SENSOR SOLUTIONS ///MSP100
Page 1
09/2017
MSP100
Pressure Transducer
SPECIFICATIONS
Analog and 14-Bit Digital Output
Small Size
Low Cost
316L Stainless Steel or 17-4PH
The MSP100 pressure transducer provides stainless
steel media compatibility in a low cost, small profile solution. This
sensor has no silicone gel or polymeric media isolation methods
to fail in contact with water or other harsh chemicals. Pressure
connections are provided via an O-ring seal. The device is
available in both analog and 14-bit digital output with a port
material of either 316L SS or 17-4PH. Additional custom port
options available to meet your application needs. The small size
vs. performance and media compatibility are provided through
solid-state technology.
APPLICATIONS
Beverage Dispensing Systems
Water Pressure or Flow Monitor
Medical Equipment
Industrial Equipment/Hydraulics
Tank Level Measurement
Manifold Pressure
FEATURES
Single Piece Construction;
No Welds, No Oil
100% Stainless Steel Isolation for
Harsh Chemical Measurement
Low Cost
14-Bit Digital Output or Analog
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 2
STANDARD RANGES
Range
psig
0 to 100
0 to 150
0 to 250
0 to 500
PERFORMANCE SPECIFICATIONS (ANALOG, OUTPUT SIGNAL “2”)
Ambient Temperature: 25°C (unless otherwise specified)
PARAMETERS
MIN
TYP
MAX
UNITS
NOTES
Supply Voltage
4.75
5.00
5.25
VDC
Zero Offset
-2
2
mV
Ratiometric
Span
98
100
102
mV
Ratiometric
Current Consumption
2
mA
Proof Pressure
1.5X
Rated
Burst Pressure
3X
Rated
Endurance
1E+6
0~FS Cycles
Accuracy
-0.5
±0.2
0.5
%Span
RSS of BFSL: Linearity,
Hysteresis, Repeatability
Long Term Stability
0.25
%Span
Minimum Resistance between
Transducer and Body
50
MΩ
@250VDC
Thermal Zero Shift
-2.0
2.0
%Span
Reference to 25°C over
Compensated Temperature
Thermal Span Shift
-2.0
2.0
%Span
Reference to 25°C over
Compensated Temperature
Compensation Temperature
0
45
°C
Operating Temperature
0
55
°C
Response Time (10% to 90%)
0.1
ms
Vibration
±20g MIL-STD-810C, Procedure 514.2, Figure 514.2-2, Curve L
Shock
50g, 11 msec half sine shock per mil standard 202F. Method 213B, Condition A
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 3
PERFORMANCE SPECIFICATIONS (DIGITAL, OUTPUT SIGNAL “J” OR “S”)
Ambient Temperature: 25°C (unless otherwise specified)
PARAMETERS
MIN
TYP
MAX
UNITS
NOTES
Supply Voltage
2.7
3.0
5.0
VDC
Output at Zero Pressure
720
1000
1280
Count
Output at FS Pressure
14,720
15,000
15,280
Count
Current Consumption
3
mA
Proof Pressure
1.5X
Rated
Burst Pressure
3X
Rated
Endurance
1E+6
0~FS Cycles
Accuracy
-0.5
0.5
%Span
RSS of BFSL: Linearity,
Hysteresis, Repeatability
A/D Resolution
14
Bit
Operating Temperature
0
55
°C
Temperature Accuracy
-3
3
°C
1*
Thermal Zero Shift
-2.0
2.0
%F.S.
Reference to 25°C over
Compensated Temperature
Thermal Span Shift
-2.0
2.0
%F.S.
Reference to 25°C over
Compensated Temperature
Compensated Temperature
0
45
°C
Response Time (10% to 90%)
3
ms @ 4MHz
Without Sleep Mode
Response Time (10% to 90%)
8.4
ms @ 4MHz
With Sleep Mode
Vibration
±20g MIL-STD-810C, Procedure 514.2, Figure 514.2-2, Curve L
Shock
50g, 11 msec half sine shock per mil standard 202F. Method 213B, Condition A
Notes:
1* Reflect pressure port diaphragm temperature over the compensated temperature range
2* Response time is from power on to reading measurement data.
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 4
DIMENSIONS
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 5
WIRING
Analog mV Output Wiring
Connection
PIN 1
PIN 2
PIN 3
PIN 4
Molex 4pin Connector
+SUPPLY
+OUTPUT
-OUTPUT
-SUPPLY
PCB Mount
Digital I2C Output Wiring
Connection
PIN 1
PIN 2
PIN 3
PIN 4
Molex 4pin Connector
VDD
GND
SDA
SCL
PCB Mount
Digital SPI Output Wiring
Connection
PIN 1
PIN 2
PIN 3
PIN 4
PIN5
Molex 5pin Connector
VDD
GND
MISO
SCLK
SS
PCB Mount
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 6
SENSOR OUTPUT
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 7
TEMPERATURE OUTPUT
OUTPUT SIGNAL
Code
Output Signal
Supply Voltage (V)
2
0 – 100mV
5 ± 0.25
J
I2C
2.7 – 5.0
S
SPI
2.7 – 5.0
MSP100
Pressure Transducer
SENSOR SOLUTIONS ///MSP100
09/2017
Page 8
ORDERING INFORMATION
MS1 S 1 – 1 0 0 0 0 J- 100P G
Output
Code
Type
Supply
Voltage
2
0 - 100mV
5±0.25V
J*
I2C
2.7 – 5.0V
S*
SPI
2.7 – 5.0V
Pressure Type
G
Gauge
Pressure Ranges
psi
100P
150P
250P
500P
Port Type Selection
Code
Port Type
J
O-ring Face Seal
U
O-ring Radial Seal
Cable/Connector
Code
Connection Type
1
Cable, 2 feet with Molex Connector
Port Material
0
316L Stainless Steel
1
17-4PH Stainless Steel
I2C Address (Digital Only)
Code
Address
0
0x28H
1
0x36H
2
0x46H
3
0x48H
4
0x51H
Cleaning
0
No Selection
1
Oxygen Clean B40.1 Level IV
Sleep (Digital Only)
0
Non-Sleep Mode
1
Sleep mode
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2015 TE Connectivity Ltd. family of companies All Rights Reserved.
NORTH AMERICA
Measurement Specialties, Inc.,
a TE Connectivity Company
Phone: 800-522-6752
Email: customercare.frmt@te.com
EUROPE
Measurement Specialties (Europe), Ltd.,
a TE Connectivity Company
Phone: +31-73-624-6999
Email: customercare.lcsb@te.com
ASIA
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
Phone: 0400-820-6015
Email: customercare.shzn@te.com
SPI Default Code “0”
*Digital Output
