IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE FAST CMOS 16-BIT REGISTER (3-STATE) IDT74FCT162374AT/CT/ET FEATURES: DESCRIPTION: * * * * * * * * The FCT162374T 16-bit edge-triggered D-type registers are built using advanced dual metal CMOS technology. These high-speed, low-power registers are ideal for use as buffer registers for data synchronization and storage. The Output Enable (xOE) and clock (xCLK) controls are organized to operate each device as two 8-bit registers or one 16-bit register with common clock. Flow-through organization of signal pins simplifies layout. All inputs are designed with hysteresis for improved noise margin. The FCT162374T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot, and controlled output fall times-reducing the need for external series terminating resistors.The FCT162374T are plug-in replacements for the FCT16374T and ABT16374 for on-board bus interface applications. 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1A (max.) VCC = 5V 10% Balanced Output Drivers: 24mA Reduced system switching noise Typical VOLP (Output Ground Bounce) < 0.6V at VCC = 5V, TA = 25C * Available in SSOP and TSSOP packages FUNCTIONAL BLOCK DIAGRAM 1OE 2OE 1CLK 2CLK 1D1 D 2D1 D 1O1 2O1 C C TO SEVEN OTHER CHANNELS TO SEVEN OTHER CHANNELS The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE SEPTEMBER 2009 1 (c) 2009 Integrated Device Technology, Inc. DSC-5453/7 IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION 1OE 1 48 1CLK 1O1 2 47 1D1 1O2 3 46 1D2 GND 4 45 GND 1O3 5 44 1D3 1O4 6 43 1D4 VCC 7 42 VCC 1O5 8 41 1D5 1O6 9 40 1D6 GND 10 39 GND 1O7 11 38 1D7 1O8 12 37 1D8 2O1 13 36 2D1 2O2 14 35 2D2 GND 15 34 GND 2O3 16 33 2D3 2O4 17 32 2D4 VCC 18 31 2O5 19 2O6 Symbol Description Max Unit VTERM(2) Terminal Voltage with Respect to GND -0.5 to 7 V VTERM(3) Terminal Voltage with Respect to GND -0.5 to VCC+0.5 V TSTG Storage Temperature -65 to +150 C IOUT DC Output Current -60 to 120 mA NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXX Output and I/O terminals. 3. Output and I/O terminals terminals for FCT162XXX. CAPACITANCE (TA = +25C, F = 1.0MHz) Parameter(1) Symbol Conditions Typ. Max. Unit CIN Input Capacitance VIN = 0V 3.5 6 pF COUT Output Capacitance VOUT = 0V 3.5 8 pF NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names Description xDx Data Inputs xCLK Clock Inputs VCC xOx 3-State Outputs 30 2D5 xOE 3-State Outputs Enable Input (Active LOW) 20 29 2D6 GND 21 28 GND 2O7 22 27 2D7 2O8 23 26 2D8 2OE 24 25 2CLK FUNCTION TABLE(1) Inputs xDx xCLK xOE xOx X L H Z X H H Z Load L L L Register H L H L H Z H H Z Function Hi-Z SSOP/ TSSOP TOP VIEW NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Z = High-Impedance = LOW-to-HIGH transition 2 Outputs IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 10% Symbol Test Conditions(1) Parameter Min. Typ.(2) Max. Unit VIH Input HIGH Level Guaranteed Logic HIGH Level 2 -- -- V VIL Input LOW Level Guaranteed Logic LOW Level -- -- 0.8 V IIH Input HIGH Current (Input pins)(5) VCC = Max. -- -- 1 A -- -- 1 -- -- 1 -- -- 1 VO = 2.7V -- -- 1 VO = 0.5V -- -- 1 -- -0.7 -1.2 V -80 -140 -250 mA -- 100 -- mV -- 5 500 A Min 60 -60 2.4 Typ.(2) 115 -115 3.3 Max. 200 -200 -- Unit mA mA V -- 0.3 0.55 V VI = VCC Input HIGH Current (I/O pins)(5) IIL Input LOW Current (Input pins)(5) VI = GND Input LOW Current (I/O pins)(5) IOZH High Impedance Output Current IOZL (3-State Output pins)(5) VIK Clamp Diode Voltage IOS Short Circuit Current VH Input Hysteresis ICCL ICCH ICCZ Quiescent Power Supply Current VCC = Max. VCC = Min., IIN = -18mA VCC = Max., VO = GND(3) -- VCC = Max. VIN = GND or VCC A A OUTPUT DRIVE CHARACTERISTICS Symbol IODL IODH VOH Parameter Output LOW Current Output HIGH Current Output HIGH Voltage VOL Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3) VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3) VCC = Min IOH = -24mA VIN = VIH or VIL VCC = Min IOL = 24mA VIN = VIH or VIL NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter is 5A at TA = -55C. 3 IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Min. Typ.