LM4755 LM4755 Stereo 11W Audio Power Amplifier with Mute Literature Number: SNAS010D LM4755 Stereo 11W Audio Power Amplifier with Mute PO at 10% THD+N @ 1kHz into 8 bridged TO-263 General Description The LM4755 is a stereo audio amplifier capable of delivering 11W per channel of continuous average output power to a 4 load or 7W per channel into 8 using a single 24V supply at 10% THD+N. The internal mute circuit and pre-set gain resistors provide for a very economical design solution. Output power specifications at both 20V and 24V supplies and low external component count offer high value to consumer electronic manufacturers for stereo TV and compact stereo applications. The LM4755 is specifically designed for single supply operation. Key Specifications Output power at 10% THD with 1kHz into 4 at VCC = 24V: 11W (typ) Output power at 10% THD with 1kHz into 8 at VCC = 24V: 7W (typ) Closed loop gain: 34dB (typ) PO at 10% THD+N @ 1kHz into 4 single-ended TO-263 package at VCC=12V: 2.5W (typ) package at VCC=12V: 5W (typ) Features Drives 4 and 8 loads Integrated mute function Internal Gain Resistors Minimal external components needed Single supply operation Internal current limiting and thermal protection Compact 9-lead TO-220 package Wide supply range 9V - 40V Applications Stereos TVs Compact stereos Mini component stereos Typical Application 10005901 FIGURE 1. Typical Audio Amplifier Application Circuit (c) 2008 National Semiconductor Corporation 100059 www.national.com LM4755 Stereo 11W Audio Power Amplifier with Mute May 14, 2008 LM4755 Connection Diagrams Plastic Package 10005902 Package Description Top View Order Number LM4755T Package Number TA09A 10005936 Top View Order Number LM4755TS Package Number TS9A www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Input Voltage Input Voltage at Output Pins (Note 8) Output Current Power Dissipation (Note 3) ESD Susceptibility (Note 4) Junction Temperature 250C -40C to 150C Operating Ratings 40V 0.7V GND -0.4V Internally Limited 62.5W 2 kV 150C Temperature Range TMIN TA TMAX Supply Voltage -40C TA +85C 9V to 32V JC 2C/W JA 76C/W Electrical Characteristics The following specifications apply to each channel with VCC = 24V, TA = 25C unless otherwise specified. LM4755 Symbol Typical (Note 5) Limit Units (Limits) Mute Off 10 15 7 mA(max) mA(min) Mute On 7 mA f = 1 kHz, THD+N = 10%, RL = 8 7 W f = 1 kHz, THD+N = 10%, RL = 4 11 VS = 20V, RL = 8 4 W VS = 20V, RL = 4 Parameter ITOTAL Total Quiescent Power Supply Current PO Output Power (Continuous Average per Channel) Conditions 10 W(min) 7 W f = 1 kHz, THD+N = 10%, RL = 4 VS = 12V, TO-263 Pkg. 2.5 W 0.08 % THD Total Harmonic Distortion f = 1 kHz, PO = 1 W/ch, RL = 8 VOSW Output Swing PO = 10W, RL = 8 15 V PO = 10W, RL = 4 14 V XTALK Channel Separation See Apps. Circuit f = 1 kHz, VO = 4 Vrms 55 dB PSRR Power Supply Rejection Ratio See Apps. Circuit f = 120 Hz, VO = 1 mVrms 50 dB VODV Differential DC Output Offset Voltage VIN = 0V SR Slew Rate RIN Input Impedance 83 k PBW Power Bandwidth 3 dB BW at PO = 2.5W, RL = 8 65 kHz AVCL Closed Loop Gain (Internally Set) RL = 8 34 0.09 0.4 2 IN Noise IHF-A Weighting Filter, RL = 8 Output Referred IO Output Short Circuit Limit VIN = 0.5V, RL = 2 Mute Pin VIL Mute Low Input Voltage Not in Mute Mode VIH Mute High Input Voltage In Mute Mode 2.0 AM Mute Attenuation VMUTE = 5.0V 80 3 V(max) V/s 33 dB(min) 35 dB(max) 0.2 mVrms 2 A(min) 0.8 V(max) 2.5 V(min) dB www.national.com LM4755 Soldering Information T Package (10 seconds) Storage Temperature Absolute Maximum Ratings (Note 2) LM4755 Note 1: All voltages are measured with respect to the GND pin (5), unless otherwse specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: For operating at case temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance of JC = 2C/W (junction to case). Refer to the section Determining the Maximum Power Dissipation in the Application Information section for more information. Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Note 5: Typicals are measured at 25C and represent the parametric norm. Note 6: Limits are guaranteed that all parts are tested in production to meet the stated values. Note 7: The TO-263 Package is not recommended for VS > 16V due to impractical heatsinking limitations. Note 8: The outputs of the LM4755 cannot be driven externally in any mode with a voltage lower than -0.4V below GND or permanent damage to the LM4755 will result. www.national.com 4 LM4755 10005903 Equivalent Schematic 5 www.national.com LM4755 Test Circuit 10005904 FIGURE 2. Test Circuit www.national.com 6 LM4755 System Application Circuit 10005905 FIGURE 3. Circuit for External Components Description External Components Description Components Function Description 1, 2 CS Provides power supply filtering and bypassing. 