http://www.tracopower.com
DC/DC Converters
TEL 30 Series, 30 Watt
Features
◆ Highest power density: 30W in
51x25x9.6mm package
◆ Industry standard footprint
◆ Very high ffficiency
◆ Models with low output
Voltages: 2.5 & 3.3VDC
◆ Output voltage adjustable
◆ Optional remote On/Off
◆ Under voltage lockout
◆ Operating temperature range
–40°C to +71°C
◆ Six-side shielded metal case
◆ Lead free design, RoHS compliant
◆ 3-year product warranty
The TEL 30 Series is a new range of cost efficient, isolated 30W converters in a
shielded metal case with excellent specification. The 10 models in this series feature
2:1 input range with 18-36 or 36-75 VDC. Overload and over voltage protection,
under voltage shutdown as well as remote On/Off are features of this converter.
Typical applications for the TEL 30 Series converter are communication and net-
working systems, industrial electronics and distributed power architectures.
Ordercode Input voltage range Output voltage Output current max. Efficiency
TEL 30-2409 2.5 VDC 6‘000 mA 84 %
TEL 30-2410 3.3 VDC 6’000 mA 86 %
TEL 30-2411 18 – 36 VDC 5.1 VDC 5’000 mA 88 %
TEL 30-2412 (nominal 24 VDC) 12 VDC 2’500 mA 88 %
TEL 30-2413 15 VDC 2’000 mA 88 %
TEL 30-4809 2.5 VDC 6‘000 mA 84 %
TEL 30-4810 3.3 VDC 6’000 mA 86 %
TEL 30-4811 36 – 75 VDC 5.1 VDC 5’000 mA 88 %
TEL 30-4812 (nominal 48 VDC) 12 VDC 2’500 mA 88 %
TEL 30-4813 15 VDC 2’000 mA 88 %
Models
Page 1 of 3
UL 60950 -1
C B
Scheme
http://www.tracopower.com
DC/DC Converters
TEL 30 Series 30 Watt
Input Specifications
Input current at no load 24 Vin models: 70 mA typ.
48 Vin models: 50 mA typ.
Start-up voltage / 24 Vin models: 17.8 VDC / 15.8 VDC
under voltage shut down 48 Vin models: 36 VDC / 33 VDC
Surge voltage 24 Vin models: 50 V max.
(100 msec. max.) 48 Vin models: 100 V max.
Output Specifications
Voltage set accuracy ±1.0 % max.
Output voltage adjustment ±10 %
Regulation – Input variation Vin min. to Vin max. 0.3 % max.
– Load variation 10 – 100 % 1.0 % max.
Ripple and noise (20 MHz Bandwidth) 100 mVpk-pk max.
Temperature coefficient ±0.02 %/K
Output current limitation 110 % – 140 % Iout max., foldback
Short circuit protection hiccup mode, indefinite (automatic recovery)
Capacitive load 2.5 / 3.3 / 5.1 VDC models: 6800 µF max.
12 / 15 VDC models: 680 µF max.
General Specifications
Temperature ranges – Operating –40°C to +71°C (with derating)
– Case temperature +105°C max.
– Storage –50°C to +125°C
Derating 2 %/K above 50°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >600’000 h
Isolation voltage (60 sec.) – Input/Output 1500 VDC
Isolation capacitance – Input/Output 1200 pF typ.
Isolation resistance – Input/Output >1000 Mohm
Remote On/Off – On: 2.5 to 100 VDC or open circuit.
(optional) – Off: –1.0 to +1.0 VDC or short circuit pin 3 and pin 2
– Off idle current: 5 mA max.
Switching frequency (fixed) 350 kHz typ. (pulse width modulation PWM)
Safety standards UL/cUL 60950-1, IEC/EN 60950-1
Physical Specifications
Casing material aluminum
Potting material epoxy (UL 94V-0 rated)
Weight 32 g (1.13 oz )
Soldering temperature max. 265°C / 10 sec.
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHS directive 2011/65/EU
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Page 2 of 3
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
DC/DC Converters
TEL 30 Series 30 Watt
Outline Dimensions
10.2
5.08
50.8
(2.0)
(0.4)
(0.2)
Bottom View
14
3
2
6
45.72
5
(1.8)
2.54
(0.1)
7.62
(0.3)
17.78
(0.7)
10.16
(0.4)
20.32
(0.8)
25.4
(1.0)
2.54
(0.1)
2.54
(0.1)
Pin
1+Vin (Vcc)
2–Vin (GND)
3Remote On/Off
(optional)
4+Vout
5–Vout
6Trim
Pin-Out
Dimensions in [mm], () = Inch
Pin diameter: 1.0 ±0.05 (0.039 ±0.002)
Pin pitch tolerance: ±0.13 (±0.005)
Case tolerances: ±0.25 (±0.01)
Rev. July 13, 2018
Output Voltage Adjustment
Trim up Trim down Trim up/down
Rd
Trim
+Vout
Ru
Trim
- Vout
CW
10K
Pot.
CCW
–Vout
Trim
+Vout
Ru [kOhm] = (33 x Vout) – ( 30 x Vadj)
Vadj – Vout Rd [kOhm]= (36.667 x Vadj) – (33 x Vout)
Vout – Vadj
Page 3 of 3
Note:
Before attaching the heatsink, the product
label on converter has to be removed for
optimal performance.
For volume orders we can supply the
converters with heatsink already mounted.
Please contact us for a relative quotation.
Order code: TEN-HS4
(cont.: heat-sink, thermal pad, 2 clamps)
Material: Aluminum
Finish: Anodic treatment (black)
Weight: 9 g (0.31oz) without converter
Thermal impedance after assembling: 10 K/W
17.2 (0.68)
max.
Converter
Heat-sink
Thermal pad
Clamp
31.0 (1.22)
max.
31.1 (1.22)
Heat-sink TEN-HS4 (optional)
Heat-Sink (Option)
