switch to be plugged in.
Soldering terminal:
Max. wire diameter 2 wires à 0.8 mm
Max. wire cross-section of stranded cable 1x 0.75 mm²
Plug-in terminal 2.0 x 0.5 mm
Actuating torque
2.5 Ncm ... 5.5 Ncm, measured at the key or lever of the keylock- or
selector switch
Actuator with snap-action switching element block
(Keylock- and Selector switch 3 positions)
Keylock switch 50 000 cycles of operation
Selector switch 100 000 cycles of operation
Actuator with low level switching element
35
01.2010
51
Technical Data
Actuating force
3 N ... 3,5 N
Actuating travel
Illuminated pushbutton 3 mm
Keylock-/selector switch actuator 2 positions:
1x ca. 42° deflection momentary action
1x ca. 90° deflection maintained action
Rebound time
Typ. <100 μs
Mechanical lifetime
0
Electrical cha rac te ris tic s
Contact resistance
Starting value (initial) ≤50 mΩ
Electrostatic breakdown value
≤15 KV (Keylock switch)
Switch rating
10 μA, 100 μV to 100 mA at 42 VAC/VDC
Electric strength
2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per
IEC 60512-2-11
Environmental conditions
Storage temperature
-40 °C ... +85 °C
Service temperature
-25 °C ... +55 °C
For indicators and illuminated pushbuttons mounted as a block,
make sure the heat can escape freely.
Protection degree
IP 65 front side, as per IEC 60529
Shock resistance
(Single impacts, semi-sinusoidal)
15 g for 11 ms, as per IEC 60512-4-3, IEC 60068-2-27
Momentary action 5 million cycles of operation
Maintained action 1 million cycles of operation
Keylock switch 50 000 cycles of operation
51
Typical Applications
36
01.2010
When indicators and illuminated pushbuttons equipped with diodes, the user is able to perform a lamp check or wire an alarm
circuit simply with a considerable saving of space.
0
Diode element
51
Application guidelines
37
01.2010
When switching inductive loads such as relays, DC motors, and DC soleno ids, it is always important
to absorb surges (e.g. with a diode) to protect the contacts. When these inductive loads are switched
off, a counter emf can severely damage switch contacts and greatly shorten lifetime.
Fig. 1 shows an inductive load with a free-wheeling diode connected in parallel. This free-wheeling
diode provides a path for the inductor current to flow when the current is interrupted by the switch.
Without this free-wheeling diode, the voltage across the coil will be limited only by dielectric break-
down voltages of the circuit or parasitic elements of the coil. This voltage can be kilovolts in amplitude
even when nominal circuit voltages are low (e.g. 12 VDC) see Fig. 2.
The free-wheeling diode should be chosen so that the reverse breakdown voltage is greater than the
voltage driving the inductive load. The DC blocking voltage (VR) of the free-wheeling diode can be
found in the datasheet of a diode. The forward current should be equal or greater than the maximum
current flowing through the load.
To get an efficient protection, the free-wheeling diode must be connected as close as possible
to the inductive load!
0
Suppressor circuits
Sveral hundred
to several
thousend volts
ON OFF
0
e = L di
dt
__
VDC
Switch
Free-wheeling
diode
Inductive
load
Counter emf
over load without free-wheeling diode
Fig. 2
Switching with inductive load
Fig. 1
+
_
51
Marking
38
01.2010
0
>
All dimensions in mm
0
0
>
General notes
1. Engraving
In addition to the most commonly used world
languages, in DIN 1451-3 close spacing, other
typefaces are available as Scandinavian,
Slavic, Greek, Russian and Polish.
Red, blue and black lenses are filled with white
colour. Other colour lenses are filled in black.
Standard height of letters is 2 mm. If the height
is not specified, we will supply 2 mm engraved
letters.
2. Hot stamping
For larger series it is worth considering
markings by means of hot stamping We will
pleased to advise you.
For letters and figures, typefaces with 2.5 mm,
3 mm and 4 mm are available.
3. Film inserts
Instead of using engraving the lenses can be
fitted with transparent film inserts, as an
alternative. For this purpose, though, it is
advisible to use transparent lenses.
In the case of use of a smoke-black lens the
fitted film becomes readable only if the lamp is
on.
The film thickness is 0.2 mm.
Important : Consider pushbutton mounting
orientation befor specifying engraving
characters !
Lenses for indicators and illuminated pushbuttons, raised mounting
Front size
(Lens) Film insert
max. size Height of letters
hNumber of lines Number of (target value)
capital letters per line Number of (target value)
small letters per line Image
18 dia.
(15.8 dia.) 12.8 dia. 2 3 6 6 B4
325 6 B4
423 4 B4
512 3 B4
612 3 B4
812 2 B4
18 x 18
(15.3 x 15.3) 12.7 x 12.7 2 4 7 - 8 8 B3
336 - 7 7 B3
424 - 5 5 B3
523 - 4 4 B3
613 3 - 4 B3
812 - 3 2 - 3 B3
18 x 24
(15.3 x 21.5) 12.7 x 18.7 2 4 11 12 B1
57 - 8 8 B2
3 3 9 -10 10 - 11 B1
46 - 7 7 B2
427 7 - 8 B1
34 - 5 5 B2
525 - 6 6 B1
3 - 4 4 B2
614 - 5 5 B1
23 3 - 4 B2
813 - 4 3 - 4 B1
2 - 3 2 - 3 B2
B1 B2 B4B3
h
Engraving
Film
AB
abc abc
AB
abc
AB
abc
AB
51
Marking
39
01.2010
All dimensions in mm
0
0
Lenses for indicators and illuminated pushbuttons, flu sh mounting
Front size
(Lens) Film insert
max. size Height of letters
hNumber of lines Number of (target value)
capital letters per line Number of (target value)
small letters per line Image
24 x 24
(18 x 18) 15.1 x 15.1 2 4 8 - 9 9 B3
337 - 8 8 B3
424 - 5 5 B3
524 4 - 5 B3
614 4 B3
8 1 2 - 3 2 - 3 B3
24 x 30
(18 x 24) 15.1 x 21 2 4 12 13 B1
58 - 9 9 B2
3 3 10 - 11 11 - 12 B1
47 - 8 8 B2
427 8 B1
34 - 5 5 B2
525 - 6 6 B1
44 - 5B2
614 - 5 5 B1
23 3 - 4 B2
8 1 3 - 4 3 - 4 B1
2 - 3 2 - 3 B2
25 dia.
