TP3465 TP3465 MICROWIRE(TM) Interface Device (MID) Literature Number: SNOS569 TP3465 MICROWIRE TM Interface Device (MID) General Description Features The MICROWIRETM Interface Device MID gives a general microprocessor (such as National Series 32000E processors, Intel 80C188, 80C86 or 80286, Motorola 6800 and 68000 family of processors) the ability to communicate efficiently with up to eight peripheral devices via the serial MICROWIRE interface. The MID causes each of the peripheral devices to appear to the mP as memory mapped locations, by performing all the data serialization and transfer protocols to and from the peripherals. Y Applications Y Y Y Y Y Y Y Y Y Y Y Y ISDN Terminal Adapters Digital Line cards (ISDN and Non ISDN) Analog Linecards using National COMBOE Interfacing to industry standard serial EEPROMs Interfacing to industry standard MICROWIRE peripheral devices such as Analog to Digital Converters, LCD drivers, clock generators Y Y Y Y Multiplexed and Non-multiplexed microprocessor bus compatible National/Intel and Motorola microprocessor bus compatible Microprocessor Clock (CKIN) up to 20 MHz MICROWIRE clock speeds up to 5 MHz Directly compatible with 8- and 16-bit MICROWIRE peripherals Commercial temperature range 0C to +70C TP3465 for 8 Chip Select output Memory mapped peripherals Programmable MICROWIRE Clock to communicate with devices of different speeds Operates as MICROWIRE bus master or slave 28-pin PLCC Package CMOS, Low Power Block Diagram TL/H/10803 - 1 FIGURE 1. MICROWIRE Interface Device MID COMBOE, Series 32000E and TRI-STATEE are registered trademarks of National Semiconductor Corporation. MICROWIRETM is a trademark of National Semiconductor Corporation. C1999 National Semiconductor Corporation TL/H/10803 TP3465 MICROWIRE Interface Device (MID) July 1999 Connection Diagrams 28-Pin PLCC TL/H/10803 - 3 Top View Order Number TP3465V See NS Package Number V28A FIGURE 2. MICROWIRE Interface Device MID TP3465 Pinouts Pin Description Pin No. 28 Pkg. Name Type Function VCC 28 I +5V Supply GND 14 I 0V CKIN 17 I Master Clock Input Used to Derive the SK Clock MICROWIRE Interface The MICROWIRE Interface consists of SK (clock out), SO (data out), SI (data in) and up to 8 chip select output lines. Pin No. 28 Pkg. Type SK 13 O SO 15 O/I Name SI 16 I CS0 -CS3 24-27 I/O CS4 CS7 6, 9, 20, 23 Function MICROWIRE clock output. MICROWIRE data output. Can also be used for MICROWIRE data input when communicating with special devices. See application section. MICROWIRE data input. Four input/output lines, normally used as outputs for chip selects to MICROWIRE peripherals I/O Four chip select lines accessible when using the Multiplexed bus mode. 2 MultiplexedMicroprocessorBus Interface The MULT/INT pin is sampled on power-up and, if LOW, the microprocessor bus format is assumed to be Multiplexed and the pin is considered an input pin to indicate Multiplexed bus format. The pin has an internal pull-up and thus if pin is left floating, it will be considered as in Non-multiplexed mode. The interface consists of an eight bit multiplexed Address/Data microprocessor bus (only the A0, A1, A2 and A3 address lines are decoded), and six control lines (CE, RST, AS/MI, RD/DS, WR/(R/W) and the MULT input) which should be tied LOW. Pin No. 28 Pkg. Name AD0 -AD7 CE Type 1, 2, 3, 4, 5, 7, 8, 10 I/O 19 I Function Address/Data bus. Transfers addresses and data between the microprocessor and the MID. Chip Enable. A LOW on this signal selects the MID for a Read/Write operation. WR/ R/W 11 I Write or Read-Write direction. This signal indicates a Write operation or Read/Write direction signal. RD/DS 12 I Read or Data Strobe. With an Intel mP this signal indicates a Read operation (active low polarity signal) or with a Motorola mP, a Data strobe (active high polarity signal). AS/MI 21 I Address Latch Enable or Address Strobe. A HIGH on this line indicates an address on the external A/D bus. When MULT e 1 (non-multiplexed bus), the pin indicates the type of bus, MI e 1 for NSC/Intel format and MI e 0, for Motorola format. RST 22 I The RST is the master Reset input, when LOW forces the device in the RESET condition (same as Power-onReset). MULT/ INT 18 I Multiplexed Bus input or INTerrupt output. It is internally pulled