LM4890 LM4890 1 Watt Audio Power Amplifier Literature Number: SNAS138K LM4890 1 Watt Audio Power Amplifier General Description Key Specifications The LM4890 is an audio power amplifier primarily designed for demanding applications in mobile phones and other portable communication device applications. It is capable of delivering 1 watt of continuous average power to an 8 BTL load with less than 1% distortion (THD+N) from a 5VDC power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4890 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement. The LM4890 features a low-power consumption shutdown mode, which is achieved by driving the shutdown pin with logic low. Additionally, the LM4890 features an internal thermal shutdown protection mechanism. The LM4890 contains advanced pop & click circuitry which eliminates noises which would otherwise occur during turn-on and turn-off transitions. The LM4890 is unity-gain stable and can be configured by external gain-setting resistors. j PSRR at 217Hz, VDD = 5V (Fig. 1) 62dB(typ.) j Power Output at 5.0V & 1% THD 1W(typ.) j Power Output at 3.3V & 1% THD 400mW(typ.) j Shutdown Current 0.1A(typ.) Features n Available in space-saving packages: micro SMD, MSOP, SOIC, and LLP n Ultra low current shutdown mode n BTL output can drive capacitive loads n Improved pop & click circuitry eliminates noises during turn-on and turn-off transitions n 2.2 - 5.5V operation n No output coupling capacitors, snubber networks or bootstrap capacitors required n Thermal shutdown protection n Unity-gain stable n External gain configuration capability Applications n Mobile Phones n PDAs n Portable electronic devices Connection Diagrams 8 Bump micro SMD 8 bump micro SMD Marking 20019270 20019223 Top View Order Number LM4890IBP, LM4890IBPX See NS Package Number BPA08DDB Top View X - Date Code T - Die Traceability G - Boomer Family E - LM4890IBP Boomer (R) is a registered trademark of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS200192 www.national.com LM4890 1 Watt Audio Power Amplifier July 2006 LM4890 Connection Diagrams (Continued) 9 Bump micro SMD 9 Bump micro SMD Marking 200192C2 Top View X - Date Code T - Die Traceability G - Boomer Family P - LM4890IBL 200192C1 Top View Order Number LM4890IBL, LM4890IBLX See NS Package Number BLA09AAB LLP Package 10 Pin LLP Marking 200192C6 Top View Order Number LM4890LD See NS Package Number LDA10B Top View Z - Assembly Plant Date Code (M for Malacca) XY - Digit Date Code TT - Die Traceability L4890 - LM4890LD Mini Small Outline (MSOP) Package MSOP Marking 200192C7 20019271 Top View G - Boomer Family 90 - LM4890MM 20019236 Top View Order Number LM4890MM See NS Package Number MUA08A Small Outline (SO) Package SO Marking 20019272 Top View XY - Date Code TT - Die Traceability Bottom 2 lines - Part Number 20019235 Top View Order Number LM4890M See NS Package Number M08A www.national.com 2 LM4890 Connection Diagrams (Continued) 9 Bump micro SMD 9 Bump micro SMD Marking 200192D0 Top View X - Date Code T - Die Traceability G - Boomer Family A8 - LM4890ITL 200192C1 Top View Order Number LM4890ITL, LM4890ITLX See NS Package Number TLA09AAA Typical Application 20019201 FIGURE 1. Typical Audio Amplifier Application Circuit 3 www.national.com LM4890 Absolute Maximum Ratings (Note 2) JA (9 Bump micro SMD, Note 12) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. JC (MSOP) 56C/W JA (MSOP) 190C/W JA (LLP) 220C/W Supply Voltage (Note 11) 6.0V Storage Temperature Soldering Information -65C to +150C See AN-1112 "microSMD Wafers Level Chip Scale Package." -0.3V to VDD +0.3V Input Voltage Power Dissipation (Note 3) Internally Limited ESD Susceptibility (Note 4) 2000V Junction Temperature 150C 180C/W See AN-1187 "Leadless Leadframe Package (LLP)." Operating Ratings Thermal Resistance JC (SOP) 35C/W JA (SOP) 150C/W JA (8 Bump micro SMD, Note 12) 220C/W Temperature Range TMIN TA TMAX -40C TA 85C 2.2V VDD 5.5V Supply Voltage Electrical Characteristics VDD = 5V (Notes 1, 2, 8) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. LM4890 Symbol IDD Parameter Quiescent Power Supply Current Conditions Typical Limit (Note 6) (Notes 7, 9) Units (Limits) VIN = 0V, Io = 0A, No