Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Intellimod™ Module
Three Phase
IGBT Inver ter Output
50 Amperes/1200 Volts
PM50CSD120
1
Description:
Powerex Intellimod™ Intelligent
Power Modules are isolated base
modules designed for power
switching applications operating
at frequencies to 20kHz. Built-in
control circuits provide optimum
gate drive and protection for the
IGBT and free-wheel diode
power devices.
Features:
□Complete Output Power
Circuit
□Gate Drive Circuit
□Protection Logic
–Shor t Circuit
–Over Current
–Over Temper ature
–Under Voltage
□Low Loss Using 4th Generation
IGBT Chip
Applications:
□Inverters
□UPS
□Motion/Ser vo Control
□Power Supplies
Ordering Information:
Example: Select the complete
par t number from the table below
-i.e. PM50CSD120 is a 1200V,
50 Ampere Intellimod™ Intelligent
Power Module.
Type Current Rating VCES
Amperes Volts (x 10)
PM 50 120
Outline Drawing and Circuit Diagram
Dimensions Inches Millimeters
A 4.33±0.04 110.0±1.0
B 3.74±0.02 95.0±0.5
C 3.50±0.04 89.0±1.0
E 2.91±0.02 74.0±0.5
F2.62 66.44
G1.28 32.6
H1.24 31.6
J1.02 26.0
K0.94 24.0
L0.87 +0.04/-0.02 22.0 +1.0/-0.5
M0.79 20.0
N0.76 19.4
P0.18 4.5
Q0.10 2.54
Dimensions Inches Millimeters
R0.67 17.02
S0.67 17.02
T0.52 13.2
U0.39 10.0
V0.16 4.0
W0.02 0.5
Y0.24 Rad. Rad. 6.0
Z0.22 Dia. Dia.5.5
AA M5 M5
AB 0.13 3.22
AC 0.06 1.6
AD 0.08±0.02 2.0±0.5
AG 0.020.01 0.5±0.3
AH 0.47 12.0
SA
AH U
Z
(4 PLACES)
F
AB
PQ
(2 PLACES)
AC
L
B
M
M
AD
AG J J
E
UU
U
R
A
N
G H
V
C
T
1.
2.
3.
4.
5.
6.
7.
8.
9.
V
V
V
V
V
V
V
10.
11.
12.
13.
14.
15.
16.
U
U
VV
W
W
WPC
UPI
VPI
WPI
NC
NI
P
N
P
P
N
N
UPC
F
O
V
VPC
78 9
10
11 13 151234 56
N
V
W
U
BP
17.
18.
19.
NC
WF
O
O
VF
O
UF
AA - THD
AD
12
14 16
18
17 19
(19 TYP.)
Y (4 PLACES)
W SQ. PIN
V
VCC
SI
GND GND
OUT UPI
V
UFO
UP
UPC
FO
IN
VCC
SI
GND GND
OUT FO
IN
VCC
SI
GND GND
OUT FO
IN
V
V
FO
V
V
FO
VPI
V
VP
VPC
WPI
W
WP
WPC
VCC
SI
GND GND
OUT FO
IN
VCC
SI
GND GND
OUT FO
IN
UN
VCC
SI
GND GND
OUT FO
IN
V
V
W
NV
NI
N
NC
TEMP
NC
FO
P
U
V
W
NNC
(6 PLACES)
PM50CSD120
Intellimod™ Module
Three Phase IGBT Inver ter Output
50 Amperes/1200 Volts
2
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Absolute Maximum Ratings, Tj = 25°C unless otherwise specified
Characteristics Symbol PM50CSD120 Units
Power Device Junction Temperature Tj-20 to 150 °C
Storage Temperature Tstg -40 to 125 °C
Case Operating Temperature*TC-20 to 100 °C
Mounting Torque, M5 Mounting Screws — 31 in-lb
Mounting Torque, M5 Main Terminal Screws — 31 in-lb
Module W eight (Typical) — 560 Grams
Supply Voltage Protected by OC and SC VCC(prot.) 800 Volts
(VD = 13.5 - 16.5V, Inverter Part) Tj = 125°C Start
Isolation Voltage, AC 1 minute, 60Hz Sinusoidal VISO 2500 Volts
IGBT Inverter Sector
Collector-Emitter Voltage (VD = 15V, VCIN = 15V) VCES 1200 Volts
Collector Current, ± (TC = 25°C) IC50 Amperes