HIGH to indicate a Non-Multiplexed bus format and needs to be pulled LOW externally to indicate the Multiplexed bus format. Non-Multiplexed Microprocessor Interface The MULT/INT pin is sampled on power-up and, if not LOW, the microprocessor bus format is assumed to be Non-multiplexed. This interface consists of a four-bit Address bus, an eight-bit Data bus and six control lines (CE RST, AS/MI, RD/DS, WR/(R/WR) and the INT signal if enabled). Name Pin No. 28 Pkg. Type Function A0 -A3 6, 9, 20, 23 I Address bus. These 4 pins (accessible in the 28-pin package) are used to address the 16 registers. D0 - D7 1, 2, 3, 4, 5, 7, 8, 10 I/O CE 19 I Chip Enable. A LOW on this signal selects the MID for a Read/Write operation. WR/ (R/W) 11 I Write or Read-Write direction. This signal indicates a Write operation or Read/Write direction signal. RD/DS 12 I Read or Data Strobe. With an Intel mP this signal indicates a Read operation (active low polarity signal) or with a Motorola mP, a Data Strobe (active high polarity signal). AS/MI 21 I Address Latch Enable or Address Strobe. A HIGH on this line indicates an address on the external A/D bus. When MULT e 1 (non-multiplexed bus), the pin indicates the type of bus, MI e 1 for NSC/Intel format and MI e 0 for Motorola format. Data bus for data transfer between the microprocessor and the MID. 3 Non-Multiplexed Microprocessor Interface (Continued) The MULT/INT pin is sampled on power-up and, if not LOW, the microprocessor bus format is assumed to be Non-multiplexed. This interface consists of a four-bit Address bus, an eight-bit Data bus and six control lines (CE RST, AS/MI, RD/DS, WR/(R/WR) and the INT signal if enabled). Pin No. 28 Pkg. Type RST 22 I The RST is the master Reset input; when LOW, it forces the device in the RESET condition (same as Power-on-Reset). MULT/ INT 18 I O Multiplexed Bus input or INTerrupt output. It is internally pulled HIGH to indicate a Non-multiplexed bus format and the pin can be an INT output pin if enabled by setting the Inten bit in the CKR register. INT pulls low to indicate the completion of a MICROWIRE transfer operation. Name Function Functional Description The block diagram of the MICROWIRE Interface Device (MID) is shown in Figure 1 . It essentially consists of a very flexible microprocessor bus interface, a serial MICROWIRE interface and a Chip Select (output) port. Internally it contains a programmable clock divider to derive the MICROWIRE clock speed from a system clock. MICROWIRE COMMUNICATION MODES The MID provides a MICROWIRE port to the main processor having two modes of operation with the MICROWIRE peripherals; software-controlled chip select and hardware-generated chip select modes. In the first scheme, besides the 2 data byte registers, there is a third register which maps directly with the output CS Chip Selects pins, which there eight pins for this function in the TP3465 28-pin package . The software in the microprocessor then writes to the CS register to select and deselect individual bits (corresponding to pins). In the second scheme, the CS pins are activated by a hardware state machine when triggered, by accessing the data registers through other address locations (see section on Register description). In this case the hardware will activate the chip select pin, send the appropriate number of MICROWIRE data bits (8 or 16 ) and then deselect the pin. This enhanced mode of communication allows the MICROWIRE peripheral devices to appear as if I/O mapped in the microprocessor's memory space. MICROPROCESSOR INTERFACE The Microprocessor bus interface supports both National/ Intel and Motorola bus formats in the Multiplexed and Nonmultiplexed bus modes. The MULT/INT pin is sampled on power-up and, if LOW, the microprocessor bus format is assumed to be Multiplexed and the pin is considered an input pin to indicate Multiplexed bus format. The pin is internally pulled HIGH. Upon sampling, if the pin is not LOW, the bus format is assumed to be Non-multiplexed. The microprocessor interface supports multiplexed Address/Data Formats for the Intel 8088/80188 and Motorola 6803 families to work in 8-bit mode. Non-multiplexed busses of the National 32000, Intel 80286 and Motorola 68000, series processors and similar are supported in