TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 1 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 1.0 GENERAL Scope This specification covers the insulation piercing QuickieTM Connector designed for printed wiring board-toflat cable (round conductor) interconnection in low power applications. In all applications the mated system (header to receptacle) plating should be gold to gold or tin to tin. The specification is composed of the following sections. Paragraph 1.0 2.0 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 4.0 4.1 4.2 4.3 4.4 4.5 2.0 Title Page GENERAL APPLICABLE DOCUMENTS REQUIREMENTS Qualification Material Finish Design and Construction Electrical Characteristics Mechanical Characteristics Environmental Conditions QUALITY ASSURANCE PROVISIONS Equipment Calibration Inspection Conditions Qualification Inspection Quality Conformance Inspection Acceptance Inspection 1 1 2 2 3 3 7 9 11 13 17 17 17 17 18 20 APPLICABLE DOCUMENTS The following documents, of the issue in effect on the date of the latest revision of this specification, shall form a part of this specification to the extent specified herein. SPECIFICATIONS Military MIL-M-245l9 MIL-G-45204 MIL-G-45662 MIL-P-55110 Copyright Molding Plastics, Polyester, Thermoplastic Gold Plating, Electrodeposited Calibration System Requirement Printed Wiring Boards FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 2 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED Federal QQ-N-290 QQ-W-343 QQ-B-750 QQ-S-763 QQ-C-533 Nickel Plating (Electrodeposited) Wire, Electrical and Non-Electrical, Copper (Uninsulated) Bronze, Phosphor; Bar, Plate, Rod, Sheet Strip, Flat Wire, and Structural and Special Shaped Sections Steel Bars, Shapes, and Forgings, Corrosion-Resisting. Be - Cu STANDARDS Military MIL-STD-l05 MIL-STD-202 MIL-STD-275 MIL-STD-l344 Sampling Procedures and Tables for Inspection by Attributes Test Methods for Electronic and Electrical Component Parts Printed Wiring Board for Electronic Equipment Test Methods for Electrical Connectors Industry Specifications/Standards UL-94 Tests for Flammability of Plastic Materials FCI Test Specifications BUS-12-00l 3.0 Round Conductor Flat Flexible Cable REQUIREMENTS 3.1 Qualification Connectors furnished under this specification shall be products capable of meeting the qualification test requirements specified herein. 3.2 Material The material for each part shall be as specified herein, or equivalent. Substitute material shall meet the performance requirements of this specification. Copyright 3.2.1 Contact. Both the header and receptacle contact shall be full-hard phosphor bronze in accordance with QQ-B-750, Composition A. 3.2.2 Latch. The standard Quickie shall have a plastic molded-in latch. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 3 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.2.3 3.3 Plastic Parts. Except as subsequently specified, all molded plastic parts of the receptacle connector and the mating header shall be filled polyester in accordance with MIL-M24519, Type GPT-30F. Except as noted, all plastic material shall be rated flame retardant 94V-0 in accordance with UL-94. 3.2.3.1 Header Locking Latches (Optional). The latches shall be polyester in accordance with MIL-M-24519, Type PT-F. 3.2.3.2 Strain Relief (Optional). The strain relief shall be unfilled thermoplastic material. 3.2.3.3 Keys (Optional). The keys shall be unfilled Type 6-6 Nylon; the material shall be rated flame retardant 94V-2 in accordance with UL-94. Finish The finish for each part shall be as specified herein. Substitute finishes shall meet the performance requirements of this specification. 3.3.1 Both the header and receptacle contacts shall be plated with either gold per MIL-45204B, GXT, or with tin-lead. Nickel shall be plated per QQ-N-290, Class 2. 