3, 4 RSN Works with CSN to stabilize the output stage from high frequency oscillations. 5, 6 CSN Works with RSN to stabilize the output stage from high frequency oscillations. 7 Cb Provides filtering for the internally generated half-supply bias generator. 8, 9 Ci Input AC coupling capacitor which blocks DC voltage at the amplifier's input terminals. Also creates a high pass 10, 11 Co 12, 13 Ri filter with fc=1/(2 * * Rout * Cout). Voltage control - limits the voltage level allowed to the amplifier's input terminals. 14 Rm Works with Cm to provide mute function timing. 15 Cm Works with Rm to provide mute function timing. filter with fc=1/(2 * * Rin * Cin). Output AC coupling capacitor which blocks DC voltage at the amplifier's output terminal. Creates a high pass 7 www.national.com LM4755 Typical Performance Characteristics (Note 5) THD+N vs Output Power THD+N vs Output Power 10005912 10005913 THD+N vs Output Power THD+N vs Output Power 10005914 10005906 THD+N vs Output Power THD+N vs Output Power 10005907 www.national.com 10005908 8 LM4755 THD+N vs Output Power THD+N vs Output Power 10005915 10005916 THD+N vs Output Power THD+N vs Output Power 10005917 10005909 THD+N vs Output Power THD+N vs Output Power 10005910 10005911 9 www.national.com LM4755 THD+N vs Output Power THD+N vs Output Power 10005938 10005939 THD+N vs Output Power THD+N vs Output Power 10005940 10005941 THD+N vs Output Power THD+N vs Output Power 10005942 www.national.com 10005943 10 LM4755 THD+N vs Output Power THD+N vs Output Power 10005944 10005945 THD+N vs Output Power THD+N vs Output Power 10005946 10005947 THD+N vs Output Power THD+N vs Output Power 10005948 10005949 11 www.national.com LM4755 Output Power vs Supply Voltage Output Power vs Supply Voltage 10005918 10005919 Frequency Response THD+N vs Frequency 10005921 10005920 THD+N vs Frequency Frequency Response 10005923 10005922 www.national.com 12 LM4755 Channel Separation PSRR vs Frequency 10005924 10005925 Supply Current vs Supply Voltage Power Derating Curve 10005926 10005927 Power Dissipation vs Output Power Power Dissipation vs Output Power 10005928 10005929 13 www.national.com LM4755 Power Dissipation vs Output Power Power Dissipation vs Output Power 10005960 10005961 the inputs (pins 3, 7) and outputs (pins 1, 8). As mentioned earlier in the External Components section these capacitors create high-pass filters with their corresponding input/output impedances. The Typical Application Circuit shown in Figure 1 shows input and output capacitors of 0.1 F and 1,000 F respectively. At the input, with an 83 k typical input resistance, the result is a high pass 3 dB point occurring at 19 Hz. There is another high pass filter at 39.8 Hz created with the output load resistance of 4. Careful selection of these components is necessary to ensure that the desired frequency response is obtained. The Frequency Response curves in the Typical Performance Characteristics section show how different output coupling capacitors affect the low frequency roll-off. Application Information The LM4755 contains circuitry to pull down the bias line internally, effectively shutting down the input stage. An external R-C should be used to adjust the timing of the pull-down. If the bias line is pulled down too quickly, currents induced in the internal bias resistors will cause a momentary DC voltage to appear across the inputs of each amplifier's internal differential pair, resulting in an output DC shift towards Vsupply. An R-C timing circuit should be used to limit the pull-down time such that output "pops" and signal feedthroughs will be minimized. The pull-down timing is a function of a number of factors, including the internal mute circuitry, the voltage used to activate the mute, the bias capacitor, the half-supply voltage, and internal resistances used in the half-supply generator. Table 1 shows a list of recommended values for the external R-C. OPERATING IN BRIDGE-MODE Though designed for use as a single-ended amplifier, the LM4755 can be used to drive a load differentially (bridgemode). Due to the low pin count of the package, only the noninverting inputs are available. An inverted signal must be provided to one of the inputs. This can easily be done with the use of an inexpensive op-amp configured as a standard inverting amplifier. An LF353 is a good low-cost choice. Care must be taken, however, for