Peak Collector Current, ± (TC = 25°C) ICP 100 Amperes
Supply Voltage (Applied between P - N) VCC 800 Volts
Supply Voltage, Surge (Applied between P - N) VCC(surge) 1000 Volts
Collector Dissipation (TC = 25°C) PC328 Watts
Control Sector
Supply Voltage Applied between (VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC)V
D20 Volts
Input Voltage Applied between (UP-VUPC, VP-VVPC, WP-VWPC, UN, VN, WN-VNC)V
CIN 20 Volts
Fault Output Supply Voltage Applied between VFO 20 Volts
(UFO-VUPC, VFO-VVPC, WFO-VWPC, FO-VNC)
Fault Output Current (UFO, VFO, WFO, FO)I
FO 20 mA
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
IGBT Inverter Sector
Collector Cutoff Current ICES VCE = VCES, Tj = 25°C, VD = 15V — — 1.0 mA
VCE = VCES, Tj = 125°C, VD = 15V — — 10 mA
Diode Forward Voltage VEC -IC = 50A, VD = 15V, VCIN = 15V — 2.5 3.5 Volts
Collector-Emitter VCE(sat) VD = 15V, VCIN = 0V, IC = 50A, Pulsed, Tj = 25°C— 2.4 3.2 Volts
Saturation V oltage VD = 15V, VCIN = 0V, IC = 50A,Pulsed, Tj = 125°C— 2.1 2.8 Volts
Inductive Load Switching Times ton 0.5 1.0 2.5 µS
trr VD = 15V, VCIN = 0 ~ 15V — 0.15 0.3 µS
tC(on) VCC = 600V, IC = 50A — 0.4 1.0 µS
toff Tj = 125°C, Inductive Load — 2.5 3.5 µS
tC(off) —0.7 1.2 µS
*TC Measure Point
63MM TC
3
PM50CSD120
Intellimod™ Module
Three Phase IGBT Inver ter Output
50 Amperes/1200 Volts
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Control Sector
Over Current Trip Level OC Tj = 25°C93157 — Amperes
(VD = 15V) Tj = 125°C59——Amperes
Short Circuit Trip Level SC -20°C ≤ Tj ≤ 125°C, VD = 15V — 183 — Amperes
Over Current Delay Time toff(OC) VD = 15V — 10 — µS
Over Temperature Protection (VD = 15V) OT Trip Level 111 118 125 °C
(Lower Arm) OTRReset Level — 100 — °C
Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts
(-20 ≤ Tj ≤ 125°C) UVRReset Level — 12.5 — Volts
Circuit Current IDVD = 15V, VCIN = 15V, VN1-VNC —4055mA
VD = 15V, VCIN = 15V, VXP1-VXPC —1318mA
Input ON Threshold Voltage VCIN(on) Applied between UP-VUPC, VP-VVPC,1.2 1.5 1.8 Volts
Input OFF Threshold Voltage VCIN(off) WP-VWPC, UN, VN, WN-VNC 1.7 2.0 2.3 Volts
Fault Output Current* IFO(H) VD = 15V, VCIN = 15V — — 0.01 mA
IFO(L) VD = 15V, VCIN = 15V — 10 15 mA
Minimum Fault Output Pulse Width* tFO VD = 15V 1.0 1.8 — mS
*Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower arm device operate to protect it.
Thermal Characteristics
Characteristic Symbol Condition Min. Typ. Max. Units
Junction to Case Thermal Resistance Rth(j-c)Q Each IGBT — — 0.38 °C/Watt
Inverter Part Rth(j-c)F Each FWDi — — 0.70 °C/Watt
Rth(j-c´)Q Each IGBT** — — 0.23†°C/Watt
Rth(j-c´)F Each FWDi** — — 0.36†°C/Watt
Contact Thermal Resistance Rth(c-f) Case to Fin Per Module, — — 0.027 °C/Watt
Thermal Grease Applied
**TC measured point is just under the chips.
†If you use this value, Rth(f-a) should be measured just under the chips.