the TP3465 28pin part. Four address lines allow access to all MID registers. The MID incorporates a flexible bus interface logic to support the different address and data strobes required by the different bus formats. The timing specifications are shown in a later section. The following table shows microprocessor bus control pin functions: MID Pin AS/MI NSC/Intel Bus CONTROL AND DATA REGISTERS There are 6 control registers (PD, MWM, SKP, SKR, ST and CS), and 1 set of Data registers (First MICROWIRE Byte FMB and Second MICROWIRE Byte SMB) for data communication to MICROWIRE devices. In normal mode, the Chip select pins CS0 -C7 are controlled (via the CS register) by software and data is transferred via the FMB and SMB registers located at address 01h and 00h (see Table I). Eight additional addresses (FMBD0 -7) access the same data register (FMB) but provide additional information to an internal state machine which drives appropriate chip select pins (e.g., FMBD0 at address 02h controls CS0 pin, FMBD1 at address 03h controls CS1 pin etc.). There is only 1 set of Data registers (FMB and SMB) which handle the MICROWIRE communication. This latter method of allocating special addresses to provide pin-select information facilitates an enhanced MICROWIRE interface to the host processor. Table I summarizes the Control and Data Registers and the addresses at which they are accessed. Motorola Bus MUXed Non-MUXed MUXed Non-MUXed ALE MI e 1 AS MI e 0 RD/DS RD RD DS DS WR/(R/W) WR WR (R/W) (R/W) See Figure 7 for connection of the AS and DS signals to Motorola mPs. 4 Functional Description (Continued) TABLE I. Control and Data Registers Address Register Bit7 00h Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 SMB d7 d6 d5 d4 d3 d2 d1 d0 01h FMB d7 d6 d5 d4 d3 d2 d1 d0 02h FMBD0 d7 d6 d5 d4 d3 d2 d1 d0 03h FMBD1 d7 d6 d5 d4 d3 d2 d1 d0 04h FMBD2 d7 d6 d5 d4 d3 d2 d1 d0 05h FMBD3 d7 d6 d5 d4 d3 d2 d1 d0 06h FMBD4 d7 d6 d5 d4 d3 d2 d1 d0 07h FMBD5 d7 d6 d5 d4 d3 d2 d1 d0 08h FMBD6 d7 d6 d5 d4 d3 d2 d1 d0 09h FMBD7 d7 d6 d5 d4 d3 d2 d1 d0 0Ah CS cs7 cs6 cs5 cs4 cs3 cs2 cs1 cs0 0Bh SKP skp7 skp6 skp5 skp4 skp3 skp2 skp1 skp0 0Ch MWM mwm7 mwm6 mwm5 mwm4 mwm3 mwm2 mwm1 mwm0 0Dh SKR inten soi ms 0 0 div2 div1 div0 0Eh ST uwdone 0 0 0 0 0 0 0 0Fh PD pd7 pd6 pd5 pd4 pd3 pd2 pd1 pd0 MWMMICROWIRE Mode Register: W Register RESET condition is 00hex PDPin Definition Register: W Register RESET condition is FFhex (all pins as Inputs) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 pd7 pd6 pd5 pd4 pd3 pd2 pd1 pd0 Bit7 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 skp7 skp6 skp5 skp4 skp3 skp2 skp1 skp0 div1 div0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 SK Ratio SK SK SK SK SK SK SK SK e e e e e e e e CKIN CKIN/2 CKIN/4 CKIN/8 CKIN/16 CKIN/32 CKIN/64 CKIN/128 Bit3 Bit2 Bit1 Bit0 SKRMICROWIRE Clock (SK) Rate Register: W Register skp 0 - 7 bits set the polarity of the SK MICROWIRE clock when communicating with device connected to each of the pins CS0 -7. For example skp0 e 0, normal MICROWIRE mode (i.e., SO data output on negative edge of SK clock) when sending data to device controlled by CS0 pin; skp1 e 1, NSC COMBO II clock format for device controlled by CS1 (i.e., SO data output on the positive edge of SK clock). div2 Bit4 mwm7 mwm6 mwm5 mwm4 mwm3 mwm2 mwm1 mwm0 SKPMICROWIRE Clock (SK) Polarity: W Register RESET condition is 00hex (Normal MICROWIRE clock) Bit6 Bit5 mwm0 - 7 bits specify whether 8 or 16 clocks are generated for devices connected to CS0 - 7 pins. For example mwm1 e 1, 16 clocks will be generated for device controlled by CS1, (16 data bits will be shifted out and 16 data bits will be strobed in); mwm0 e 0, 8 clocks will be generated for device controlled by CS0 (8 data bits will be shifted out and strobed in). pd0 - 7 bits configure the CS0-7 pins as inputs or outputs. For example pd0 e 1, sets the CS0 pin as an input; pd0 e 0, sets CS0 pin as an output. Upon chip RESET, the pd0 -7 bits are set to 1. Bit7 Bit6 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 inten soi ms 0 0 div2 div1 div0 The 3 bits div0 - 2 give the divide-by value for deriving the SK clock output rate from the CKIN. The maximum CKIN rate is 20 MHz, and the slowest MICROWIRE peripheral works at 256 kHz. Table 2 