Data Sheet April 19, 2011 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 to 3.63Vdc output; 30A Output Current 6.0 - 14Vdc input; 0.8dc to 5.5Vdc output; 25A Output Current RoHS Compliant Features Compliant to RoHS EU Directive 2002/95/EC (Z versions) Compliant to ROHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) Delivers up to 30A of output current High efficiency - 93% 3.3V full load (VIN=12Vdc) Available in two input voltage ranges ATH: 4.5 to 5.5Vdc ATS: 6.0 to 14Vdc Applications ATH: 0.8 to 3.63Vdc ATS: 0.8 to 5.5Vdc Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Output voltage programmable from Small size and low profile: 50.8 mm x 12.7 mm x 14.0 mm 2.00 in. x 0.50 in. x 0.55 in. Monotonic start-up into pre-biased output UL* 60950 Recognized, CSA C22.2 No. 60950-00 Certified, and VDE 0805 (EN60950-1 rd 3 edition) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Output voltage sequencing (EZ-SEQUENCE TM ) Remote On/Off Remote Sense Over current and Over temperature protection Parallel operation with active current sharing Wide operating temperature range (-40C to 85C) Description The Austin MegaLynx series SIP power modules are non-isolated DC-DC converters in an industry standard package that can deliver up to 30A of output current with a full load efficiency of 92% at 3.3Vdc output voltage (VIN = 12Vdc). The ATH series of modules operate off an input voltage from 4.5 to 5.5Vdc and provide an output voltage that is programmable from 0.8 to 3.63Vdc, while the ATS series of modules have an input voltage range from 6 to 14V and provide a programmable output voltage ranging from 0.8 to 5.5Vdc. Both series have a sequencing feature that enables designers to implement various types of output voltage sequencing when powering multiple modules on the board. Additional features include remote On/Off, adjustable output voltage, remote sense, over current, over temperature protection and active current sharing between modules. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS05-012 ver. 1.06 PDF Name: austin_megalynx_sip.pdf Data Sheet April 19, 2011 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage All VIN -0.3 15 Vdc Sequencing pin voltage Continuous All VsEQ -0.3 15 Vdc Operating Ambient Temperature All TA -40 85 C All Tstg -55 125 C (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit VIN 4.5 5.0 5.5 Vdc ATS VIN 6.0 12 14 Vdc ATH IIN,max 27 Adc ATS IIN,max 26 Adc Inrush Transient All 2 1 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN=6.0V to 14.0V, IO= IOmax ; See Figure 1) All 100 mAp-p Input Ripple Rejection (120Hz) All 50 dB Operating Input Voltage ATH Maximum Input Current (VIN= VIN,min , VO= VO,set, IO=IO, max) LINEAGE POWER I t 2 2 Data Sheet April 19, 2011 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -1.5 +1.5 % VO, set All VO, set -3.0 +3.0 % VO, set ATH VO 0.8 3.63 Vdc ATS VO 0.8 5.5 Vdc (VIN=VIN,min, IO=IO, max, Tref=25C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All 0.1 % VO, set Load (IO=IO, min to IO, max) All 0.4 % VO, set Temperature (Tref=TA, min to TA, max) All 1 % VO, set 50 mVpk-pk 0.5 Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max COUT = 0.01F // 0.1F // 10F ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) Vo 2.5V 2.5V < Vo 3.63V Vo > 3.63V 75 mVpk-pk 100 mVpk-pk External Capacitance ESR 1 m All CO, max 0 2,000 F ESR 10 m All CO, max 0 10,000 F ATH025/ATS025 Io 0 25 Adc ATH030 Io 0 30 Adc Output Current Limit Inception (Hiccup Mode) All IO, lim 120 % Iomax Output Short-Circuit Current All IO, s/c 20 % Iomax Output Current (VIN = 5Vdc/12Vdc) Output Current (VIN = 5Vdc) (VO250mV) ( Hiccup Mode ) Efficiency VO,set = 0.8dc 82.0 % VIN=12Vdc, TA=25C VO,set = 1.2Vdc 84.0 % IO=25A , VO= VO,set VO,set = 1.5Vdc 88.0 % VO,set = 1.8Vdc 89.5 % VO,set = 2.5Vdc 91.0 % VO,set = 3.3Vdc 92.5 % Efficiency VIN=5Vdc, TA=25C IO=30A , VO= VO,set Switching Frequency, Fixed LINEAGE POWER VO,set = 5.0Vdc 94.0 % VO,set = 0.8dc 84.0 % VO,set = 1.2Vdc 88.5 % VO,set = 1.5Vdc 90.0 % VO,set = 1.8Vdc 91.0 % VO,set = 2.5Vdc 93.0 % VO,set = 3.3Vdc All fsw 95.0 300 % kHz 3 Data Sheet April 19, 2011 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit (dIO/dt=5A/s; VIN=VIN, nom; VO=3.3V; TA=25C;) Load Change from Io= 0% to 50% of IO,max; No external output capacitors Peak Deviation ATS Vpk 350 mV Settling Time (VO<10% peak deviation) ATS ts 20 s (dIO/dt=5A/s; VIN=VIN, nom; VO=3.3V; TA=25C;) Load Change from IO= 50% to 0%of IO, max: No external output capacitors Peak Deviation ATS Vpk 350 mV Settling Time (VO<10% peak deviation) Dynamic Load Response ATS ts 20 s (dIO/dt=5A/s; VIN=VIN, nom; VO=3.3V; TA=25C;) Load Change from Io= 0% to 50% of IO,max; No external output capacitors Peak Deviation ATH Vpk 320 mV Settling Time (VO<10% peak deviation) ATH ts 20 s (dIO/dt=5A/s; VIN=VIN, nom; VO=3.3V; TA=25C) Load Change from IO= 50% to 0%of IO, max: No external output capacitors Peak Deviation ATH Vpk 250 mV Settling Time (VO<10% peak deviation) ATH ts 20 s General Specifications Parameter Min Calculated MTBF (VIN= VIN, nom, IO= 0.8IO, max, TA=40C) Telecordia SR 332 Issue 1: Method 1, case 3 Weight LINEAGE POWER Typ Max 3,016,040 7.4 Unit Hours g 4 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to GND) Logic High (Module OFF) Input High Current All IIH 0.5 3.3 mA Input High Voltage All VIH 3.0 VIN, max V Logic Low (Module ON) Input Low Current All IIL 200 A Input Low Voltage All VIL -0.3 1.2 V All Tdelay 3 msec All Tdelay 3 msec All Trise 4 msec Turn-On Delay and Rise Times (VIN=VIN, nom, IO=IO, max , VO to within 1% of steady state) Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = 10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo = 10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) Output voltage overshoot 3.0 % VO, set o IO = IO, max; VIN, min - VIN, max, TA = 25 C Remote Sense Range Over Temperature Protection All 0.5 V 125 C -- 2 V/msec All Tref All dVSEQ/dt to application of voltage on SEQ pin) All TsEQ-delay Tracking Accuracy All |VSEQ -Vo,set| 100 200 mV |VSEQ -Vo,set| 200 400 mV (See Thermal Consideration section) Sequencing Slew rate capability (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) Sequencing Delay time (Delay from VIN, min Power-up (2V/ms) Power-down (1V/ms) 10 msec (VIN, min to VIN, max; IO, min - IO, max VSEQ < Vo,set) Input Undervoltage Lockout Turn-on Threshold ATH 4.3 Vdc Turn-off Threshold ATH 3.9 Vdc Turn-on Threshold ATS 5.5 Vdc Turn-off Threshold ATS 5.0 Vdc Forced Load Share Accuracy -P Number of units in Parallel -P LINEAGE POWER 10 % Io 5 5 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves The following figures provide typical characteristics for the ATS025A0X (0.8V, 25A) at 25oC. 30 92% OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 89% 86% 83% 80% 77% VIN = 6.0V 74% VIN = 12.0V 71% VIN =14.0V 68% 0 5 10 15 20 1.5m/s (300 LFM ) 5 2.0m/s (400 LFM ) 0 30 40 50 60 70 80 90 VO (V) (0.5V/div) VOn/off (V) (5V/div) OUTPUT VOLTAGE Figure 4. Derating Output Current versus Local Ambient Temperature and Airflow. On/Off VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (2ms/div) OUTPUT VOLTAGE VO (V) (0.5V/div) VIN (V) (5V/div) Figure 5. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (10A/div) OUTPUT CURRENT, OUTPUT VOLTAGE LINEAGE POWER 1.0m/s (200 LFM ) 10 O TIME, t (1s/div) Figure 3. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. 0.5m/s (100 LFM ) 15 AMBIENT TEMPERATURE, TA C Figure 1. Converter Efficiency versus Output Current. TIME, t (5s /div) 20 20 25 OUTPUT CURRENT, IO (A) Figure 2. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 25 TIME, t (2ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 6 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves o The following figures provide typical characteristics for the ATS025A0X (1.8V, 25A) at 25 C. 96% 30 OUTPUT CURRENT, Io (A) 93% EFFICIENCY, (%) 90% 87% 84% 81% VIN = 6.0V 78% VIN = 12.0V 75% VIN =14.0V 72% 0 5 10 15 20 LINEAGE POWER 1.0m/ s (200 LFM ) 10 1.5m/s (300 LFM ) 5 2.0m/ s (400 LFM ) 0 30 40 50 60 70 80 90 O OUTPUT VOLTAGE VO (V) (0.5V/div) VOn/off (V) (5V/div) Figure 10. Derating Output Current versus Local Ambient Temperature and Airflow ((VIN = VIN,NOM). On/Off VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (2ms/div) OUTPUT VOLTAGE VO (V) (0.5V/div) VIN (V) (5V/div) Figure 11. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (5A/div) OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (5s /div) Figure 9. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. 0.5m/s (100 LFM ) 15 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) Figure 8. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 20 20 25 OUTPUT CURRENT, IO (A) Figure 7. Converter Efficiency versus Output Current. 25 TIME, t (2ms/div) Figure 12. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 7 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves The following figures provide typical characteristics for the ATS025A0X (3.3V, 25A) at 25oC. 30 99% OUTPUT CURRENT, Io (A) 96% EFFICIENCY, (%) 93% 90% 87% 84% VIN = 6.0V 81% VIN = 12.0V 78% VIN =14.0V 75% 0 5 10 15 20 LINEAGE POWER 1.0m/s (200 LFM ) 10 1.5m/s (300 LFM ) 5 2.0m/s (400 LFM ) 0 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA C VO (V) (1V/div) VOn/off (V) (5V/div) OUTPUT VOLTAGE Figure 16. Derating Output Current versus Local Ambient Temperature and Airflow. On/Off VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (2ms/div) OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (5V/div) Figure 17. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (10A/div) OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (5s /div) Figure 15. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. 0.5m/s (100 LFM ) 15 O TIME, t (1s/div) Figure 14. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 20 20 25 OUTPUT CURRENT, IO (A) Figure 13. Converter Efficiency versus Output Current. 25 TIME, t (2ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 8 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves o The following figures provide typical characteristics for the ATH030A0X (0.8V, 30A) at 25 C. 35 92% 89% OUTPUT CURRENT, Io (A) 30 EFFICIENCY, (%) 86% 83% 80% 77% VIN = 4.5V 74% VIN = 5.0V 71% VIN =5.5V 68% 0 6 12 18 24 25 0.5m/s (100 LFM ) 20 1.0m/s (200 LFM ) 15 1.5m/s (300 LFM ) 10 2.0m/s (400 LFM ) 5 20 30 30 40 50 60 70 80 On/Off VOLTAGE OUTPUT VOLTAGE VOn/off (V) (2V/div) VO (V) (0.5V/div) VO (V) (20mV/div) Figure 22. Derating Output Current versus Local Ambient Temperature and Airflow. OUTPUT VOLTAGE AMBIENT TEMPERATURE, TA C Figure 19. Converter Efficiency versus Output Current. TIME, t (2ms/div) TIME, t (1s/div) TIME, t (10s /div) Figure 21. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. LINEAGE POWER OUTPUT VOLTAGE VO (V) (0.5V/div) VIN (V) (2V/div) Figure 23. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (10A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 20. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 90 O OUTPUT CURRENT, IO (A) TIME, t (2ms/div) Figure 24. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 9 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves The following figures provide typical characteristics for the ATH030A0X (1.8V, 30A) at 25oC. 96% 35 OUTPUT CURRENT, Io (A) 93% EFFICIENCY, (%) 90% 87% 84% 81% VIN = 4.5V 78% VIN = 5.0V 75% VIN =5.5V 72% 0 6 12 18 24 30 25 0.5m/s (100 LFM ) 20 1.0m/ s (200 LFM ) 15 1.5m/s (300 LFM ) 10 2.0m/ s (400 LFM ) 5 20 30 30 40 50 60 70 80 90 O Figure 28. Derating Output Current versus Local Ambient Temperature and Airflow. VO (V) (20mV/div) Figure 25. Converter Efficiency versus Output Current. On/Off VOLTAGE OUTPUT VOLTAGE VOn/off (V) (2V/div) VO (V) (0.5V/div) AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE OUTPUT CURRENT, IO (A) TIME, t (2ms/div) TIME, t (1s/div) Figure 27. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. LINEAGE POWER OUTPUT VOLTAGE VO (V) (0.5V/div) VIN (V) (2V/div) TIME, t (10s /div) Figure 29. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (10A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 26. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). TIME, t (2ms/div) Figure 30. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 10 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Characteristic Curves o The following figures provide typical characteristics for the ATH030A0X (3.3V, 30A) at 25 C. 99% 35 OUTPUT CURRENT, Io (A) 96% EFFICIENCY, (%) 93% 90% 87% 84% VIN = 4.5V 81% VIN = 5.0V 78% VIN =5.5V 75% 0 6 12 18 24 1.5m/s (300 LFM ) 10 2.0m/s (400 LFM ) 5 30 40 50 60 70 80 90 O Figure 34. Derating Output Current versus Local Ambient Temperature and Airflow. TIME, t (2ms/div) TIME, t (10s /div) Figure 33. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. VO (V) (1V/div) VIN (V) (2V/div) OUTPUT VOLTAGE Figure 35. Typical Start-up Using Remote On/Off (VIN = VIN,NOM, Io = Io,max). INPUT VOLTAGE VO (V) (100mV/div) IO (A) (10A/div) 1.0m/ s (200 LFM ) 15 On/Off VOLTAGE OUTPUT VOLTAGE VOn/off (V) (2V/div) VO (V) (1V/div) VO (V) (20mV/div) OUTPUT VOLTAGE Figure 32. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). OUTPUT CURRENT, OUTPUT VOLTAGE 0.5m/ s (100 LFM ) 20 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) LINEAGE POWER 25 20 30 OUTPUT CURRENT, IO (A) Figure 31. Converter Efficiency versus Output Current. 30 TIME, t (2ms/div) Figure 36. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 11 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Test Configurations Design Considerations CURRENT PROBE TO OSCILLOSCOPE LTEST VIN(+) BATTERY 1H CS CIN 220F Min 150F E.S.R.<0.1 @ 20C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. The Austin MegaLynxTM module should be connected to a low-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. To minimize input voltage ripple, low-ESR ceramic capacitors are recommended at the input of the module. Figure 41 shows the input ripple voltage for various output voltages at 25A of load current with 2x22 F or 4x22 F ceramic capacitors and an input of 12V. Figure 42 shows data for the 5Vin case, with 2x47F and 4x47F of ceramic capacitors at the input, and for a load current of 30A. Figure 37. Input Reflected Ripple Current Test Setup. COPPER STRIP RESISTIVE LOAD SCOPE GND 0.01uF 0.1uF 10uF GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 38. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact VIN(+) Rdistribution RLOAD VO VIN Rcontact Rcontact COM Rdistribution COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. 2 x 22uF 140 4 x 22uF 120 100 80 60 40 20 0 1.5 2 2.5 3 3.5 4 4.5 5 5.5 60 2 x 47uF 50 4 x 47uF 40 30 20 10 0 0.5 Figure 40. Output Voltage and Efficiency Test Setup. 1 Output Voltage (Vdc) Figure 41. Input ripple voltage for various output voltages with 2x22 F or 4x22 F ceramic capacitors at the input (25A load). Input voltage is 12V. Rdistribution VO 160 0.5 Input Ripple Voltage (mVp-p) VO (+) Input Ripple Voltage (mVp-p) 180 1 1.5 2 2.5 3 3.5 Output Voltage (Vdc) VO. IO Efficiency = LINEAGE POWER VIN. IIN x 100 % Figure 42. Input ripple voltage in mV, p-p for various output voltages with 2x47 F or 4x47 F ceramic capacitors at the input (25A load). Input voltage is 5V. 12 Austin MegaLynxTM Non-Isolated dc-dc Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 due to undervoltage lockout or over temperature protection. Safety Considerations For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950, CSA C22.2 No. 60950-00, EN60950 (VDE 0850) (IEC60950, 3rd edition) Licensed. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. Feature Descriptions Remote On/Off The Austin MegaLynx power modules feature a On/Off pin for remote On/Off operation. If not using the On/Off pin, connect the pin to ground (the module will be ON). The On/Off signal (Von/off) is referenced to ground. Circuit configuration for remote On/Off operation of the module using the On/Off pin is shown in Figure 43. Remote Sense The Austin MegaLynx SIP power modules have a remote sense feature to minimize the effects of distribution losses by regulating the voltage at the remote sense pin (See Figure 44). The voltage between the Sense pin and the Vo pin must not exceed 0.5V. The amount of power delivered by the module is defined as the output voltage multiplied by the output current (Vo x Io). When using Remote Sense, the output voltage of the module can increase, which if the same output is maintained, increases the power output from the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. When the Remote Sense feature is not being used, connect the Remote Sense pin to output of the module. R d istribu tio n R c o n ta c t R c o nta c t V IN (+ ) R d istribu tio n VO Sense During a Logic High on the On/Off pin (transistor Q1 is OFF), the module remains OFF. The external resistor R1 should be chosen to maintain 3.0V minimum on the On/Off pin to ensure that the module is OFF when transistor Q1 is in the OFF state. Suitable values for R1 are 4.7K for input voltage of 12V and 3K for 5Vin. During Logic-Low when Q1 is turned ON, the module is turned ON. VIN + MODULE R1 Therm al SD I ON/OFF ON /OFF 1K + VON/OFF PW M Enable 100K Q1 R LO AD R d istribu tio n R c o n ta c t R c o nta c t COM R d istribu tio n COM Figure 44. Effective Circuit Configuration for Remote Sense operation. Over Current Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The average output current during hiccup is 20% IO, max. 10K GN D _ Figure 43. Remote On/Off Implementation using ON/OFF. The On/Off pin can also be used to synchronize the output voltage start-up and shutdown of multiple modules in parallel. By connecting together the On/Off pins of multiple modules, the output start-up can be synchronized (please refer to characterization curves). When On/Off pins are connected together, all modules will shut down if any one of the modules gets disabled LINEAGE POWER Over Temperature Protection To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will o shutdown if the overtemperature threshold of 130 C is exceeded at the thermal reference point Tref . The thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. 13 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Input Under Voltage Lockout Table 1 At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Output Voltage Programming The output voltage of the Austin MegaLynx can be programmed to any voltage from 0.8dc to 5.0Vdc by connecting a resistor (shown as Rtrim in Figure 45) between Trim and GND pins of the module. Without an external resistor between Trim and GND pins, the output of the module will be 0.8Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, use the following equation: 1200 Rtrim = - 100 Vo - 0.80 Rtrim is the external resistor in Vo is the desired output voltage By using a 0.5% tolerance trim resistor with a TC of 100ppm, a set point tolerance of 1.5% can be achieved as specified in the electrical specification. Table 1 provides Rtrim values required for some common output voltages. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, helps determine the required external trim resistor needed for a specific output voltage. V IN(+) V O(+) ON/OFF TRIM LOAD VO, set (V) 0.8 1.0 1.2 1.5 1.8 2.5 3.3 5.0 Rtrim () Open 5900 2900 1614 1100 606 380 186 Voltage Margining Output voltage margining can be implemented in the Austin MegaLynx modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to output pin for margining-down. Figure 46 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local Lineage Power technical representative for additional details. Voltage Sequencing The Austin MegaLynx series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either leave the SEQ pin unconnected or tied to VIN. Vo Rmargin-down Rtrim GND Austin Lynx or Lynx II Series Q2 Figure 45. Circuit configuration to program output voltage using an external resistor. Trim Rmargin-up Rtrim Q1 GND Figure 46. Circuit Configuration for margining Output voltage. LINEAGE POWER 14 Data Sheet April 19, 