Recommended Conditions for Use
Characteristic Symbol Condition Value Units
Supply V oltage VCC Applied across P-N Terminals 0 ~ 800 Volts
Control Supply Voltage*** VDApplied between VUP1-VUPC, 15 ± 1.5 Volts
VN1-VNC, VVP1-VVPC, VWP1-VWPC
Input ON Voltage VCIN(on) Applied between UP-VUPC, VP-VVPC,0 ~ 0.8 Volts
Input OFF Voltage VCIN(off) WP-VWPC, UN, VN, WN-VNC 4.0 ~ VDVolts
PWM Input Frequency fPWM Using Application Circuit 0 ~ 20 kHz
Minimum Dead Time tDEAD Input Signal ≥ 3.0 µS
***With ripple satisfying the following conditions: dv/dt ≤ ±5v/µs, Variation ≤ 2V peak to peak.
PM50CSD120
Intellimod™ Module
Three Phase IGBT Inver ter Output
50 Amperes/1200 Volts
4
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
0
1.0
2.0
3.0
SATURATION VOLTAGE
CHARACTERISTICS (TYPICAL)
COLLECTOR CURRENT, IC, (AMPERES)
SATURATION VOLTAGE, VCE(sat), (VOLTS)
06020 40
VD = 15V
VCIN = 0V
Tj = 25oC
Tj
= 125oC
2.5
1.5
0.5
10
0
10
1
10
2
DIODE FORWARD CHARACTERISTICS
(TYPICAL)
DIODE FORWARD VOLTAGE, VEC, (VOLTS)
DIODE CURRENT, -IC, (AMPERES)
0.5 1.0 1.5 2.0 2.5
Tj
= 25oC
Tj
= 125oC
0
VD = 15V
10
0
10
1
10
2
10
-1
COLLECTOR CURRENT, IC, (AMPERES)
SWITCHING TIMES, ton, toff, (µs)
SWITCHING TIME VS.
COLLECTOR CURRENT (TYPICAL)
ton
10
0
10
1
toff
VCC = 600V
VD = 15V
Tj
= 25oC
T
j
= 125oC
10
0
10
1
10
2
10
-1
COLLECTOR CURRENT, IC, (AMPERES)
SWITCHING TIMES, tc(on), tc(off), (µs)
SWITCHING TIME VS.
COLLECTOR CURRENT (TYPICAL)
tc(on)
10
0
10
1
tc(off)
tc(off)
VCC = 600V
VD = 15V
Tj = 25oC
Tj = 125oC
10
0
10
1
10
2
10
-2
COLLECTOR CURRENT, -IC, (AMPERES)
REVERSE RECOVERY TIME, trr, (µS)
REVERSE RECOVERY CURRENT VS.
COLLECTOR CURRENT (TYPICAL)
10
-1
10
0
VCC = 600V
VD = 15V
INDUCTIVE LOAD
Tj
= 25oC
Tj = 125oC
10
0
REVERSE RECOVERY CURRENT, Irr, (AMPERES)
10
1
10
2
trr
Irr
0
0
40
60
80
100
CIRCUIT CURRENT VS.
CARRIER FREQUENCY
CARRIER FREQUENCY, fC, (kHz)
CIRCUIT CURRENT, ID, (mA)
510152025
Tj = 25oC
N-SIDE
P-SIDE
20
INDUCTIVE LOAD
10
0
10
1
10
2
10
-1
SWITCHING LOSS, ESW, (m)J/PULSE)
SWITCHING LOSS CHARACTERISTICS
(TYPICAL)
100
101
VCC = 600V
VD = 15V
INDUCTIVE LOAD
Tj
= 25oC
Tj = 125oC
Esw(off)
Esw(off)
Esw(on)
Esw(on)
TIME, (s)
TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE)
TRANSIENT THERMAL
IMPEDANCE CHARACTERISTICS
(IGBT & FWDi - INVERTER PART)
10
1
10
-1
10
0
10
1
10
0
10
-1
10
-2
10
-3
STANDARD VALUE
Rth(j-c)Q = 0.38oC/W (IGBT)
Rth(j-c)F = 0.70oC/W (FWDi)
SINGLE PULSE
10
-2
10
-3
COLLECTOR CURRENT, IC, (AMPERES)
INDUCTIVE LOAD
0
1.0
2.0
3.0
COLLECTOR-EMITTER SATURATION
VOLTAGE (TYPICAL)
SUPPLY VOLTAGE, VD, (VOLTS)
SATURATION VOLTAGE, VCE(sat), (VOLTS)
1201813 14 15 16 17
IC = 50A
Tj = 25oC
Tj
= 125oC
1.5
2.5
0.5