(19.7 dia.) Marking plate 2 3 6 6 B4
325 6 B4
423 4 B4
512 3 B4
612 3 B4
812 2 B4
B1 B2 B4B3
h
Engraving
Film
AB
abc abc
AB
abc
AB
abc
AB
51
Drawings
40
01.2010
1 PCB plug-in base page 28
2 PCB plug-in base page 28
3 PCB plug-in base page 28
4 Indicator actuator page 7 | Illuminated pushbutton actuator page 8 | Keylock switch 2 positions page 9 | Selector switch 2 positions
page 11 | Indicator actuator, flush mounting page 13 | Illuminated pushbutton actuator, flush mounting page 14 | Keylock switch actuator
2 positions, flush mounting page 15 | Selector switch actuator 2 positions, flush mounting page 19
Component layout
3
42
1
b
b3421a
a
all holes
Switch
Extendable
mounting pins
Drilling plan (conductor side)
15.24
17.9
9.6
17.9
7.62
1.271.27
0.85
5 x 2.54
1.27 1.27
Ø1.0
9
34
Ø2.1 hole for
central mounting
with M2 screw,
if desired
all holes
Ø1.0
5.08
10.16
12.7
3.813.81
Ø2.1 hole for
central mounting
with M2 screw,
if desired all holes
Ø1.0
+
0.1
0
3.813.81
7.62
10.16
7.62
PCB layout (conductor side)Terminal (rearside)
1
24
3
ab
1
24
3
ab
1
24
3
ab
Anti twist device
10.16
5.08 2.54
7.62
3.81
Round Square Rectangular
Ø1.0
all holes
51
Drawings
41
01.2010
1 Indicator actuator page 7 | Illuminated pushbutton actuator page 8 | Blind plug, raised mounting page 27
2 Keylock switch 2 positions page 9 | Keylock switch 3 positions page 10 | Selector switch 2 positions page 11 | Selector switch
3 positions page 12
3 Indicator actuato r, flush mounting page 13 | Illuminated pushbutton actuator, flush mounting page 14 | Keylock switch actuator
2 positions, flush mounting page 15 | Keylock switch actuator 3 positions, flush mounting page 18 | Selector switch actuator 2 positions,
flush mounting page 19 | Selector switch actuator 3 positions, flush mounting page 20 | Front be zel set for Indicators and Illuminated
pushbutton, flush mounting page 25 | Front bezel set for Keylock switch, flush mounting page 26 | Front bezel set for Selector switch,
flush mounting page 26 | Protective cover, flush mounting page 27 | Blind plug, flush mounting page 27
- Hole spacing min. 26 mm / min. 26 mm by using of the round front protective cap 84-9103.7
- Hole spacing min. 31 mm / min. 25 mm by using of the rectangular fr ont protectice cap 61-9927.2
Mounting dimensions
18 x 18 mm Ø18 mm
18 x 24 mm
18 min.
18 min.
18 min.
24 min.
16
+
0.2
0
18 min.
18 min.
18 x 18 mm Ø18 mm
18 x 24 mm
15
+
0.05
0
18 min.
18 min.
18 min.
24 min.
16
+
0.2
0
1.7
0
-
0.1
18 min.
18 min.
25 min.
30 min.
24 min.
25 min.
Ø25 mm
22.3 +
0.4
0
27 +
0.25
-
0.15
21 +
0.25
-
0.15
24 min.
24 min.
24 x 30 mm 24 x 24 mm
21 +
0.25
-
0.15
21 +
0.25
-
0.15
51
Drawings
42
01.2010
4 Front bezel set for Mushroom-head pushbutton, flus h mounting page 25
1 Keylock switch 3 positions page 10
2 Protective cover, raised mounting page 27
3 Protective cover, raised mounting page 27
Technica l dra wi n g
Ø40 = 40 min.
Ø32 = 35 min.
Ø32 mm
Ø40 mm
22.3
+
0.4
0
Ø40 = 40 min.
Ø32 = 32 min.
18 x 24 mm 18 x 18 mm Ø 18 mm
42
11.5
35
1.5 ... 6
2.8 x 0.5
10.5
25.5
20
23.5
14.5
32
14.5
32
24
23.5
25.5
10.5
51
Drawings
43
01.2010
4 Keylock switch actuator 3 positions, flush mounting page 18
5 Selector switch actuator 3 positions, flush mounting page 20
6 Selector switch 3 positions page 12
24 x 30 mm 24 x 24 mm Ø 25 mm
2.8 x 0.5
50
3.5
27
1.5 ... 5
24 x 24 mm Ø 25 mm
50
9.5
1.5 ... 5
2.8 x 0.5
2
Ø 18 mm
42
6
14
1.5 ... 6
2.8 x 0.5
51
Drawings
44
01.2010
7 Protective cover, flush mounting page 27
8 Protective cover, flush mounting page 27
9 Protective cover, flush mounting page 27
10 Legend frame page 24
11 Blind plug, flush mounting page 27
245.5 max.