(2) Max. Unit -- 0.5 1.5 mA VIN = VCC VIN = GND -- 60 100 A/ MHz VCC = Max. Outputs Open fCP = 10MHz VIN = VCC VIN = GND -- 0.6 1.5 mA 50% Duty Cycle xOE = GND fi = 5MHz 50% Duty Cycle One Bit Toggling VIN = 3.4V VIN = GND -- 1.1 3 VCC = Max. Outputs Open fCP = 10MHz 50% Duty Cycle VIN = VCC VIN = GND -- 3 5.5(5) xOE = GND Sixteen BitsTogging fi = 2.5MHz 50% Duty Cycle VIN = 3.4V VIN = GND -- 7.5 19(5) Test Conditions(1) Symbol Parameter ICC Quiescent Power Supply Current TTL Inputs HIGH VCC = Max. VIN = 3.4V(3) ICCD Dynamic Power Supply Current(4) VCC = Max. Outputs Open xOE = GND One Input Togging 50% Duty Cycle Total Power Supply Current(6) IC NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCPNCP/2 + fiNi) ICC = Quiescent Current (ICCL, ICCH and ICCZ) ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) NCP = Number of Clock Inputs at fCP fi = Input Frequency Ni = Number of Inputs at fi 4 IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE SWITCHING CHARACTERISTICS OVER OPERATING RANGE Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tSU tH tW tSK(o) Parameter Propagation Delay xCLK to xOx Output Enable Time Condition(1) CL = 50pF RL = 500 74FCT162374AT Min.(2) Max. 2 6.5 74FCT162374CT Min.(2) Max. 2 5.2 74FCT162374ET Min.(2) Max. 1.5 3.7 Unit ns 1.5 6.5 1.5 5.5 1.5 4.4 ns Output Disable Time 1.5 5.5 1.5 5 1.5 3.6 ns Set-up Time HIGH or LOW, xDx to xCLK Hold Time HIGH or LOW, xDx to xCLK xCLK Pulse Width HIGH or LOW Output Skew(3) 2 1.5 5 -- -- -- -- 0.5 2 1.5 5 -- -- -- -- 0.5 1.5 0 3(4) -- -- -- -- 0.5 ns ns ns ns NOTES: 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design. 4. This limit is guaranteed but not tested. 5 IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS V CC SWITCH POSITION 7.0V 500 Test Switch Open Drain Disable Low Enable Low Closed All Other Tests Open V OUT VIN Pulse Generator DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. D.U.T. 50pF RT 500 CL Test Circuit for All Outputs DATA INPUT tH tSU TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC. tREM tSU 3V 1.5V 0V 3V 1.5V 0V LOW-HIGH-LOW PULSE 1.5V tW 3V 1.5V 0V HIGH-LOW-HIGH PULSE 1.5V 3V 1.5V 0V tH Pulse Width Set-up, Hold and Release Times ENABLE SAME PHASE INPUT TRANSITION tPLH tPHL OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL 3V 1.5V 0V VOH 1.5V VOL DISABLE 3V CONTROL INPUT tPZL OUTPUT NORMALLY LOW 3V 1.5V 0V SWITCH CLOSED tPLZ 3.5V 1.5V tPZH OUTPUT NORMALLY HIGH SWITCH OPEN 1.5V 0V 3.5V 0.3V VOL tPHZ 0.3V 1.5V 0V VOH 0V Propagation Delay Enable and Disable Times NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate 1.0MHz; tF 2.5ns; tR 2.5ns. 6 IDT74FCT162374AT/CT/ET FAST CMOS 16-BIT REGISTER (3-STATE) INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION XX FCT Temp. Range XXX Family XXXX Device Type XX Package PVG PAG Shrink Small Outline Package - Green Thin Shrink Small Outline Packag - Green 374AT 374CT 374ET 16-Bit Register (3-State) 162 Double-Density, 5 Volt, Balanced Drive 74 40 C to +85 C Datasheet Document History 09/06/09 Pg.6 Updated the ordering information by removing the "IDT" notation and non RoHS part. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 7 for Tech Support: logichelp@idt.com