MCP39F501 Single-Phase, Power-Monitoring IC with Calculation and Event Detection Features: Description: * Power Monitoring Accuracy capable of 0.1% error across 4000:1 dynamic range * Fast Calibration Routines * Programmable Event Notifications such as overcurrent and voltage sag, surge protection * 512 bytes User-accessible EEPROM through page read/write commands * Non-volatile On-chip Memory, no external memory required * Built-in calculations on fast 16-bit processing core - Active, Reactive and Apparent Power - True RMS Current, RMS Voltage - Line Frequency, Power Factor * Two-Wire Serial Protocol using a 2-wire Universal Asynchronous Receiver/Transmitter (UART) interface supporting multiple devices on a single bus * Low-Drift Internal Voltage Reference, 10 ppm/C typical * 28-lead 5x5 QFN package * Extended Temperature Range -40C to +125C The MCP39F501 is a highly integrated, single-phase power-monitoring IC designed for real-time measurement of input power for AC/DC power supplies, power distribution units and industrial applications. It includes dual-channel delta sigma ADCs, a 16-bit calculation engine, EEPROM and a flexible 2-wire interface. An integrated low-drift voltage reference with 10 ppm/C in addition to 94.5 dB of SINAD performance on each measurement channel allows for better than 0.1% accurate designs across a 4000:1 dynamic range. DIO3 REFIN+/OUT MCLR DGND DR MCP39F501 5x5 QFN* DVDD DGND Package Type 28 27 26 25 24 23 22 21 AGND MODE/DIR 1 NC 2 20 AN_IN/DIO2 NC 3 19 V1+ EP 29 UART_RX 4 Applications: COMMONA 5 * Real-time Measurement of Input Power for AC/DC supplies * Intelligent Power Distribution Units 18 V117 I116 I1+ OSCI 6 OSCO 7 A0/DIO0 UART_TX * Includes Exposed Thermal Pad (EP); see Table 3-1. COMMONB AVDD NC RESET 9 10 11 12 13 14 NC 15 A1/DIO1 8 Functional Block Diagram OSCO Internal Oscillator AVDD I1+ + PGA - 24-bit Delta Sigma Multi-level Modulator ADC I1V1+ + PGA - 24-bit Delta Sigma Multi-level Modulator ADC V1- AN_IN/DIO2 2013 Microchip Technology Inc. 10-bit SAR ADC AGND DVDD SINC3 Digital Filter Timing Generation SINC3 Digital Filter OSCI DGND UART Serial Interface 16-BIT CORE FLASH UART_TX UART_RX MODE/DIR A0/DIO0 Calculation Engine (CE) Configurable Digital Outputs A1/DIO1 AN_IN/DIO2 DIO3 DS20005256A-page 1 MCP39F501 MCP39F501 Typical Application - Single Phase, Two-Wire Application Schematic 10 1 F LOAD AVDD DVDD RESET REFIN/OUT+ I1+ 0.1 F 33 nF 0.5 m 1 m 2 m 4 m - 0.1 F 0.1 F 1 k + +3.3V UART_TX 1 k to MCU UART I133 nF 1 k UART_RX V1- to MCU UART 33 nF MCP39F501 720 k (OPTIONAL) V1+ 1 k 33 nF N.C. Leave Floating Connect on PCB +3.3V MCP9700A MODE/DIR NC NC NC NC DR COMMONA,B A0/DIO0 Address setting for multiple devices or Alarm with Event Functions A1/DIO1 DIO3 TEMPIN/DIO2 DIO2 OSCO 4 MHz OSCI 22 pF DGND AGND 22 pF (OPTIONAL) +3.3V 0.47 F 470 MCP1754 0.01 F N L DGND DS20005256A-page 2 470 F AGND 2013 Microchip Technology Inc. MCP39F501 1.0 ELECTRICAL CHARACTERISTICS Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings DVDD .....................................................................-0.3 to 4.5V AVDD .....................................................................-0.3 to 4.0V Digital inputs and outputs w.r.t. AGND ................. -0.3V to 4.0V Analog Inputs (I+,I-,V+,V-) w.r.t. AGND ............... ....-2V to +2V VREF input w.r.t. AGND .............................-0.6V to AVDD +0.6V Maximum Current out of DGND pin..............................300 mA Maximum Current into DVDD pin.................................250 mA Maximum Output Current Sunk by Digital IO ................25 mA Maximum Current Sourced by Digital IO.......................25 mA Storage temperature .....................................-65C to +150C Ambient temperature with power applied......-40C to +125C Soldering temperature of leads (10 seconds) ............. +300C ESD on the analog inputs (HBM,MM) ................. 4.0 kV, 200V ESD on all other pins (HBM,MM) ........................ 4.0 kV, 200V 1.1 Specifications TABLE 1-1: ELECTRICAL CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6 V, TA = -40C to +125C, MCLK = 4 MHz, PGA GAIN = 1. Characteristic Sym. Min. Typ. Max. Units Test Conditions Active Power (Note 2) P -- 0.1 -- % 4000:1 Dynamic Range on Current Channel (Note 1) Reactive Power (Note 2) Q -- 0.1 -- % 4000:1 Dynamic Range on Current Channel (Note 1) Apparent Power (Note 2) S -- 0.1 -- % 4000:1 Dynamic Range on Current Channel (Note 1) Current RMS (Note 2) IRMS -- 0.1 -- % 4000:1 Dynamic Range on Current Channel (Note 1) Voltage RMS (Note 2) VRMS -- 0.1 -- % 4000:1 Dynamic Range on Voltage Channel (Note 1) Power Factor (Note 2) -- 0.1 -- % VRMS -- 0.1 -- % Power Measurement Line Frequency (Note 2) Calibration, Calculation and Event Detection Times Auto-Calibration Time -- tCAL N Minimum Calculation tCALC_EVENT 2 x (1/fLINE) and Event Detection Time Minimum Time for Voltage Sag Detection Note 1: 2: 3: 4: 5: 6: 7: tAC_DROP -- 2N x (1/fLINE) -- ms -- -- ms see -- ms Note 7 Note 4 Section 7.7 Specification by design and characterization; not production tested. Calculated from reading the register values. VIN = 1VPP = 353 mVRMS @ 50/60 Hz. Applies to Voltage Sag and Voltage Surge Events Only. Variation applies to internal clock and UART only. All calculated output quantities are temperature compensated to the performance listed in the respective specification. Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 "Typical Performance Curves" for typical performance. N = Value in the AccumulationInternalParameter register (0x005A). The default value of this register is 2 or TCAL = 80 ms for 50 Hz line. 2013 Microchip Technology Inc. DS20005256A-page 3 MCP39F501 TABLE 1-1: ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6 V, TA = -40C to +125C, MCLK = 4 MHz, PGA GAIN = 1. Characteristic Sym. Min. Typ. Max. Units Test Conditions 24-Bit Delta Sigma ADC Performance Analog Input Absolute Voltage VIN -1 -- +1 V Analog Input Leakage Current AIN -- 1 -- nA Differential Input Voltage Range (I1+ - I1-), (V1+ - V1-) -600/GAIN -- +600/GAIN mV VOS -1 -- +1 mV Offset Error Offset Error Drift Gain Error -- 0.5 -- V/C GE -4 -- +4 % -- 1 -- ppm/C ZIN 232 -- -- k 142 -- -- k G=2 72 -- -- k G=4 Gain Error Drift Differential Input Impedance Signal-to-Noise and Distortion Ratio VREF = 1.2V, proportional to VREF SINAD Note 6 G=1 38 -- -- k G=8 36 -- -- k G = 16 33 -- -- k G = 32 92 94.5 -- dB Note 3 Total Harmonic Distortion THD -- -106.5 -103 dBc Note 3 Signal-to-Noise Ratio SNR 92 95 -- dB Note 3 SFDR -- 111 -- dB Note 3 Spurious Free Dynamic Range Crosstalk CTALK -- -122 -- dB AC Power Supply Rejection Ratio AC PSRR -- -73 -- dB AVDD and DVDD = 3.3V + 0.6VPP, 100 Hz, 120 Hz, 1 kHz DC Power Supply Rejection Ratio DC PSRR -- -73 -- dB AVDD and DVDD = 3.0 to 3.6V DC Common Mode Rejection Ratio DC CMRR -- -105 -- dB VCM varies from -1V to +1V bits 10-Bit SAR ADC Performance for Temperature Measurement NR -- 10 -- Absolute Input Voltage VIN DGND - 0.3 -- DGND + 0.3 V Recommended Impedance of Analog Voltage Source RIN -- -- 2.5 k Integral Non-Linearity INL -- 1 2 LSb Resolution Note 1: 2: 3: 4: 5: 6: 7: Specification by design and characterization; not production tested. Calculated from reading the register values. VIN = 1VPP = 353 mVRMS @ 50/60 Hz. Applies to Voltage Sag and Voltage Surge Events Only. Variation applies to internal clock and UART only. All calculated output quantities are temperature compensated to the performance listed in the respective specification. Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 "Typical Performance Curves" for typical performance. N = Value in the AccumulationInternalParameter register (0x005A). The default value of this register is 2 or TCAL = 80 ms for 50 Hz line. DS20005256A-page 4 2013 Microchip Technology Inc. MCP39F501 TABLE 1-1: ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6 V, TA = -40C to +125C, MCLK = 4 MHz, PGA GAIN = 1. Characteristic Sym. Min. Typ. Max. Units Differential Non-Linearity DNL -- 1 1.5 LSb Gain Error GERR -- 1 3 LSb Offset Error EOFF -- 1 2 LSb Temperature Measurement Rate N Test Conditions -- fLINE/2 -- sps Note 7 See Section 3.2 for protocol details Clock and Timings UART Baud Rate UDB -- 4.8 -- kbps Master Clock and Crystal Frequency fMCLK -2% 4 +2% MHz Capacitive Loading on OSCO pin COSC2 -- -- 15 pF When an external clock is used to drive the device Internal Oscillator Tolerance fINT_OSC -- 2 -- % -40 to +85C only (Note 5) VREF -2% 1.2 +2% V TCVREF -- 10 -- ZOUTVREF -- 2 -- k AIDDVREF -- 40 -- A -- -- 10 pF VREF+ AGND + 1.1V -- AGND + 1.1V V AVDD, DVDD 2.7 -- 3.6 V DVDD Start Voltage to Ensure Internal Power-On Reset Signal VPOR DGND -- 0.7 V DVDD Rise Rate to Ensure Internal Power-On Reset Signal SDVDD 0.05 -- -- V/ms AVDD Start Voltage to Ensure Internal Power-On Reset Signal VPOR AGND -- 2.1 V SAVDD 0.042 -- -- V/ms Internal Voltage Reference Internal Voltage Reference Tolerance Temperature Coefficient Output Impedance Current, VREF ppm/C TA = -40C to +85C, VREFEXT = 0 Voltage Reference Input Input Capacitance Absolute Voltage on VREF+ Pin Power Specifications Operating Voltage AVDD Rise Rate to Ensure Internal Power On Reset Signal Note 1: 2: 3: 4: 5: 6: 7: 0 - 3.3V in 0.1s, 0 - 2.5V in 60 ms 0 - 2.4V in 50 ms Specification by design and characterization; not production tested. Calculated from reading the register values. VIN = 1VPP = 353 mVRMS @ 50/60 Hz. Applies to Voltage Sag and Voltage Surge Events Only. Variation applies to internal clock and UART only. All calculated output quantities are temperature compensated to the performance listed in the respective specification. Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 "Typical Performance Curves" for typical performance. N = Value in the AccumulationInternalParameter register (0x005A). The default value of this register is 2 or TCAL = 80 ms for 50 Hz line. 2013 Microchip Technology Inc. DS20005256A-page 5 MCP39F501 TABLE 1-1: ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6 V, TA = -40C to +125C, MCLK = 4 MHz, PGA GAIN = 1. Characteristic Sym. Min. Typ. Max. Units IDD -- 13 -- mA Cell Endurance EPS 100,000 -- -- E/W Self-Timed Write Cycle Time TIWD -- 4 -- ms Number of Total Write/Erase Cycles Before Refresh RREF -- 10,000,000 -- E/W TRETDD 40 -- -- Years IDDPD -- 7 -- mA Operating Current Test Conditions Data EEPROM Memory Characteristic Retention Supply Current during Programming Note 1: 2: 3: 4: 5: 6: 7: Provided no other specifications are violated Specification by design and characterization; not production tested. Calculated from reading the register values. VIN = 1VPP = 353 mVRMS @ 50/60 Hz. Applies to Voltage Sag and Voltage Surge Events Only. Variation applies to internal clock and UART only. All calculated output quantities are temperature compensated to the performance listed in the respective specification. Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 "Typical Performance Curves" for typical performance. N = Value in the AccumulationInternalParameter register (0x005A). The default value of this register is 2 or TCAL = 80 ms for 50 Hz line. TABLE 1-2: SERIAL DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6 V, TA = -40C to +125C, MCLK = 4 MHz Characteristic Sym. Min. Typ. Max. Units VIH 0.8 DVDD -- DVDD V Low-Level Input Voltage VIL VSS -- 0.2 VSSD V High-Level Output Voltage VOH 3 -- -- V IOH = -3.0 mA, VDD = 3.6V VOL -- -- 0.4 V IOL = 4.0 mA, VDD = 3.6V ILI -- -- 1 A -- 0.050 0.100 A High-Level Input Voltage Low-Level Output Voltage Input Leakage Current TABLE 1-3: Test Conditions DIO pins only TEMPERATURE SPECIFICATIONS Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD, DVDD = 2.7 to 3.6V. Parameters Sym. Min. Typ. Max. Units Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C JA -- 35.3 -- C/W Conditions Temperature Ranges Thermal Package Resistances Thermal Resistance, 28LD 5x5 QFN DS20005256A-page 6 2013 Microchip Technology Inc. MCP39F501 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, AVDD = 3.3V, DVDD = 3.3V, TA = +25C, GAIN = 1, VIN = -0.5 dBFS at 60 Hz. Frequency of Occurrence Measurement Error (%) 0.50% 0.40% 0.30% 0.20% 0.10% 0.00% -0.10% -0.20% -0.30% -0.40% -0.50% 0.01 0.1 1 10 100 1000 Current Channel Input Amplitude (mVPEAK) FIGURE 2-1: Active Power, Gain = 1. Total Harmonic Distortion (-dBc) FIGURE 2-4: Total Harominc Distortion (dBc) RMS Current Error (%) 0.100% -107.3 -107.1 -107.0 -106.8 -106.7 -106.5 -106.4 -106.2 -106.1 -105.9 -105.8 0.050% 0.000% -0.050% -0.100% 0.1 FIGURE 2-2: 1 10 100 Input Voltage RMS (mVPP) 1000 RMS Current, Gain = 1. 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 THD Histogram. G=1 G=2 G=4 G=8 G = 16 G = 32 -50 -25 FIGURE 2-5: 0 25 50 75 100 Temperature (C) 125 150 THD vs. Temperature. fIN = -0.5 dBFS @ 60 Hz fD = 3.9 ksps 16384 pt FFT OSR = 256 Dithering = Maximum Amplitude (dB) -40 -60 -80 -100 -120 -140 -160 -180 Frequency of Occurrence 0 -20 -200 0 200 400 600 800 1000 1200 1400 1600 1800 2000 Frequency (Hz) FIGURE 2-3: Spectral Response. 2013 Microchip Technology Inc. 94.2 94.3 94.5 94.6 94.8 94.9 95.1 95.2 95.4 95.5 Signal-to-Noise and Distortion Ratio (dB) FIGURE 2-6: SNR Histogram. DS20005256A-page 7 MCP39F501 Note: Unless otherwise indicated, AVDD = 3.3V, DVDD = 3.3V, TA = +25C, GAIN = 1, VIN = -0.5 dBFS at 60 Hz. Signal-to-Noise and Distortion Ration (dB) 100 90 80 70 60 50 G=1 G=2 G=4 G=8 G = 16 G = 32 40 30 20 10 0 -50 -25 0 25 50 75 100 Temperature (C) FIGURE 2-7: 125 150 SINAD vs. Temperature. 5 4 G=1 Gain Error (%) 3 2 G=2 1 G=4 0 -1 G=8 -2 G = 32 -3 G = 16 -4 -5 -50 -25 0 25 50 75 Temperature (C) Internal Voltage Reference (V) FIGURE 2-8: 100 125 150 Gain Error vs. Temperature. 1.2008 1.2007 1.2006 1.2005 1.2004 1.2003 1.2002 1.2001 1.2000 1.1999 -50 FIGURE 2-9: vs. Temperature. DS20005256A-page 8 0 50 100 Temperature (C) 150 Internal Voltage Reference 2013 Microchip Technology Inc. MCP39F501 3.0 PIN DESCRIPTION The description of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP39F501 5x5 QFN Symbol 1 MODE/DIR 2 NC Function Single or Multiple Device mode with direction control for RS-485 drivers No Connect (must be left floating) 3 NC 4 UART_RX UART Communication RX Pin No Connect (must be left floating) 5 COMMONA Common pin A, to be connected to COMMONB 6 OSCI 7 OSCO Oscillator Crystal Connection Pin 8 NC No Connect (must be left floating) 9 NC No Connect (must be left floating) 10 RESET Reset Pin for Delta Sigma ADCs 11 AVDD Oscillator Crystal Connection Pin or External Clock Input Pin Analog Power Supply Pin 12 UART_TX 13 COMMONB UART Communication TX Pin 14 A0/DIO0 Address Select Pin 0 / Configurable digital I/O 0 15 A1/DIO1 Address Select Pin 1 / Configurable digital I/O 1 16 I1+ Non-Inverting Current Channel Input for 24-bit ADC 17 I1- Inverting Current Channel Input for 24-bit ADC Common pin B, to be connected to COMMONA 18 V1- Inverting Voltage Channel Input for 24-bit ADC 19 V1+ Non-Inverting Voltage Channel Input for 24-bit ADC 20 AN_IN/DIO2 21 AGND 22 DIO3 23 REFIN+/OUT Analog Input for SAR ADC / Configurable Digital Input/Output 2 Pin Analog Ground Pin, Return Path for internal analog circuitry Configurable Digital Input/Output 3 Non-Inverting Voltage Reference Input and Internal Reference Output Pin 24 DGND Digital Ground Pin, Return Path for internal digital circuitry 25 DVDD Power Supply Pin 26 MCLR Master Clear for Device 27 DGND Digital Ground Pin, Return Path for internal digital circuitry 28 DR Data Ready (must be left floating) 29 EP Exposed Thermal Pad (to be connected to DGND) 2013 Microchip Technology Inc. DS20005256A-page 9 MCP39F501 3.1 Single/Multiple Device Mode and Direction Pin (MODE/DIR) When using multiple devices on a single bus, this pin should be tied to the DIR pin of the transceiver for direction control. This will cause the A0/DIO0 and A1/DIO1 pins to act as address pins A0,A1. If additional devices are required, the Device Address register can be programmed to allow for more than four devices. For this operation, a 4.7 k pull-down resistor should be connected to this pin. If only a single device is being used, the MODE pin should be driven high at power-on reset (POR), making the A0/DIO0 and A1/DIO1 pins additional configurable digital I/O (DIO). 3.2 UART Communication Pins (UART_TX, UART_RX) The MCP39F501 device contains an asynchronous full-duplex UART. The UART communication is 8 bits with Start and Stop bit. See Section 4.2 "UART Settings" for more information. 3.3 Common Pins (COMMON A and B) 3.7 Analog Power Supply Pin (AVDD) AVDD is the power supply pin for the analog circuitry within the MCP39F501. This pin requires appropriate bypass capacitors and should be maintained to 2.7V and 3.6V for specified operation. It is recommended to use 0.1 F ceramic capacitors. 3.8 Digital Power Supply Pin (DVDD) DVDD is the power supply pin for the digital circuitry within the MCP39F501. This pin requires appropriate bypass capacitors and should be maintained between 2.7V and 3.6V for specified operation. It is recommended to use 0.1 F ceramic capacitors. 3.9 Configurable Digital Input/Output Pins (DIOn) These digital I/O pins can be configured to act as input or as output events, such as alarm events or interrupt flags, based on the device configuration. For more information, see Section 8.0 "Configurable Digital I/O Pins (DIO Configuration - 0x0046)". The COMMONA and COMMONB pins are internal connections for the MCP39F501. These two pins should be connected together in the application. 3.10 3.4 I1- and I1+ are the two fully-differential current channel inputs for the Delta-Sigma ADCs. Data Ready Pin (DR) The data ready pin indicates if a new delta-sigma A/D conversion result is ready to be processed. This pin is for indication only and should be left floating. After each conversion is finished, a low pulse will take place on the Data Ready pin to indicate the conversion result is ready and an interrupt is generated in the calculation engine (CE). This pulse is synchronous with line frequency and has a predefined and constant width. Note: 3.5 This pin is internally connected to the IRQ of the calculation engine and should be left floating. Oscillator Pins (OSCO/OSCI) OSCO and OSCI provide the master clock for the device. Appropriate load capacitance should be connected to these pins for proper operation. An optional 4 MHz crystal can be connected to these pins. If a crystal of external clock source is not detected, the device will clock from the internal 4 MHz oscillator. 3.6 Reset Pin (RESET) 24-Bit Delta Sigma ADC Differential Current Channel Input Pins (I1+/I1-) The linear and specified region of the channels are dependent on the PGA gain. This region corresponds to a differential voltage range of 600 mVPEAK/GAIN with VREF = 1.2V. The maximum absolute voltage, with respect to AGND, for each In+/- input pin is 1V with no distortion and 6V with no breaking after continuous voltage. 3.11 24-Bit Delta Sigma ADC Differential Voltage Channel Inputs (V1+/V1-) V1- and V1+ are the two fully-differential voltage channel inputs for the Delta-Sigma ADCs. The linear and specified region of the channels are dependent on the PGA gain. This region corresponds to a differential voltage range of 600 mVPEAK/GAIN with VREF = 1.2V. The maximum absolute voltage, with respect to AGND, for each VN+/- input pin is 1V with no distortion and 6V, with no breaking after continuous voltage. This pin is active-low and places the delta-sigma ADCs, PGA, internal VREF and other blocks associated with the analog front-end in a reset state when pulled low. This input is Schmitt-triggered. DS20005256A-page 10 2013 Microchip Technology Inc. MCP39F501 3.12 Analog Input for Temperature Measurement/Configurable Digital Output 2 Pin (AN_IN/DIO2) This is the input to the analog-to-digital converter to be used for temperature measurement. If temperature sensing is required in the application, it is advised to connect the low-power active thermistor ICTM MCP9700A to this pin. 3.13 Analog Ground Pin (AGND) AGND is the ground connection to internal analog circuitry (ADCs, PGA, voltage reference, POR). If an analog ground pin is available on the PCB, it is recommended that this pin be tied to that plane. 3.14 Non-inverting Reference Input/Internal Reference Output Pin (REFIN+/OUT) This pin is the non-inverting side of the differential voltage reference input for the delta sigma ADCs or the internal voltage reference output. For optimal performance, bypass capacitances should be connected between this pin and AGND at all times, even when the internal voltage reference is used. However, these capacitors are not mandatory to ensure proper operation. 3.15 Digital Ground Connection Pins (DGND) DGND is the ground connection to internal digital circuitry (SINC filters, oscillator, serial interface). If a digital ground plane is available, it is recommended to tie this pin to the digital plane of the PCB. This plane should also reference all other digital circuitry in the system. 3.16 Exposed Thermal Pad (EP) This pin is the exposed thermal pad. It must be connected to DGND. 2013 Microchip Technology Inc. DS20005256A-page 11 MCP39F501 NOTES: DS20005256A-page 12 2013 Microchip Technology Inc. MCP39F501 4.0 COMMUNICATION PROTOCOL All communication to the device occurs in frames. Each frame consists of a header byte, the number of bytes in the frame, command packet (or command packets) and a checksum. The communication protocol for the MCP39F501 device is based on the Simple Sensor Interface (SSI) protocol. This protocol is used for point-to-point communication from a single-host MCU to a singleslave MCP39F501. The protocol supports the ability for multiple devices to be on a single bus, but it is only designed to communicate to one device at a time. Note: If a custom communication protocol is desired, please contact a Microchip sales office. Frame Header Byte (0xA5) Number of Bytes Command Packet1 Command Packet2 ...Command Packet n Checksum Command BYTE1 BYTE2 BYTE N BYTE0 BYTE N FIGURE 4-1: MCP39F501 Communication Frame. This approach allows for single, secure transmission from the host processor to the MCP39F501 with either a single command, or multiple commands. No command in a frame is processed until the frame is complete and the checksum and number of bytes are validated. The number of bytes in an individual command packet depends on the specific command. For example, to set the instruction pointer, three bytes are needed in the packet: the command byte and two bytes for the address you want to set to the pointer. The first byte in a command packet is always the command byte. This protocol can also be used to set up transmission from the MCP39F501 on specific registers. A predetermined single-wire transmission frame is defined for one wire interfaces. The Auto-transmit mode can be initiated by setting the SINGLE_WIRE bit in the System Configuration register, allowing for single-wire communication within the application. See Section 4.9 "Single-Wire Transmission Mode" for more information on this communication. 