B85321-A2405-A630 - Siemens Semiconductors

Data Book Supplement

EMC-

Components

Feed-Through Capacitors

Feed-Through Filters

in Solderless MK P Techno logy

Vakatseite

(( 2 ))

Siemens Matsushita Components 9.98 3

1 General

MeshContact is a solderless technology new ly developed by Siemen s Matsushita Components. It

allows uniform concentric contacting o f MKP capacitor winds, avoiding the thermal stress caused

by soldering. The result is even better insertion loss, high insulati on resistance plus compact, small

casing.

Basically, feed- through components can be used to suppress interference in all electrical installa-

tions and equipment. The new ser ies is also ideal for telephone switching sy stems and base sta-

tions and, through broadband suppression effective into the GHz region, prevents interference pul-

ses from entering equipment from outs ide through the power supply network and vice versa.

There is now a building- block system available in this new technology for feed- through capacitors

and filters, allowing fast and attractively priced solutions to be implemented. Interim ratings can be

produced to order for special applic ations.

Selector guide

Diameter Voltage range Capacitance range

30 mm up to 75 A 0,1 ... 1 µF

55 mm up to 500 A 0,5 ... 4,7 µF

Feed- through elements fitted into a shielding wall

Feed- Through Capacitors

Feed- Through Filters B85121

B85321

4 9.98 Siemens Matsushita Components

In feed- through capacitors the conductor carrying the load current is c onnected concentrically to

one electrode and passes through the center of the capacitor. The other electrode makes concentric

contact with the capacitor case.

Feed- through c apacitors are designed to be effective from low frequency to far above 300 MHz.

The low- loss winding with high- stability contact to t he leads at its face ends is enclosed in a metal

case with either a threaded stud at one end or an external thread.

Feed- through filters have π filter circuits consis ting of two equal shunt capacitors and on e ferro-

magnetic inductor connected in series. Due to t he concentric arrangement of t he components, high

attenuation values are obtained for frequencies up to and exceeding 1 GHz.

Safety note!

If feed- through elements with high capacitances are used, protective measures (e.g. protective

earthing) in accordance with equipment/system regulations (product standards) are required!

2 Mounting instructions

To fully utilize their RF characteristics, feed- through components must be fitted directly into the

shielding wall. The component case must make perfect and unbroken (RF- tight!) contact with the

shielding. This can be best achieved by screwing them into a threaded hole or bushing, so that good

electrical contact is made by the flanks of the thread.

As an alternative, feed- through elements can be scr ewed into feed- through holes in a shielding

wall and held by a retaining nut. Contact between the case and the shielding wall is produc ed by

the contact surface on the thread.

The connecting line must be attached by f ixi ng it between two countered nuts in order to avoid ex-

posing the component to torque loads (use two spanners).

NOTE

Due to the danger of exposing the feed throughs to mechanical loads caused by shock and

vibration, it is not permissible to use rigid copper bars as connecting elements.

Feed- Through Capacitors

Feed- Through Filters B85121

B85321

Siemens Matsushita Components 9.98 5

Construction

●Building- block system

●MKP technology (dry, self- healing)

Dielectric: polypropylene, metallized

●Metal case with synthetic resin terminals

●For central screw fixing

Features

●Compact dimensions

●Variable current rating and capacitance

through building- block system

●High attenuation

●Simple fitting

●High contact reliability through

central screw fixing

Applications

Broadband interference suppression for

ac/dc supply lines, e.g. in

●shielded rooms

●telephone exchanges, base stations

●electrical machines and systems

●power supplies

Terminals

●Threaded studs

Marking

Manufacturer, ordering code, EMI suppression class,

rated capacitance, rated voltage, rated current,

climatic category, circuit diagram, date of manufacture (MM.YY)

Standards

Feed- thr ough c apacitors comply with EN 133 200

Feed- through filters comply with EN 133 400

Safety information

Due to the high capacitance ratings protective measures (e.g. protective earthing)

in accordance with equipment/system regulations are required.

Circuit diagrams

SSB1274-B

SSB1275-J

Feed- through filters Feed- through capacitors

Feed- Through Capacitors

Feed- Through Filters B85121

B85321

6 9.98 Siemens Matsushita Components

Feed- through capacitors ∅ 30 mm

Insertion loss (dB); typical values at 50 Ω

General technical data

Capacitance tolerance: ±20 %

IEC climatic category: 40/085/56 (– 40 °C/ + 85 °C, 56 days damp heat test)

Screw cap fixing: standard M20 × 1

Dimensional drawing

PTermi-

nal Dimensions

(mm) Ordering code

A µF Vac Vdc Vdc ∅ ×

25 0,1 250 600 3000 M6 ∅ 30 × 55 110 B85121- A2104- A250

0,5 250 600 2500 M6 ∅ 30 × 55 110 B85121- A2504- A250

1,0 250 600 2000 M6 ∅ 30 × 55 110 B85121- A2105- A250

75 0,1 250 600 3000 M6 ∅ 30 × 55 110 B85121- A2104- A750

0,5 250 600 2500 M6 ∅ 30 × 55 110 B85121- A2504- A750

1,0 250 600 2000 M6 ∅ 30 × 55 110 B85121- A2105- A750

Capacitance

R10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz

0,1 µF 0 520406070

0,5 µF 2 15 35 40 80 > 90

1,0 µF 5 25 45 50 85 > 90

SSB1271-L

Marking

M20x1

ø30

Feed- Through Capacitors B85121

Siemens Matsushita Components 9.98 7

Feed- through capacitors ∅ 55 mm

Insertion loss (dB); typical values at 50 Ω

PTermi-

nal Dimensions

(mm) Ordering code

A µF Vac Vdc Vdc M ∅ ×

63 0,5 250 600 3000 M6 55 × 30 100 B85121- A2504- A630

1,0 250 600 2500 M6 55 × 30 100 B85121- A2105- A630

2,0 250 600 2500 M6 55 × 60 130 B85121- A2205- A630

4,7 250 600 2000 M6 55 × 60 130 B85121- A2475- A630

100 0,5 250 600 3000 M8 55 × 30 110 B85121- A2504- A101

1,0 250 600 2500 M8 55 × 30 110 B85121- A2105- A101

2,0 250 600 2500 M8 55 × 60 140 B85121- A2205- A101

4,7 250 600 2000 M8 55 × 60 140 B85121- A2475- A101

200 0,5 250 600 3000 M10 55 × 30 120 B85121- A2504- A201

1,0 250 600 2500 M10 55 × 30 120 B85121- A2105- A201

2,0 250 600 2500 M10 55 × 60 150 B85121- A2205- A201

4,7 250 600 2000 M10 55 × 60 150 B85121- A 2475- A20 1

Capacitance

R10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz

0,5 µF 2 15 35 40 80 > 90

1,0 µF 5 25 45 50 85 > 90

2,0 µF 10305055> 90> 90

4,7 µF 15355565> 90> 90

Feed- Through Capacitors B85121

8 9.98 Siemens Matsushita Components

General technical data

Capacitance tolerance: ±20 %

IEC climatic category: 40/085/56 (– 40 °C/ + 85 °C, 56 days damp heat test)

Screw cap fixing standard M32 × 1,5;

special fixing M27 × 1,5 possible.

Dimensional drawing

B1272-U

SW41

55±1

SW17

24 min.

M32x1,5

15+1

Marking

Feed- Through Capacitors B85121

Siemens Matsushita Components 9.98 9

Feed- through filters ∅ 30 mm

Insertion loss (dB); typical values at 50 Ω, load - inde p e nded

General technical data

Capacitance tolerance: ±20 %

IEC climatic category: 40/085/56 (– 40 °C/ + 85 °C, 56 days damp heat test)