2011 Austin MegaLynxTM Non-Isolated dc-dc Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current For proper voltage sequencing, first, input voltage is applied to the module. The On/Off pin of the module is left unconnected or tied to GND for negative logic modules so that the module is ON by default. After applying input voltage to the module, a delay of 10msec minimum is required before applying voltage on the SEQ pin. During this delay time, the SEQ pin should be kept at a voltage of 50mV ( 20 mV). After the 10msec delay, the voltage applied to the SEQ pin is allowed to vary and the output voltage of the module will track this voltage on a one-to-one volt basis until the output reaches the setpoint voltage. To initiate simultaneous shutdown of the modules, the sequence pin voltage is lowered in a controlled manner. The output voltages of the modules track the sequence pin voltage when it falls below their set-point voltages. A valid input voltage must be maintained until the tracking and output voltages reach zero to ensure a controlled shutdown of the modules. For a more detailed description of sequencing, please refer to Application Note AN04-008 titled "Guidelines for Sequencing of Multiple Modules". When using the EZ-SEQUENCETM feature to control start-up of the module, pre-bias immunity feature during start-up is disabled. The pre-bias immunity feature of the module relies on the module being in the diode-mode during start-up. When using the EZ-SEQUENCETM feature, modules goes through an internal set-up time of 10msec, and will be in synchronous rectification mode when voltage at the SEQ pin is applied. This will result in sinking current in the module if pre-bias voltage is present at the output of the module. When pre-bias immunity during start-up is required, the EZTM SEQUENCE feature must be disabled. not be equal. To allow for such variation and avoid the likelihood of a converter shutting off due to a current overload, the total capacity of the paralleled system should be no more than 75% of the sum of the individual converters. As an example, for a system of four ATS030A0X3-SR converters the parallel, the total current drawn should be less that 75% of (4 x 30A) , i.e. less than 90A. * All modules should be turned on and off together. This is so that all modules come up at the same time avoiding the problem of one converter sourcing current into the other leading to an overcurrent trip condition. To ensure that all modules come up simultaneously, the on/off pins of all paralleled converters should be tied together and the converters enabled and disabled using the on/off pin. * The share bus is not designed for redundant operation and the system will be non-functional upon failure of one of the unit when multiple units are in parallel. In particular, if one of the converters shuts down during operation, the other converters may also shut down due to their outputs hitting current limit. In such a situation, unless a coordinated restart is ensured, the system may never properly restart since different converters will try to restart at different times causing an overload condition and subsequent shutdown. This situation can be avoided by having an external output voltage monitor circuit that detects a shutdown condition and forces all converters to shut down and restart together. Active Load Sharing (-P Option) For additional power requirements, the Austin MegaLynx series power module is also available with a parallel option. Up to five modules can be configured, in parallel, with active load sharing. Good layout techniques should be observed when using multiple units in parallel. To implement forced load sharing, the following connections should be made: * The share pins of all units in parallel must be connected together. The path of these connections should be as direct as possible. * All remote-sense pins should be connected to the power bus at the same point, i.e., connect all the SENSE(+) pins to the (+) side of