24
25
12
4.5
245.5 max.
30
25
12
4.5
Ø25
42
29.3 1.5 min.
5.5 max.
10
14.5
50
30
23.5
4
Ø25
25
1...5
23.5
2
16.5 min.
20.5 max.
51
Drawings
45
01.2010
12 Indicator actuator page 7
13 Illuminated pushbutton actuator page 8
14 Keylock switch 2 positions page 9
18 x 24 mm 18 x 18 mm Ø 18 mm
Soldering terminal
Universal terminal
Soldering terminal
(also plugable)
Universal terminal
+ diodes
LL1UU+D
23 26 35 -
351D, 2D
L1
L
U+D
U
10.5
3
2.8 x 0.5
1.5 ... 6
18 x 24 mm 18 x 18 mm Ø 18 mm
Soldering terminal
Universal terminal
Combined terminal
+ diodes
Soldering terminal
(also pluggable)
LH+DL1 U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
1NC+1NO+D
2NO+2NC+D
28
35.5
43
50.5
36
-
-
-
43.5
51
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO -
35
1.5 ... 6
L
10.5
L1 H+D
U
3
2.8 x 0.5
Soldering terminal
Universal terminal
Soldering terminal
(also pluggable)
LL1U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
26.5
34
41.5
49
36
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO 35.5
18 x 24 mm
L1
L
11.5
35
1.5 ... 6 18 x 18 mm
2.8 x 0.5
Ø 18 mm
U
3
51
Drawings
46
01.2010
15 Indicator actuator, flush mounting page 13
16 Illuminated pushbutton actuator, flush mounting page 14
17 Keylock switch actuator 2 positions, flush mounting page 15
24 x 30 mm 24 x 24 mm Ø 25 mm
Soldering terminal
Universal terminal
Soldering terminal
(also pluggable)
LL1U
31 34 44
L1
L
2
U
3
2.8 x 0.5
1.5 ... 4
24 x 30 mm 24 x 24 mm Ø 25 mm
L1
L
U
2
3
2.8 x 0.5
1.5 ... 4
Soldering terminal
Universal termnal
Soldering terminal
(also pluggable)
LL1U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
36.5
44
51.5
59
44
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO 44
Soldering terminal
Universal terminal
Soldering terminal
(also pluggable)
LL1U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
35
42.5
50
57.5
44.5
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO 44.5
24 x 30 mm 24 x 24 mm Ø 25 mm
L1
L
3.5
27
1.5 ... 5
2.8 x 0.5
U
3
51
Drawings
47
01.2010
18 Selector switch actuator 2 positions, flush mounting page 19
19 Selector switch 2 positions page 11
1 Indicator actuator page 7 | Indicator actuator, flush mounting page 13
2 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
3 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
Circuit drawing
Soldering terminal
Universal terminal
Soldering terminal
(also pluggable)
LL1U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
41
48.5
56
63.5
48
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO 48
24 x 24 mm Ø 25 mm
L1
L
9.5
2
1.5 ... 6
2.8 x 0.5
U
3
18 x 24 mm 18 x 18 mm Ø 18 mm
Soldering terminal
Universal terminal
Combined terminal
+ diodes
Soldering terminal
(also pluggable)
LH+DL1 U
1NC+1NO
2NC+2NO
3NC+3NO
4NC+4NO
1NC+1NO+D
2NC+2NO+D
32
39.5
47
54.5
36
-
-
-
43.5
51
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1NC, 1NO, 1NC+1NO, 2NC, 2NO -
39
1.5 ... 6
L
6
14
L1 H+D
U
3
2.8 x 0.5
b+(x2)
a-(x1)
31x1-
24x2+
I
31
24
II
31
24
III
31
24
IV
31x1-
24x2+
I
31
24
II
31
24
III
51
Drawings
48
01.2010
4 Illuminated pushb utton actuator page 8
5 Illuminated pushb utton actuator page 8
6 Illuminated pushb utton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
7 Illuminated pushb utton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
8 Illuminated pushb utton actuator page 8
9 Illuminated pushb utton actuator page 8
10 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
11 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
31a-
24b+
3(+)
4(-)
I
31
24
II
31a-
24b+
3(+)
4(-)
I
31
24
II
1(-)
2(+)
31x1-
24x2+
I
31
24
II
31a-
24b+
I
31a-
24b+
3(+)
4(-)
I
31a-
24b+
3(+)
4(-)
I
1(-)
2(+)
31x1-
24x2+
I
1a-
2b+
51
Drawings
49
01.2010
12 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
13 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
14 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
15 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
16 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20
17 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20
18 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20
19 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20
1a-
2
3
4b+
1a-
2b+
13a-
4
2b+
13a-
4
2b+
31
24
C
31
24
B
a-
b+
31
24
C
31
24
B
a-
b+
31
24
C
31
24
B
a-
b+
31
24
C
31
24
B
a-
b+
51
Drawings
50
01.2010
20 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
21 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
22 Selector switch 2 positions page 11
23 Selector switch 2 positions page 11
24 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
25 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
26 Selector switch 2 positions page 11
27 Selector switch 2 positions page 11
31x1-
24x2+
I
31
24
II
31
24
III
31
24
IV
31x1-
24x2+
I
31
24
II
31
24
III
31a-
24b+
3(+)
4(-)
I
31
24
II
31a-
24b+
3(+)
4(-)
I
31
24
II
1(-)
2(+)
31x1-
24x2+
I
31
24
II
31a-
24b+
I
31a-
24b+
3(+)
4(-)
I
31a-
24b+
3(+)
4(-)
I
1(-)
2(+)
51
Drawings
51
01.2010
28 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
29 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
30 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
31 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
32 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
33 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
34 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
35 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
31x1-
24x2+
I
1a-
2b+
1a-
2
3
4b+
1a-
2b+
13a-
4
2b+
13a-
4
2b+
31x1-
24x2+
I
31
24
II
31
24
III
31
24
IV
31x1-
24x2+
I
31
24
II
31
24
III
51
Drawings
52
01.2010
36 Selector switch 2 positions page 11
37 Selector switch 2 positions page 11
38 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
39 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
40 Selector switch 2 positions page 11
41 Selector switch 2 positions page 11
42 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
43 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