below gives the division ratios and some examples: e.g., CKIN e 5 MHz e.g., CKIN e 20 MHz SK e 5 MHz SK e 2.5 MHz e 1.25 MHz e 625 kHz e 312.5 kHz e 156.25 kHz e 78.125 kHz e 39.06 kHz SK e 5 MHz e 2.5 MHz e 1.25 MHz e 625 kHz e 312.5 kHz e 156.25 kHz TABLE 2. SK Clock Rate Control 5 Functional Description (Continued) The uwdone bit in the ST register can be connected to the INT pin of the MID to alert the host processor when MICROWIRE transmission is completed by setting the inten bit in this SKR register. The INT pin will only be functional as an interrupt in the Non-multiplexed bus mode in the 28-pin TP3465 device. The soi bit configures the SO pin to be output (soi e 0) or input (soi e 1). This bit function is used to perform a Read operation on a device such as NSC TP3071 COMBO II because the TP3071 sends data back on the SO pin. When soi e 1, the SO pin functions as the SI input pin, internally, and feeds the data registers. See applications diagrams and software procedures for more details. The ms bit configures the MID device as a Master of MICROWIRE (ms e 0) or Slave of MICROWIRE (ms e 1). MICROWIRE Slave mode is described and illustrated in the applications section. FMBFirst MICROWIRE Byte: R/W Register Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 cs7 cs6 cs5 cs4 cs3 cs2 cs1 cs0 uwdone 0 Bit5 0 Bit4 0 Bit3 0 Bit2 0 Bit4 Bit3 Bit2 Bit1 Bit0 d5 d4 d3 d2 d1 d0 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 d7 d6 d5 d4 d3 d2 d1 d0 FMBD0First MICROWIRE Byte Dev0: R/W Register STMICROWIRE Status Register: R Register RESET Condition, Read 80 Hex Bit6 Bit5 d6 The SMB and the FMB data registers are used to communicate to any MICROWIRE device 0 -7 (connected to pins CS0 -7) when controlling the chip select lines via CS register (using software). The MICROWIRE parameters for this mode of operation are defined by the parameters for device 7, i.e., skp7 in SKP register, and mwm7 in MWM register. So when communicating with peripherals requiring different formats, the skp7 and mwm7 bits may need to be re-configured before sending data to each of these devices. Example of communication to 8-bit and 16-bit peripherals are described below: Example 1: Communicating with an 8-bit MICROWIRE peripheral at CS1: Set the skp7 bit to 0 (normal MICROWIRE polarity), and set the mwm7 to 0 for 1 byte operation. Set cs1 bit to 0 to select the device. Write the data into the FMB byte location so it will be shifted out after the trailing edge of the Write strobe signal. At the end of the MICROWIRE transmission set the cs1 bit to 1 to de-select the device. The 8-bit STATUS from the peripheral is read from the FMByte location. Example 2: Communicating with a 16-bit MICROWIRE peripheral at CS3: MICROWIRE protocol specifies that the Most Significant Bit is transmitted first. Thus the HIGH byte of data becomes the First MICROWIRE Byte to be sent out. Set the skp7 bit to 0 (normal MICROWIRE polarity), and set the mwm7 to 1 for 2 byte operation. Set cs3 bit to 0 to select the device. Write the LOW data byte in the SMB register and then write the HIGH data byte into the FMB byte location. All 16 data bits are shifted out after the trailing edge of the Write strobe for the FMB register. At the end of the MICROWIRE transmission set the cs3 bit to 1 to deselect the device. The 16-bit STATUS from the peripheral is read from the FMB (HIGH data byte) and the SMB (LOW data byte) locations. The cs0 -7 bits control the 8, CS input/output port pins. However, only the cs0- 3 control bits are available in the TP3465 device when used in the non-multiplexed bus format. In the multiplexed bus format in TP3465, all 8 CS pins are accessible. Writing to this register will affect the pins (configured as outputs in PD register) directly. Similarly, the state of the pins which are configured as inputs in the PD registers can be Read via the same (CS) register. When reading the pins designated as outputs, the bits will have a ``1'' condition. Writing to bits corresponding to input pins will have no effect on the pins. The state of an output chip select pin may also be controlled by the chip hardware state machine if the user writes to the FMBD0 - 7 registers. The hardware can only bring the appropriate pin LOW for the duration of the