RKJXT1F 4-directional Stick Switch (with Encoder / Center-push Function) A space-saving device with single shaft 4-directions/ push/encoder Typical SpecificationsStick Switches Items Specifications Ratingsmax. Resistive load 10mA 5V DC 4-direction Center-push Contact resistance 1 max. Operating angle4-direction Each direction 9max. TravelCenter push 0.30.2mm Total with 4-direction Center-push Operating life 50,000 cycles 50,000 cycles Typical SpecificationsEncoders Items Specifications Multi Control Devices Ratingsmax. Resistive load 10mA 5V DC Operating life 15,000 cycles Product Line Product No. Variable Resistor Type RKJXT1F42001 Stick Switches Operating force DirectionmNm Center-pushN Detent torque Maximum resolution 4 4025 52 Minimum order unit pcs. Encoder Number of detent Number of pulse 158mNm 30 Japan Export 1,320 2,640 15 Switch Type Packing Specifications Tray Number of packagespcs. 1 case / Japan 1 case / export packing 1,320 Export package measurementsmm 2,640 555x375x333 Dimensions Unit:mm PC board mounting hole dimensions Viewed from mounting side 5.78 o1 C 3.8 com Encoder B le For position lug ho Encoder A 1.5 3.8 3 3 A 6.98 4.65 .4 15 1.2 5.55 ole h o1 10- D o1 .1 1.5 2- 434 15.6 3.2 .5 8.6 D C 3 10.5 ax. 9 m B 5 0.3 A o1 3 4-14.5 17.4 1.8 Operating direction of lever 15.6 Encoder com Center push position Push switch ON stroke o2.5 4-17 B 2 3.75 Style Push Ground terminal 6.86 Fulcrum of lever operation Refer to P.451 for soldering conditions. RKJXT1F4-directional Stick Switch (with Encoder / Center-push Function) Output Relation Chart Between Lever Position and ON Position. Y Operating Direction Terminal Push-A A B C D Center push ON Push-B X B ON Push-C D X ON Push-D Push-Com A C ON ON ON ON ON Y ON Operating direction of lever. Circuit Diagram Stick Switch Encoder Multi Control Devices A B AC BD C D Encoder Encoder A Encoder A Encoder B B PushPush Test CircuitEncoder Terminal Encoder A 5k 5k Output SignalEncoder T A-Phase (Terminal Encoder ACom) OFF(5V) B-Phase (Terminal Encoder BCom) OFF(5V) Terminal Encoder B Encoder part Terminal Encoder Com Detent point Switch Type DC 5V Encoder Encoder Com Com Variable Resistor Type Com Com ON(0V) ON(0V) t1 t2 Chattering, bounce and phase difference indicate the time measured at constant 60rpm. Phase difference T: above 5ms. Chattering t1: below 4ms. Bounce t2: below 2ms. 435 Switch type Type RKJXM RKJXT1F Series RKJXW RKJXM1 RKJXM2 11 19.5 RKJXW1 RKJXW2 Photo W Dimensions typical value mm D H 17 6.6 61 75.5 5.45 26.5 17 Number of operating shafts Single-shaft Dual-shaft Single-shaft Dual-shaft Shaft material Metal The inner shaftMetal The outer shaftResin Metal Resin Directional resolution 10.5 36 48.5 4-direction 8-direction With Lever return mechanism With Center-push switch With Encoder With Without With Operating temperature range Directional operation Center-push Encoder -40 to 85 total with 4-direction 50,000 cycles total with 8-direction 100,000 cycles 15,000 cycles 15,000 cycles Output voltage Encoder resolution 15pulses/360 Automotive use 30,000 cycles for each direction 30,000 cycles 100,000 cycles 30,000 cycles Ratingmax.Resistive load Electrical performance 10mA 5V DC Insulation resistance Mechanical performance 4025mNm 52N Encoder detent torque 158mNm Terminal strength Actuator strength Environmental performance 15pulses/360 250V AC for 1min. Push operating force Push / pull directions Operating direction 100M min. 250V DC Voltage proof Directional operating force 60V AC for 2s 2.51.5N 3.52N 3020mNm 4016mNm Direction AB, BC, CD, DA 2520mNm 31.5N 128mNm 5N for 1min. 100NPush/Pull 100NPush, 50NPull 0.4Nm 0.3Nm -40 500h 85 500h 60, 90 to 95%RH 500h 434 436 100NPush 50N Cold Damp heat 10M min. 50V DC 360V AC for 2s Direction A, B, C, D 3020mNm Dry heat Page Switch Type Life cycle (availability) Variable Resistor Type Operating life Multi Control Devices Directional operating feeling tactile feeling 100N 40, 90 to 95%RH 500h 438 Switch Type Multi Control Devices Soldering Conditions 451 Switch Type Multi Control Devices Cautions 452 Note Indicates applicability to all products in the series. 425 Switch Type / Soldering Conditions Reference for Manual Soldering Tip temperature Soldering time No. of solders RKJXT1F, RKJXM, RKJXL, SLLB, SLLB5, SRBE, SKRH Series 3505 3s max. 1 time RKJXS 35010 3 -0 s 1 2 time max. Reference for Dip Soldering Preheating Soldering surface temperature Heating time Series Dip soldering No. of solders Soldering temperature Soldering time RKJXT1F, RKJXM 100 max. 2 min. max. 2605 51s 2 time max. RKJXL 120 max. 70s max. 260 max. 6s max. 2 time max. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2 CAKor CCTat soldering portioncopper foil surface . A heat resisting tape should be used for fixed measurement. Multi Control Devices Example of Reflow Soldering Condition Variable Resistor Type 300 A B 200 C D Switch Type Temperature 3. Temperature profile 100 Times Room temperature Pre-heating E max. G max. H max. F max. I max. Series A B C D E F G H I No. of reflows RKJXS 260 230 150 150 2 min. 10s 40s 4 min. 1 time SLLB5 250 230 150 150 2 min. 30s 1 time SKRH, SLLB, SRBE 260 230 180 150 2 min. 40s 1 time Notes 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board' s temperature greatly differs from that of the switch, depending on the material, size thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. 451