31a-
24b+
3(+)
4(-)
I
31
24
II
31a-
24b+
3(+)
4(-)
I
31
24
II
1(-)
2(+)
31x1-
24x2+
I
31
24
II
31a-
24b+
I
31a-
24b+
3(+)
4(-)
I
31a-
24b+
3(+)
4(-)
I
1(-)
2(+)
31x1-
24x2+
I
1a-
2b+
51
Drawings
53
01.2010
44 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
45 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
46 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
47 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19
48 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
49 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
50 Illuminated pushbutton actuator page 8
51 Illuminated pushbutton actuator page 8
1a-
2
3
4b+
1a-
2b+
13a-
4
2b+
13a-
4
2b+
31x1-
24x2+
I
31
24
II
31
24
III
31
24
IV
31x1-
24x2+
I
31
24
II
31
24
III
31a-
24b+
3(+)
4(-)
I
31
24
II
31a-
24b+
3(+)
4(-)
I
31
24
II
1(-)
2(+)
51
Drawings
54
01.2010
52 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
53 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
54 Illuminated pushbutton actuator page 8
55 Illuminated pushbutton actuator page 8
56 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
57 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
58 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
59 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
31x1-
24x2+
I
31
24
II
31x1-
24x2+
I
31a-
24b+
3(+)
4(-)
I
31a-
24b+
3(+)
4(-)
I
1(-)
2(+)
31x1-
24x2+
I
1a-
2b+
1a-
2
3
4b+
1a-
2b+
51
Drawings
55
01.2010
60 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
61 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14
62 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18
63 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18
64 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18
65 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18
66 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
67 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
13a-
4
2b+
13a-
4
2b+
31
24
C
31
24
B
31
24
C
31
24
B
31
24
C
31
24
B
31
24
C
31
24
B
31
24
I
31
24
I
31
24
II
51
Drawings
56
01.2010
68 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
69 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
70 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
71 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
72 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
73 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
74 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
75 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
31
24
I
31
24
II
31
24
III
31
24
I
31
24
II
31
24
III
31
24
IV
13
4
2
13
4
2
31
24
I
31
24
I
31
24
II
31
24
I
31
24
II
31
24
III
31
24
I
31
24
II
31
24
III
31
24
IV
51
Drawings
57
01.2010
76 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
77 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15
78 Indicator actuator page 7
79 Indicator actuator page 7
13
4
2
13
4
2
b+(x2) 4(-)
a-(x1) 3(+)
b+(x2) 4(-)
a-(x1) 3(+)
2(+)
1(-)
Index from Typ-Nr.
58
01.2010
Typ-Nr. Page Typ-Nr. Page Typ-Nr. Page
01-907 ........................................31
01-928 ........................................29
01-929 ........................................29
02-904.0 .....................................30
02-904.1 .....................................30
02-904.3 .....................................30
02-904.7 .....................................30
02-905 ........................................31
02-912.1 .....................................30
02-912.2 .....................................30
02-912.3 .....................................30
02-912.4 .....................................30
10-1306.1349 .............................29
10-1307.1369 .............................29
10-1309.1309 .............................29
10-1310.1319 .............................29
10-1311.1249 .............................29
10-1312.1229 .............................29
10-1313.1209 .............................29
10-1313.1249 .............................29
10-1316.1179 .............................29
10-1316.1209 .............................29
10-1319.1179 .............................29
10-1319.1199 .............................29
10-2J06.3142 .............................30
10-2J06.3144 .............................30
10-2J06.3145 .............................30
10-2J06.3146 .............................30
10-2J06.3149 .............................30
10-2J09.1062 .............................30
10-2J09.1064 .............................30
10-2J09.1065 .............................30
10-2J09.1066 .............................30
10-2J09.1069 .............................30
10-2J12.1062 .............................30
10-2J12.1064 .............................30
10-2J12.1065 .............................30
10-2J12.1066 .............................30
10-2J12.1069 .............................30
10-2J13.1062 .............................30
10-2J13.1064 .............................30
10-2J13.1065 .............................30
10-2J13.1066 .............................30
10-2J13.1069 .............................30
10-2J19.1042 .............................30
10-2J19.1044 .............................30
10-2J19.1045 .............................30
10-2J19.1046 .............................30
10-2J19.1049 .............................30
31-928 ........................................29
31-929 ........................................29
31-940 ........................................28
31-941 ........................................28
31-942 ........................................28
31-945 ........................................29
31-946 ........................................29
31-985.0 .....................................28
31-989.300 .................................28
31-989.311 .................................28
31-991 ........................................31
51-030.002 ...................................7
51-030.005 ...................................7
51-031.006 ...................................7
51-040.002 ...................................7
51-040.005 ...................................7
51-041.006 ...................................7
51-050.002 ...................................7
51-050.002F ...............................13
51-050.005 ...................................7
51-050.005F ...............................13
51-051.006 ...................................7
51-051.006F ...............................13
51-121.022 ...................................8
51-121.0252 .................................8
51-122.0252 .................................8
51-123.0252 .................................8
51-124.0252 .................................8
51-131.022 ...................................8
51-131.0252 .................................8
51-132.0252 .................................8
51-133.0252 .................................8
51-134.0252 .................................8
51-135.022D ........ ................ .........9
51-135.022DF ............................16
51-135.025D2 ......... .................... ..9
51-135.025D2F ..........................16
51-136.025D2 ......... .................... ..9
51-136.025D2F ..........................16
51-137.025D2 ......... .................... ..9
51-137.025D2F ..........................16
51-138.025D2 ......... .................... ..9
51-138.025D2F ..........................16
51-141.022D ........ ................ .........9
51-141.022DF ............................17
51-141.025D2 ......... .................... ..9
51-141.025D2F ..........................17
51-142.025D2 ......... .................... ..9
51-142.025D2F ..........................17
51-143.025D2 ......... .................... ..9
51-143.025D2F ..........................17
51-144.025D2 ......... .................... ..9
51-144.025D2F ..........................17
51-145.022D ........ ................ .........9
51-145.022DF ............................15
51-145.025D2 ......... .................... ..9
51-145.025D2F ..........................15
51-146.025D2 ......... .................... ..9
51-146.025D2F ..........................15
51-147.025D2 ......... .................... ..9
51-147.025D2F ..........................15
51-148.025D2 ......... .................... ..9
51-148.025D2F ..........................15
51-151.022 ...................................8
51-151.022F ...............................14
51-151.0252 .................................8
51-151.0252F .............................14
51-152.0252 .................................8
51-152.0252F .............................14
51-153.0252 .................................8
51-153.0252F .............................14
51-154.0252 .................................8
51-154.0252F .............................14
51-155.022D ........ ................ .........9
51-155.022DF ............................15
51-155.025D2 ......... .................... ..9
51-155.025D2F ..........................15
51-156.025D2 .............. ................. 9
51-156.025D2F ..........................15
51-157.025D2 .............. ................. 9
51-157.025D2F ..........................15
51-158.025D2 .............. ................. 9
51-158.025D2F ..........................15
51-195.022D ................ ................. 9
51-195.022DF ............................16
51-195.025D2 .............. ................. 9
51-195.025D2F ..........................16
51-196.025D2 .............. ................. 9
51-196.025D2F ..........................16
51-197.025D2 .............. ................. 9
51-197.025D2F ..........................16
51-198.025D2 .............. ................. 9
51-198.025D2F ..........................16
51-235.022D ................ ................. 9
51-235.022DF ............................16
51-235.025D2 .............. ................. 9
51-235.025D2F ..........................16
51-236.025D2 .............. ................. 9
51-236.025D2F ..........................16
51-237.025D2 .............. ................. 9
51-237.025D2F ..........................16
51-238.025D2 .............. ................. 9
51-238.025D2F ..........................16
51-255.022D ................ ................. 9
51-255.022DF ............................15
51-255.025D2 .............. ................. 9
51-255.025D2F ..........................15
51-256.025D2 .............. ................. 9
51-256.025D2F ..........................15
51-257.025D2 .............. ................. 9
51-257.025D2F ..........................15
51-258.025D2 .............. ................. 9
51-258.025D2F ..........................15
51-261.022 ...................................8
51-261.0252 .................................8
51-262.0252 .................................8
51-263.0252 .................................8
51-264.0252 .................................8
51-271.022 ...................................8
51-271.0252 .................................8
51-272.0252 .................................8
51-273.0252 .................................8
51-274.0252 .................................8
51-281.022 ...................................8
51-281.022F ...............................14
51-281.0252 .................................8
51-281.0252F .............................14
51-282.0252 .................................8
51-282.0252F .............................14
51-283.0252 .................................8
51-283.0252F .............................14
51-284.0252 .................................8
51-284.0252F .............................14
51-295.022D ................ ................. 9
51-295.022DF ............................16
51-295.025D2 .............. ................. 9
51-295.025D2F ..........................16
51-296.025D2 .............. ................. 9
51-296.025D2F ..........................16
51-297.025D2 .............. ................. 9
Index from Typ-Nr.