4.1 Checksum The checksum is generated using simple byte addition and taking modulus to find the remainder after dividing the sum of the entire frame by 256. This operation is done to obtain an 8-bit checksum. All the bytes of the frame are included in the checksum, including the header byte and number of bytes. If a frame includes multiple command packets, none of the commands will be issued if the frame checksum fails. In this instance, the MCP39F501 will respond with a CSFAIL response of 0x51. On commands that are requesting data back from the MCP39F501, the frame and checksum are created in the same way, with the header byte becoming an acknowledge (0x06). Communication examples are given in Section 4.6 "Example Communication Frames and MCP39F501 Responses". 4.2 UART Settings The default baud rate is 4.8 kbps. The UART operates in 8-bit mode, plus one start bit and one stop bit, for a total of 10 bits per byte, as shown in Figure 4-1. IDLE START D0 D1 FIGURE 4-1: D2 D3 D4 D5 D6 D7 STOP IDLE UART Transmission, N-8-1. The baud rate is fixed at 4.8 kbps. 2013 Microchip Technology Inc. DS20005256A-page 13 MCP39F501 4.3 Multiple Devices 4.4 In order to support multiple devices on a single bus, a device must be selected before any communication occurs between the host MCU and the individual MCP39F501 devices using the Select Device command. Once selected, the device will assert the DIR pin until it is deselected. Device Address A device is selected by issuing the Select Device command, followed by the appropriate Device Address. The device address is set through the A0, A1 pins and also through the writing of the Device Address register (Location 0x0026), as shown in Figure 4-3. A7 A6 A5 A4 A3 A2 A1 A0 Set through Register Write R UART_RX MODE/DIR FIGURE 4-3: RS-485 BUS 4.7 k UART_TX D FIGURE 4-2: DIR Pin Operation Using Example RS-485 Bus Transceiver. Based on this operation, the sequence of events when communicating to an MCP39F501 on a bus with multiple devices must be as follows: 1. 2. 3. 4. A1, A0 pins Device Address Register. The default address and default register value is 0x4C. If the device is in Multiple Device mode (MODE/DIR = 0 at POR), pins A1 and A0 will override bits 0 and 1 and initial possible addresses include 0x4C, 0x4D, 0x4E and 0x4F depending on the state of these pins. 4.5 Command List The following table is a list of all accepted command bytes for the MCP39F501. Select the device. Communicate to selected device through a communication frame. Repeat Step 2, if necessary. De-select the device. TABLE 4-1: MCP39F501 INSTRUCTION SET Command ID Instruction Parameter Number of Bytes in Command Packet Successful Response UART_TX Register Read, 16 bits 0x52 --------- 1 ACK, Data, CRC Register Read, 32 bits 0x44 --------- 1 ACK, Data, CRC Register Write, 16 bits 0x57 Data 3 ACK Command Register Write, 32 bits 0x45 Data 5 ACK Register Read, N bits 0x4E Number of Bytes 2 ACK, Data, CRC Register Write, N bits 0x4D Number of Bytes 1+N ACK Select Device 0x4C Device Address 2 ACK De-Select Device 0x4B Device Address 2 ACK Set Address Pointer 0x41 ADDRESS 3 ACK Save Registers To Flash 0x53 Device Address 2 ACK Page Read EEPROM 0x42 PAGE 2 ACK, Data, CRC Page Write EEPROM 0x50 PAGE 18 ACK Bulk Erase EEPROM 0x4F Device Address 2 ACK Auto-Calibration Gain 0x5A Device Address Note 1 Auto-Calibration Reactive Gain 0x7A Device Address Note 1 Auto-Calibration Frequency 0x76 Device Address Note 1 Note 1: See Section 9.0, MCP39F501 Calibration for more information on calibration. DS20005256A-page 14 2013 Microchip Technology Inc. MCP39F501 4.6 Example Communication Frames and MCP39F501 Responses TABLE 4-2: FRAME EXAMPLE, SELECT DEVICE COMMAND Transmit Frame 0xA5 Header Byte 0x05 Number of Bytes 0x4C Command (Select Device) 0x4D Device Address 0x42 Checksum TABLE 4-3: Response from MCP39F501 0x06 Acknowledge FRAME EXAMPLE, READ-16 COMMAND Transmit Frame Response from MCP39F501 0xA5 Header Byte 0x06 Acknowledge 0x07 Number of Bytes 0x05 Number of Bytes 0x41 Command (Set Address Pointer) 0x00 Data Byte 0x00 Address0 0x4D Data Byte 0x54 Address1 0x58 Checksum 0x52 Command (Read 16) 0x93 Checksum TABLE 4-4: FRAME EXAMPLE, BULK ERASE EEPROM Transmit Frame 0xA5 Header Byte 0x05 Number of Bytes 0x4F Command (Bulk Erase EE) 0x4D Device Address 0x46 Checksum 2013 Microchip Technology Inc. Response from MCP39F501 0x06 Acknowledge DS20005256A-page 15 MCP39F501 4.7 4.7.1 Command Descriptions REGISTER READ, 16-BIT (0X52) The Register Read, 16-bit command, returns the two bytes that follow whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other read commands. An acknowledge, data and checksum is the response for this command. With this command the data is returned MSB first. 4.7.2 REGISTER WRITE, N BIT (0X4D) The Register Write, N-bit command is followed by N bytes that will be written to whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other write commands. An acknowledge is the response for this command. The maximum number of bytes that can be written with this command is 64. If there are other write commands within a frame, the maximum number of bytes that can be written is 64 minus the number of bytes being written in the frame REGISTER READ, 32-BIT (0X44) The Register Read, 32-bit command, returns the four bytes that follow whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other read commands. An acknowledge, data and checksum is the response for this command. With this command data is returned MSB first. 4.7.3 4.7.6 REGISTER WRITE, 16-BIT (0X57) The Register Write, 16-bit command is followed by bytes that will be written to whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other write commands. An acknowledge is the response for this command. 4.7.7 SELECT DEVICE (0X4C) The Select Device command is used to drive the direction of the bus in Multiple Device mode by asserting the MODE/DIR pin. When the device is in Single Device mode, this command has no effect on the state of the pin. This command is expecting the device address as the command parameter, or the following byte. The device address is a single byte length. If the device address sent with this command matches the value in the MCP39F501's Device Address register, the pin will be asserted and an acknowledge returned. 4.7.8 DE-SELECT DEVICE (0X4B) The Register Write, 32-bit command is followed by four bytes that will be written to whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other write commands. An acknowledge is the response for this command. The Select Device command is used to drive the direction of the bus by deasserting the MODE/DIR pin. When the device is in Single Device mode, this command has no effect on the state of the pin. This command is expecting the Device Address as the command parameter, which is the following byte. The Device Address is a single byte length. If the device address sent with this command matches the value in the MCP39F501's Device Address register, the pin will be deasserted and an acknowledge returned. 4.7.5 4.7.9 4.7.4 REGISTER WRITE, 32-BIT (0X45) REGISTER READ, N BIT (0X4M) The Register Read, N-bit command returns the N bytes that follow whatever the current address pointer is set to. It should typically follow a Set Address Pointer command. It can be used in conjunction with other read commands. An acknowledge, data and checksum is the response for this command. The maximum number of bytes that can be read with this command is 48. If there are other read commands within a frame, the maximum number of bytes that can be read is 48 minus the number of bytes being read in the frame. With this command, the data is returned LSB first. DS20005256A-page 16 SET ADDRESS POINTER (0X41) This command is used to set the address pointer for all read and write commands. This command is expecting the address pointer as the command parameter in the following two bytes. The address pointer is two bytes in length. If the address pointer is within the acceptable addresses of the device, an acknowledge will be returned. 4.7.10 SAVE REGISTERS TO FLASH (0X53) The Save Registers To Flash command makes a copy of all the calibration and configuration registers to flash. This includes all R/W registers in the register set. This command is expecting the device address as the instruction parameter, or the following byte. The device address is a single byte length. If the device address matches, the response to this command is an acknowledge. 2013 Microchip Technology Inc. MCP39F501 4.7.11 PAGE READ EEPROM (0X42) The Read Page EEPROM command returns 16 bytes of data that are stored in an individual page on the MCP39F501. A more complete description of the memory organization of the EEPROM can be found in Section 10.0 "EEPROM". This command is expecting the EEPROM page as the command parameter or the following byte. The response to this command is an acknowledge, 16-bytes of data and CRC checksum. 4.7.12 BULK ERASE EEPROM (0X4F) The Bulk Erase EEPROM command will erase the entire EEPROM array and return it to a state of 0xFFFF for each memory location of EEPROM. A more complete description of the memory organization of the EEPROM can be found in Section 10.0 "EEPROM". This command is expecting the device address as the command parameter for additional security when bulk erasing the EEPROM of a device. 4.7.14 Notation for Register Types The following notation has been adopted for describing the various registers used in the MCP39F501: TABLE 4-5: 4.9 Unsigned, 32-bit register s32 Signed, 32-bit register u16 Unsigned, 16-bit register s16 Signed, 16-bit register b32 32-bit register containing discrete Boolean bit settings Single-Wire Transmission Mode In Single-wire Transmission mode, at the end of each computation cycle, the device automatically transmits a frame of power data. This allows for single-wire communication after the device has been configured. The single-wire transmission frame consists of 16 bytes: three Header Bytes, one Checksum and 12 bytes of power data (including RMS current, RMS voltage, Active Power and Line Frequency). TABLE 4-6: The Auto-Calibration Gain command initiates the single point calibration that is all that is typically required for the system. This command calibrates the RMS current, RMS voltage and active power based on the target values written in the corresponding registers. See Section 9.0 "MCP39F501 Calibration" for more information on device calibration. # 4.7.15 For applications not using an external crystal and running the MCP39F501 off the internal oscillator, a gain calibration to the line frequency indication is required. The Gain Line Frequency (0x00AE) register is set such that the frequency indication matches what is set in the Line Frequency Reference (0x0094) register. See Section 9.0 "MCP39F501 Calibration" for more information on device calibration. SINGLE-WIRE TRANSMISSION FRAME Byte 1 HEADERBYTE (0xAB) 2 HEADERBYTE2 (0xCD) 3 HEADERBYTE3 (0xEF) 4 CURRENT RMS - Byte 0 5 CURRENT RMS - Byte 1 6 CURRENT RMS - Byte 2 7 CURRENT RMS - Byte 3 8 VOLTAGE RMS - Byte 0 9 VOLTAGE RMS - Byte 1 10 ACTIVE POWER - Byte 0 11 ACTIVE POWER - Byte 1 12 ACTIVE POWER - Byte 2 13 ACTIVE POWER - Byte 3 14 LINE FREQUENCY - Byte 0 15 LINE FREQUENCY - Byte 1 16 CHECKSUM Note 1: 2013 Microchip Technology Inc. Description u32 AUTO-CALIBRATION GAIN (0X5A) CALIBRATE FREQUENCY (0X76) SHORT-HAND NOTATION FOR REGISTER TYPES Notation PAGE WRITE EEPROM (0X50) The Write Page EEPROM command is expecting 17 additional bytes in the command parameters, which are EEPROM page plus 16 bytes of data. A more complete description of the memory organization of the EEPROM can be found in Section 10.0 "EEPROM" The response to this command is an acknowledge. 