Load 4 8 mA (max) VIN = 0V, Io = 0A, 8 Load 5 10 mA (max) 0.1 2.0 A (max) ISD Shutdown Current VSDIH Shutdown Voltage Input High 1.2 V (min) VSDIL Shutdown Voltage Input Low 0.4 V (max) VOS Output Offset Voltage 50 mV (max) 9.7 k (max) 7.0 k (min) VSHUTDOWN = 0V 7 ROUT-GND Resistor Output to GND (Note 10) Po Output Power (8) TWU Wake-up time TSD Thermal Shutdown Temperature 8.5 THD = 2% (max); f = 1 kHz 1.0 0.8 W 170 220 ms (max) 170 THD+N Total Harmonic Distortion + Noise Po = 0.4 Wrms; f = 1kHz PSRR Power Supply Rejection Ratio (Note 14) Vripple = 200mV sine p-p Input Terminated with 10 ohms to ground TSDT Shut Down Time 8 load 150 C (min) 190 C (max) 0.1 % 62 (f = 217Hz) 66 (f = 1kHz) 55 1.0 dB (min) ms (max) Electrical Characteristics VDD = 3V (Notes 1, 2, 8) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. LM4890 Symbol Parameter Conditions Typical Limit Units (Limits) (Note 6) (Notes 7, 9) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A, No Load 3.5 7 mA (max) VIN = 0V, Io = 0A, 8 Load 4.5 9 mA (max) ISD Shutdown Current VSHUTDOWN = 0V 0.1 2.0 A (max) VSDIH Shutdown Voltage Input High 1.2 V(min) VSDIL Shutdown Voltage Input Low 0.4 V(max) VOS Output Offset Voltage 7 ROUT-GND Resistor Output to Gnd (Note 10) TWU 8.5 Wake-up time www.national.com 120 4 50 mV (max) 9.7 k (max) 7.0 k (min) 180 ms (max) LM4890 Electrical Characteristics VDD = 3V (Notes 1, 2, 8) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. (Continued) LM4890 Symbol Parameter Po Output Power (8) TSD Thermal Shutdown Temperature Conditions THD = 1% (max); f = 1kHz Limit (Note 6) (Notes 7, 9) 0.31 0.28 W 150 C(min) 190 C(max) 45 dB(min) 170 THD+N Total Harmonic Distortion + Noise Po = 0.15Wrms; f = 1kHz PSRR Power Supply Rejection Ratio (Note 14) Vripple = 200mV sine p-p Input terminated with 10 ohms to ground Units (Limits) Typical 0.1 % 56 (f = 217Hz) 62 (f = 1kHz) Electrical Characteristics VDD = 2.6V (Notes 1, 2, 8) The following specifications apply for for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. LM4890 Symbol Parameter Conditions Typical Limit (Note 6) (Notes 7, 9) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A, No Load 2.6 mA (max) ISD Shutdown Current VSHUTDOWN = 0V 0.1 A (max) P0 Output Power (8) Output Power (4) THD = 1% (max); f = 1 kHz THD = 1% (max); f = 1 kHz 0.2 0.22 W W THD+N Total Harmonic Distortion + Noise Po = 0.1Wrms; f = 1kHz 0.08 % PSRR Power Supply Rejection Ratio (Note 14) Vripple = 200mV sine p-p Input Terminated with 10 ohms to ground 44 (f = 217Hz) 44 (f = 1kHz) dB Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4890, see power derating curves for additional information. Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Note 5: Machine Model, 220 pF-240 pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. Note 9: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 10: ROUT is measured from each of the output pins to ground. This value represents the parallel combination of the 10k ohm output resistors and the two 20k ohm resistors. Note 11: If the product is in shutdown mode and VDD exceeds 6V (to a max of 8V VDD), then most of the excess current will flow through the ESD protection circuits. If the source impedance limits the current to a max of 10 ma, then the part will be protected. If the part is enabled when VDD is greater than 5.5V and less than 6.5V, no damage will occur, although operational life will be reduced. Operation above 6.5V with no current limit will result in permanent damage. Note 12: All bumps have the same thermal resistance and contribute equally when used to lower thermal resistance. All bumps must be connected to achieve specified thermal resistance. Note 13: Maximum power dissipation (PDMAX) in the device occurs at an output power level significantly below full output power. PDMAX can be calculated using Equation 1 shown in the Application section. It may also be obtained from the power dissipation graphs. Note 14: PSRR is a function of system gain. Specifications apply to the circuit in Figure 1 where AV = 2. Higher system gains will reduce PSRR value by the amount of gain increase. A system gain of 10 represents a gain increase of 14dB. PSRR will be reduced by 14dB and applies to all operating voltages. 