59
01.2010
Typ-Nr. Page Typ-Nr. Page Typ-Nr. Page
51-297.025D2F .......................... 16
51-298.025D2 ..............................9
51-298.025D2F .......................... 16
51-335.022D ................................9
51-335.022DF ............................ 16
51-335.025D2 ..............................9
51-335.025D2F .......................... 16
51-336.025D2 ..............................9
51-336.025D2F .......................... 16
51-337.025D2 ..............................9
51-337.025D2F .......................... 16
51-338.025D2 ..............................9
51-338.025D2F .......................... 16
51-355.022D ................................9
51-355.022DF ............................ 15
51-355.025D2 ..............................9
51-355.025D2F .......................... 15
51-356.025D2 ..............................9
51-356.025D2F .......................... 15
51-357.025D2 ..............................9
51-357.025D2F .......................... 15
51-358.025D2 ..............................9
51-358.025D2F .......................... 15
51-361.022D ..............................10
51-361.022DF ............................ 18
51-362.022D ..............................10
51-362.022DF ............................ 18
51-363.022D ..............................10
51-363.022DF ............................ 18
51-364.022D ..............................10
51-364.022DF ............................ 18
51-365.022D ..............................10
51-365.022DF ............................ 18
51-366.022D ..............................10
51-366.022DF ............................ 18
51-367.022D ..............................10
51-367.022DF ............................ 18
51-368.022D ..............................10
51-368.022DF ............................ 18
51-371.022D ..............................10
51-371.022DF ............................ 18
51-372.022D ..............................10
51-372.022DF ............................ 18
51-373.022D ..............................10
51-373.022DF ............................ 18
51-374.022D ..............................10
51-374.022DF ............................ 18
51-375.022D ..............................10
51-375.022DF ............................ 18
51-376.022D ..............................10
51-376.022DF ............................ 18
51-377.022D ..............................10
51-377.022DF ............................ 18
51-378.022D ..............................10
51-378.022DF ............................ 18
51-381.022D ..............................10
51-381.022DF ............................ 18
51-382.022D ..............................10
51-382.022DF ............................ 18
51-383.022D ..............................10
51-383.022DF ............................ 18
51-384.022D ..............................10
51-384.022DF ............................ 18
51-385.022D ..............................10
51-385.022DF ............................18
51-386.022D ..............................10
51-386.022DF ............................18
51-387.022D ..............................10
51-387.022DF ............................18
51-388.022D ..............................10
51-388.022DF ............................18
51-395.022D ................................9
51-395.022DF ............................16
51-395.025D2 ..............................9
51-395.025D2F ..........................16
51-396.025D2 ..............................9
51-396.025D2F ..........................16
51-397.025D2 ..............................9
51-397.025D2F ..........................16
51-398.025D2 ..............................9
51-398.025D2F ..........................16
51-401.036D ................................9
51-401.036DF ............................16
51-402.036D ................................9
51-402.036DF ............................16
51-404.036D ................................9
51-404.036DF ............................16
51-405.036D ................................9
51-405.036DF ............................16
51-407.036D ................................9
51-407.036DF ............................16
51-408.036D ................................9
51-408.036DF ............................16
51-411.036D ................................9
51-411.036DF ............................16
51-412.036D ................................9
51-412.036DF ............................16
51-414.036D ................................9
51-414.036DF ............................16
51-415.036D ................................9
51-415.036DF ............................16
51-417.036D ................................9
51-417.036DF ............................16
51-418.036D ................................9
51-418.036DF ............................16
51-421.036 ................................... 8
51-422.036 ................................... 8
51-423.036 ................................... 8
51-425.036 ................................... 8
51-426.036 ................................... 8
51-427.036D ................................9
51-427.036DF ............................16
51-428.036D ................................9
51-428.036DF ............................16
51-431.036 ................................... 8
51-432.036 ................................... 8
51-433.036 ................................... 8
51-435.036 ................................... 8
51-436.036 ................................... 8
51-437.036D ................................9
51-437.036DF ............................17
51-438.036D ................................9
51-438.036DF ............................17
51-441.036D ................................9
51-441.036DF ............................15
51-442.036D ................................9
51-442.036DF ............................15
51-444.036D ................................9
51-444.036DF ............................15
51-445.036D ................................9
51-445.036DF ............................15
51-447.036D ................................9
51-447.036DF ............................15
51-448.036D ................................9
51-448.036DF ............................15
51-451.036 ...................................8
51-451.036F ............................... 14
51-452.036 ...................................8
51-452.036F ............................... 14
51-453.036 ...................................8
51-453.036F ............................... 14
51-455.036 ...................................8
51-455.036F ............................... 14
51-456.036 ...................................8
51-456.036F ............................... 14
51-457.036D ................................9
51-457.036DF ............................15
51-458.036D ................................9
51-458.036DF ............................15
51-461.036 ...................................8
51-462.036 ...................................8
51-463.036 ...................................8
51-465.036 ...................................8
51-466.036 ...................................8
51-471.036 ...................................8
51-472.036 ...................................8
51-473.036 ...................................8
51-475.036 ...................................8
51-476.036 ...................................8
51-481.036 ...................................8
51-481.036F ............................... 14
51-482.036 ...................................8
51-482.036F ............................... 14
51-483.036 ...................................8
51-483.036F ............................... 14
51-485.036 ...................................8
51-485.036F ............................... 14
51-486.036 ...................................8
51-486.036F ............................... 14
51-495.022D ................................9
51-495.022DF ............................16
51-495.025D2 ..............................9
51-495.025D2F ..........................16
51-496.025D2 ..............................9
51-496.025D2F ..........................16
51-497.025D2 ..............................9
51-497.025D2F ..........................16
51-498.025D2 ..............................9
51-498.025D2F ..........................16
51-701.006 ...................................7
51-702.006 ...................................7
51-703.006 ...................................7
51-704.006 ...................................7
51-705.0292 .................................8
51-706.0292 .................................8
51-707.0292 .................................8
51-708.0292 .................................8
51-709.0292 .................................8
51-710.0292 .................................8
Index from Typ-Nr.