3.3.2 QUICKIE II CONNECTOR SYSTEM DUAL BEAM PHOSPHOR BRONZE FEMALE CONTACT Receptacle Contact Mating Contact Remainder of Plating Designation Portion Terminal ___________________________________________________________ 0.76um/30 u" Au Copyright 0.76um/30 u" Au Over 1.27um/50 u" Ni 1.27um/50 u" Ni FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 4 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED FIGURE 1 Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE REVISION QuickieTM Connector System 5 of 20 AUTHORIZED BY F DATE 31 Jul 06 M.Barrios CLASSIFICATION UNRESTRICTED QUICKIE II HEADERS AVAILABLE IN BOTH ROUND AND SQUARE PINS SAME PLATING ON HEADER CONTACT AND SOLDER TAIL Mating Contact Pin Surface Plating Designation See Figure 1 Plating Detail ______________________________________________________________________ 0.76um/30m" Au ALL PIN SIDES 0.76um/30 u" Au over 1.27um/50 u" Ni 0.76um/30m" GXT ALL PIN SIDES 0.69um/27 u" Pb-Ni WITH 0.07um/3 u" Au FLASH OVER 1.27um/50 u" Ni QUICKIE III & EURO QUICKIE HEADERS AVAILABLE IN SQUARE PIN CONFIGURATION DUPLEX PLATING WITH THE FOLLOWING SOLDER TAIL PLATING ON ALL VERSIONS - 3.81mm/150 u" MIN TIN-LEAD Mating Contact Pin Surface Plating Designation See Figure 1 Plating Detail __________________________________________________________________________ TIN-LEAD ALL PIN SIDES 3.81um/150 u" MIN TIN-LEAD OVER 1.27um/50 u" Ni 0.76um/30 GXT ALL PIN SIDES 0.69um/27 u" Pb-Ni with 0.07um/3 u" Au Flash OVER 1.27um/50u" Ni 0.76um/30 u" Au ALL PIN SIDES 0.76um/30 u" Au OVER 1.27um/50 u" 1.27um/50 u" Au ALL PIN SIDES 1.27um/50 u" Au OVER 1.27um/50" Ni 3.4 Copyright Design and Construction FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 6 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED The connector system shall be of two-piece design, consisting of: a molded, straight or right-angle, shielded header having .64/0.025 diameter or .64/0.025 square header contacts arranged for printed wiring board termination on a 2.54/0.100 square grid; and a multi-piece receptacle connector having self-stripping contact terminations for flat, flexible, round conductor cable on a 1.27/0.050 inch center and either one single-ended or two single-ended cantilever members for interfacing with the header contact. NOTE: While the receptacle connector will mate with any .64/0.025 diameter or .64/0.025 square header contacts on an appropriate grid, performance of such a combination must be determined by actual test. Minimum pin length is 4.32/.170", maximum pin length is 6.35/.250". Recommended pin length is 5.84/.230". 3.4.1 Copyright Installation. 3.4.1.1 Header. The header shall mount on single- or double-sided or multilayered printed wiring board of any thickness to + .08/.003 inch (Size 4) having .89/0.035 + 0.003 diameter holes (Round Pin) or 1.02/.040 + .08/.003 diameter holes (square pin) on a 2.54/0.0100 square grid. The termination layout shall be in accordance with the printed wiring requirements of MIL-STD-275 and MIL-P-55110. 3.4.1.2 Receptacle. The receptacle shall simultaneously terminate up to 60 wires size AWG #28 (stranded) or AWG #30 (solid) on 1.27/0.050 inch centers without pre-stripping the PVC (polyvinylchloride) cable insulation. The cable shall conform to the requirements of specifications BUS-12-001. 3.4.2 Latching Mechanism. An optional latching mechanism shall be available for locking the plug into the receptacle to withstand service conditions without disconnecting. 3.4.3 Strain Relief. An optional strain relief shall be available to protect the receptacle terminations against pull and flexing forces. 3.4.4 Polarizing Feature. An optional molded-in polarizing feature shall be available to insure correct orientation of the receptacle connector and its mating header. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 7 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.5 3.4.5 Keying. An optional key(s) shall be available for installation in individual positions in the receptacle connector to permit selective identification or programming. 3.4.6 Mating. The connector shall be capable of mating and unmating by hand without the use of special tools within the specified temperature range. 3.4.7 Workmanship. Connectors shall be uniform in quality and shall be free from burrs, scratches, cracks, voids, chips, blisters, pin holes, sharp edges, and other defects that will adversely affect life or serviceability. 