5 www.national.com LM4890 External Components Description Components (Figure 1) Functional Description 1. RIN Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high pass filter with CIN at fC= 1/(2 RINCIN). 2. CIN Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a highpass filter with RIN at fc = 1/(2 RINCIN). Refer to the section, Proper Selection of External Components, for an explanation of how to determine the value of CIN. 3. Rf Feedback resistance which sets the closed-loop gain in conjunction with RIN. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to the section, Power Supply Bypassing, for information concerning proper placement and selection of the supply bypass capacitor, CBYPASS. 5. CBYPASS Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External Components, for information concerning proper placement and selection of CBYPASS. www.national.com 6 THD+N vs Frequency at VDD = 3.3V, 8 RL, and PWR = 150mW, AV = 2 THD+N vs Frequency at VDD = 5V, 8 RL, and PWR = 250mW, AV = 2 20019237 20019238 THD+N vs Frequency at VDD = 3V, RL = 8, PWR = 250mW, AV = 2 20019290 THD+N vs Frequency THD+N vs Frequency @ VDD = 2.6V, RL = 8, PWR = 100mW, AV = 2 @ VDD = 2.6V, RL = 4, PWR = 100mW, AV = 2 20019239 20019240 7 www.national.com LM4890 Typical Performance Characteristics LM4890 Typical Performance Characteristics (Continued) THD+N vs Power Out THD+N vs Power Out @ VDD = 5V, RL = 8, 1kHz, AV = 2 @ VDD = 3.3V, RL = 8, 1kHz, AV = 2 200192C9 20019242 THD+N vs Power Out @ VDD = 3V, RL = 8, 1kHz, AV = 2 20019291 THD+N vs Power Out THD+N vs Power Out @ VDD = 2.6V, RL = 8, 1kHz, AV = 2 @ VDD = 2.6V, RL = 4, 1kHz, AV = 2 20019243 www.national.com 20019244 8 (Continued) Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 5V, Vripple = 200mvp-p RL = 8, RIN = 10 Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 5V, Vripple = 200mvp-p RL = 8, RIN = Float 20019245 20019273 Power Supply Rejection Ratio (PSRR) @ AV = 4 VDD = 5V, Vripple = 200mvp-p RL = 8, RIN = 10 Power Supply Rejection Ratio (PSRR) @ AV = 4 VDD = 5V, Vripple = 200mvp-p RL = 8, RIN = Float 200192A9 200192B8 9 www.national.com LM4890 Typical Performance Characteristics LM4890 Typical Performance Characteristics (Continued) Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 3V, Vripple = 200mvp-p, RL = 8, RIN = 10 Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 3V, Vripple = 200mvp-p, RL = 8, RIN = Float 20019293 200192C5 Power Supply Rejection Ratio (PSRR) @ AV = 4 VDD = 3V, Vripple = 200mvp-p, RL = 8, RIN = 10 Power Supply Rejection Ratio (PSRR) @ AV = 4 VDD = 3V, Vripple = 200mvp-p, RL = 8, RIN = Float 200192B1 200192B9 Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 3.3V, Vripple = 200mvp-p, RL = 8, RIN = 10 Power Supply Rejection Ratio (PSRR) @ AV = 2 VDD = 2.6V, Vripple = 200mvp-p, RL = 8, RIN = 10 20019246 www.national.com 20019247 10 LM4890 Typical Performance Characteristics (Continued) PSRR vs DC Output Voltage VDD = 5V, AV = 4 PSRR vs DC Output Voltage VDD = 5V, AV = 2 20019297 20019296 PSRR vs DC Output Voltage VDD = 3V, AV = 2 PSRR vs DC Output Voltage VDD = 5V, AV = 10 20019294 200192A3 PSRR vs DC Output Voltage VDD = 3V, AV = 10 PSRR vs DC Output Voltage VDD = 3V, AV = 4 20019295 200192A4 11 www.national.com LM4890 Typical Performance Characteristics (Continued) PSRR Distribution VDD = 5V 217Hz, 200mvp-p, -30, +25, and +80C PSRR Distribution VDD = 3V 217Hz, 200mvp-p, -30, +25, and +80C 200192B4 200192B5 VDD Power Supply Rejection Ration vs Bypass Capacitor Size = 5V, Input Grounded = 10, Output Load = 8 VDD Power Supply Rejection Ration vs Bypass Capacitor Size = 3V, Input Grounded = 10, Output Load = 8 200192A7 200192A8 Top Trace = No Cap, Next Trace Down = 1f Next Trace Down = 2f, Bottom Trace = 4.7f Top Trace = No Cap, Next Trace Down = 1f Next Trace Down = 2f, Bottom Trace = 4.7f LM4890 vs LM4877 Power Supply Rejection Ratio VDD = 5V, Input Grounded = 10 Output Load = 8, 200mV Ripple LM4890 vs LM4877 Power Supply Rejection Ratio VDD = 3V, Input Grounded = 10 Output Load = 8, 200mV Ripple 20019288 20019289 LM4890 = Bottom Trace LM4877 = Top Trace www.national.com LM4890 = Bottom Trace LM4877 = Top Trace 12 (Continued) Power Derating Curves (PDMAX = 670mW) Power Derating - 8 bump SMD (PDMAX = 670mW) 20019283 20019284 Ambient Temperature in Degrees C Note: (PDMAX = 670mW for 5V, 8) Ambient Temperature in Degrees C Note: (PDMAX = 670mW for 5V, 8) Power Derating - 9 bump SMD (PDMAX = 670mW) Power Derating - 10 Pin LD Pkg (PDMAX = 670mW) 20019285 200192C8 Ambient Temperature in Degrees C Note: (PDMAX = 670mW for 5V, 8) Ambient Temperature in Degrees C Note: (PDMAX = 670mW for 5V, 8) Power Output vs Supply Voltage Power Output vs Temperature 200192A1 200192A2 13 www.national.com LM4890 Typical Performance Characteristics LM4890 Typical Performance Characteristics (Continued) Power Dissipation vs Output Power VDD = 3.3V, 1kHz, 8, THD 1.0% Power Dissipation vs Output Power VDD = 5V, 1kHz, 8, THD 1.0% 20019248 20019249 Output Power vs Load Resistance Power Dissipation vs Output Power VDD = 2.6V, 1kHz 20019274 20019250 Supply Current vs Ambient Temperature Clipping (Dropout) Voltage vs Supply Voltage 20019299 www.national.com 20019252 14 LM4890 Typical Performance Characteristics (Continued) Max Die Temp at PDMAX (8 bump microSMD) Max Die Temp at PDMAX (9 bump microSMD) 20019286 20019287 Output Offset Voltage Supply Current vs Shutdown Voltage 200192B7 20019253 Shutdown Hysterisis Voltage VDD = 3V Shutdown Hysterisis Voltage VDD = 5V 20019279 20019280 15 www.national.com LM4890 Typical Performance Characteristics (Continued) Open Loop Frequency Response VDD = 3V, No Load Open Loop Frequency Response VDD = 5V, No Load 20019281 20019282 Gain / Phase Response, AV = 4 VDD = 5V, 8 Load, CLOAD = 500pF Gain / Phase Response, AV = 2 VDD = 5V, 8 Load, CLOAD = 500pF 200192B2 200192B3 Phase Margin vs CLOAD, AV = 4 VDD = 5V, 8 Load Capacitance to gnd on each output Phase Margin vs CLOAD, AV = 2 VDD = 5V, 8 Load Capacitance to gnd on each output 200192A6 200192A5 www.national.com 16 LM4890 Typical Performance Characteristics (Continued) Phase Margin and Limits vs Application Variables, RIN = 22K 20019298 Wake Up Time (TWU) 200192B6 Frequency Response vs Input Capacitor Size Noise Floor 20019254 20019256 17 www.national.com LM4890 POWER DISSIPATION Application Information Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or single-ended. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. Since the LM4890 has two operational amplifiers in one package, the maximum internal power dissipation is 4 times that of a single-ended amplifier. The maximum power dissipation for a given application can be derived from the power dissipation graphs or from Equation 1. (1) PDMAX = 4*(VDD)2/(22RL) It is critical that the maximum junction temperature TJMAX of 150C is not exceeded. TJMAX can be determined from the power derating curves by using PDMAX and the PC board foil area. By adding additional copper foil, the thermal resistance of the application can be reduced, resulting in higher PDMAX. Additional copper foil can be added to any of the leads connected to the LM4890. Refer to the APPLICATION INFORMATION on the LM4890 reference design board for an example of good heat sinking. If TJMAX still exceeds 150C, then additional changes must be made. These changes can include reduced supply voltage, higher load impedance, or reduced ambient temperature. Internal power dissipation is a function of output power. Refer to the Typical Performance Characteristics curves for power dissipation information for different output powers and output loading. BRIDGED CONFIGURATION EXPLANATION As shown in Figure 1, the LM4890 has two operational amplifiers internally, allowing for a few different amplifier configurations. The first amplifier's gain is externally configurable, while the second amplifier is internally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of Rf to RIN while the second amplifier's gain is fixed by the two internal 20k resistors. Figure 1 shows that the output of amplifier one serves as the input to amplifier two which results in both amplifiers producing signals identical in magnitude, but out of phase by 180. Consequently, the differential gain for the IC is AVD= 2 *(Rf/RIN) By driving the load differentially through outputs Vo1 and Vo2, an amplifier configuration commonly referred to as "bridged mode" is established. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of the load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's closed-loop gain without causing excessive clipping, please refer to the Audio Power Amplifier Design section. POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. Typical applications employ a 5V regulator with 10 F tantalum or electrolytic capacitor and a ceramic bypass capacitor which aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the LM4890. The selection of a bypass capacitor, especially CBYPASS, is dependent upon PSRR requirements, click and pop performance (as explained in the section, Proper Selection of External Components), system cost, and size constraints. A bridge configuration, such as the one used in the LM4890, also creates a second advantage over single-ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, single-ended amplifier configuration. Without an output coupling capacitor, the half-supply bias across the load would result in both increased internal IC power dissipation and also possible loudspeaker damage. EXPOSED-DAP PACKAGE PCB MOUNTING CONSIDERATIONS FOR THE LM4890LD The LM4890LD's exposed-DAP (die attach paddle) package (LD) provides a low thermal resistance between the die and the PCB to which the part is mounted and soldered. The LM4890LD package should have its DAP soldered to the grounded copper pad (heatsink) under the LM4890LD (the NC pins, no connect, and ground pins should also be directly connected to this copper pad-heatsink area). The area of the copper pad (heatsink) can be determined from the LD Power Derating graph. If the multiple layer copper heatsink areas are used, then these inner layer or backside copper heatsink areas should be connected to each other with 4 (2 x 2) vias. The diameter for these vias should be between 0.013 inches and 0.02 inches with a 0.050inch pitch-spacing. Ensure efficient thermal conductivity by plating through and solderfilling the vias. Further detailed information concerning PCB layout, fabrication, and mounting an LLP package is available from National Semiconductor's Package Engineering Group under application note AN1187. www.national.com SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4890 contains a shutdown pin to externally turn off the amplifier's bias circuitry. This shutdown feature turns the amplifier off when a logic low is placed on the shutdown pin. By switching the shutdown pin to ground, the LM4890 supply current draw will be minimized in idle mode. While the device will be disabled with shutdown pin voltages less than 0.5VDC, the idle current may be greater than the typical value of 0.1A. (Idle current is measured with the shutdown pin grounded). In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry to provide a quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-up resistor. When the switch is closed, the shutdown pin is connected to ground and disables the amplifier. If the switch is open, then the external pull-up resistor will enable the LM4890. This scheme guarantees that the shutdown pin will not float thus preventing unwanted state changes. 18 produce a virtually clickless and popless shutdown function. While the device will function properly, (no oscillations or motorboating), with CBYPASS equal to 0.1F, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CBYPASS equal to 1.0F is recommended in all but the most cost sensitive designs. (Continued) SHUTDOWN OUTPUT IMPEDANCE For Rf = 20k ohms: ZOUT1 (between Out1 and GND) = 10k||50k||Rf = 6k AUDIO POWER AMPLIFIER DESIGN ZOUT2 (between Out2 and GND) = 10k||(40k+(10k||Rf)) = 8.3k A 1W/8 Audio Amplifier Given: ZOUT1-2 (between Out1 and Out2) = 40k||(10k+(10k||Rf)) = 11.7k Power Output 1 Wrms Load Impedance 8 Input Level The -3dB roll off for these measurements is 600kHz 1 Vrms Input Impedance Bandwidth PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4890 is tolerant of external component combinations, consideration to component values must be used to maximize overall system quality. The LM4890 is unity-gain stable which gives the designer maximum system flexibility. The LM4890 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1Vrms are available from sources such as audio codecs. Please refer to the section, Audio Power Amplifier Design, for a more complete explanation of proper gain selection. Besides gain, one of the major considerations is the closedloop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, CIN, forms a first order high pass filter which limits low frequency response. This value should be chosen based on needed frequency response for a few distinct reasons. 