a bridge-mode amplifier must theoretically dissipate four times the power of a single-ended type. The load seen by each amplifier is effectively half that of the actual load being used, thus an amplifier designed to drive a 4 load in single-ended mode should drive an 8 load when operating in bridge-mode. TABLE 1. Recommended Values for Mute Circuit VMUTE VCC Rm Cm 5V 12V 18 k 10 F 5V 15V 18 k 10 F 5V 20V 12 k 10 F 5V 24V 12 k 10 F 5V 28V 8.2 k 10 F 5V 30V 8.2 k 10 F CAPACITOR SELECTION AND FREQUENCY RESPONSE With the LM4755, as in all single supply amplifiers, AC coupling capacitors are used to isolate the DC voltage present at www.national.com 14 LM4755 10005930 FIGURE 4. Bridge-Mode Application 10005931 10005937 FIGURE 5. THD+N vs POUT for Bridge-Mode Application 15 www.national.com LM4755 PREVENTING OSCILLATIONS With the integration of the feedback and bias resistors onchip, the LM4755 fits into a very compact package. However, due to the close proximity of the non-inverting input pins to the corresponding output pins, the inputs should be AC terminated at all times. If the inputs are left floating, the amplifier will have a positive feedback path through high impedance coupling, resulting in a high frequency oscillation. In most applications, this termination is typically provided by the previous stage's source impedance. If the application will require an external signal, the inputs should be terminated to ground with a resistance of 50 k or less on the AC side of the input coupling capacitors. UNDERVOLTAGE SHUTDOWN If the power supply voltage drops below the minimum operating supply voltage, the internal under-voltage detection circuitry pulls down the half-supply bias line, shutting down the preamp section of the LM4755. Due to the wide operating supply range of the LM4755, the threshold is set to just under 9V. There may be certain applications where a higher threshold voltage is desired. One example is a design requiring a high operating supply voltage, with large supply and bias capacitors, and there is little or no other circuitry connected to the main power supply rail. In this circuit, when the power is disconnected, the supply and bias capacitors will discharge at a slower rate, possibly resulting in audible output distortion as the decaying voltage begins to clip the output signal. An external circuit may be used to sense for the desired threshold, and pull the bias line (pin 6) to ground to disable the input preamp. Figure 6 shows an example of such a circuit. When the voltage across the zener diode drops below its threshold, current flow into the base of Q1 is interrupted. Q2 then turns on, discharging the bias capacitor. This discharge rate is governed by several factors, including the bias capacitor value, the bias voltage, and the resistor at the emitter of Q2. An equation for approximating the value of the emitter discharge resistor, R, is given below: 10005932 FIGURE 6. External Undervoltage Pull-Down THERMAL CONSIDERATIONS Heat Sinking Proper heatsinking is necessary to ensure that the amplifier will function correctly under all operating conditions. A heatsink that is too small will cause the die to heat excessively and will result in a degraded output signal as the thermal protection circuitry begins to operate. The choice of a heatsink for a given application is dictated by several factors: the maximum power the IC needs to dissipate, the worst-case ambient temperature of the circuit, the junction-to-case thermal resistance, and the maximum junction temperature of the IC. The heat flow approximation equation used in determining the correct heatsink maximum thermal resistance is given below: TJ-TA = PDMAX * (JC + CS + SA) where: PDMAX = maximum power dissipation of the IC TJ(C) = junction temperature of the IC TA(C) = ambient temperature R = (0.7v) / (Cb * (VCC/2) / 0.1s) Note that this is only a linearized approximation based on a discharge time of 0.1s. The circuit should be evaluated and adjusted for each application. As mentioned earlier in the Built-in Mute Circuit section, when using an external circuit to pull down the bias line, the rate of discharge will have an effect on the turn-off induced distortions. Please refer to the Built-in Mute Circuit section for more information. JC(C/W) = junction-to-case thermal resistance of the IC CS(C/W) = case-to-heatsink thermal resistance (typically 0.2 to 0.5 C/W) SA(C/W) = thermal resistance of heatsink When determining the proper heatsink, the above equation should be re-written as: SA [(TJ-TA) / PDMAX] - JC-CS TO-263 HEATSINKING Surface