60
01.2010
Typ-Nr. Page Typ-Nr. Page Typ-Nr. Page
51-711.0292 .................................8
51-712.0292 .................................8
51-713.0292 .................................8
51-714.0292 .................................8
51-715.0292 .................................8
51-716.0292 .................................8
51-717.0292 .................................8
51-718.0292 .................................8
51-719.0292 .................................8
51-720.0292 .................................8
51-741.006 ...................................7
51-742.006 ...................................7
51-743.0292 .................................8
51-744.0292 .................................8
51-745.0292 .................................8
51-746.0292 .................................8
51-747.0292 .................................8
51-748.0292 .................................8
51-749.0292 .................................8
51-750.0292 .................................8
51-901.0 .....................................21
51-901.2 .....................................21
51-901.3 .....................................21
51-901.4 .....................................21
51-901.5 .....................................21
51-901.6 .....................................21
51-901.8 .....................................21
51-901.9 .....................................21
51-903.1 .....................................21
51-903.2 .....................................21
51-903.3 .....................................21
51-903.4 .....................................21
51-903.5 .....................................21
51-903.6 .....................................21
51-903.7 .....................................21
51-904.2 .....................................21
51-904.3 .....................................21
51-904.4 .....................................21
51-904.5 .....................................21
51-904.6 .....................................21
51-904.7 .....................................21
51-905.2 .....................................21
51-905.4 .....................................21
51-905.5 .....................................21
51-905.7 .....................................21
51-906.2 .....................................21
51-906.4 .....................................21
51-906.5 .....................................21
51-906.7 .....................................21
51-910 ........................................31
51-920 ........................................27
51-925 ........................................27
51-931.0 .....................................21
51-931.2 .....................................21
51-931.3 .....................................21
51-931.4 .....................................21
51-931.5 .....................................21
51-931.6 .....................................21
51-931.8 .....................................21
51-931.9 .....................................21
51-933.1 .....................................21
51-933.2 .....................................21
51-933.3 .....................................21
51-933.4 .....................................21
51-933.5 .....................................21
51-933.6 .....................................21
51-933.7 .....................................21
51-935.2 .....................................21
51-935.4 .....................................21
51-935.5 .....................................21
51-935.7 .....................................21
51-938 ........................................31
51-943.0 .....................................28
51-943.1 .....................................29
51-943.9 .....................................32
51-947.0 .....................................27
51-948.0 .....................................27
51-949.0 .....................................27
51-951.0 .....................................21
51-951.2 .....................................21
51-951.3 .....................................21
51-951.4 .....................................21
51-951.5 .....................................21
51-951.6 .....................................21
51-951.8 .....................................21
51-951.9 .....................................21
51-953.1 .....................................21
51-953.2 .....................................21
51-953.3 .....................................21
51-953.4 .....................................21
51-953.5 .....................................21
51-953.6 .....................................21
51-953.7 .....................................21
51-954.2 .....................................21
51-954.3 .....................................21
51-954.4 .....................................21
51-954.5 .....................................21
51-954.6 .....................................21
51-954.7 .....................................21
51-955.2 .....................................21
51-955.4 .....................................21
51-955.5 .....................................21
51-955.7 .....................................21
52-131.022 .................................11
52-131.022 .................................19
52-131.0252 ...............................11
52-131.0252 ...............................19
52-132.0252 ...............................11
52-132.0252 ...............................19
52-133.0252 ...............................11
52-133.0252 ...............................19
52-134.0252 ...............................11
52-134.0252 ...............................19
52-271.022 .................................11
52-271.022 .................................19
52-271.0252 ...............................11
52-271.0252 ...............................19
52-272.0252 ...............................11
52-272.0252 ...............................19
52-273.0252 ...............................11
52-273.0252 ...............................19
52-274.0252 ...............................11
52-274.0252 ...............................19
52-431.036 .................................11
52-431.036 .................................19
52-432.036 .................................11
52-432.036 .................................19
52-433.036 .................................11
52-433.036 .................................19
52-435.036 .................................11
52-435.036 .................................19
52-436.036 .................................11
52-436.036 .................................19
52-471.036 .................................11
52-471.036 .................................19
52-472.036 .................................11
52-472.036 .................................19
52-473.036 .................................11
52-473.036 .................................19
52-475.036 .................................11
52-475.036 .................................19
52-476.036 .................................11
52-476.036 .................................19
52-571.022A ...............................12
52-571.022A ...............................20
52-572.022A ...............................12
52-572.022A ...............................20
52-573.022A ...............................12
52-573.022A ...............................20
52-574.022A ...............................12
52-574.022A ...............................20
52-743.0292 ...............................11
52-744.0292 ...............................11
52-745.0292 ...............................11
52-746.0292 ...............................11
52-747.0292 ...............................11
52-748.0292 ...............................11
52-749.0292 ...............................11
52-750.0292 ...............................11
52-928.0 .....................................24
52-928.20 ...................................24
52-928.30 ...................................24
52-928.40 ...................................24
52-928.50 ...................................24
52-928.60 ...................................24
52-929.20 ...................................24
52-929.30 ...................................24
52-929.40 ...................................24
52-929.50 ...................................24
52-929.60 ...................................24
52-929.8 .....................................24
52-929.9 .....................................24
52-950.0 .....................................23
52-952.0 .....................................23
61-9028.0 ...................................24
61-9028.20 .................................24
61-9028.30 .................................24
61-9028.40 .................................24
61-9028.50 .................................24
61-9028.60 .................................24
61-9028.9 ...................................24
61-9029.20 .................................24
61-9029.30 .................................24
61-9029.40 .................................24
61-9029.50 .................................24
61-9029.60 .................................24
61-9029.8 ...................................24
61-9029.9 ...................................24
61-9451.0 ...................................27
Index from Typ-Nr.