the bus. Close proximity and directness are necessary for good noise immunity Some special considerations apply for design of converters in parallel operation: * When sizing the number of modules required for parallel operation, take note of the fact that current sharing has some tolerance. In addition, under transient condtions such as a dynamic load change and during startup, all converter output currents will LINEAGE POWER 15 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 47. Note that the airflow is parallel to the long axis of the module as shown in Figure 48. The derating data applies to airflow in either direction of the module's long axis. 25.4_ (1.0) Wind Tunnel PWBs Power Module Back View Figure 48. Tref Temperature measurement location. The thermal reference point, Tref used in the specifications is shown in Figure 48. For reliable operation this temperature should not exceed 125oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note "Thermal Characterization Process For Open-Frame BoardMounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. 76.2_ (3.0) x 12.7_ (0.50) Probe Location for measuring airflow and ambient temperature Air flow Figure 47. Thermal Test Set-up. LINEAGE POWER 16 Data Sheet April 19, 2011 Austin MegaLynxTM Non-Isolated dc-dc Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Mechanical Outline of Module Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in) BACK SIDE VIEW Pin out Pin Function 1 Vo 2 Vo 3 Sense+ 4 Vo 5 GND 6 GND* 7 Share** 8 GND 9 VIN 10 VIN 11 SEQ 12 Trim 13 On/Off Pin 6 is added in ATH030A0X3 version ** Pin 7 is paralleling option LINEAGE POWER 17 Data Sheet April 19, 2011 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in) LINEAGE POWER 18 Data Sheet April 19, 2011 Austin MegaLynxTM Non-Isolated dc-dc Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Through-Hole Lead-Free Soldering Information The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power technical representative for more details. LINEAGE POWER 19 Austin MegaLynxTM: Non-Isolated DC-DC Power Modules: 4.5 - 5.5Vdc input; 0.8 - 3.63Vdc output; 30A output current 6.0 - 14Vdc input; 0.8 - 5.5Vdc output; 25A output current Data Sheet April 19, 2011 Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 2. Device Codes 0.8 - 3.63Vdc Output Current 25A On/Off Logic Negative Connector Type SIP 4.5 - 5.5Vdc 0.8 - 3.63Vdc 25A Negative 4.5 - 5.5Vdc 0.8 - 3.63Vdc 30A Negative 4.5 - 5.5Vdc 0.8 - 3.63Vdc 30A Negative Input Voltage Output Voltage 4.5 - 5.5Vdc Product codes Comcodes ATH025A0X3 108991980 SIP ATH025A0X3Z CC109104774 SIP ATH030A0X3 108992005 SIP ATH030A0X3Z CC109104782 4.5 - 5.5Vdc 0.8 - 3.63Vdc 30A Negative SIP ATH030A0X3-P 108993358 4.5 - 5.5Vdc 0.8 - 3.63Vdc 30A Negative SIP ATH030A0X3-PZ CC109104790 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X3 108991997 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X3Z CC109104808 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X53 108997210 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X3-P 108993341 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X3-PZ CC109104816 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X53-PZ CC109107752 6.0 - 14Vdc 0.8- 5.5Vdc 25A Negative SIP ATS025A0X3-34Z* CC109147897 * Special part, consult factory before ordering Table 3. Device Options Option Device Code Suffix Long pins 5.08mm 0.25m (0.2 in. 0.010 in.) -5 Paralleling with active current sharing -P RoHS Compliant -Z Asia-Pacific Headquarters Tel: +86.021.54279977*808 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-888-LINEAGE(546-3243) (Outside U.S.A.: +1-972-244-WATT(9288)) www.lineagepower.com e-mail: techsupport1@lineagepower.com Europe, Middle-East and Africa Headquarters Tel: +49.89.878067-280 India Headquarters Tel: +91.80.28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. (c) 2011 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved. LINEAGE POWER 20 Document No: DS05-012 ver. 1.06 PDF Name: austin_megalynx_sip.pdf