20 k 100 Hz-20 kHz 0.25 dB A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section, the supply rail can be easily found. A second way to determine the minimum supply rail is to calculate the required Vopeak using Equation 2 and add the output voltage. Using this method, the minimum supply voltage would be (Vopeak + (VODTOP + VODBOT)), where VODBOT and VODTOP are extrapolated from the Dropout Voltage vs Supply Voltage curve in the Typical Performance Characteristics section. (2) 5V is a standard voltage which in most applications is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4890 to reproduce peaks in excess of 1W without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the Power Dissipation section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation 3. Selection Of Input Capacitor Size Large input capacitors are both expensive and space hungry for portable designs. Clearly, a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 100Hz to 150Hz. Thus, using a large input capacitor may not increase actual system performance. In addition to system cost and size, click and pop performance is effected by the size of the input coupling capacitor, CIN. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage (nominally 1/2 VDD). This charge comes from the output via the feedback and is apt to create pops upon device enable. Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on pops can be minimized. Besides minimizing the input capacitor size, careful consideration should be paid to the bypass capacitor value. Bypass capacitor, CBYPASS, is the most critical component to minimize turn-on pops since it determines how fast the LM4890 turns on. The slower the LM4890's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the smaller the turn-on pop. Choosing CBYPASS equal to 1.0F along with a small value of CIN, (in the range of 0.1F to 0.39F), should (3) Rf/RIN = AVD/2 From Equation 3, the minimum AVD is 2.83; use AVD = 3. Since the desired input impedance is 20 k, and with an AVD gain of 3, a ratio of 1.5:1 of Rf to RIN results in an allocation of RIN = 20 k and Rf = 30 k. The final design step is to address the bandwidth requirements which must be stated as a pair of -3 dB frequency points. Five times away from a -3 dB point is 0.17 dB down from passband response which is better than the required 0.25 dB specified. fL = 100Hz/5 = 20Hz fH = 20kHz * 5 = 100kHz 19 www.national.com LM4890 Application Information LM4890 Application Information With a AVD = 3 and fH = 100kHz, the resulting GBWP = 300kHz which is much smaller than the LM4890 GBWP of 2.5MHz. This calculation shows that if a designer has a need to design an amplifier with a higher differential gain, the LM4890 can still be used without running into bandwidth limitations. (Continued) As stated in the External Components section, RIN in conjunction with CIN create a highpass filter. CIN 1/(2*20 k*20Hz) = 0.397F; use 0.39F The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain, AVD. 20019224 FIGURE 2. HIGHER GAIN AUDIO AMPLIFIER The LM4890 is unity-gain stable and requires no external components besides gain-setting resistors, an input coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential gain of greater than 10 is required, a feedback capacitor (C4) may be needed as shown in Figure 2 to bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that elimi- www.national.com nates possible high frequency oscillations. Care should be taken when calculating the -3dB frequency in that an incorrect combination of R3 and C4 will cause rolloff before 20kHz. A typical combination of