mount applications will be limited by the thermal dissipation properties of printed circuit board area. The TO-263 package is not recommended for surface mount applications with VS > 16V due to limited printed circuit board area. There are TO-263 package enhancements, such as clip-on heatsinks and heatsinks with adhesives, that can be used to improve performance. Standard FR-4 single-sided copper clad will have an approximate Thermal resistance (SA) ranging from: 1.5 x 1.5 in. sq. 2 x 2 in. sq. www.national.com 16 20-27C/W 16-23C/W (TA=28C, Sine wave testing, 1 oz. Copper) Calculating PDMAX: PDMAX = VCC2/(2RL) = (12V)2/2(4)) = 3.65W Calculating Heatsink Thermal Resistance: SA < TJ - TA / PDMAX - JC - CS SA < 120C/3.7W - 2.0C/W - 0.2C/W = 30.2C/W Therefore the recommendation is to use 1.5 x 1.5 square inch of single-sided copper clad. Example 2: (Stereo Single-Ended Output) Given: TA=50C TJ=150C RL=4 VS=12V DETERMINING MAXIMUM POWER DISSIPATION For a single-ended class AB power amplifier, the theoretical maximum power dissipation point is a function of the supply voltage, VS, and the load resistance, RL and is given by the following equation: (single channel) PDMAX (W) = [VS2 / (2 * 2 * RL)] The above equation is for a single channel class-AB power amplifier. For dual amplifiers such as the LM4755, the equation for calculating the total maximum power dissipated is: (dual channel) PDMAX (W) = 2 * [VS2 / (2 * 2 * RL)] or VS2 / (2 * RL) (Bridged Outputs) PDMAX (W) = 4[VS2 / (22 * RL)] JC=2C/W PDMAX from PD vs PO Graph: PDMAX 3.7W Calculating PDMAX: PDMAX = VCC2/(2RL)= (12V) 2/(2(4)) = 3.65W Calculating Heatsink Thermal Resistance: SA < [(TJ - TA) / PDMAX] - JC - CS SA < 100C/3.7W - 2.0C/W - 0.2C/W = 24.8C/W Therefore the recommendation is to use 2.0 x 2.0 square inch of single-sided copper clad. Example 3: (Bridged Output) Given: TA=50C TJ=150C RL=8 VS=12V HEATSINK DESIGN EXAMPLE Determine the system parameters: VS = 24V Operating Supply Voltage RL = 4 Minimum Load Impedance TA = 55C Worst Case Ambient Temperature JC=2C/W Device parameters from the datasheet: TJ = 150C Maximum Junction Temperature JC = 2C/W Junction-to-Case Thermal Resistance Calculating PDMAX: PDMAX = 4[VCC2/(22RL)] = 4(12V)2/(22(8)) = 3.65W Calculating Heatsink Thermal Resistance: Calculations: 2 * PDMAX = 2 * [VS2 / 2 * 2 * RL)] = (24V)2 / (2 * 2 * 4) = 14.6W SA < [(TJ - TA) / PDMAX] - JC - CS SA < 100C / 3.7W - 2.0C/W - 0.2C/W = 24.8C/W SA [(TJ-TA) / PDMAX] - JC-CS = [ (150C - 55C) / 14.6W] - 2C/W-0.2C/W = 4.3C/W Conclusion: Choose a heatsink with SA 4.3C/W. Therefore the recommendation is to use 2.0 x 2.0 square inch of single-sided copper clad. LAYOUT AND GROUND RETURNS Proper PC board layout is essential for good circuit performance. When laying out a PC board for an audio power amplifier, particular attention must be paid to the routing of the output signal ground returns relative to the input signal and bias capacitor grounds. To prevent any ground loops, the ground returns for the output signals should be routed separately and brought together at the supply ground. The input signal grounds and the bias capacitor ground line should also be routed separately. The 0.1 F high frequency supply bypass capacitor should be placed as close as possible to the IC. TO-263 HEATSINK DESIGN EXAMPLES Example 1: (Stereo Single-Ended Output) Given: TA=30C TJ=150C RL=4 VS=12V JC=2C/W PDMAX from PD vs PO Graph: PDMAX 3.7W 17 www.national.com LM4755 The above values for SA vary widely due to dimensional proportions (i.e. variations in width and length will vary SA). For audio applications, where peak power levels are short in duration, this part will perform satisfactory with less heatsinking/copper clad area. As with any high power design proper bench testing should be undertaken to assure the design can dissipate the required power. Proper bench testing requires attention to worst case ambient temperature and air flow. At high power dissipation levels the part will show a tendency to increase saturation voltages, thus limiting the undistorted power levels. LM4755 PC BOARD LAYOUT-COMPOSITE 10005933 www.national.com 18 LM4755 PC BOARD LAYOUT-SILK SCREEN 10005934 19 www.national.com LM4755 PC BOARD LAYOUT-SOLDER SIDE 10005935 www.national.com 20 LM4755 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM4755T NS Package Number TA9A 21 www.national.com LM4755 Order Number LM4755TS NS Package Number TS9A www.national.com 22 LM4755 Notes 23 www.national.com LM4755 Stereo 11W Audio Power Amplifier with Mute Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated