AWS5506-S14
GaAs IC SPDT Reflective Switch
Positive Control DC - 2.5 GHz
Advanced Product Information
Rev. 1
FEATURES
Low Insertion Loss (0.4 dB @ 0.9 GHz)
Complementary Positive Control Voltages (0/+3V to
0/+5V)
Positive Voltage Supply (+3 to +5 V)
Low DC Power Consumption
Ultra Miniature 6 Lead SOT-6 Package
DESCRIPTION
The AWS5506 is a Single Pole Double Throw GaAs MMIC
switch assembled in a SOT-6 plastic package. The AWS5506
is designed for analog and digital application that require for
insertion loss, small size, and low cost. State selection is
achieved with a complimentary positive voltage (requires
positive bias Vs, and blocking caps) or negative voltage (no Vs
or blocking caps required).
Typical applications include: selection of synthesizers,
filters, amplifiers in dual mode, and dual band handsets.
S14
SOT-6
6 Pin Plastic Package
ELECTRICAL SPECIFICATIONS AT 25 °C (0, +3V)
OPERATING CHARACTERISTICS AT 25° C (0, +3V)
1. All measurements made in a 50 ohm system, unless otherwise specified.
2. DC = 300 kHz.
3. Insertion loss changes by 0.003 dB/°C.
4. Insertion loss state.
5. Video feedthru measured with 1 ns rise time pulse and 500 MHz bandwidth.
retemaraP
1
ycneuqerF
2
niM pyT xaM tinU
ssoLnoitresnI
3
zHG5.0-CD
zHG0.1-CD
zHG0.2-CD
zHG5.2-CD
-
4.0
54.0
6.0
9.0
5.0
6.0
8.0
1.1
Bd
noitalosI
zHG5.0-CD
zHG0.1-CD
zHG0.2-CD
zHG5.2-CD
22
71
11
01
52
02
41
31
- Bd
RWSV
4
zHG0.1-CD
zHG5.2-CD -1:2.1
1:5.1
1:3.1
1:7.1 -
retemaraP noitidnoC ycneuqerF niM pyT xaM tinU
scitiretcarahCgnihctiwS
5
)FR%01/09ro%09/01(llaF,esiR
)FR%01/%09otLTC%05(ffO,nO
urhtdeeFoediV
- -
01
02
52
-
sn
sn
Vm
)3PI(tnioPtpecretnInoitaludomretnI mBd01+rewoPtupnIenot-owTroF zHG0.2-5.0 - 54+ - mBd
noisserpmoCBd1rofrewoPtupnI V3+@
V5+@
zHG0.2-5.0
zHG0.2-5.0 -12+
82+ - mBd
egatloVlortnoC
V
WOL
xaMAu02@V2.0ot0=
V
HGIH
xaMAu002@V5+otxaMAu001@V3+=
V
S
V=
HGIH
+V2.0
A
2
A
AWS5506-S14
Advanced Product Information - Rev. 0
ABSOLUTE MAXIMUM RATINGS
TRUTH TABLE
Positive Operation
PIN OUT
Characteristics Value
RF Input Power 2 W > 500 MHz, 0/+7 V Control
Control Voltag e -0.2 V, + 8 V
Operati ng Temperature -40° C to +125°C
Storage Temperature -50°C to +150°C
q
JC 25° C/W
V1V2J1 - J 2J1 - J3
VHigh 0 Insertion Isolation
0V
High Isolation Insertion
VHigh = +3 to +5 V (VS = VHigh + 0.2 V)
DC blocking capacitors (C1, 2, 4) and biasing resistor (R1)
must be supplied externally for positive voltage operation.
C1, 2, 4 = 100 pF for operation >500 MHz.
niPnoitcnuFnoitpircseD
1FR
1
)2J()tuptuonasadnatupninasadesuebnac(tropFR
2DNG)elbissopsatrohssapeek(noitcennocdnuorG
3FR
2
)3J()tuptuonasarotupninasadesuebnac(tropFR
42V)V5otV3hgiH,V0wol(2egatlovlortnoC
5FR
MOC
sV/)1J( lortnocevitisoprofegatlovsaibdnatropnommocFR
)V5otV3(
61V)V5otV3hgiH,V0wol(1egatlovlortnoC
123
456
V
2
V
1
V
s
GND
RF
2
(J3)
C
4
C
1
RF
1
(J2)
10K
W
C
2
RF
COM
(J1)
TEST CIRCUIT LAYOUT
Vs
3
ANADIGICS, Inc.
35 Technology Drive
Warren, New Jersey 07059
Tel: (908) 668-5000 / Fax: (908) 668-5132
Email: Mktg@anadigics.com
www.anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The Advanced Product
data sheets and product specifications contained in this data sheet are subject to change prior to a products formal introduction. The information in
this data sheet has been carefully checked and is assumed to be reliable. However, ANADIGICS assumes no repsponsibility for inaccuracies.
ANADIGICS strongly urges customers to verift that the informationn they are using is current before placing orders.
WARNING
ANADIGICS products are not intened for use in life support appliances, device, or systems. Use of an ANADIGICS product in any such
application without written consent is prohibited.
A
Advanced Product Information - Rev. 0
AWS5506-S14
PACKAGE OUTLINE DRAWING
θ
0.10−−−0.00A1
2.60
1°
0.37
1.40
2.70
0.10
0.35
0.70
θ1
D
H
L
e
E
b
C
A2
5° 9°
2.90
2.80
1.90(TYP)
−−−
1.60
0.15
0.40
0.80
3.10
3.00
−−−
1.80
0.50
0.25
0.90
DIM ENS IO NS IN MILLIMETERS
1.00
MIN
SYMBOLS
A1.10
NOM MAX
1.30 MAX
0.051
0.122
0.118
−−−
0.071
0.020
0.010
0.035
0.004
5° 9°1°
DIMENSIONS IN INCHES
0.075(TYP)
0.00
0.102
0.015
0.055
0.106
0.004
0.014
0.027
0.039
MIN
−−−
0.063
0.110
−−−
0.114
0.006
0.016
0.031
0.043
NOM
NOTES:
1. Package body sizes exclude mold
flash and gate burrs.
2. Dimension L is measured in gage
plane
3. Coplanarity: 0.1000 mm
4. Tolerance + 0.1000 mm (4 mil)
unless otherwise specified.
S506