MICROWIRE transfer and will attempt to set it HIGH at the end of the transfer. If the user has, however, set this pin to be LOW by writing to this register, it will over-ride the action of the hardware and the pin will remain LOW. Thus the user must write a ``1'' in the bits that will be controlled by hardware, and the pins must be set as outputs in the PD register. Bit7 Bit6 d7 SMBSecond MICROWIRE Byte: R/W Register CSChip Select Port Register: R/W Register RESET condition, CS pins are inputs and the register contains the state of these pins. Bit7 Bit7 Bit1 0 Bit0 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 d7 d6 d5 d4 d3 d2 d1 d0 There is only one set of data registers (FMB and SMB) which handle the MICROWIRE data communication. The FMBD0 address accesses the data register FMB but also provides information for the internal state machine to control the CS0 pin. The MICROWIRE parameters for device 0 are indicated by the state of bits skp0 and mwm0, etc. 0 The uwdone bit (read only) in the ST register can be polled by the software to determine the end of the MICROWIRE transmission (uwdone e 1). uwdone e 0 during transmission. 6 MICROWIRE SLAVE MODE The MID can be set to work in MICROWIRE Slave mode by setting the ms bit to 1. The MICROWIRE clock from the master is connected to the CKIN pin of this MID device. The SK output is ignored. Normally the SO pin is in TRI-STATE condition and, while the uwdone bit is 1, any CKIN clock inputs are ignored. Writing to the FMB register causes the most significant bit to be output immediately to the SO pin and the uwdone bit is reset to 0 by hardware. The SK clock input is then enabled to clock data into SI and out of SO. After receiving SK clock pulses; either 8 (mwm7 e 0) or 16 bits (mwm7 e 1), the uwdone bit is set to 1 by hardware. The SO pin is then set to TRI-STATE condition. Note that when using the FMB and SMB registers, the communication mode is determined by the parameters of channel 7 (mwm7 and skp7). FMBD0 - 7 addresses are not used in the slave mode. The CS register, however, can be used as a general I/O port control register. See applications section for an example of the Slave operation (Figure 6) . Functional Description (Continued) Example 1: Communicating with 8-bit peripheraldevice 0: The mwm0 bit must be set to 0. Write the MICROWIRE data in to the FMBD0 address. The 8-bit data is then shifted out after the trailing edge of the write pulse. The Chip Select (CS0) is automatically activated (LOW) and deactivated (HIGH) by hardware before and after the data transfer (see timing diagrams). The 8-bit STATUS from the peripheral is read from the FMBD0 byte location. Example 2: Communicating with 16-bit peripheraldevice 0: The mwm0 bit must be set to 1. Write the LOW byte of MICROWIRE data into the SMB data register and then write the HIGH byte in to the FMBD0 address. The 16-bit data is then shifted out after the trailing edge of the write strobe signal for this FMBD0 address. The Chip Select 0 (CS0) pin is automatically activated (LOW) and deactivated (HIGH) by hardware before and after the data transfer (see timing diagrams). The 16-bit STATUS from the peripheral is read from the FMBD0 (HIGH data byte) and the SMB (LOW data byte) locations. MICROWIRE BUS FORMATS MID supports devices which implement either of the two MICROWIRE bus formats; a 3-pin format and a 4-pin format. Figure 3 shows a MID connected to devices supporting each of these formats. The standard 4-pin format consists of the CCLK clock pin, CO and CI as the data out and data in pins, and CS to select the MICROWIRE peripheral. ISDN transceivers and other intelligent peripherals also have an INTerrupt signal from the peripheral to the local microprocessor. NSC MICROWIRE devices with this 4-pin format include ISDN transceivers, COMBO II, LCD display drivers and EEPROMs. There are, however, some MICROWIRE peripherals (e.g., TP3071 COMBO II, and some EEPROMs) which support a 3-pin bus format because of package pin limitations. The format consists of the CCLK clock signal, a bi-directional data signal CO/CI, and a CS chip select signal. The direction of the data transferred on the CO/CI pin is determined by a protocol between the Master and the Slave of the MICROWIRE bus. For