3.4.8 Interchangeability. Any header shall be capable of mating with any receptacle of the same contact population without degradation in performance. Electrical Characteristics 3.5.1 Current Rating. The maximum current rating of the connector shall be 1.0 ampere DC. 3.5.2 Contact Resistance. The contact resistance shall not exceed 10 milliohms (15 milliohms after exposure to the environments described in paragraphs 3.6.5 and 3.7.1 to 3.7.7) when measured in accordance with MIL-STD-202, Method 307. The following details shall apply: (a) Method of Connection - attach current and voltage leads as shown in Figure 1. (b) Test Current - 1.0 ampere DC. 3.5.3 Low Level Circuit Resistance. The low level circuit resistance shall not exceed 10 milliohms (15 milliohms after exposure to the environments described in paragraphs 3.6.5 and 3.7.1 to 3.7.7) when measured in accordance with MIL-STD-1344, Method 3002. The following details shall apply. (a) Method of Connection - see Figure 2 (b) Test Current - 1 milliampere DC (c) Maximum Open Circuit Voltage-20 millivolts DC Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 8 of 20 AUTHORIZED BY F DATE 31 Jul 06 M.Barrios CLASSIFICATION UNRESTRICTED 3.5.4 Insulation Resistance. The insulation resistance of mated connectors shall be not less than 50,000 megohms (20,000 megohms after exposure to the humidity environment described in paragraph 3.7.1) when measured in accordance with MIL-STD-202, Method 302. The following details shall apply: (a) Test Condition - B (500 volts DC) (b) Special Preparation* - the header and receptacle shall not be terminated. (c) Points of Measurement - between adjacent contact positions. FIGURE 2 - CONTACT RESISTANCE Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 9 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.5.5 Dielectric Withstanding Voltage. There shall be no evidence of arc-over, insulation breakdown, or excessive leakage current (> 1 milliampere) when the mated connectors are tested in accordance with MIL-STD-202, Method 301. The following details shall apply: (a) Test Potential - 1,000 volts RMS, 60 Hz at sea-level pressure 450 volts RMS, 60 Hz at 50,000 feet simulated altitude. (b) Test Duration - 60 seconds (c) Special Preparation* - the header and receptacle shall not be terminated. (d) Points of Measurement - between adjacent contact positions. 3.6 Mechanical Characteristics 3.6.1 Cable Retention. The strain relief on the receptacle shall withstand an evenly distributed force of 10 pounds per-inch-of-cable-width (.146 Newtons per-millimeter-of-cable-width) applied to the cable in a direction parallel to the contact axis. 3.6.2 Cable Flex Resistance**. With strain relief installed, the receptacle shall withstand 100 cycles of cable flexing. The following details shall apply: (a) Tension on Cable - 2 pounds per-inch-of-cable-width (0.029 Newtons per-millimeterof-cable width) (b) Flex Angle - 140o as shown in Figure 3. * The layout of land areas on printed wiring boards and the proximity of adjacent conductors at the cut end of flexible cables can affect this characteristic and, therefore, are necessarily excluded in its specification. ** Stranded wire only; solid conductors will not withstand flexing, whether or not a connector is installed. 3.6.3 Copyright Total Mating Force. The total force to mate the header and receptacle shall not exceed the values shown in Table I. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION BUS-12-082 TITLE PAGE QuickieTM Connector System REVISION 10 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED TABLE I - TOTAL INSERTION FORCE Contact Population 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 X X X X X X X X X X x X x X X 3 4 5 7 8 10 12 13 15 17 20 22 25 30 32 Force Pounds 3 4 5 7 8 10 12 14 15 19 23 25 30 35 38 Nts. 13.4 17.8 22.3 31.2 35.6 44.5 53.4 57.9 66.8 75.7 89 98 111.3 133.5 142.4 FIGURE 3 - CABLE FLEX RESISTANCE Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 11 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.6.4 Individual Contact Separation Force. When measured using a gage configured as shown in Figure 4, the individual contact separation force shall be not less than 25 grams. FIGURE 4 - SEPARATION FORCE GAGE 3.7 3.6.5 Durability. After 100 mating cycles of the header and receptacle receptacle, the individual contact separation force shall be not less than specified above (see paragraph 3.6.4) and the contact resistance shall not exceed 15 milliohms (see paragraph 3.5.2). 3.6.6 Contact to Housing Retention. The force required to dislodge the receptacle terminal from its housing cavity shall be 1 Lb. minimum prior to cable termination or assembly of strain reliefs. Environmental Conditions 3.7.1 Humidity. Within 1 hour after exposure of the mated connector to a high humidity environment, the insulation resistance of an unterminated connector shall be not less than 20,000 megohms (see paragraph 3.5.4); the contact resistance of a terminated connector shall not exceed 15 milliohms (see paragraph 3.5.2). The test shall be in accordance with MIL-STD-202, Method l03; the following details shall apply: (a) Test Duration - 96 hours (b) Relative Humidity - 90% minimum (c) Temperature - 40oC Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 12 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.7.2 Thermal Shock. After exposure of the mated connector to alternate periods of extreme high and low temperature, there shall be no evidence of cracking or crazing of the insulator or other physical damage to the connector; the dielectric withstanding voltage of an unterminated connector shall be not less than 1,000 volts RMS, 60 Hz (see paragraph 3.5.5). The test shall be in accordance with MIL-STD-202, Method 107; the following details shall apply: (a) Test Condition - B (1 hour cycles) (b) Temperature Range* - -65 to +105oC 3.7.3 High Temperature Life. After exposure of the mated connector to a high temperature operating environment, the insulation resistance of an unterminated connector shall be not less than 100,000 megohms (see paragraph 3.5.4); the contact resistance of a terminated connector shall not exceed 15 milliohms (see paragraph 3.5.2). The test shall be in accordance with MIL-STD-202, Method 108; the following details shall apply: (a) Test Chamber Temperature - 85oC (b) Test Condition (Duration)- B (250 hours) (c) Operating Conditions - 1.0 ampere DC current (rated) through all contacts of terminated connector; duty cycle: 45 minutes ON and 15 minutes OFF. 3.7.4 Shock. There shall be no evidence of physical or mechanical damage when the mated connectors are subjected to transient accelerations. During and after each shock, the contacts shall evidence no discontinuity greater than 1 microsecond. The test shall be in accordance with MIL-STD-202, Method 213. The following details shall apply: (a) Test Condition - I (l00G, 6ms sawtooth) (b) Number of Shocks - 3 shocks in each direction along three orthogonal axes (18 total) (c) Mounting - see Figure 5 Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 13 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 3.7.5 Vibration. There shall be no evidence of physical or mechanical damage when the mated connectors are subjected to prolonged mechanical vibration; during the vibration along each axis, the contacts shall evidence no discontinuity greater than l microsecond. At the completion of the test, the individual contact separation force shall be not less than specified in paragraph 3.6.4 and the contact resistance shall not exceed 15 milliohms (see paragraph 3.5.2). The test shall be in accordance with MIL-STD-202, Method 204; the following details shall apply: (a) Test Condition - B (+15G, 10 to 2,000 Hz) (b) Test Duration - 4 hours along each of three orthogonal axes (12 hours total) (c) Mounting - see Figure 5 * The high temperature limit for polyester is +l50oC; however, the PVC insulation of the cable restricts the assembly to +l05oC. 3.7.6 Hydrogen Sulfide (H2S) Exposure. After exposure of the mated connectors to an H2S atmosphere, the low level circuit resistance shall not exceed l5 milliohms (see paragraph 3.5.3). The following details shall apply: (a) Test Medium - solution of 120 grams of Na2S.9H20 in 500 ml of distilled water, with 14 grams of K2HPO4 added immediately prior to test. (b) Test Temperature - 40oC (c) Test Duration - 48 hours in a sealed 9000 cc glass container. 3.7.7 Salt Spray. After exposure of the mated connectors to a salt fog atmosphere, the low level circuit resistance and contact resistance shall not exceed 15 milliohms (see paragraphs 3.5.3 and 3.5.2, respectively) when measured in that order. The test all be in accordance with MIL-STD-202, Method l0l; the following details shall apply: (a) Salt Solution - 5 percent by weight (b) Test Condition - B (48 hours) Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 14 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED FIGURE 5 - MOUNTING FOR SHOCK AND VIBRATION Copyright FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 15 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 4.0 QUALITY ASSURANCE PROVISIONS 4.1 Equipment Calibration All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with MIL-C-45662. 4.2 Inspection Conditions Unless otherwise specified herein, all inspections shall be performed under the following ambient conditions. (a) Temperature - 25oC + 5oC (b) Relative Humidity - 30 to 80% (c) Barometric Pressure - Local Ambient 4.3 Qualification Inspection Qualification inspection shall be performed on sample units produced with equipment and procedures normally used in production. Copyright 4.3.1 Sample. Six (6) of the largest and three (3) of the smallest population connectors shall be subjected to the qualification inspection. 4.3.2 Preparation of Samples. The various test samples shall be configured and terminated as shown in Table II. 4.3.3 Test Sequence. The sample connectors shall be subjected to the inspections specified in Table III in the order shown. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION BUS-12-082 TITLE PAGE QuickieTM Connector System REVISION 16 of 20 AUTHORIZED BY F DATE 31 Jul 06 M.Barrios CLASSIFICATION UNRESTRICTED TABLE II - TEST SAMPLE DESCRIPTION Sample Number Number of Contacts 1 2 3 4 5 6 7 8 9 2 2 2 2 2 2 2 2 2 x x x x x x x x x Strain Relief 25 25 25 25 25 25 5 5 5 Wire Latches Yes No No Yes Yes No Yes Yes No Size No No No Yes Yes No No Yes No AWG AWG -AWG AWG AWG AWG AWG AWG Type 28 28 Length Stranded Stranded None Stranded Stranded Solid Stranded Stranded Solid 28 28 30 28 28 30 10" 10" -10" 10" 10" 10" 10" 10" TABLE III - CONNECTOR QUALIFICATION INSPECTION Examination or Test Paragraph Total Mating Force Individual Contact Separation Force Contact to Housing Retention Cable Retention Cable Flex Resistance Contact Resistance Insulation Resistance Dielectric Withstanding Voltage Thermal Shock Humidity High Temperature Life Shock Vibration Durability Hydrogen Sulfide Exposure Salt Spray* Sample Number 4 5 6 7 1 2 3 3.6.3 3.6.4 - - - X X X X X X 3.6.6 3.6.1 3.6.2 3.5.2 3.5.4 3.5.5 3.7.2 3.7.1 3.7.3 3.7.4 3.7.5 3.6.5 3.7.6 3.7.7 X X X X X - X X X X - X X X X X X - X X X X X X x X X X X X X X X X X 8 9 X - X - X - X X X X X X X X X X X X X X * This test not applicable to tin plated connectors. 4.4 Quality Conformance Inspection. Quality conformance inspection shall be performed on sample units produced with equipment and procedures normally used in production. 4.4.1 Copyright Sample. Six (6) of the largest population connectors shall be selected at random and subjected to quality conformance inspection. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION BUS-12-082 TITLE PAGE QuickieTM Connector System REVISION 17 of 20 F AUTHORIZED BY DATE 31 Jul 06 M.Barrios CLASSIFICATION UNRESTRICTED 4.4.2 Preparation of Samples. The various test samples shall be configured as shown in Table IV. TABLE IV - TEST SAMPLE DESCRIPTION Flexible Cable Sample Number Number of Contacts 1 2 3 4 5 6 2 2 2 2 2 2 4.4.3 x x x x x x 25 25 25 25 25 25 Strain Relief Yes No No Yes Yes No Latches Wire Size No No No No No No Type AWG 28 AWG 28 None AWG 28 AWG 28 AWG 30 Length Stranded Stranded - - Stranded Stranded Solid 254mm/10" 254mm/10" - - 254mm/10" 254mm/10" 254mm/10" Test Sequence. The sample connectors shall be subjected to the inspections specified in Table V in the order shown. TABLE V - QUALITY CONFORMANCE INSPECTION Examination or Test Sample Number Paragraph Total Mating Force Individual Contact Separation Force Cable Retention Cable Flex Resistance Contact Resistance Insulation Resistance Dielectric Withstanding Voltage Thermal Shock Humidity Durability Hydrogen Sulfide Exposure Salt Spray* 3.6.3 3.6.4 3.6.1 3.6.2 3.5.2 3.5.4 3.5.5 3.7.2 3.7.1 3.6.5 3.7.6 3.7.7 1 2 3 4 5 6 X X X X - X X - X X X X - X X X X X X X X X X X X X X X X X X X * This test not applicable to tin plated connectors. 4.4.4 Copyright Failures. If a connector fails to pass the quality conformance inspection, appropriate corrective action shall be taken on the materials or processes and additional sample units shall be subjected to the quality conformance inspection to verify the effectiveness of the action. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 18 of 20 AUTHORIZED BY F DATE M.Barrios 31 Jul 06 CLASSIFICATION UNRESTRICTED 4.4.5 4.5 Disposition of Sample Units. Sample units that have been subjected to the quality conformance inspection shall not be considered deliverable on the contract or purchase order. Acceptance Inspection Acceptance inspection shall consist of the examinations and inspections specified in Table VI. TABLE VI - ACCEPTANCE INSPECTION AQL Examination Visual & Mechanical Copyright Major Minor 1.0% 4.0% 4.5.1 Inspection Lot. An inspection lot shall consist of all connectors produced under essentially the same conditions and offered for inspection at one time. 4.5.2 Sampling Plan. Statistical sampling and inspection shall be in accordance with MIL-STD105 for General Inspection, Level II. The acceptable quality level (AQL) shall be as specified in Table VI. Major and minor defects shall be as defined in MIL-STD-105. 4.5.3 Rejected Lots. Rejected lots shall be reworked to correct the defects or screened to remove defective units and re-submitted for inspection. 4.5.4 Disposition of Sample Units. Sample units that have been subjected to the acceptance inspection shall be considered deliverable on the contract or purchase order. FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE BUS-12-082 PAGE QuickieTM Connector System REVISION 19 of 20 F AUTHORIZED BY DATE 31 Jul 06 M.Barrios CLASSIFICATION UNRESTRICTED REVISION RECORD REV PAGE A All 5 10 13 14 16 18 23 B All C 1-13 D EC # DATE 15773 11/10/88 V11791 06/28/91 Changed references for male and female to header and receptacle Deleted charts on pg. 4 and 7 Change 64 to 60 in 3.4.1.2 V13143 11/12/91 All Revised format to be consistent with GS-01-001, and change BERG, Dupont, etc. references to FCI. V01904 08/01/00 E 12 17 Add 3.6.6 to Page 12 Add 3.6.6 to Table III V03-1270 02/11/04 F All New FCI Logo Copyright DESCRIPTION Page 2 - change "Berg" to "DuPont" Remove "This product is pre-plated" Add metric equivalent Add metric equivalent Add sizes & metric equivalents Add "and Euro Qke" Remove 25 gm. and reference 3.64 only Add metric equivalent V06-0709 07/31/06 FCI Form E-3334 Rev E GS-01-001 PDM: Rev:F STATUS:Released Printed: Nov 28, 2010. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 66506-246 72454-016V 65823-081 65823-169 65863-195 66429-069 66506-019 69155-040 71918-120LF 66506-019LF 52601-G16-6LF 65863-197 65863-213 65863-270 66207-015 66429-169 75867-301LF 75869101LF 75869-105LF 65863-207 66506-032LF 66900-016LF 65823-073LF 66900-310LF 71918-150LF 66506002LF 66900-010LF 65863-075LF 65823-079LF 66900-240LF 71922-214LF 66900-250LF 66506-242LF 66506230LF 66900-230LF 65823-239LF 66900-116LF 65863-268LF 66506-053LF 71922-150LF 65863-081LF 65823085LF 65823-093LF 65823-091LF 65863-103LF 66900-126LF 66506-043LF 66506-050LF 65863-265LF 71918126LF 53612-S40-8LF 71918-106LF 66429-049 66429-103 66429-242 66506-049 66506-051 66506-078 66506109 66506-223 66506-231 66900-044 66900-114 66900-120 66900-134 66900-260 66900-314 66900-334 66900-340 66902-020 66902-140 66902-216 66902-226 66902-260 67916-187 69155-014 69155-020 66506-242 66506-043 65863-271 65863-091 65863-049 65863-079 65863-055 65863-067 65863-025 66902-240 66902220 65823-079 65823-067 66900-216 66900-226 52601-G10-4 66900-350 66429-061 66900-010 53611-G108LF 53612-G40-4LF 65823-081LF 65823-378LF