1
®
FN6491.0
5962-0625601QHC, 5962-0625602QHC
1.4GHz Current Feedback Amplifiers with
Enable
The 5962-0625601QHC and 5962-0625602QHC are fully
DSCC SMD compliant parts and the SMD data sheets are
available on the DSCC website (http://www.dscc.dla.mil/
programs/specfind/default.asp). The 5962-0625601QHC is
electrically equivalent to the EL5166, the 5962-
0625602QHC is electrically equivalent to the EL5167.
Reference equivalent “EL” data sheet for addition al
information. The amplifiers are of the current feedback
variety and exhibit a very high bandwidth of 1.4GHz at AV =
+1 and 800MHz at AV = +2. This makes these amplifiers
ideal for today's high speed video and monitor applications,
as well as a number of RF and IF frequen cy designs.
With a supply current of just 12mA and the ability to run from
a single supply voltage from 5V to 12V, these amplifiers offer
very high performance for li ttle power consumption.
The 5962-0625601QHC also incorporates an enable and
disable function to reduce the supply current to 13µA typical
per amplifier. Allowing the CE pin to float or applying a low
logic level will enable the amplifier.
Features
• Gain-of-1 bandwidth = 1.4GHz/gain-of-2
bandwidth = 800MHz
• 6000V/µs slew rate
• Single and dual supply operation from 5V to 12V
• Low noise = 1.5nV/√Hz
• 12mA supply current
• Fast enable/disable (5962-0625601QHC only)
Applications
• Video amplifiers
• Cable drivers
• RGB amplifiers
• Test equipment
• Instrumentation
• Current to voltage converters
Ordering Information
PART NUMBER PART MARKING PACKAGE PKG.
DWG. #
5962-0625601QHC 06256 01QHC 10 Ld Flat Pack K10.A
5962-0625602QHC 06256 02QHC 10 Ld Flat Pack K10.A
Pinouts 5962-0625601QHC
(10 LD FLAT PACK)
TOP VIEW
5962-0625602QHC
(10 LD FLAT PACK)
TOP VIEW
IN+
VS-
CE
VS+
NC
10
9
8
7
6
2
3
4
5
1
IN-
NC
OUT
NC
NC
IN+
VS-
NC
VS+
NC
10
9
8
7
6
2
3
4
5
1
IN-
NC
OUT
NC
NC
Data Sheet May 2, 2007
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
2FN6491.0
May 2, 2007
Absolute Maximum Ratings (TA = +25°C) Thermal Information
Supply Voltage between VS+ and VS-. . . . . . . . . . . . . . . . . . . 12.6V
Slewrate between VS+ and VS-. . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 20mA
I into VIN+, VIN-, Enable Pins . . . . . . . . . . . . . . . . . . . . . . . . . ±4mA
Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V
Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W)
Flat Pack Package (Notes 1, 2) . . . . . . 165 60
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . .-55°C to +125°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144mW
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefo re: TJ = TC = TA
Electrical Specifications VS+ = +5V, VS- = -5V, RF = 392Ω for AV = 1, RF = 250Ω for AV = 2, RL = 150Ω, TA = +25°C
Unless Otherwise Specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
AC PERFORMANCE
BW -3dB Bandwidth AV = +1 1400 MHz
AV = +2 800 MHz
BW1 0.1dB Bandwidth AV = +2 100 MHz
SR Slew Rate VO = -2.5V to +2.5V, AV = +2 6000 V/µs
tS0.1% Settling Time VOUT = -2.5V to +2.5V, AV = -1 8 ns
eNInput Voltage Noise 1.7 nV/√Hz
iN- IN- Input Current Noise 19 pA/√Hz
iN+ IN+ Input Current Noise 50 pA/√Hz
dG Differential Gain Error (Note 3) AV = +2 0.01 %
dP Differential Phase Error (Note 3) AV = +2 0.03 °
INPUT CHARACTERISTICS
CIN Input Capacitance 1.5 pF
ENABLE (5962-0625601QHC ONLY)
tEN Enable Time 170 ns
tDIS Disable Time 1.25 µs
NOTE:
3. Standard NTSC test, AC signal amplitude = 286mV, f = 3.58MHz.
5962-0625601QHC, 5962-0625602QHC
3
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No lice nse is gran t ed by i mpli catio n or other wise u nder an y p a tent or patent rights of Intersi l or it s sub sidi ari es.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6491.0
May 2, 2007
Pin Descriptions
5962-0625601QHCIS
(10 LD FLAT PACK) 5962-0625601QHCIS
(10 LD FLAT PACK) PIN
NAME FUNCTION EQUIVALENT CIRCUIT
1, 5, 9, 10 1, 5, 8 , 9 ,10 NC Not connected
2 2 IN- Inverting input
CIRCUIT 1
3 3 IN+ Non-inverting input (See circuit 1)
4 4 VS- Negative supply
6 6 OUT Output
CIRCUIT 2
7 7 VS+ Positive supply
8CE
Chip enable
CIRCUIT 3
IN-IN+
V
S+
VS-
VS+
VS-
OUT
V
S+
VS-
CE
5962-0625601QHC, 5962-0625602QHC
4FN6491.0
May 2, 2007
5962-0625601QHC, 5962-0625602QHC
Ceramic Metal Seal Flatpack Packages (Flatpack)
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the lim-
its of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass
overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness. The maximum lim-
its of lead dimensions b and c or M shall be measured at the cen-
troid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric mate-
rials shall be molded to the bottom of the package to cover the
leads.
8. Dimension Q shall be measured at the point of exit (beyond the
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when sol-
der dip lead finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
-D-
-C-
0.004 H A - B
MD
S S
-A- -B-
0.036 H A - B
MD
S S
e
E
A
Q
L
A
E1
SEATING AND
LE2
E3 E3
BASE PLANE
-H-
b
C
S1
M
c1
b1
(c)
(b)
SECTION A-A
BASE
LEAD FINISH
METAL
PIN NO. 1
ID AREA
A
M
D
K10.A MIL-STD-1835 CDFP3-F10 (F-4A, CONFIGURATION B)
10 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A 0.045 0.115 1.14 2.92 -
b 0.015 0.022 0.38 0.56 -
b1 0.015 0.019 0.38 0.48 -
c 0.004 0.009 0.10 0.23 -
c1 0.004 0.006 0.10 0.15 -
D - 0.290 - 7.37 3
E 0.240 0.260 6.10 6.60 -
E1 -0.280-7.11 3
E2 0.125 - 3.18 - -
E3 0.030 - 0.76 - 7
e 0.050 BSC 1.27 BSC -
k 0.008 0.015 0.20 0.38 2
L 0.250 0.370 6.35 9.40 -
Q 0.026 0.045 0.66 1.14 8
S1 0.005 - 0.13 - 6
M - 0.0015 - 0.04 -
N10 10-
Rev. 0 3/07
