CPFE500F Series 500W Conduction Cooled Power Supplies Features Base plate cooled, no fan required High efficiency Protective coating option MIL STD 461/462D CE102 Conducted EMC Key Market Segments & Applications Specifications Model AC Input VAC/Hz Input Current Model dependant (1) A Inrush Current (115 / 230VAC) A Power Factor Efficiency (typical) % Output Voltage Setpoint Accuracy Total Regulation % Ripple and Noise (20MHz BW) Over Current Protection % Over Voltage Protection Series Operation Parallel Operation ORing Diodes/FETs Power On Signal (ENA) Auxiliary Supply Remote On/Off (Opto isolated) Temperature Coefficient Overtemperature C Hold Up Time (230VAC) ms Leakage Curr. (at 230VAC, 50Hz) mA Remote Sense Operating Temp. (Base plate) C Storage Temperature C Humidity Cooling Withstand Voltage Vibration (non operating) Shock Safety Agency Approvals Line Dip Conducted EMI Radiated EMI Immunity Weight (Typ) Size (L x W x D) Warranty g mm yrs 90 to 265VAC, 47-63Hz (up to 440Hz) (3) 6.8 / 3.4 20 / 40 peak Meets EN61000-3-2 85% at 75% loading (Non ORing diode versions) 2% at 50% load < 4%. (ORing diode option, adds 1V to load regulation) 1% (1.5% below -10C) 105 - 140% (Automatic Recovery) 125 - 145% (Cycle AC to reset) Yes Yes (Single wire, up to 6 units) Yes (option) Open collector (10mA sink current). Low (on) when output is present 10 - 14V, 20mA High = On <0.01%/C Shuts down between 90 - 130C (Cycle AC to reset) 10ms < 1.5mA Yes, compensates up to 500mV cable drop -40 to +85C (2) -40 to +100C Operating: 20 - 95%RH, Non operating 10 - 95%RH (Pcb assembly protective coated) Conduction cooled through 6mm base plate Input to Output 4242VDC, Input to Ground 2121VDC, Output to ground 500VDC MIL-STD-810E, Method 514.4, Proc 1, Category 1, 9 MIL-STD-810E, Method 516.5, Proc. I, IV, VI UL60950-1, CSA 22.2 No 60950-1, EN60950-1 (Ed 2), CE Mark Complies with SEMI F47 (200VAC line only) EN55011, EN55022 (as per CISPR, 11/22) Class B, FCC47 part 15 subpart B) MIL STD 461E/461E/462D CE102, 115V and 220V EN55011, EN55022 (as per CISPR, 11/22) Class B, FCC47 part 15 subpart B) see app. note for details IEC61000-4-2 (Contact Level 2, Air discharge Lvl 3), -3 (Lvl 3), -4(Lvl 3), -5 (Lvl 4), -6 (Lvl 3), -8 (Lvl 4), -11 (Class 3 ), -12 (Lvl 3), -14 (Class 3) with cover 1400g, without cover 1200g 270 x 126 x 55mm 2 years (1) 100/200VAC (2) CPFE500F-12: -40 to 80C. See instruction manuals for derating curves (3) Reduced PFC above 63Hz. Contact technical support for 440Hz operation. 1-800-526-2324 * www.us.tdk-lambda.com/lp/ 24 Disclaimer: us.tdk-lambda.com/lp/legal.htm CPFE500F Series Model Selector Model CPFE500F-12-NLC CPFE500F-24-NLC CPFE500F-28-NLC CPFE500F-48-NLC Options Output Volt (V) Adjust Range (V) Max Curr (A) Max Watt (W) 12 24 28 48 9.6 - 14.4 22.4 - 33.6 22.4 - 33.6 38.4 - 57.6 42 18 18 10.5 504 504 504 504 Part Number Desc. Suffix -DLC -NLC ORing Diode (3) Cover Protective Coating Y N Y Y Y Y 3) Reduces maximum output adjustment range by 1V Preferred stocking part highlighted in green. Outline Drawing CPFE500F Signals Connections Pin Function Housing - Molex 22-01-1 102 10 Do not connect Crimp - Molex 50802 series 9 Output good - ENA (or equivalents) 8 Tr im 7 Current share 6 Aux 5 +remote on/off 4 -remote on/off 3 Aux commo n 2 - Sense 1 + Sense dc output M6 x 18 stud for +ve output M6 x 18 stud for -ve output M6 nut, spring washer and flat washer supplied for each terminal ac input connector Housing Tyco 350766-4 Crimp 926895-1 (3 of f) or equivalent Earth 10 Neutral 1 Live Notes 1. All customer fixings 10 x M4 clearance holes 2. All tolerances +/-0.5m m For Additional Information, please visit us.tdk-lambda.com/lp/products/cpfe-series.htm 1-800-526-2324 * www.us.tdk-lambda.com/lp/ 25 Revision A8: Sept 2013 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK-Lambda: CPFE500F-48-NLC CPFE500F-12-DLC CPFE500F-28-DLC