4.7.13 4.8 For custom single-wire transmission packets, contact a Microchip sales office. DS20005256A-page 17 MCP39F501 NOTES: DS20005256A-page 18 2013 Microchip Technology Inc. MCP39F501 5.0 CALCULATION ENGINE (CE) DESCRIPTION 5.1 Computation Cycle Overview The MCP39F501 uses a coherent sampling algorithm to lock the sampling rate to the line frequency, and reports all power output quantities at a 2N number of line cycles. This is defined as a computation cycle and is dependent on the line frequency, so any change in the line frequency will change the update rate of the output power quantities. 5.2 Raw Voltage and Currents Signal Conditioning The first set of signal conditioning that occurs inside the MCP39F501 is shown in Figure 5-1. All conditions set in this diagram effect all of the output registers (RMS current, RMS voltage, active power, reactive power, apparent power, etc.). The gain of the PGA, the shutdown and reset status of the 24-bit ADCs are all controlled through the System Configuration (0X0042) register. For DC applications, offset can be removed by using the DC Offset Current (0x003C) register. To compensate for any external phase error between the current and voltage channels, the Phase Compensation register (0x003E) can be used. I1+ SINC3 Digital Filter See Section 9.0 "MCP39F501 Calibration" for more information on device calibration. 24-bit ADC Multi-level Modulator + PGA I1- CHANNEL I1 SINC3 Digital Filter 24-bit ADC Multi-level Modulator + PGA - + HPF i DCOffsetCurrent:s16 SystemConfiguration:b32 V1+ + V1- HPF v CHANNEL V1 PhaseCompensation:s16 FIGURE 5-1: 5.3 Channel I1 and V1 Signal Flow. RMS Current and RMS Voltage (0x0004, 0x0008) The MCP39F501 device provides true RMS measurements. The MCP39F501 device has two simultaneous sampling 24-bit A/D converters for the current and voltage measurements. The root mean square calculations are performed on 2N current and voltage samples, where N is defined by the register Accumulation Interval Parameter. EQUATION 5-1: RMS CURRENT AND VOLTAGE N N 2 -1 I RMS = 2 -1 in 2 n=0 --------------------------- 2 N V RMS = 2013 Microchip Technology Inc. vn 2 n=0 ---------------------------- 2 N DS20005256A-page 19 MCP39F501 Range:b32 2N-1 i 0 / 2 X N + ACCU X /2RANGE CurrentRMS:u32 + GainCurrentRMS:u16 OffsetCurrentRMS:s32 (Note 1) X ApparentPower:u32 GainVoltageRMS:u16 2N-1 v X 0 / 2 N X ACCU /2RANGE VoltageRMS:u16 Range:b32 Note 1: The value of the Offset Current RMS register is squared internal to the calculation engine, so only the lower 16 bits should be used. The sign of the offset correction is the most significant bit (MSb) of the 32 bit register. FIGURE 5-2: 5.4 RMS Current and Voltage Calculation Signal Flow. Apparent Power (0x0012) 5.5 This 32-bit register is the output register for the final apparent power indication. It is the product of RMS current and RMS voltage as shown in Equation 5-2. EQUATION 5-2: The MCP39F501 has two simultaneous sampling A/D converters. For the active power calculation, the instantaneous current and instantaneous voltages are multiplied together to create instantaneous power. This instantaneous power is then converted to active power by averaging or taking the DC component. APPARENT POWER S = I RMS VRMS Equation 5-4 controls the number of samples used in this accumulation prior to updating the Active Power output register. For scaling of the apparent power indication, the calculation engine uses the register Apparent Power Divisor (0x0040). This is described in the following register operations, per Equation 5-3. EQUATION 5-3: Active Power (0x000A) EQUATION 5-4: ACTIVE POWER 1 P = -----N2 APPARENT POWER CurrentRMS VoltageRMS S = -----------------------------------------------------------------ApparentPowerDivisor 10 N k= 2 -1 Vk Ik k=0 GainActivePower:u16 i Range:b32 2N-1 X 0 / 2 ACCU N + X /2RANGE ActivePower:u32 + v FIGURE 5-3: DS20005256A-page 20 OffsetActivePower:s32 Active Power Calculation Signal Flow. 2013 Microchip Technology Inc. MCP39F501 5.6 Power Factor (0x0016) 5.7 Power factor is calculated by the ratio of P to S or active power divided by apparent power. EQUATION 5-5: Reactive Power (0x000E) In the MCP39F501, Reactive Power is calculated using a 90 degree phase shift in the voltage channel. The same accumulation principles apply as with active power where ACCU acts as the accumulator. Any light load or residual power can be removed by using the Offset Reactive Power (0x0038) register. Gain is corrected by the Gain Reactive Power (0x002E) register. The final output is an unsigned 32-bit value located in the Reactive Power register (0x000E). POWER FACTOR P PF = --S The Power Factor Reading is stored in a signed 16-bit register (Power Factor, 0x0016). This register is a signed, 2's complement register with the MSB representing the polarity of the power factor. Positive means inductive load, negative means capacitive load. Each LSB is then equivalent to a weight of 2-15. A maximum register value of 0x7FFF corresponds to a power factor of 1. The minimum register value of 0x8000 corresponds to a power factor of -1. GainReactivePower:u16 i HPF Range:b32 2N-1 X v FIGURE 5-4: 5.8 0 / 2 ACCU1 + X - /2RANGE ReactivePower:u32 OffsetReactivePower:s32 HPF (+90deg.) Reactive Power Calculation Signal Flow. Accumulation Interval Parameter (0x005A) The accumulation interval is defined as an 2N number of line cycles, where N is the value in the AccumulationIntervalParameter register (0x005A). 5.9 N Thermistor Voltage (0x001A) When a voltage output temperature sensor such as the MCP9700 is connected to the AN_IN/DIO2 pin and the DIO2[n] bits of the DOUT Configuration register are set to 110 for temperature input, the device performs an analog-to-digital conversion on the AN_IN/DIO2 pin. The least 10 significant bits of the 16-bit Thermistor Voltage register contain the output of the ADC. The conversion rate of the temperature measurement occurs once every computation cycle. 2013 Microchip Technology Inc. Note that if the AN_IN/DIO2 pin is configured through the DIO Configuration register (0x0046) as an output, then the Thermistor Voltage register value will equal zero. The Thermistor Voltage is used for temperature compensation of the calculation engine. See Section 9.8 "Temperature Compensation (Addresses 0x00B0/B2/B4/B6)" for more information. MCP9700 FIGURE 5-5: Flow. 10-bit ADC ThermistorVoltage:u16 Thermistor Voltage Signal DS20005256A-page 21 MCP39F501 NOTES: DS20005256A-page 22 2013 Microchip Technology Inc. MCP39F501 6.0 REGISTERS DESCRIPTION 6.1 Register Map The following table describes the registers for the MCP39F501 device. TABLE 6-1: Address MCP39F501 REGISTER MAP Register Name Section Number Read/ Write Data type Description Output Registers 0x0000 Address Pointer 6.2 R u16 Address pointer for read or write commands 0x0002 System Version 6.3 R u16 System version date code information for MCP39F501, set at the Microchip factory; format YMDD 0x0004 Current RMS 5.3 R u32 RMS Current output 0x0008 Voltage RMS 5.3 R u16 RMS Voltage output 0x000A Active Power 5.5 R u32 Active Power output 0x000E Reactive Power 5.7 R u32 Reactive Power output 0x0012 Apparent Power 5.4 R u32 Apparent Power output 0x0016 Power Factor 5.6 R s16 Power Factor output 0x0018 Line Frequency 9.7 R u16 Line Frequency output 0x001A Thermistor Voltage 5.9 R u16 Temperature Monitor output 0x001C Event Flag 7.2 R b16 Status of all enabled events 0x001E System Status 6.4 R b16 System Status Register 0x0020 Reserved -- -- u16 Reserved 0x0022 Reserved -- -- u16 Reserved Calibration Registers 0x0024 Reserved -- -- u16 Reserved 0x0026 Device Address 4.4 R/W u16 Device Address for the device 0x0028 Gain Current RMS 9.3 R/W u16 Gain Calibration Factor for RMS Current 0x002A Gain Voltage RMS 9.3 R/W u16 Gain Calibration Factor for RMS Voltage 0x002C Gain Active Power 9.3 R/W u16 Gain Calibration Factor for Active Power 0x002E Gain Reactive Power 9.3 R/W u16 Gain Calibration Factor for Reactive Power 0x0030 Offset Current RMS 9.6.1 R/W s32 Offset Calibration Factor for RMS Current 0x0034 Offset Active Power 9.6.1 R/W s32 Offset Calibration Factor for Active Power 0x0038 Offset Reactive Power 9.6.1 R/W s32 Offset Calibration Factor for Reactive Power 0x003C DC Offset Current 9.6.2 R/W s16 Offset Calibration Factor for DC Current 0x003E Phase Compensation 9.5 R/W s16 Phase Compensation 0x0040 Apparent Power Divisor 5.4 R/W u16 Number of Digits for apparent power divisor to match IRMS and VRMS resolution Design Configuration Registers 0x0042 System Configuration 6.5 R/W b32 Control for device configuration, including ADC configuration 0x0046 DIO Configuration 8.0 R/W b16 Configurable digital output settings for alarm, and event flags 0x0048 Range 6.6 R/W b32 Scaling factor for Outputs Note 1: These registers are reserved for EMI filter compensation when necessary for power supply monitoring. They may require specific adjustment depending on PSU parameters, please contact the local Microchip office for further support. 2013 Microchip Technology Inc. DS20005256A-page 23 MCP39F501 TABLE 6-1: Address MCP39F501 REGISTER MAP (CONTINUED) Register Name Section Number Read/ Write Data type Description 0x004C Calibration Current 9.3.1 R/W u32 Target Current to be used during single-point calibration 0x0050 Calibration Voltage 9.3.1 R/W u16 Target Voltage to be used during single-point calibration 0x0052 Calibration Active Power 9.3.1 R/W u32 Target Active Power to be used during single-point calibration 0x0056 Calibration Reactive Power 9.5.1 R/W u32 Target Reactive Power to be used during single-point calibration 0x005A Accumulation Interval Parameter 5.8 R/W u16 N for 2N number of line cycles to be used during a single computation cycle 0x005C Reserved -- R/W u16 Reserved Over Current Limit 7.0 R/W u32 RMS Current threshold at which an event flag is recorded 0x0062 Reserved 7.0 R/W u16 Reserved 0x0064 Over Power Limit 7.0 R/W u32 Active Power threshold at which an event flag is recorded 0x0068 Reserved 7.0 R/W u16 Reserved 0x006A Over Frequency Limit 7.0 R/W u16 Line Frequency threshold at which an event flag is recorded 0x006C Under Frequency Limit 7.0 R/W u16 Line Frequency threshold at which an event flag is recorded 0x006E Over Temperature Limit 7.0 R/W u16 Temperature threshold at which an event flag is recorded 0x0070 Under Temperature Limit 7.0 R/W u16 Temperature threshold at which an event flag is recorded 0x0072 Voltage Sag Limit 7.7 R/W u16 RMS Voltage threshold at which an event flag is recorded 0x0074 Voltage Surge Limit 7.7 R/W u16 RMS Voltage threshold at which an event flag is recorded 0x0076 Over Current Hold 7.0 R/W u16 Number of computation cycles for which the Over Current Limit must be breached Event Notification Registers 0x005E 0x0078 Reserved -- R/W u16 Reserved 0x007A Over Power Hold 7.0 R/W u16 Number of computation cycles for which the Over Power Limit must be held 0x007C Reserved -- R/W u16 Reserved 0x007E Over Frequency Hold 7.0 R/W u16 Number of computation cycles for which the Over Frequency Limit must be held 0x0080 Under Frequency Hold 7.0 R/W u16 Number of computation cycles for which the Under Frequency Limit must be held 0x0082 Over Temperature Hold 7.0 R/W u16 Number of computation cycles for which the Over Temperature Limit must be held 0x0084 Under Temperature Hold 7.0 R/W u16 Hold time for which the Under Temperature Limit must be held Reserved -- R/W u16 Reserved 0x0086 Note 1: These registers are reserved for EMI filter compensation when necessary for power supply monitoring. They may require specific adjustment depending on PSU parameters, please contact the local Microchip office for further support. DS20005256A-page 24 2013 Microchip Technology Inc. MCP39F501 TABLE 6-1: Address MCP39F501 REGISTER MAP (CONTINUED) Register Name 0x0088 Reserved Section Number Read/ Write Data type -- R/W u16 Description Reserved 0x008A Event Enable 7.1 R/W u16 Enable Event Register 0x008C Event Mask Critical 7.3 R/W u16 Mask for event notifications to be put on DIO pin selected as "Event Critical" 0x008E Event Mask Standard 7.4 R/W u16 Mask for event notification to be put on DIO pin selected as "Event Standard" 0x0090 Event Test 7.5 R/W u16 Register used to set events for testing purposes 7.6 R/W u16 Register used to clear events 9.7.1 R/W u16 Reference Value for the nominal line frequency 0x0092 Event Clear 0x0094 Line Frequency Ref. 0x0096 Reserved -- R u16 Reserved 0x00AE Gain Line Frequency 9.7 R/W u16 Correction Factor for Line Frequency Indication EMI Filter Compensation Registers (Note 1) 0x0098 Reserved -- R u16 Reserved 0x009A Reserved -- R u16 Reserved 0x009C Reserved -- R u16 Reserved 0x009E Reserved -- R u16 Reserved 0x00A0 Reserved -- R u16 Reserved 0x00A2 Reserved -- R u16 Reserved 0x00A4 Reserved -- R u16 Reserved 0x00A6 Reserved -- R u16 Reserved 0x00A8 Reserved -- R u16 Reserved 0x00AA Reserved -- R u16 Reserved 0x00AC Reserved -- R u16 Reserved TEMPERATURE COMPENSATION REGISTERS 0x00B0 Temperature Compensation for Frequency 9.8 R/W Correction factor for compensating the line frequency indication over temperature 0x00B2 Temperature Compensation for Current 9.8 R/W Correction factor for compensating the Current RMS indication over temperature 0x00B4 Temperature Compensation for Power 9.8 R/W Correction factor for compensating the active power indication over temperature 0x0B6 Ambient Temperature Reference Voltage 9.8 R/W Register for storing the reference temperature during calibration Note 1: These registers are reserved for EMI filter compensation when necessary for power supply monitoring. They may require specific adjustment depending on PSU parameters, please contact the local Microchip office for further support. 2013 Microchip Technology Inc. DS20005256A-page 25 MCP39F501 6.2 Address Pointer (0x0000) 6.4 The System Status register is a read-only register and can be used to detect the various states of pin levels as defined below. This unsigned 16-bit register contains the address to which all read and write instructions occur. This register is only written through the Set Address Pointer command and is otherwise outside the writable range of register addresses. 6.3 System Status (0x001E) System Version (0x0002) The System Version register is hard-coded by Microchip Technology Inc. and contains calculation engine date code information. The System Version register is a date code in the YMDD format, with year and month in hex, day in decimal (e.g. 0xD220 = 2013, Feb. 20th). REGISTER 6-1: SYSTEM STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R-n R-n R-n R-n R-n R-n R-n -- DIO3_S DIO2_S DIO1_S DIO0_S ADDRESS[1] ADDRESS[0] MULTIPLE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 6-3 DIOn_S: State of DIO pin when configured as an input 1 = State of DIO pin is HIGH 0 = State of DIO pin is LOW bit 2-1 ADDRESS[1:0]: State of A1/A0 pins at POR 1 = Pin is logic high 0 = Pin is logic low bit 0 MULTIPLE: Multiple or Single Device mode 1 = State of MODE/DIR pin was LOW at POR (Multiple Device mode) 0 = State of MODE/DIR pin was HIGH at POR (Single Device mode) DS20005256A-page 26 x = Bit is unknown 2013 Microchip Technology Inc. MCP39F501 6.5 6.5.2 System Configuration (0x0042) The System Configuration register contains bits for the following control: * * * * * PGA setting ADC Reset State ADC Shutdown State Voltage Reference Trim Single Wire Auto-transmission 24-bit ADC Reset mode (also called Soft Reset) can only be entered through setting high the RESET<1:0> bits in the System Configuration register. This mode is defined as the condition where the converters are active but their output is forced to `0'. 6.5.3 These options are described in the following sections. 6.5.1 24-BIT ADC RESET MODE (SOFT RESET MODE) PROGRAMMABLE GAIN AMPLIFIERS (PGA) ADC SHUTDOWN MODE ADC Shutdown mode is defined as a state where the converters and their biases are off, consuming only leakage current. When the Shutdown bit is reset to `0', the analog biases will be enabled, as well as the clock and the digital circuitry. The two Programmable Gain Amplifiers (PGAs) reside at the front-end of each 24-bit Delta-Sigma ADC. They have two functions: Each converter can be placed in Shutdown mode independently. This mode is only available through programming of the SHUTDOWN<1:0> bits in the SystemConfiguration register. * Translate the common-mode of the input from AGND to an internal level between AGND and AVDD * Amplify the input differential signal 6.5.4 The PGA block can be used to amplify very low signals, but the differential input range of the delta-sigma modulator must not be exceeded. The PGA is controlled by the PGA_CHn<2:0> bits in Register 6-2 the System Configuration register. Table 6-2 represents the gain settings for the PGAs: TABLE 6-2: PGA CONFIGURATION SETTING (Note 1) Gain PGA_CHn<2:0> Gain (V/V) Gain (dB) 0 VIN Range (V) 0 0 0 1 0 0 1 2 6 0.25 0 1 0 4 12 0.125 0 1 1 8 18 0.0625 1 0 0 16 24 0.03125 1 0 1 32 30 0.015625 Note 1: 0.5 The two undefined settings (110, 111) are G = 1. If desired, the user can calibrate out the temperature drift for ultra-low VREF drift. The internal voltage reference comprises a proprietary circuit and algorithm to compensate first order and second order temperature coefficients. The compensation allows very low temperature coefficients (typically 10 ppm/C) on the entire range of temperatures from -40C to +125C. This temperature coefficient varies from part to part. The temperature coefficient can be adjusted on each part through the System Configuration register (0x0042). The default value of this register is set to 0x42. The typical variation of the temperature coefficient of the internal voltage reference, with respect to VREFCAL register code, is given by Figure 6-1. 60 VREF Drift (ppm) The translation of the common mode does not change the differential signal but recenters the common-mode so that the input signal can be properly amplified. VREF TEMPERATURE COMPENSATION 50 40 30 20 10 0 0 64 128 192 VREFCAL Register Trim Code (decimal) FIGURE 6-1: Trimcode Chart. 2013 Microchip Technology Inc. 256 VREF Tempco vs. VREFCAL DS20005256A-page 27 MCP39F501 REGISTER 6-2: SYSTEM CONFIGURATION REGISTER U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- PGA_CH1[2] PGA_CH1[1] PGA_CH1[0] PGA_CH0[2] PHA_CH0[1] PGA_CH0[0] bit 31 bit 24 R/W-0 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-0 VREFCAL[7] VREFCAL[6] VREFCAL[5] VREFCAL[4] VREFCAL[3] VREFCAL[2] VREFCAL[1] VREFCAL[0] bit 23 bit 16 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 -- -- -- -- -- -- -- SINGLE_WIRE bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 RESET[1] RESET[0] SHUTDOWN[1] SHUTDOWN[0] -- VREFEXT -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 29-27 PGA_CH1 [2:0]: PGA Setting for Channel 1 111 = Reserved (Gain = 1) 110 = Reserved (Gain = 1) 101 = Gain is 32 100 = Gain is 16 011 = Gain is 8 010 = Gain is 4 001 = Gain is 2 000 = Gain is 1 (DEFAULT) bit 26-24 PGA_CH0 [2:0]: PGA Setting for Channel 0 111 = Reserved (Gain = 1) 110 = Reserved (Gain = 1) 101 = Gain is 32 100 = Gain is 16 011 = Gain is 8 010 = Gain is 4 001 = Gain is 2 000 = Gain is 1 (DEFAULT) bit 23-16 VREFCAL[n]: Internal voltage reference temperature coefficient register value (See Section 6.5.4 "VREF Temperature Compensation" for complete description) bit 15-9 Unimplemented: Read as `0` bit 8 SINGLE_WIRE: single wire enable bit 1 = Single Wire transmission is enabled 0 = Single Wire transmission is disabled (DEFAULT) bit 7-6 RESET [1:0]: Reset mode setting for ADCs 11 = Both I1 and V1 are in Reset mode 10 = V1 ADC is in Reset mode 01 = I1 ADC is in Reset mode 00 = Neither ADC is in Reset mode (DEFAULT) bit 5-4 SHUTDOWN [1:0]: Shutdown mode setting for ADCs 11 = Both I1 and V1 are in Shutdown 10 = V1 ADC is in Shutdown 01 = I1 ADC is in Shutdown 00 = Neither ADC is in Shutdown (DEFAULT) bit 2 VREFEXT: Internal Voltage Reference Shutdown Control 1 = Internal Voltage Reference Disabled 0 = Internal Voltage Reference Enabled (DEFAULT) bit 1-0 Unimplemented: Read as `0` DS20005256A-page 28 2013 Microchip Technology Inc. MCP39F501 6.6 Range Register (0x0048) The Range register is a 32-bit register that contains the number of right bit shifts for the following outputs, divided into separate bytes defined below: * RMS Current * RMS Voltage * Power Note that the power range byte operates across both the active and reactive output registers and sets the same scale. . REGISTER 6-3: The purpose of this register is two-fold: the number of right bit shifting (division by 2RANGE) must be high enough to prevent overflow in the output register, and low enough to allow for the desired output resolution. It is the user's responsibility to set this register correctly to ensure proper output operation for a given meter design. For further information and example usage, see Section 9.3 "Single Point Gain Calibrations (Calibrations at Unity Power Factor)". RANGE REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 31 bit 24 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 POWER[7] POWER[6] POWER[5] POWER[4] POWER[3] POWER[2] POWER[1] POWER[0] bit 23 bit 16 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CURRENT[7] CURRENT[6] CURRENT[5] CURRENT[4] CURRENT[3] CURRENT[2] CURRENT[1] CURRENT[0] bit 15 bit 8 R/W-0 VOLTAGE[7] R/W-0 R/W-0 R/W-0 R/W-0 VOLTAGE[6] VOLTAGE[5] VOLTAGE[4] VOLTAGE[3] R/W-0 R/W-0 VOLTAGE[2] VOLTAGE[1] R/W-0 VOLTAGE[0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 32-24 Unimplemented: Read as `0` bit 23-16 POWER[7:0]: Sets the number of right bit shifts for the Active and Reactive Power output registers. bit 15-8 CURRENT[7:0]: Sets the number of right bit shifts for the Current RMS output register. bit 7-0 VOLTAGE[7:0]: Sets the number of right bit shifts for the Voltage RMS output register. 2013 Microchip Technology Inc. DS20005256A-page 29 MCP39F501 NOTES: DS20005256A-page 30 2013 Microchip Technology Inc. MCP39F501 7.0 EVENT NOTIFICATIONS * * * * There are six registers that correspond to the event notifications that can occur when using the MCP39F501: Event Mask Critical Event Mask Standard Event Test Event Clear * Event Enabled * Event Flag BEGIN YES Is the event Masked as Standard ? YES Other Events Flag+Std. ? YES Is the event Flagged or Under Test ? Clear Standard Pin Set Standard Pin Is the event Masked as Critical ? Exit and Process Next Event Exit and Process Next Event Limit Counter ++ Is the Event Hold Time Satisfied ? YES Set Critical Pin YES Clear Event Flag Clear Event Test Clear Event Clear Limit Counter =0 YES YES Is the Over/Under Event Condition True ? YES Clear Critical Pin FIGURE 7-1: Is the event Masked as Standard ? Is the event Masked as Critical ? YES Other Events Flag+Crt. ? Set Event Flag Is the event Cleared or Disabled ? YES Event Order: Over Current Over Power Over Frequency Under Frequency Over Temperature Under Temperature Event Registers Operation Flow Chart. 2013 Microchip Technology Inc. DS20005256A-page 31 MCP39F501 7.1 Event Enable Register (0x008A) The Event Enable register is a read-only register that flags when an event is enabled per the limit and hold registers. : REGISTER 7-1: EVENT ENABLE REGISTER R/W R/W R/W R/W R/W R/W R/W R/W OC OV OP UV OF UF OT UT bit 15 bit 8 R/W R/W U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 OC: Over Current 1 = Fault event is enabled 0 = No Fault bit 14 OV: Over Voltage 1 = Fault event is enabled 0 = No Fault bit 13 OP: Over Power 1 = Fault event is enabled 0 = No Fault bit 12 UV: Under Voltage 1 = Fault event is enabled 0 = No Fault bit 11 OF: Over Frequency 1 = Fault event is enabled 0 = No Fault bit 10 UF: Under Frequency 1 = Fault event is enabled 0 = No Fault bit 9 OT: Over Temperature 1 = Fault event is enabled 0 = No Fault bit 8 UT: Under Temperature 1 = Fault event is enabled 0 = No Fault bit 7 VSA: Voltage Sag 1 = Fault event is enabled 0 = No Fault bit 6 VSU: Voltage Surge 1 = Fault event is enabled 0 = No Fault bit 5-0 Unimplemented: Read as `0` DS20005256A-page 32 x = Bit is unknown 2013 Microchip Technology Inc. MCP39F501 7.2 Event Flag Register (0x001C) The Event Flag register is a read-only register that flags when an event has occurred per the limit and hold registers. : REGISTER 7-2: Note that event flags are latched until the event has passed and the bit has been cleared by the Event Clear register. EVENT FLAG REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 OC OV OP UV OF UF OT UT bit 15 bit 8 R-0 R-0 U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 OC: Over Current 1 = Fault event has occurred 0 = No Fault bit 14 OV: Over Voltage 1 = Fault event has occurred 0 = No Fault bit 13 OP: Over Power 1 = Fault event has occurred 0 = No Fault bit 12 UV: Under Voltage 1 = Fault event has occurred 0 = No Fault bit 11 OF: Over Frequency 1 = Fault event has occurred 0 = No Fault bit 10 UF: Under Frequency 1 = Fault event has occurred 0 = No Fault bit 9 OT: Over Temperature 1 = Fault event has occurred 0 = No Fault bit 8 UT: Under Temperature 1 = Fault event has occurred 0 = No Fault bit 7 VSA: Voltage Sag 1 = Fault event has occurred 0 = No Fault bit 6 VSU: Voltage Surge 1 = Fault event has occurred 0 = No Fault bit 5-0 Unimplemented: Read as `0` 2013 Microchip Technology Inc. x = Bit is unknown DS20005256A-page 33 MCP39F501 7.3 Event Mask Critical Register (0x008C) The Event Mask Critical register is used to mask which events will have an impact on the digital I/O pin that has been designated to the Notification Critical status in the Configurable Digital I/O (DIO) control register. Any number of events can be set here to create activity on the corresponding DIO pin. REGISTER 7-3: EVENT MASK CRITICAL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OC OV OP UV OF UF OT UT bit 15 bit 8 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 OC: Over Current 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 14 OV: Over Voltage 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 13 OP: Over Power 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 12 UV: Under Voltage 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 11 OF: Over Frequency 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 10 UF: Under Frequency 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 9 OT: Over Temperature 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 8 UT: Under Temperature 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 7 VSA: Voltage Sag 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 6 VSU: Voltage Surge 1 = If a fault event occurs, the DIO pin assigned to Notification Critical will be driven high 0 = If a fault event occurs, there is no effect on DIO pin assigned to Notification Critical bit 5-0 Unimplemented: Read as `0` DS20005256A-page 34 2013 Microchip Technology Inc. MCP39F501 7.4 Event Mask Standard Register (0x008E) The Event Mask Standard register is used to mask which events will have an impact on the digital I/O pin that has been designated to the Notification Standard status in the DIO control register. Any number of events can be set here to create activity on the corresponding DIO pin. REGISTER 7-4: EVENT MASK STANDARD REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OC OV OP UV OF UF OT UT bit 15 bit 8 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 OC: Over Current 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 14 OV: Over Voltage 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 13 OP: Over Power 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 12 UV: Under Voltage 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 11 OF: Over Frequency 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 10 UF: Under Frequency 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 9 OT: Over Temperature 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 8 UT: Under Temperature 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 7 VSA: Voltage Sag 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 6 VSU: Voltage Surge 1 = If a fault event occurs, the DIO pin assigned to Notification Standard will be driven high 0 = If a fault event occurs, there is no effect on the DIO pin assigned to Notification Standard bit 5-0 Unimplemented: Read as `0` 2013 Microchip Technology Inc. DS20005256A-page 35 MCP39F501 7.5 Event Test Register (0x0090) The Event Test register is used when the system designer wants to initiate and test event conditions without being able to apply the appropriate currents, voltages, powers, temperature or frequencies that would normally trigger an event notification. Here, when a corresponding bit is set, the MCP39F501 device acts as though the appropriate limit and the hold registers have been breached, and the corresponding event is triggered. These registers should not be used to clear a true event that is triggered from the limit and hold registers, rather the Event Clear register is used for this purpose. : REGISTER 7-5: EVENT TEST REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OC OV OP UV OF UF OT UT bit 15 bit 8 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 OC: Overcurrent 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 14 OV: Overvoltage 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 13 OP: Over Power 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 12 UV: Undervoltage 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 11 OF: Over Frequency 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 10 UF: Under Frequency 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register DS20005256A-page 36 2013 Microchip Technology Inc. MCP39F501 REGISTER 7-5: EVENT TEST REGISTER (CONTINUED) bit 9 OT: Over Temperature 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 8 UT: Under Temperature 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 7 VSA: Voltage Sag 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 6 VSU: Voltage Surge 1 = Triggers an event and the corresponding event flag bits and Critical/Standard pins will follow per the mask registers 0 = Clears any event set using the event test register. Writing a zero here has no effect on true events, for clearing true events use the event clear register bit 5-0 Unimplemented: Read as `0` 7.6 Event Clear Register (0x0092) The Event Test register is used to clear an event that has been triggered by either real conditions that have breached the corresponding limit and hold registers for a given event, or an event that has been triggered by setting the corresponding bit in the Event Test register. By clearing an event using the EventClear register, if the corresponding event has been set using the Event Test register, this bit, along with the Event Flag register, will be automatically cleared. REGISTER 7-6: The Event Clear register bits are not latched, and once set, will be automatically cleared after the Event Flag and Event Test registers have been cleared. EVENT CLEAR REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OC OV OP UV OF UF OT UT bit 15 bit 8 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 VSA VSU -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 x = Bit is unknown OC: Overcurrent 1 = Clears the event 0 = No effect 2013 Microchip Technology Inc. DS20005256A-page 37 MCP39F501 REGISTER 7-6: EVENT CLEAR REGISTER (CONTINUED) bit 14 OV: Overvoltage 1 = Clears the event 0 = No effect bit 13 OP: Over Power 1 = Clears the event 0 = No effect bit 12 UV: Undervoltage 1 = Clears the event 0 = No effect bit 11 OF: Over Frequency 1 = Clears the event 0 = No effect bit 10 UF: Under Frequency 1 = Clears the event 0 = No effect bit 9 OT: Over Temperature 1 = Clears the event 0 = No effect bit 8 UT: Under Temperature 1 = Clears the event 0 = No effect bit 7 VSA: Voltage Sag 1 = Clears the event 0 = No effect bit 6 VSU: Voltage Surge 1 = Clears the event 0 = No effect bit 5-0 Unimplemented: Read as `0` 7.7 Voltage Sag and Voltage Surge Detection The event alarms for Voltage Sag and Voltage Surge work differently compared to the other event alarms, which are tested against every computation cycle. These two event alarms are designed to provide a much faster interrupt if the condition occurs. Note that neither of these two events have a respective Hold register associated with them, since the detection time is less than one line cycle. The calculation engine keeps track of a trailing mean square of the input voltage, as defined by the following equation: Therefore, at each data ready occurrence, the value of VSA is compared to the programmable threshold set in the Voltage Sag Limit register (0x0086) and Voltage Surge Limit register (0x0088) to determine if a flag should be set. If either of these events are masked to either the standard or critical event pin, a logic-high interrupt will be given on these pins. These events, like all the other events, are latched, and must be cleared after the event has passed by using the appropriate clear event bit. The sag or surge events can be used to quickly determine if a power failure has occurred in the system. Using the on-chip EEPROM of the MCP39F501, these events can be quickly logged to memory to keep track of damaging events for the PSU. EQUATION 7-1: 2 f LINE V SA = -------------------------- f SAMPLE DS20005256A-page 38 0 2 Vn f SAMPLE n = - -------------------------- - 1 2 f LINE 2013 Microchip Technology Inc. MCP39F501 8.0 CONFIGURABLE DIGITAL I/O PINS (DIO CONFIGURATION - 0X0046) 8.1 8.1.3 There are two digital IO pins that are multiplexed with the address pins for a multi-device bus. DIO0 is also A0 and DIO1 is also A1. For systems with multiple devices on a single bus, the MODE/DIR pin should have a weak pull-down resistor to GND, as seen in Figure 4-2. At POR, the MCP39F501 tests the state of this pin, and if the MODE/DIR is logic low, then the DIO0 and DIO1 are disabled and these pins become input pins for the A0 and A1 bits of the Device Address device address, the beginning of the calibration register block. If the MODE/DIR pin is logic high, then the device is considered to be in Single Device mode, the address pins are not needed, and DIO0 and DIO1 can then be configured as any of the seven possible configurations. Overview The MCP39F501 device has four pins that can be configured in five possible configurations. These configurations are: * * * * * Notification Standard Output Notification Critical Output Logic Input Device Address Bit Input (DIO0/DIO1 only) Temperature Input (DIO2 only) 8.1.1 NOTIFICATION OUTPUTS (STANDARD AND CRITICAL) 8.1.4 TEMPERATURE INPUT (DIO2 ONLY) When DIO2 is configured as a temperature input, the Thermistor Voltage register (0x001A) contains the scaled value of the ADC reading from an attached temperature sensor. When a pin is defined to be a notification for either a standard or critical event, the associated pin will become active based on the masks set through the event registers (see Section 7.0 "Event Notifications"). 8.1.2 DEVICE ADDRESS BIT INPUT (A0/DIO0, A1/DIO1 ONLY) If DIO2 is configured as an output, the value in the Thermistor Voltage register will be equal to zero. LOGIC INPUTS The default assignment for all DIO pins are logic input. In this assignment, the state of the DIO pin is reflected in the SystemStatus register, and can be used to flag for various system events and read through the serial interface. REGISTER 8-1: DIO CONFIGURATION REGISTER U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- -- DIO3[2] DIO3[1] DIO[0] DIO2[2] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DIO2[1] DIO2[0] DIO1[2] DIO1[1] DIO1[0] DIO0[2] DIO0[1] DIO0[0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-12 Unimplemented: Read as `0` bit 11-9 DIO3[n]: DIO3 Configuration 111 = Not Used 110 = Not Used 101 = Notification Standard Output 100 = Notification Critical Output 011 = Not Used 010 = Input (Default) 001 = Not Used 000 = Not Used 2013 Microchip Technology Inc. x = Bit is unknown DS20005256A-page 39 MCP39F501 REGISTER 8-1: DIO CONFIGURATION REGISTER (CONTINUED) bit 8-6 DIO2[n]: DIO2 Configuration 111 = Not Used 110 = Not Used 101 = Notification Standard Output 100 = Notification Critical Output 011 = Temperature Input 010 = Input (Default) 001 = Not Used 000 = Not Used bit 5-3 DIO1[n]: DIO1 Configuration 111 = Not Used 110 = Not Used 101 = Notification Standard Output 100 = Notification Critical Output 011 = Device Address Bit Input 010 = Input (Default) 001 = Not Used 000 = Not Used bit 2-0 DIO0[n]: DIO0 Configuration 111 = Not Used 110 = Not Used 101 = Notification Standard Output 100 = Notification Critical Output 011 = Device Address Bit Input 010 = Input (Default) 001 = Not Used 000 = Not Used DS20005256A-page 40 2013 Microchip Technology Inc. MCP39F501 9.0 MCP39F501 CALIBRATION 9.3.1 9.1 Overview By applying stable reference voltages and currents that are equivalent to the values that reside in the target Calibration Current (0x004C), Calibration Voltage (0x0050) and Calibration Active Power (0x0052) registers, the Auto-Calibration Gain command can then be issued to the device. Calibration compensates for ADC gain error, component tolerances and overall noise in the system. The device provides an on-chip calibration algorithm that allows simple system calibration to be performed quickly. The excellent analog performance of the A/D converters on the MCP39F501 allows for a single point calibration and a single calibration command to achieve accurate measurements. Calibration can be done by either using the predefined auto-calibration commands, or by writing directly to the calibration registers. If additional calibration points are required (AC offset, Phase Compensation, DC offset), the corresponding calibration registers are available to the user and will be described separately in this section. 9.2 Calibration Order The proper steps for calibration need to be maintained. If the device has an external temperature sensor attached, temperature calibration should be done first by reading the value from the Thermistor Voltage register (0x001A) and copying the value by writing to the Ambient Temperature Reference Voltage register (0x00B6). If the device runs on the internal oscillator, the line frequency must be calibrated next using the AutoCalibration Frequency command. The single point gain calibration at unity power factor should be performed next. If non-unity displacement power factor measurements are a concern, then the next step should be phase calibration, followed by reactive power gain calibration. To summarize the order of calibration: 1. 2. 3. 4. 5. 9.3 Temperature Calibration (optional) Line Frequency Calibration (optional) Gain Calibration at PF = 1 Phase Calibration at PF 1 (optional) Reactive Gain Calibration at PF 1(optional) Single Point Gain Calibrations (Calibrations at Unity Power Factor) When using the device in AC mode with the high-pass filters turned on, most offset errors are removed and only a single point gain calibration is required. Setting the gain registers to properly produce the desired outputs can be done manually by writing to the appropriate register. The alternative method is to use the auto-calibration commands described in this section. 2013 Microchip Technology Inc. USING THE Auto-Calibration Gain COMMAND After a successful calibration (response = ACK), a Save Registers to Flash command can then be issued to save the calibration constants calculated by the device. The following registers are set when the Auto-Calibration Gain command is issued: * Gain Current RMS (0x0028) * Gain Voltage RMS (0x002A) * Gain Active Power (0x002C) When this command is issued, the MCP39F501 attempts to match the expected values to the measured values for all three output quantities by changing the gain register based on the following formula: EQUATION 9-1: Expected GAIN NEW = GAIN OLD -------------------------Measured The same formula applies for voltage RMS, current RMS and active power. Since the gain registers for all three quantities are 16-bit numbers, the ratio of the expected value to the measured value (which can be modified by changing the Range register) and the previous gain must be such that the equation yields a valid number. Here the limits are set to be from 25,000 to 65,535. A new gain within this range for all three limits will return an ACK for a successful calibration, otherwise the command returns a NAK for a failed calibration attempt. It is the user's responsibility to ensure that the proper range settings, PGA settings and hardware design settings are correct to allow for successful calibration using this command. 9.3.2 EXAMPLE OF RANGE SELECTION FOR VALID CALIBRATION In this example, a user applies a calibration current of 1A to an uncalibrated system. The indicated value in the Current RMS register (0x0004) is 2300 with the system's specific shunt value, PGA gain, etc. The user expects to see a value of 1000 in the Current RMS register when 1A current is applied, meaning 1.000 A with 1 mA resolution. Other given values are: * The existing value for Gain Current RMS is 33480. * The existing value for Range is 12. DS20005256A-page 41 MCP39F501 By using Equation 9-1, the calculation for GainNEW yields: EQUATION 9-2: Expected 1000 GAIN NEW = GAIN OLD --------------------------- = 33480 ------------ = 14556 Measured 2300 14556 20000 When using the Auto-Calibration Gain command, the result would be a failed calibration or a NAK returned form the MCP39F501, because the resulting GainNEW is less than 20,000. The solution is to use the Range register to bring the measured value closer to the expected value, such that a new gain value can be calculated within the limits specified above. The GainNEW is much larger than the 16-bit limit of 65535, so fewer right-bit shifts must be introduced to get the measured value closer to the expected value. The user needs to compute the number of bit shifts that will give a value lower than 65535. To estimate this number: EQUATION 9-5: 145565 ------------------ = 2.2 65535 2.2 rounds to the closest integer value of 2. The range value changes to 12 - 2 = 10; there are 2 less right-bit shifts. The new measured value will be 2300 x 22 = 9200. The Range register specifies the number of right-bit shifts (equivalent to divisions by 2) after the multiplication with the Gain Current RMS register. Refer to Section 5.0 "Calculation Engine (CE) Description" for information on the Range register. EQUATION 9-6: Incrementing the Range register by 1 unit, an additional right-bit shift or /2 is included in the calculation. Increasing the current range from 12 to 13 yields the new measured Current RMS register value of 2300/2 = 1150. The expected (1000) and measured (1150) are much closer now, so the expected new gain should be within the limits: The resulting new gain is within the limits and the device successfully calibrates Current RMS and returns an ACK. EQUATION 9-3: Expected 1000 GAIN NEW = GAIN OLD --------------------------- = 33480 ------------ = 29113 Measured 1150 20000 29113 65535 The resulting new gain is within the limits and the device successfully calibrates Current RMS and returns an ACK. It can be observed that the range can be set to 14 and the resulting new gain will still be within limits (GainNEW = 58226). However, since this gain value is close to the limit of the 16-bit Gain register, variations from system to system (component tolerances, etc.) might create a scenario where the calibration is not successful on some units and there would be a yield issue. The best approach is to choose a range value that places the new gain in the middle of the bounds of the gain registers described above. Expected 10000 GAIN NEW = GAIN OLD --------------------------- = 33480 --------------- = 36391 Measured 9200 20000 36391 65535 9.4 Calibrating the Phase Compensation Register (0x003E) Phase compensation is provided to adjust for any phase delay between the current and voltage path. This procedure requires sinusoidal current and voltage waveforms, with a significant phase shift between them, and significant amplitudes. The recommended displacement power factor for calibration is 0.5. The procedure for calculating the phase compensation register is the following: 1. Determine what is the difference between the angle corresponding to the measured power factor (PFMEAS) and the angle corresponding to the expected power factor (PFEXP), in degrees. EQUATION 9-7: Value in PowerFactor Register PF MEAS = --------------------------------------------------------------------------32768 180 ANGLEMEAS = acos PFMEAS --------- 180 ANGLE EXP = acos PF EXP --------- In a second example, when applying 1A, the user expects an output of 1.0000A with 0.1 mA resolution. The example is starting with the same initial values: 2. EQUATION 9-4: EQUATION 9-8: Expected 1000 GAIN NEW = GAIN OLD --------------------------- = 33480 ------------ = 145565 Measured 2300 Convert this from degrees to the resolution provided by the Equation 9-8: = ANGLE MEAS - ANGLE EXP 40 145565 65535 DS20005256A-page 42 2013 Microchip Technology Inc. MCP39F501 3. Combine this additional phase compensation to whatever value is currently in the phase compensation, and update the register. Equation 9-9 should be computed in terms of a 8-bit 2's complement signed value. The 8-bit result is placed in the least significant byte of the 16-bit Phase Compensation register (0x003E). EQUATION 9-9: PhaseCompensation NEW = PhaseCompensation OLD + Based on Equation 9-9, the maximum angle in degrees that can be compensated is 3.2 degrees. If a larger phase shift is required, contact your local Microchip sales office. 9.5 Reactive Power Calibration and Phase Compensation (Calibrations at Non-unity Power Factor) In order to correctly calibrate the reactive power calculation through the Gain Reactive Power register (0x002E), and to properly correct for any phase error through the Phase Compensation register, the calibration must be done at a power factor other than PF = 1, typically at PF = 0.5. 9.5.1 USING THE AUTO-CALIBRATION REACTIVE GAIN COMMAND By applying the equivalent current, voltage and phase lag (or lead) that correspond to the target reactive power in the Calibration Reactive Power register (0x0056), the Auto-Calibration Gain command (0x7A) can be issued to the device. After a successful calibration (response = ACK), a Save Registers to Flash command can then be issued to save the calibration constants calculated by the device. The following register is set when the Auto-Calibration Gain command is issued: * Gain Reactive Power When this command is issued, the MCP39F501 attempts to match the expected value of the reactive power to the measured value of reactive power by changing the GainReactivePower register. 9.6 Offset/No Load Calibrations During offset calibrations, no line voltage or current should be applied to the system. The system should be in a No Load condition. 2013 Microchip Technology Inc. 9.6.1 AC OFFSET CALIBRATION There are three registers associated with the AC Offset Calibration: * Offset Current RMS(0x0030) * Offset Active Power(0x0034) * Offset Reactive Power(0x0038) When computing the AC offset values, the respective gain and Range registers should be taken into consideration according to the block diagrams in Figures 5-2, 5-3 and 5-4. After a successful offset calibration, a Save Registers to Flash command can then be issued to save the calibration constants calculated by the device. 9.6.2 DC OFFSET CALIBRATION In DC applications, the high-pass filter on the current and voltage channels is turned off. To remove any residual DC value on the current, the DCOffsetCurrent (0x003C) register adds to the A/D conversion immediately after the ADC and prior to any other function. 9.7 Calibrating the Line Frequency Register (0x0018) The Line Frequency register contains a 16-bit number with a value equivalent to the input line frequency as it is measured on the voltage channel. When in DC mode, this calculation is turned off and the register will be equal to zero. The measurement of the line frequency is only valid from 45 to 65 Hz. 9.7.1 USING THE Auto-Calibration Frequency COMMAND By a applying stable reference voltage with a constant line frequency that is equivalent to the value that reside in the Line Frequency Ref (0x0094), the Auto-Calibration Frequency command can then be issued to the device. After a successful calibration (response = ACK), a Save Registers to Flash command can then be issued to save the calibration constants calculated by the device. The following register is set when the Auto-Calibration Frequency command is issued: * Gain Line Frequency (0x00AE) Note that the command is only required when running off the internal oscillator. The formula used to calculate the new gain is given in Equation 9-1. DS20005256A-page 43 MCP39F501 9.8 Temperature Compensation (Addresses 0x00B0/B2/B4/B6) MCP39F501 measures the indication of the temperature sensor and uses the value to compensate the temperature variation of the shunt resistance and the frequency of the internal RC oscillator. The same formula applies for Line Frequency, Current RMS, Active Power and Reactive Power. The temperature compensation coefficient depends on the 16-bit signed integer value of the corresponding compensation register. EQUATION 9-10: y = x 1 + c T - T CAL TemperatureCompensation Register c = ----------------------------------------------------------------------------------------------M 2 Where: x = Uncompensated Output (corresponding to Line Frequency, Current RMS, Active Power and Reactive Power) y = Compensated Output c = Temperature Compensation Coefficient (depending on the shunt's Temperature Coefficient of Resistance or on the internal RC oscillator temperature frequency drift) T = Thermistor Voltage (in 10-bit ADC units) TCAL = Ambient Temperature Reference Voltage. It should be set at the beginning of the calibration procedure, by reading the thermistor voltage and writing its value to the ambient temperature reference voltage register. M = 26 (for Line Frequency compensation) = 27 (for Current, Active Power and Reactive Power) At the calibration temperature, the effect of the compensation coefficients is minimal. The coefficients need to be tuned when the difference between the calibration temperature and the device temperature is significant. It is recommended to use the default values as starting points. DS20005256A-page 44 2013 Microchip Technology Inc. MCP39F501 10.0 EEPROM There are three commands that support access to the EEPROM array. The data EEPROM is organized as 16-bit wide memory. Each word is directly addressable, and is readable and writable across the entire VDD range. The MCP39F501 has 256 16-bit words of EEPROM that is organized in 32 pages for a total of 512 bytes. TABLE 10-1: * EEPROM Page Read (0x42) * EEPROM Page Write (0x50) * EEPROM Bulk Erase (0x4F) EXAMPLE EEPROM COMMANDS AND DEVICE RESPONSE Command Command ID BYTE 0 BYTE 1-N # Bytes Successful Response Page Read EEPROM 0x42 PAGE 2 ACK, Data, CRC Page Write EEPROM 0x50 PAGE + 16 BYTES OF DATA 18 ACK Bulk Erase EEPROM 0x4F --------- 1 ACK TABLE 10-2: Page MCP39F501 EEPROM ORGANIZATION 00 02 04 06 08 0A 0C 0E 0 0000 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 1 0010 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 2 0020 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 3 0030 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 4 0040 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 5 0050 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 6 0060 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 7 0070 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 8 0080 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 9 0090 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 10 00A0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 11 00B0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 12 00C0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 13 00D0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 14 00E0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 15 00F0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 16 0100 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 17 0110 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 18 0120 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 19 0130 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 20 0140 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 21 0150 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 22 0160 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 23 0170 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 24 0180 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 25 0190 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 26 01A0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 27 01B0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 28 01C0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 29 01D0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 30 01E0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 31 01F0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 2013 Microchip Technology Inc. DS20005256A-page 45 MCP39F501 NOTES: DS20005256A-page 46 2013 Microchip Technology Inc. MCP39F501 11.0 PACKAGING INFORMATION 11.1 Package Marking Information 28-Lead QFN (5x5x0.9 mm) PIN 1 Example PIN 1 39F501 e3 E/MQ ^^ 1340256 Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2013 Microchip Technology Inc. DS20005256A-page 47 MCP39F501 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005256A-page 48 2013 Microchip Technology Inc. MCP39F501 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2013 Microchip Technology Inc. DS20005256A-page 49 MCP39F501 28-Lead Plastic Quad Flat, No Lead Package (MQ) - 5x5 mm Body [QFN] Land Pattern With 0.55 mm Contact Length Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Microchip Technology Drawing C04-2140A DS20005256A-page 50 2013 Microchip Technology Inc. MCP39F501 APPENDIX A: REVISION HISTORY Revision A (December 2013) * Original Release of this Document. 2013 Microchip Technology Inc. DS20005256A-page 51 MCP39F501 NOTES: DS20005256A-page 52 2013 Microchip Technology Inc. MCP39F501 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device [X](1) X Tape and Temperature Reel Range Device: /XX Package MCP39F501: Single Phase Energy and Power Monitoring IC with Calculation Examples: a) MCP39F501-E/MQ: b) MCP39F501T-E/MQ: Tape and Reel, Extended Temperature, 28LD 5x5 QFN package. Note 1: Tape and Reel Option: Blank = Standard packaging (tube or tray) T = Tape and Reel(1) Temperature Range: E = -40C to +125C Package: MQ = Plastic Quad Flat, No Lead Package - 5x5x0.9 mm Body (QFN) 2013 Microchip Technology Inc. Extended Temperature, 28LD 5x5 QFN package. Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip sales office for package availability for the Tape and Reel option. DS20005256A-page 53 MCP39F501 NOTES: 2013 Microchip Technology Inc. DS20005256A-page 54 Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620777787 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2013 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS20005256A-page 55 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS20005256A-page 56 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 08/20/13 2013 Microchip Technology Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: MCP39F501T-E/MQ MCP39F501-E/MQ