screw cap fixing: standard M20 × 1

Dimensional drawing

PTermi-

nal Dimensions

(mm) Ordering code

A µF Vac Vdc Vdc ∅ ×

25 2 × 0,1 250 600 3000 M6 30 × 81 130 B85321- A2204- A250

2 × 0,5 250 600 2000 M6 30 × 81 130 B85321- A 2105- A250

2 × 1,0 250 500 1700 M6 30 × 81 130 B85321- A 2205- A250

75 2 × 0,1 250 600 3000 M6 30 × 81 130 B85321- A 2204- A750

2 × 0,5 250 600 2000 M6 30 × 81 130 B85321- A2105- A750

2 × 1,0 250 500 1700 M6 30 × 81 130 B85321- A2205- A750

Capacitance

R10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz

2 × 0,1 µF 2 10 25 70 > 100 > 100

2 × 0,5 µF 5 25 45 80 > 100 > 100

2 × 1,0 µF 10306090> 100> 100

SSB1271-L

Marking

M20x1

ø30

Feed- Through Filters B85321

10 9.98 Siemens Matsushita Components

Feed- through filters ∅ 55 mm

Insertion loss (dB); typical values at 50 Ω, load - inde p e nded

PTermi-

nal Dimensions

(mm) Ordering code

A µF Vac Vdc Vdc M ∅ ×

63 A 2 × 0,5 µF 250 600 3000 M6 55 × 100 166 B85321- A2105- A630

2 × 1,0 µF 250 600 2500 M6 55 × 100 166 B85321- A2205- A630

2 × 2,0 µF 250 600 2500 M6 55 × 100 166 B85321- A2405- A630

2 × 4,7 µF 250 600 1650 M6 55 × 100 166 B85321- A2945- A630

100 A 2 × 0,5 µF 250 600 3000 M8 55 × 100 180 B85321- A2105- A101

2 × 1,0 µF 250 600 2500 M8 55 × 100 180 B85321- A2205- A101

2 × 2,0 µF 250 600 2500 M8 55 × 100 180 B85321- A2405- A101

2 × 4,7 µF 250 600 1650 M8 55 × 100 180 B85321- A2945- A101

200 A 2 × 0,5 µF 250 600 3000 M10 55 × 100 185 B85321- A2105- A201

2 × 1,0 µF 250 600 2500 M10 55 × 100 185 B85321- A2205- A201

2 × 2,0 µF 250 600 2500 M10 55 × 100 185 B85321- A2405- A201

2 × 4,7 µF 250 600 1650 M10 55 × 100 185 B85321- A2945- A201

300 A 2 × 0,5 µF 250 600 3000 M12 55 × 100 195 B85321- A2105- A301

2 × 1,0 µF 250 600 2500 M12 55 × 100 195 B85321- A2205- A301

2 × 2,0 µF 250 600 2500 M12 55 × 100 195 B85321- A2405- A301

2 × 4,7 µF 250 600 1650 M12 55 × 100 195 B85321- A2945- A301

400 A 2 × 0,5 µF 250 600 3000 M16 55 × 130 245 B85321- A2105- A401

2 × 1,0 µF 250 600 2500 M16 55 × 130 245 B 85321- A2205- A401

2 × 2,0 µF 250 600 2500 M16 55 × 130 245 B85321- A2405- A401

2 × 4,7 µF 250 600 1650 M16 55 × 130 245 B85321- A2945- A401

500 A 2 × 0,5 µF 250 600 3000 M18 55 × 130 250 B85321- A2105- A501

2 × 1,0 µF 250 600 2500 M18 55 × 130 250 B85321- A2205- A501

2 × 2,0 µF 250 600 2500 M18 55 × 130 250 B85321- A2405- A501

2 × 4,7 µF 250 600 1650 M18 55 × 130 250 B85321- A2945- A501

Capacitance

R10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz

2 × 0,5 µF 5 25 45 80 > 100 > 100

2 × 1,0 µF 10 30 60 > 100 > 100 > 100

2 × 2,0 µF 15 35 70 > 100 > 100 > 100

2 × 4,7 µF 25 40 90 > 100 > 100 > 100

Feed- Through Filters B85321

Siemens Matsushita Components 9.98 11

General technical data

Capacitance tolerance: ±20 %

IEC climatic category: 40/085/56 (– 40 °C/ + 85 °C, 56 days damp heat test)

Screw cap fixing: standard M32 × 1,5

special fixing M27 × 1,5 possible for filters up to 300 A.

Dimensional drawing

SSB1273-3

SW10

SW41

55±1 15 min. 8 15+1

345

15 min.

M32x1,5

Marking

Feed- Through Filters B85321

12 9.98 Siemens Matsushita Components

Published by Siemens Matsushita Components GmbH & Co. KG

Marketing Kommunikation, Postfach 80 17 09, D- 81617 München

s far as patent s or other rights of third parties are concerned, liability is only assumed for compo-

nents per se, not for applications, processes and circuits implemented within components or

assemblies.

he information describes the type of component and shall not be considered as assured

characteristics.

erms of delivery and rights to change design reserved.

his brochure replaces the previous edition.

For questions on technology, prices and delivery please contact the Sales Offices of Siemens AG,

Passive Components and Electron Tubes Group, in the Federal Republic of Germany or the inter-

national Siemens Companies and Representativ es.

Due to technical requirements components may contain dangerous substances. For information on

he type in question please also contact one of our Sales Offices.