61
01.2010
Typ-Nr. Page Typ-Nr. Page Typ-Nr. Page
61-9452.0 ...................................27
61-9453.0 ...................................27
61-9593.0 ...................................23
61-9593.2 ...................................23
61-9593.4 ...................................23
61-9593.5 ...................................23
61-9642.1 ...................................21
61-9642.2 ...................................21
61-9642.3 ...................................21
61-9642.4 ...................................21
61-9642.5 ...................................21
61-9642.6 ...................................21
61-9642.7 ...................................21
61-9643.201 ...............................22
61-9643.202 ...............................22
61-9643.203 ...............................22
61-9643.301 ...............................22
61-9643.401 ...............................22
61-9643.501 ...............................22
61-9643.502 ...............................22
61-9643.503 ...............................22
61-9643.601 ...............................22
61-9643.602 ...............................22
61-9643.603 ...............................22
61-9643.701 ...............................22
61-9643.702 ...............................22
61-9643.703 ...............................22
61-9671.1 ...................................21
61-9671.2 ...................................21
61-9671.3 ...................................21
61-9671.4 ...................................21
61-9671.5 ...................................21
61-9671.6 ...................................21
61-9671.7 ...................................21
61-9681.1 ...................................21
61-9681.2 ...................................21
61-9681.3 ...................................21
61-9681.4 ...................................21
61-9681.5 ...................................21
61-9681.6 ...................................21
61-9681.7 ...................................21
61-9707.7 ...................................22
61-9730.0 ...................................31
61-9740.0 ...................................31
61-9771.0 ...................................21
61-9771.8 ...................................21
61-9771.9 ...................................21
61-9781.0 ...................................21
61-9781.8 ...................................21
61-9781.9 ...................................21
61-9841.0 ...................................23
61-9841.0A ................................22
61-9841.2 ...................................23
61-9841.2A ................................22
61-9841.4 ...................................23
61-9841.4A ................................22
61-9841.5 ...................................23
61-9841.5A ................................22
61-9841.6 ...................................23
61-9841.6A ................................22
61-9841.8 ...................................23
61-9841.8A ................................22
61-9842.0 ...................................23
61-9842.2 ................................... 23
61-9842.4 ................................... 23
61-9842.5 ................................... 23
61-9842.6 ................................... 23
61-9842.8 ................................... 23
61-9921.0 ................................... 27
61-9922.0 ................................... 27
61-9924.0 ................................... 27
61-9927.2 ................................... 26
61-9930.0 ................................... 25
61-9930.0 ................................... 26
61-9930.4 ................................... 25
61-9930.4 ................................... 26
61-9931.0 ................................... 25
61-9931.0 ................................... 26
61-9931.4 ................................... 25
61-9931.4 ................................... 26
61-9932.0 ................................... 26
61-9932.0 ................................... 26
61-9932.1 ................................... 26
61-9932.1 ................................... 26
61-9932.10 ................................. 26
61-9932.10 ................................. 26
61-9932.2 ................................... 26
61-9932.2 ................................... 26
61-9932.4 ................................... 26
61-9932.4 ................................... 26
61-9932.5 ................................... 26
61-9932.5 ................................... 26
61-9932.6 ................................... 26
61-9932.6 ................................... 26
61-9933.0 ................................... 25
61-9933.0 ................................... 25
61-9933.1 ................................... 25
61-9933.1 ................................... 25
61-9933.10 ................................. 25
61-9933.10 ................................. 25
61-9933.2 ................................... 25
61-9933.2 ................................... 25
61-9933.4 ................................... 25
61-9933.4 ................................... 25
61-9933.5 ................................... 25
61-9933.5 ................................... 25
61-9933.6 ................................... 25
61-9933.6 ................................... 25
61-9934.8 ................................... 25
61-9936.0 ................................... 26
61-9980.0 ................................... 24
704.968.0 ...................................25
704.968.1 ...................................25
84-9103.7 ................................... 26
EAO AG
Tannwaldstrasse 88
4601 Olten, Switzerland
E-mail info@eao.com
Website www.eao.com
Austria
Phone +49 201 85 87 0
Fax +49 201 85 87 210
E-mail sales.ede@eao.com
Belgium
Phone +32 3 777 82 36
Fax +32 3 777 84 19
E-mail sales.ebl@eao.com
China
Phone +852 27 86 91 41
Fax +852 27 86 95 61
E-mail sales.ehk@eao.com
France
Phone +33 1 64 43 37 37
Fax +33 1 64 43 37 49
E-mail sales.ese@eao.com
Germany
Phone +49 201 85 87 0
Fax +49 201 85 87 210
E-mail sales.ede@eao.com
Italy
Phone +39 035 481 0189
Fax +39 035 481 3786
E-mail sales.eit@eao.com
Japan
Phone +81 3 5444 5411
Fax +81 3 5444 0345
E-mail sales.esj@eao.com
Netherlands
Phone +31 78 653 17 00
Fax +31 78 653 17 99
E-mail sales.enl@eao.com
Sweden
Phone +46 8 683 86 60
Fax +46 8 724 29 12
E-mail sales.esw@eao.com
Switzerland
Phone +41 62 388 95 00
Fax +41 62 388 95 55
E-mail sales.ech@eao.com
United Kingdom
Phone +44 1444 236 000
Fax +44 1444 236 641
E-mail sales.euk@eao.com
USA
Phone +1 203 877 4577
Fax +1 203 877 3694
E-mail sales.eus@eao.com
Other Countries
Phone +41 62 286 92 10
Fax +41 62 296 21 62
E-mail info@eao.com
EAO reserves the right to alter specifications without further notice
