POWER
NTS350 Series
350 Watts
Total Power: 200 - 350 Watts
Input Voltage: 85 - 264 Vac
120 - 300 Vdc
# of Outputs: Single
SPECIAL FEATURES
Active power factor correction
IEC EN6100-3-2 compliance
Remote sense
Power fail and remote inhibit
Single wire current sharing
Built-in EMI lter
Low output ripple
5 V standby
12 V fan output
Overvoltage protection
Overload protection
Thermal overload protection
DC power good
Built in OR-ing diode/FET
Optional fan cover (-CF sufx)
Optional end fan cover (-CEF sufx)
SAFETY
TUV 60950
UL 0950
CSA 60950
cULus 60950 (-CEF)
NEMKO 60950
AUSTEL 60950
CB Certicate and report
CE Mark (LVD)
CCC Certicate
Electrical Specications
Input
Input ra nge: 85 - 264 Vac (wide range)
Frequency: 47 - 440 Hz (47- 63 Hz for -CEF versions)
Inrush current: 38 A max., cold start @ 25 °C
Efciency: 85% typical at full load
EMI lter:
FCC Class B conducted and radiated; CISPR22 Class B conducted
and radiated; EN55022 Class B conducted and radiated;
VDE0878PT3 Class B conducted and radiated.
Safety ground leakage
current:
< 0.5 mA @ 50/60 Hz, 264 Vac input
Output
Maximum power: 200 W for convection; 350 W with 30CFM forced air
Adjustment range: ± 5%
Standby output: 5 V @ 2 A regulated, ± 5%
Fan output: 12 V @ 1 A, -5 %, +7%, 0.5 A for -CF version
Hold-up time: 20 ms @ 350 W load, 115 Vac nominal line at factory voltage setting
Overload protection: Short circuit protection on all outputs. Case overload protected @
115 - 130% of peak rating
Overvoltage protection: 20 - 35% above nominal output
Data Sheet
LPS100-M Series Data SheetNTS350 Series Data Sheet
Logic Control
Power failure
TTL logic signal goes high 100 - 500 msec after main output. It goes low at least 4 msec before loss of regulation
Remote on/off Requires an external contact closure to inhibit outputs
DC OK TTL logic goes high after the output is in regulation. It goes low when there is loss of regulation.
Remote sense
Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected.
Ordering Information
Model Number Output Voltage Minimum Load
Maximum Load
with Convection
Cooling
Maximum Load
with 30CFM
Forced Air
Peak Load1Regulation2Ripple
P/P (PARD)3
NTS353 12 V 0 A 16.6 A 29.2 A 33 A ± 2% 120 mV
NTS355 24 V 0 A 8.3 A 14.6 A 16.5 A ± 2% 240 mV
NTS358 48 V 0 A 4.2 A 7.3 A 8.2 A ± 2% 480 mV
NTS359 54 V 0 A 3.7 A 6.5 A 7.4 A ± 2% 540 mV
1. Peak current lasting < 30 seconds with a maximum 10% duty cycle.
2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3 . Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4 . CF sufx added to the model number indicates cover with top fan. -CEF sufx added to the model number indicates cover with end mounted
fan cover and AC inlet
5.
This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated
as a standalone product. EMC compliance to appropriate standards must be veried at the system level. This product is for sale to OEMs and
System Integrators, including through Distribution Channels. It is not intended for sale to End Users.
Environmental Specications
Operating temperature: 0° to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C.
Storage temperature: -40 °C to +85 °C
Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity: Operating; non-condensing 10% to 90% RH
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances. 2 G peak 8 Hz to 500 Hz, operational
MTBF demonstrated: 1M hours at full load and 25 °C ambient conditions
LPS100-M Series Data SheetNTS350 Series Data Sheet
Pin Assignments
Connector
SK1 PIN 1 Line
PIN 3 Neutral
PIN 5 Ground
SK5
PIN 1 V1 swp
PIN 2 - Remote Sense
PIN 3 + Remote Sense
PIN 4 5VSB (standby)
PIN 5 5VSB return
PIN 6 +12V
PIN 7 Common
PIN 8 Inhibit
PIN 9 DC power good (DC OK)
PIN 10 Power Fail (POK)
Adjustment Potentiometers
P1 +V1 Output adjust
P3 +5VSB adjust
Mating Connectors
SK1 AC input Molex 09-50-8051 (USA)
Molex 09-91-0500 (UK)
PINS:08-52-0113
SK2,3,4 Molex BB-124-08
SK5 Control signals Molex 90142-0010
PINS: 90119-2110
Or Amp: 87977-3
PINS: 87309-8
Artesyn Embedded Technologies Connector Kit #70-841-022 includes all of the above
1. Specications subject to change without
2. All dimensions in inches (mm), tolerance is ± 0.2”.
3.Specications are at factory settings
4. Mounting maximum insertion depth is 0.12”.
5.Warranty: 2 year
6.Weight: NTS35X 1.65 lbs/750g. NTS35X-CF 2 lbs/909g. NTS35X-CEF 2.25 lbs/1022g.
15
610
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc.
All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal.
www.artesyn.com
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
NTS350 Series Data Sheet
NTS350 DS 21Mar2016
a
b
ab
ab
ab
ab
ab
ab
a
b
9.15"
(232.3)
AIR FLOW DIRECTION
4.0"
(101.6)
1.61"
(40.9)
1.255"
(31.9)
0.862"
(21.9)
2.40"
(61) 6.244"
(158.6)
5.85"
(148.6)
0.862"
(21.9)
6.437"
(63.5)
0.752"
(19.1)
2.9"
(73.6)
4.7"
(119.6) 5.5"
(139.7)
M3 (8 places)
#6-32 (8 places)
Mechanical Drawing - CEF option
NTS350 Series Data Sheet
Mechanical Drawing
4.0 (101.6)
7.0 (177.8)
(2X)4.7 (119.6)
1.5 (38.10)
(2X)6.4
(3X).75 (19.1)
1.14 (29.1)
(4X)
2.5 (63.5)
(2X)5.5 (139.7)
5.85 (148.7)
6.25 (158.7)
(SEE NOTE 5)
-CF option
SK1
531
+ V OR-ing out
-CF option
+ V out
Common
P1
P3
P1
P3
#6-32 (8 places)
M3 (8 places)
a
a
a
abb
bb
a
bab
1.27 (32.26)
(Must be used in parallel operation)
(Do not use in parallel operation)
1
5
6
10
P1
Voltage
ADJ POT