feedback resistor and capacitor that will not produce audio band high frequency rolloff is R3 = 20k and C4 = 25pf. These components result in a -3dB point of approximately 320 kHz. 20 LM4890 Application Information (Continued) 20019229 FIGURE 3. DIFFERENTIAL AMPLIFIER CONFIGURATION FOR LM4890 20019225 FIGURE 4. REFERENCE DESIGN BOARD and LAYOUT - micro SMD 21 www.national.com LM4890 Application Information (Continued) LM4890 micro SMD BOARD ARTWORK Silk Screen Top Layer 20019257 20019258 Bottom Layer Inner Layer VDD 20019259 20019260 Inner Layer Ground 20019261 www.national.com 22 LM4890 Application Information (Continued) 20019268 FIGURE 5. REFERENCE DESIGN BOARD and PCB LAYOUT GUIDELINES - MSOP & SO Boards 23 www.national.com LM4890 Application Information (Continued) LM4890 SO DEMO BOARD ARTWORK LM4890 MSOP DEMO BOARD ARTWORK Silk Screen Silk Screen 20019262 20019265 Top Layer Top Layer 20019263 20019266 Bottom Layer Bottom Layer 20019264 20019267 www.national.com 24 LM4890 Application Information (Continued) Mono LM4890 Reference Design Boards Bill of Material for all 3 Demo Boards Item Part Number 1 551011208-001 LM4890 Mono Reference Design Board Part Description 1 Qty 10 482911183-001 LM4890 Audio AMP 1 20 151911207-001 Tant Cap 1uF 16V 10 1 C1 21 151911207-002 Cer Cap 0.39uF 50V Z5U 20% 1210 1 C2 25 152911207-001 Tant Cap 1uF 16V 10 1 C3 30 472911207-001 Res 20K Ohm 1/10W 5 3 35 210007039-002 Jumper Header Vertical Mount 2X1 0.100 2 PCB LAYOUT GUIDELINES Ref Designator U1 R1, R2, R3 J1, J2 Single-Point Power / Ground Connections The analog power traces should be connected to the digital traces through a single point (link). A "Pi-filter" can be helpful in minimizing High Frequency noise coupling between the analog and digital sections. It is further recommended to put digital and analog power traces over the corresponding digital and analog ground traces to minimize noise coupling. This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power and ground traces. Designers should note that these are only "rule-of-thumb" recommendations and the actual results will depend heavily on the final layout. GENERAL MIXED SIGNAL LAYOUT RECOMMENDATIONS Placement of Digital and Analog Components All digital components and high-speed digital signals traces should be located as far away as possible from analog components and circuit traces. Power and Ground Circuits For 2 layer mixed signal design, it is important to isolate the digital power and ground trace paths from the analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even device. This technique will require a greater amount of design time but will not increase the final price of the board. The only extra parts required will be some jumpers. Avoiding Typical Design / Layout Problems Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90 degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise coupling and cross talk. 25 www.national.com LM4890 Physical Dimensions inches (millimeters) unless otherwise noted Note: Unless otherwise specified. 1. Epoxy coating. 2. 63Sn/37Pb eutectic bump. 3. Recommend non-solder mask defined landing pad. 4. Pin 1 is established by lower left corner with respect to text orientation pins are numbered counterclockwise. 5. Reference JEDEC registration MO-211, variation BC. 8-Bump micro SMD Order Number LM4890IBP, LM4890IBPX NS Package Number BPA08DDB X1 = 1.361 0.03 X2 = 1.361 0.03 X3 = 0.850 0.10 www.national.com 26 LM4890 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 9-Bump micro SMD Order Number LM4890IBL, LM4890IBLX NS Package Number BLA09AAB X1 = 1.514 0.03 X2 = 1.514 0.03 X3 = 0.945 0.10 MSOP Order Number LM4890MM NS Package Number MUA08A 27 www.national.com LM4890 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) SO Order Number LM4890M NS Package Number M08A www.national.com 28 LM4890 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) LLP Order Number LM4890LD NS Package Number LDA10B 9-Bump micro SMD Order Number LM4890ITL, LM4890ITLX NS Package Number TLA09AAA X1 = 1.514 0.03 X2 = 1.514 0.03 X3 = 0.600 0.075 29 www.national.com LM4890 1 Watt Audio Power Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated