Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Features * RF Bandwidth: 1025-1150, 2050-2300, 4100-4600 MHz * 24-bit Step Size, Resolution 3 Hz typ * Ultra Low Phase Noise -112 dBc/Hz in Band Typ. * Built in Digital Self Test * Figure of Merit (FOM) -230 dBc/Hz * Exact Frequency Mode * 40 Lead 6x6 mm SMT Package: 36 mm2 * <180 fs RMS Jitter Typical Applications PLLS WITH INTEGRATED VCO - SMT 7 7-1 * Cellular/4G Infrastructure * Phased Array Applications * Repeaters and Femtocells * DDS Replacement * Communications Test Equipment * Very High Data Rate Radios * CATV Equipment Functional Diagram For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz General Description The HMC837LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with a triband output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. Electrical Specifications VPPCP, VDDCP, VCC1, VCC2 = 5V; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V GNDCP = GNDLS = Ground Paddle = 0V, Min and Max Specified across Temp Parameter Condition Min. Typ. Max. Units RF Output Characteristics VCO Frequency at PLL Input 2050 2300 MHz RF Output Frequency at f VCO/2 1025 1150 MHz RF Output Frequency at f VCO 2050 2300 MHz RF Output Frequency at 2f VCO 4100 4600 MHz Output Power RF Output Power at f VCO/2 RF Output Power at f VCO matched at the frequency of interest, vs temperature RF Output Power at 2f VCO 11 12 13 dBm 9 10.5 12 dBm -3 -0.5 2 dBm 9.7 12.4 16.5 MHz/V VCO Tuning Sensitivity Measured at fo, 2V VCO Supply Pushing Measured at fo, 2V 1 MHz/V RF Output Fout/2 Harmonic Doubler Mode -26 dBc RF Output 3 Fout/2 Harmonic Doubler Mode -47 dBc Harmonics RF Output 2nd Harmonic RF Output 5 Fout/2 Harmonic RF Output 3rd Harmonic RF Output 7 Fout/2 Harmonic RF Output 4th Harmonic fo/2/fo/2fo -26 / -21 / -46 dBc Doubler Mode -55 dBc fo/2/fo/2fo -26 / -34/ -44 dBc Doubler Mode -61 dBc fo/2/fo/2fo -25/ -52 / -61 dBc RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 524,287 Fractional nominal divide ratio varies (-3 / +4) dynamically max 524,283 7 PLLS WITH INTEGRATED VCO - SMT For theory of operation and register map refer to the "PLLs with Integrated VCOs - RF VCOs Operating Guide". To view the Operating Guide, please visit www.hittite.com and choose HMC837LP6CE from the "Search by Part Number" pull down menu. REF Input Characteristics Max Ref Input Frequency Ref Input Range AC Coupled 1 Ref Input Capacitance 14-Bit R-Divider Range 1 50 200 MHz 2 3.3 Vp-p 5 pF 16,383 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7-2 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Electrical Specifications (Continued) Parameter Condition Min. [1] Typ. Max. Units Phase Detector (PD) PD Frequency Fractional Feedback Mode 0.1 100 MHz PD Frequency Fractional Feedforward Mode (and Register 6 [17:16] = 10) 0.1 80 MHz PD Frequency Integer Mode 0.1 125 MHz 2.54 mA Charge Pump Output Current 0.02 Charge Pump Gain Step Size PD/Charge Pump SSB Phase Noise PLLS WITH INTEGRATED VCO - SMT 7 20 A 50 MHz Ref, Input Referred 1 kHz -143 dBc/Hz 10 kHz Add 1 dB for Fractional -150 dBc/Hz 100 kHz Add 3 dB for Fractional -153 dBc/Hz Logic Inputs VIH Input High Voltage DVDD3V-0.4 DVDD3V V VIL Input Low Voltage 0 0.4 V VOH Output High Voltage DVDD3V-0.4 DVDD3V V VOL Output Low Voltage 0 0.4 V 3.5 V Logic Outputs Power Supply Voltages Analog 3.3V Supplies Digital Supply Analog 5V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD 3.0 3.3 DVDD3V 3.0 3.3 3.5 V VPPCP, VDDCP, VCC1, VCC2 4.8 5 5.2 V Power Supply Currents +5V Analog Charge Pump VPPCP, VDDCP 5.3 mA +5V VCO Core and PLL Buffer VCC2 56 mA +5V VCO Divider and RF Buffer VCC1 36 mA AVDD, VCCHF, VCCPS, VCCPD, RVDD 41 mA +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz DVDD3V 6.5 mA Reg 01h=0, Crystal Not Clocked 10 A Reg 01h=0, Crystal Clocked 100 MHz 10 200 A Power on Reset Typical Reset Voltage on DVDD 700 mV 250 s 10 kHz Offset -91 dBc/Hz 100 kHz Offset -120 dBc/Hz Min DVDD Voltage for No Reset Power on Reset Delay 1.5 V VCO Open Loop Phase Noise at fo/2 [1] This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less. 7-3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Electrical Specifications (Continued) Parameter Condition Min. 1 MHz Offset Typ. Max. Units -147 dBc/Hz 10 MHz Offset -161 dBc/Hz 100 MHz Offset -168 dBc/Hz 10 kHz Offset -85 dBc/Hz 100 kHz Offset -114 dBc/Hz 1 MHz Offset -141 dBc/Hz 10 MHz Offset -162 dBc/Hz 100 MHz Offset -171 dBc/Hz 10 kHz Offset -79 dBc/Hz 100 kHz Offset -108 dBc/Hz 1 MHz Offset -135 dBc/Hz 10 MHz Offset -153 dBc/Hz 100 MHz Offset -166 dBc/Hz VCO Open Loop Phase Noise at fo Closed Loop Phase Noise PLL + VCO at fvco with 93 KHz BW Loop Filter Design[3] Integer, 100 MHz PD 1 kHz Offset -113 dBc/Hz Integer, 100 MHz PD 10 kHz Offset -111 dBc/Hz Integer, 100 MHz PD 100 kHz Offset -112 dBc/Hz Integer, 100 MHz PD 1 MHz Offset -141 dBc/Hz Integer, 100 MHz PD 10 MHz Offset -162 dBc/Hz Integer, 100 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter from 10 KHz to 100MHz -58.1 dBc 132.5 fsec Fractional, 100 MHz PD 1 kHz Offset -112 dBc/Hz Fractional, 100 MHz PD 10 kHz Offset -111 dBc/Hz Fractional, 100 MHz PD 100 kHz Offset -112 dBc/Hz Fractional, 100 MHz PD 1 MHz Offset -141 dBc/Hz Fractional, 100 MHz PD 10 MHz Offset -162 dBc/Hz Fractional, 100 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter from 10 KHz to 100MHz -58.4 dBc 128.5 fsec Closed Loop Phase Noise PLL + VCO at fvco with 176K Hz Loop Filter Design[4] Integer, 100 MHz PD 1 kHz Offset -115 dBc/Hz Integer, 100 MHz PD 10 kHz Offset -118 dBc/Hz Integer, 100 MHz PD 100 kHz Offset -114 dBc/Hz Integer, 100 MHz PD 1 MHz Offset -141 dBc/Hz Integer, 100 MHz PD 10 MHz Offset -162 dBc/Hz Integer, 100 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter Fractional, 100 MHz PD from 10 KHz to 100MHz 1 kHz Offset -62 dBc 87.5 fsec -113 dBc/Hz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 PLLS WITH INTEGRATED VCO - SMT VCO Open Loop Phase Noise at 2fo 7-4 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Electrical Specifications (Continued) Parameter Condition Fractional, 100 MHz PD 10 kHz Offset Fractional, 100 MHz PD Fractional, 100 MHz PD Min. Typ. Max. Units -117 dBc/Hz 100 kHz Offset -114 dBc/Hz 1 MHz Offset -139 dBc/Hz Fractional, 100 MHz PD 10 MHz Offset -161 dBc/Hz Fractional, 100 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter from 10 KHz to 100MHz -61.2 dBc 92.5 fsec Closed Loop Phase Noise PLL + VCO at fvco with 78 KHz BW Loop Filter Design[5] PLLS WITH INTEGRATED VCO - SMT 7 Integer, 50 MHz PD 1 kHz Offset -112 dBc/Hz Integer, 50 MHz PD 10 kHz Offset -108 dBc/Hz Integer, 50 MHz PD 100 kHz Offset -111 dBc/Hz Integer, 50 MHz PD 1 MHz Offset -141 dBc/Hz Integer, 50 MHz PD 10 MHz Offset -163 dBc/Hz Integer, 50 MHz PD 100 MHz Offset -171 dBc/Hz -55.6 dBc Integrated Phase Noise 177 fsec 1 kHz Offset -110 dBc/Hz Fractional, 50 MHz PD 10 kHz Offset -108 dBc/Hz Fractional, 50 MHz PD 100 kHz Offset -110 dBc/Hz Fractional, 50 MHz PD 1 MHz Offset -141 dBc/Hz Fractional, 50 MHz PD 10 MHz Offset -163 dBc/Hz Fractional, 50 MHz PD 100 MHz Offset RMS Jitter Fractional, 50 MHz PD Integrated Phase Noise RMS Jitter from 10 KHz to 100MHz -171 dBc/Hz -55.8 dBc 171 fsec Closed Loop Phase Noise PLL + VCO at fvco with 142 KHz Loop Filter Design[6] Integer, 50 MHz PD 1 kHz Offset -114 dBc/Hz Integer, 50 MHz PD 10 kHz Offset -112 dBc/Hz Integer, 50 MHz PD 100 kHz Offset -114 dBc/Hz Integer, 50 MHz PD 1 MHz Offset -141 dBc/Hz Integer, 50 MHz PD 10 MHz Offset -162 dBc/Hz Integer, 50 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter from 10 KHz to 100MHz -60 dBc 106.8 fsec Fractional, 50 MHz PD 1 kHz Offset -111 dBc/Hz Fractional, 50 MHz PD 10 kHz Offset -112 dBc/Hz Fractional, 50 MHz PD 100 kHz Offset -113 dBc/Hz Fractional, 50 MHz PD 1 MHz Offset -135 dBc/Hz Fractional, 50 MHz PD 10 MHz Offset -154 dBc/Hz Fractional, 50 MHz PD 100 MHz Offset -171 dBc/Hz Integrated Phase Noise RMS Jitter Figure of Merit Floor Integer Mode 7-5 from 10 KHz to 100MHz from 10 KHz to 100MHz -59.4 dBc 114 fsec -230 dBc/Hz Normalized 1 Hz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Electrical Specifications (Continued) Parameter Condition Min. Typ. Max. Units Floor Fractional Mode -227 dBc/Hz Flicker (Both Modes) -268 dBc/Hz [2] The Close Loop Phase Noise PLL+VCO at fvco/2 can be calculated by subtracting 6dB. The Close Loop Phase Noise PLL+VCO at 2fvco can be calculated by adding 6dB. Loop Filter Configuration Table C1 (pF) C2 (nF) C3 (pF) C4 (pF) R2 (k) R3 (k) R4 (k) [3] 820 15 130 130 0.39 1 1 [4] 120 5.1 82 82 0.75 1 1 [5] 270 10 150 150 0.68 2 2 [6] 120 5.6 68 68 1.2 1 1 Loop Filter Design For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 PLLS WITH INTEGRATED VCO - SMT Loop Filter Configuration 7-6 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Typical Closed Loop Fractional Phase Noise [1] Closed Loop Integer Phase Noise -100 -120 -140 -160 50MHz PFD 78KHz BW 177 fsec 50MHz PFD 142KHz BW 106 fsec 100MHz PFD 93KHz BW 132 fsec 100MHz PFD 176KHz BW 87 fsec -180 3 10 10 4 7 10 5 10 6 10 7 10 -120 -140 -160 50MHz PFD 78KHz BW 171 fsec 50MHz PFD 142KHz BW 114 fsec 100MHz PFD 93KHz BW 128 fsec 100MHz PFD 176KHz BW 92 fsec -180 3 10 8 10 4 10 Free Running Phase Noise 10 6 10 7 1100 -40 fmax -60 n2 kvco (MHz/V) -80 n0 1050 1095 MHz FF 2190 MHz FF 4380 MHz FF fmax 1000 -100 -120 950 -140 fmin n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 n28 n30 n31 -160 -180 2 10 900 10 3 10 4 10 5 10 6 10 7 10 0 1 8 2 3 4 5 TUNING VOLTAGE (V) OFFSET FREQUENCY (Hz) Free Running VCO Phase Noise Over Temperature Typical VCO Tuning Voltage After Calibration 5 TUNE VOLTAGE AFTER CALIBRATION (V) -110 100 kHz Offset -120 +27C +85C -40C -130 1 MHz Offset -140 -150 10 MHz Offset -160 -170 2050 2100 2150 2200 2250 2300 4 fmin 3 31 fmax 15 2 1 0 VCO FREQUENCY FREQUENCY (MHz) [1] RMS Jitter data are measured from 10KHz to 100MHz bandwidth. 7-7 10 8 Typical Tuning Curves vs. Switch Position -20 PHASE NOISE (dBc/Hz) 5 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) PHASE NOISE (dBc/Hz) PLLS WITH INTEGRATED VCO - SMT PHASE NOISE (dBc/Hz) @2107MHz PHASE NOISE (dBc/Hz) @2100MHz -100 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 0 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Typical VCO Sensitivity vs. Cap @ Fo Voltage Typical Output Power - Narrow Band Match 20 40 35 25 20 Typical Operating Range 15 10 15 Divide-by-2 Fundamental -40C 10 -40C 27C 27C 85C 85C 5 Doubler -40C 0 27C 5 85C -5 1000 0 0 1 2 3 4 5 TUNING VOLTAGE (V) 2000 3000 4000 OUTPUT FREQUENCY (MHz) Figure of Merit NORMALIZED PHASE NOISE (dBc/Hz) -200 -210 Typ FOM vs Offset -220 FOM Floor FOM 1/f Noise -230 -240 2 10 10 3 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5000 6000 7 PLLS WITH INTEGRATED VCO - SMT kvco (MHz/V) OUTPUT POWER (dBm) TUNING CAP 31 1992MHz AT 2V TUNING CAP 15 2149MHz AT 2V TUNING CAP 0 2364MHz AT 2V 30 7-8 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Pin Descriptions PLLS WITH INTEGRATED VCO - SMT 7 7-9 Pin Number Function Description 1 AVDD DC Power Supply for analog circuitry. 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 VPPCP Power Supply for charge pump analog section 4 CP Charge Pump Output 7 VDDCP Power Supply for the charge pump digital section 10 RVDD Reference Supply 15 XREFP Reference Oscillator Input 16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry 17 CEN Chip Enable. Connect to logic high for normal operation. 23 VTUNE VCO Varactor. Tuning Port Input. 25 VCC2 VCO Analog Supply 2 27 VCC1 VCO Analog Supply 1 28 RF_N [1] RF Positive Output 29 [1] 30 RF_P SEN RF Negative Output PLL Serial Port Enable (CMOS) Logic Input 31 SDI PLL Serial Port Data (CMOS) Logic Input 32 SCK PLL Serial Port Clock (CMOS) Logic Input 33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) 35 VCCHF DC Power Supply for Analog Circuitry 36 VCCPS DC Power Supply for Analog Prescaler 39 VCCPD DC Power Supply for Phase Detector 40 BIAS External bypass decoupling for precision bias circuits. Note: 1.920V 20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10G meter such as Agilent 34410A, normal 10M DVM will read erroneously. [1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS -0.3V to +3.6V VPPCP, VDDCP, VCC1 -0.3V to +5.8V VCC2 -0.3V to +5.5V Operating Temperature -40C to +85C Storage Temperature -65C to 125C Maximum Junction Temperature 125 C Thermal Resistance (RTH) (junction to ground paddle) 20 C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reflow Soldering 260C Time at Peak Temperature 40 sec ESD Sensitivity (HBM) 7 Class 1B Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. PLLS WITH INTEGRATED VCO - SMT Peak Temperature Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC837LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H837 XXXX [1] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 10 HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Evaluation PCB PLLS WITH INTEGRATED VCO - SMT 7 7 - 11 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC837LP6CE from the "Search by Part Number" pull down menu to view the product splash page. Evaluation Order Information Item Contents Evaluation PCB Only Evaluation Kit Part Number HMC837LP6CE Fo/2 & Fo Evaluation PCB EVAL01-HMC837LP6CE HMC837LP6CE 2xFo Evaluation PCB EVAL02-HMC837LP6CE HMC837LP6CE Fo/2 & Fo Evaluation PCB USB Interface Board 6' USB A Male to USB B Female Cable CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software, Hittite PLL Design Software) 131995-HMC837LP6CE HMC837LP6CE 2xFo Evaluation PCB USB Interface Board 6' USB A Male to USB B Female Cable CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software, Hittite PLL Design Software) 131997-HMC837LP6CE For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC837LP6CE v00.1210 FRACTIONAL-N PLL WITH INTEGRATED VCO 1025 - 1150, 2050 - 2300, 4100 - 4600 MHz Notes: PLLS WITH INTEGRATED VCO - SMT 7 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 12 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC837LP6CE HMC837LP6CETR 131997-HMC837LP6CE 131995-HMC837LP6CE