example, the TP3071 implements a two-byte protocol. The first byte into the TP3071 indicates a Read or a Write operation and thus defines the direction of the next byte to the device. FMBD1First MICROWIRE Byte Dev1: R/W Register Same function as FMBD0 except this refers to Device 1 and Chip Select 1 (CS1). FMBD2First MICROWIRE Byte Dev2: R/W Register Same function as FMBD0 except this refers to Device 2 and Chip Select 2 (CS2). FMBD3First MICROWIRE Byte Dev3: R/W Register Same function as FMBD0 except this refers to Device 3 and Chip Select 3 (CS3). FMBD4First MICROWIRE Byte Dev4: R/W Register Same function as FMBD0 except this refers to Device 4 and Chip Select 4 (CS4). FMBD5First MICROWIRE Byte Dev5: R/W Register Same function as FMBD0 except this refers to Device 5 and Chip Select 5 (CS5). FMBD6First MICROWIRE Byte Dev6: R/W Register Same function as FMBD0 except this refers to Device 6 and Chip Select 6 (CS6). FMBD7First MICROWIRE Byte Dev7: R/W Register Same function as FMBD0 except this refers to Device 7 and Chip Select 7 (CS7). Software Driver Procedures This section describes the steps for software driver routines to communicate with different MICROWIRE devices (8-bit, 16-bit, or more) and those supporting the 3-pin or 4-pin MICROWIRE bus formats. MICROWIRE Master/Slave Modes MICROWIRE MASTER MODE The primary application for MID is as a master of MICROWIRE bus (ms bit in CKR register set to 0), and as such it provides the SK clock out to the peripheral devices. It transmits data on the SO pin and receives data on the SI pin. The CS0 - 7 pins are used as chip select pins for the peripherals and have a predefined relationship with the SK clock output. Writing to the FMB pin causes the most significant bit to be output immediately to the SO pin, and the uwdone bit is automatically reset to 0. Upon completion of transfer of either 8 bits (mwm7 e 0) or 16 bits (mwm7 e 1), the uwdone bit is set to 1. The SO pin is then set to the TRISTATEE condition. Note that when using the FMB and SMB registers, the communication mode is determined by the parameters for channel 7 (mwm7 and skp7). INITIALIZATION 1. Write to PD (Pin Definition) register to set the desired chip select control pins (CS0 - 7) as outputs. (All CS pins are set to inputs on chip RESET.) 2. Write to SKP (SK polarity), to select the polarity of the SK clock for each of the MICROWIRE devices connected to CS0 - 7 pins. 3. Write to MWM (MICROWIRE Mode) register to select whether 8- or 16-bit devices are attached to the CS0 - 7 pins. Devices needing more than 16-bits may still be configured as 8-bit mode (if multiple of 8) or 16-bit mode (if multiple of 16 bits). 7 b. Data transfer options: i. Set cs1 bit to 0, write HIGH byte to FMB, wait until uwdone bit is set to 1 by hardware. Set soi bit to 1. Write dummy LOW byte (e.g., 00h) to FMB, wait until uwdone bit is set to 1 by hardware. Read STATUS from FMB address. Set soi to 0 and cs1 to 1. Software Driver Procedures (Continued) 4. Write to SKR to set the div bits to support the fastest SK clock rate supported by the peripherals. Set inten e 1 if the uwdone status is to set an INTerrupt to the host processor (available only in the Non-multiplexed bus implementation of TP3465, 28-pin package). The ms and the soi bit are set to 0 upon power up and indicate that the MID is in MICROWIRE Master mode, with SO as an output pin as normal. SENDING DATA TO PERIPHERALS (Normal Mode) Assume sending 16-bit data to a MICROWIRE based device connected to any one of CS0 to CS7. 1. Write to CS (Chip Select) register and reset the appropriate bit and thus activate the corresponding CS pin. 2. Write LOW byte data to SMB (Second MICROWIRE Byte) register and then HIGH byte data to FMB (First MICROWIRE Byte) register. 3. Read the ST (Status) register and stay in a loop until uwdone bit is set. 4. Write to CS register and set the bit to deactivate the appropriate chip select pin. OR ii. Write HIGH byte to FMBD1, wait until uwdone bit is set to 1 by hardware. Set soi bit to 1. Write a dummy LOW byte (e.g., 00h) to FMBD1 and wait until uwdone bit is set to 1 by hardware. Read STATUS from FMBD1 address. Set soi bit to 0. Applications The versatile TP3465 MICROWIRE Interface Device can be used in a number of applications involving MICROWIRE peripheral devices that need to be controlled using a standard microprocessor which only has a parallel bus structure. ISDN TERMINAL ADAPTER The MID can be used in ISDN terminal adapters (see Figure 4 ) interfacing to ISDN components such as TP3420 SID, as well as non-ISDN components such as LCD display drivers (e.g., COP470) and serial EEPROMs (COP494). In this application the MID signals SK, SO and SI are bussed to all peripheral devices. The device chip selects control lines a total of 8 in the 28-pin package are individually connected to each of the devices. Status Interrupt from the peripherals such as SID are connected directly to the main processor. SENDING DATA TO PERIPHERALS (Hardware Assisted Chip Select) Assuming sending 16-bit data to dev3 connected to CS3 pin. 1. Write LOW byte data to address SMB and then HIGH byte data to FMBD3. 2. Read the ST register and stay in a loop until uwdone bit is set. ANALOG OR DIGITAL LINECARDS The MID can also be used in analog and digital (ISDN and Non-ISDN) linecard applications (see Figure 5 ). Up to 8 MICROWIRE peripheral devices (TP3070 COMBO II, or TP3420 SIDs, TP3410 UIDs or TP3401 DASLs) can be connected to one MID device. The Interrupts from the transceivers may be wire-ORed and fed into one interrupt line of the main processor, in which case all the devices will need to be polled after an interrupt. The efficient interface between the MID and microprocessor allows this process to be accomplished with minimum overhead. In a given application, if any of the chip select pins are not used to perform chip select for peripherals, then it may be used as a general purpose input/output pin under software control. Communicating with an NSC TP3071 COMBO II Type Device The NSC TP3071 COMBO II device has a modified MICROWIRE port. It shares a single pin (called CO/CI) for incoming and outgoing data. The MID's SO pin may be tied to this pin, as shown in Figure 3 , and the following steps are followed to Read from and Write to this device. Assume that the chip select for TP3071 is connected to CS1 pin. TP3071 Write Operation: a. Initialization states: skp1 e 1, mwm1 e 1, and soi e 0 b. Data transfer options: i. Set cs1 bit to 0, write LOW byte to SMB, and HIGH byte to FMB and then set cs1 bit to 1 after uwdone bit is set to 1. MID SUPPORTING MASTER AND SLAVE MICROWIRE OPERATION The MICROWIRE serial data bus is often used as a means of inter-processor communication. The MID may be used either as the Master of the MICROWIRE clock SK or as a Slave to the SK clock fed via CKIN pin. Figure 6 shows an application in which two general microprocessors communicate with each other over the MICROWIRE bus. At the same time other peripherals are also connected to the serial bus. External handshaking between the two processors is required before the MICROWIRE Byte data transfer is executed by the master of the MICROWIRE bus. OR ii. Write LOW byte to SMB, and HIGH byte to FMBD1. TP3071 Read Operation: a. Initialization states: skp1 e 1, mwm1 e 0, and soi e 0. 8 Applications (Continued) TL/H/10803 - 15 FIGURE 3. MID, Two Types of Microwire Formats; 3-Pin (e.g., TP3071 COMBO II) and 4-Pin (e.g., TP3420, SID) TL/H/10803 - 4 FIGURE 4. MID, TERMINAL EQUIPMENT Application The nomenclature for MICROWIRE signal names is as follows: MICROWIRE controllerSK (clock), SO (data out), SI (data in) MICROWIRE peripheralCCLK (clock), CO (data out), CI (data in). 9 Applications (Continued) TL/H/10803 - 5 FIGURE 5. MID, LINECARD ApplicationDigital (ISDN/Non-ISDN) or Analog 10 Applications (Continued) The nomenclature for MICROWIRE signal names is as follows: MICROWIRE controllerSK (clock), SO (data out), SI (data in) MICROWIRE peripheralCCLK (clock), CO (data out), CI (data in). TL/H/10803 - 6 FIGURE 6. Example of MID in Master or Slave MICROWIRE Operation TL/H/10803 - 16 Note: For TP3465, the AS (Address Strobe) and DS (Data Strobe) are active high polarity signals. For non-multiplexed busses, AS = 0. FIGURE 7. MID, Connecting to Motorola mPs. 11 Device Electrical Characteristics Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. VCC to GND 7V Input Voltage DC Input Current Storage Temperature Range Lead Temperature (Soldering, 10 Sec.) ESD Rating b 0.3V to VCC a 0.3V II g 50 mA b 65 C to a 150 C 300 C t 1500V Electrical Characteristics Unless otherwise noted, limits in BOLD characters are electrical testing limits at VCC e 5.0V and TA e a 25 C. All other limits are assured by correlation with other production tests and/or product design and characterization for VCC e 5.0V g 5% and TA e 0 C to a 70 C. All signals are referenced to GND. Symbol Parameter Limits Conditions Min VIL Input Low Voltage All Inputs VIH Input High Voltage All Inputs VOL Output Low Voltage CS0 - 7: IOL e 1 mA SK, SO: IOL e 4 mA AD(7:0): IOL e 2 mA VOH Output High Voltage CS0 - 7: IOH e 1 mA SK, SO: IOH e 4 mA AD(7:0): IOH e 2 mA Units Max 0.8 2.0 V V 0.4 2.4 V V IIH High Level Input Current All Inputs, GND k VIN k VCC b 10 IIL Low Level Input Current All Inputs a 10 mA IOZ Output Current in High-Z AD(7:0), SO g 20 mA ICC Dynamic Supply Current CKIN e SK e 1 MHz CKIN e SK e 20 MHz 0.7 4 mA 12 mA Timing Characteristics This section contains timing diagrams for the microprocessor bus interface, MICROWIRE port interface and the Control and Clock timings relationships. Timing characteristics are derived from worst-case simulations plus guardbanding. Production testing is limited to device functionality. NSC/Intel Bus Format MULTIPLEXED MICROPROCESSOR BUS TL/H/10803 - 7 NON-MULTIPLEXED MICROPROCESSOR BUS TL/H/10803 - 8 Symbol Parameter Conditions Min Max Units tWASH Width, Address Strobe High 20 ns tSAAS Setup, Address to Address Strobe 10 ns tHASA Hold, Address Strobe Low to Address 10 ns tHASR Hold, Address Strobe to Read Strobe 10 ns tDRD Delay, Read Low to Data tHRD Hold, Read High to Data 5 tWRL Width, Read Strobe Low 20 ns tSDW Setup, Data to Write High 30 ns tHWD Hold, Write High to Data 10 ns tWWL Width, Write Strobe Low 20 ns tSAR Setup, Address to Read Low Non-Muxed, MI e 1 10 ns tHRA Hold, Read High to Address Non-Muxed, MI e 1 10 ns tSAW Setup, Address to Write Low Non-Muxed, MI e 1 10 ns tHWA Hold, Write High to Address Non-Muxed, MI e 1 10 ns 100 pF Load 13 70 ns 40 ns Motorola Bus Format MULTIPLEXED MICROPROCESSOR BUS TL/H/10803 - 9 NON-MULTIPLEXED MICROPROCESSOR BUS TL/H/10803 - 10 Note: For TP3465 MID, the AS (Address Strobe) and DS (Data Strobe) are active high polarity signals. For Non-multiplexed busses AS = 0. SeeFigure7 for connection diagram. Symbol Parameter Conditions Min Max Units tWASH Width, Address Strobe High 20 ns tSAAS Setup, Address to Address Strobe 10 ns tHASA Hold, Address Strobe Low to Address 10 ns tHASDS Hold, Address Strobe to Data Strobe 10 tDDSD Delay, Data Strobe Low to Data (Read) tHDSD Hold, Data Strobe High to Data 5 tWDSL Width, Data Strobe Low 20 ns tSDDS Setup, Data to Data Strobe High (Write) 30 ns tSRWDS Setup, R/W Strobe to Data Strobe 10 ns tHDSRW Hold, Data Strobe to R/W 10 ns 10 ns 10 ns 100 pF Load tSADS Setup, Address to Data Strobe Low Non-Muxed, MI e 0 tHDSA Hold, Data Strobe High to Address Non-Muxed, MI e 0 14 ns 70 ns 40 ns MICROWIRE Timing Diagrams Symbol Parameter Conditions Min Max Units fCKIN CKin Frequency 20 MHz fSK SK Frequency 5 MHz tSKD SK Clock Duration 200 ns tSKH SK High Duration 70 ns tSKL SK Low Duration tRSK Rise Time, SK 100 pF Load 30 tFSK Fall Time, SK 100 pF Load 30 tSISK Setup Time, SI Valid to SK Edge 20 tHSKI Hold Time, SK High to SI Invalid 20 tDSKO Delay, SK Edge to SO Data Valid Output 20 ns tDSKZ Delay, Last SK to SO TRI-STATE 30 ns tDWOV Delay, WR to SO Valid 50 ns 70 FMB or FMBD0 - 7 ns ns ns ns ns MICROWIRE Timing for 1 Byte Transfer TL/H/10803 - 11 MICROWIRE Timing for 2 Byte Transfers TL/H/10803 - 12 15 Control Interface Timing Relationships Symbol Parameter Conditions tDWCSA Delay, Write Strobe to CS Asserted Auto Mode tDCSSKA Delay, CS Active to first SK Edge Auto Mode Min 0.5 SK b 50 ns tDSKCSA Delay, Last SK Edge to CS Inactive CS Load e 10 pF; SK Load e 50 pF Auto Mode tDWCSS Delay, Write Strobe (CS Register) to CS Asserted Software tDCSN Delay, CS High to INT Low tDRDN Delay, RD Low to INT High ST Register 2.8 Max Units 2 SK Cycle 0.5 SK ns 7.3 ns 30 ns 50 ns 80 ns TL/H/10803 - 13 16 TP3465 MICROWIRE Interface Device (MID) Physical Dimensions inches (millimeters) (Continued) Plastic Chip Carrier (V) Order Number TP3465V NS Package Number V28A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated