ADC14DS105 ADC14DS105 Dual 14-Bit, 105 MSPS A/D Converter with Serial LVDS Outputs Literature Number: SNAS380E ADC14DS105 Dual 14-Bit, 105 MSPS A/D Converter with Serial LVDS Outputs General Description Features The ADC14DS105CISQ and ADC14DS105AISQ are highperformance CMOS analog-to-digital converters capable of converting two analog input signals into 14-bit digital words at rates up to 105 Mega Samples Per Second (MSPS). The digital outputs are serialized and provided on differential LVDS signal pairs. Both parts provide excellent performance, however, the ADC14DS105AISQ offers higher SFDR. These converters use a differential, pipelined architecture with digital error correction and an on-chip sample-and-hold circuit to minimize power consumption and the external component count, while providing excellent dynamic performance. The ADC14DS105 may be operated from a single +3.0V or 3.3V power supply. A power-down feature reduces the power consumption to very low levels while still allowing fast wake-up time to full operation. The differential inputs accept a 2V full scale differential input swing. A stable 1.2V internal voltage reference is provided, or the ADC14DS105 can be operated with an external 1.2V reference. The selectable duty cycle stabilizer maintains performance over a wide range of clock duty cycles. A serial interface allows access to the internal registers for full control of the ADC14DS105's functionality. The ADC14DS105 is available in a 60-lead LLP package and operates over the industrial temperature range of -40C to +85C. Clock Duty Cycle Stabilizer Single +3.0V or 3.3V supply operation Serial LVDS Outputs Serial Control Interface Overrange outputs 60-pin LLP package, (9x9x0.8mm, 0.5mm pin-pitch) Key Specifications For ADC14DS105A Resolution Conversion Rate SNR (fIN = 240 MHz) SFDR (fIN = 240 MHz) Full Power Bandwidth Power Consumption 14 Bits 105 MSPS 70.5 dBFS (typ) 83 dBFS (typ) 1 GHz (typ) 1 W (typ) Applications High IF Sampling Receivers Wireless Base Station Receivers Test and Measurement Equipment Communications Instrumentation Portable Instrumentation Connection Diagram 20211201 (c) 2007 National Semiconductor Corporation 202112 www.national.com ADC14DS105 Dual 14-Bit, 105 MSPS A/D Converter with Serial LVDS Outputs December 11, 2007 ADC14DS105 Block Diagram 20211202 Ordering Information www.national.com Industrial (-40C TA +85C) Package ADC14DS105AISQ 60 Pin LLP (offers higher SFDR) ADC14DS105CISQ 60 Pin LLP ADC14DS105LFEB Evaluation Board for input frequency < 70MHz 2 ADC14DS105 Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit Description ANALOG I/O 3 13 VINA+ VINB+ 2 14 VINAVINB- 5 11 VRPA VRPB 7 9 VCMOA VCMOB 6 10 VRNA VRNB 59 VREF 29 LVDS_Bias Differential analog input pins. The differential full-scale input signal level is 2VP-P with each input pin signal centered on a common mode voltage, VCM. These pins should each be bypassed to AGND with a low ESL (equivalent series inductance) 0.1 F capacitor placed very close to the pin to minimize stray inductance. An 0201 size 0.1 F capacitor should be placed between VRP and VRN as close to the pins as possible, and a 1 F capacitor should be placed in parallel. VRP and VRN should not be loaded. VCMO may be loaded to 1mA for use as a temperature stable 1.5V reference. It is recommended to use VCMO to provide the common mode voltage, VCM, for the differential analog inputs. Reference Voltage. This device provides an internally developed 1.2V reference. When using the internal reference, VREF should be decoupled to AGND with a 0.1 F and a 1F, low equivalent series inductance (ESL) capacitor. This pin may be driven with an external 1.2V reference voltage. This pin should not be used to source or sink current. LVDS Driver Bias Resistor is applied from this pin to Analog Ground. The nominal value is 3.6K DIGITAL I/O 18 28 19 CLK The clock input pin. The analog inputs are sampled on the rising edge of the clock input. Reset_DLL Reset_DLL input. This pin is normally low. If the input clock frequency is changed abruptly, the internal timing circuits may become unlocked. Cycle this pin high for 1 microsecond to re-lock the DLL. The DLL will lock in several microseconds after Reset_DLL is asserted. OF/DCS This is a four-state pin controlling the input clock mode and output data format. OF/DCS = VA, output data format is 2's complement without duty cycle stabilization applied to the input clock OF/DCS = AGND, output data format is offset binary, without duty cycle stabilization applied to the input clock. OF/DCS = (2/3)*VA, output data is 2's complement with duty cycle stabilization applied to the input clock OF/DCS = (1/3)*VA, output data is offset binary with duty cycle stabilization applied to the input clock. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. 3 www.national.com ADC14DS105 Pin No. 57 20 27 47 48 45 44 43 42 www.national.com Symbol Equivalent Circuit Description PD_A PD_B This is a two-state input controlling Power Down. PD = VA, Power Down is enabled and power dissipation is reduced. PD = AGND, Normal operation. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. Thus, Power Down is not available when the SPI Interface is enabled. TEST Test Mode. When this signal is asserted high, a fixed test pattern (10100110001110 msb->lsb) is sourced at the data outputs With this signal deasserted low, the device is in normal operation mode. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. WAM Word Alignment Mode. In single-lane mode this pin must be set to logic-0. In dual-lane mode only, when this signal is at logic-0 the serial data words are offset by half-word. With this signal at logic-1 the serial data words are aligned with each other. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. DLC Dual-Lane Configuration. The dual-lane mode is selected when this signal is at logic-0. With this signal at logic-1, all data is sourced on a single lane (SD1_x) for each channel. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. OUTCLK+ OUTCLK- Serial Clock. This pair of differential LVDS signals provides the serial clock that is synchronous with the Serial Data outputs. A bit of serial data is provided on each of the active serial data outputs with each falling and rising edge of this clock. This differential output is always enabled while the device is powered up. In powerdown mode this output is held in logic-low state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. FRAME+ FRAME- Serial Data Frame. This pair of differential LVDS signals transitions at the serial data word boundries. The SD1_A+/- and SD1_B+/output words always begin with the rising edge of the Frame signal. The falling edge of the Frame signal defines the start of the serial data word presented on the SD0_A+/- and SD0_B+/- signal pairs in the Dual-Lane mode. This differential output is always enabled while the device is powered up. In power-down mode this output is held in logic-low state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. 4 Symbol Equivalent Circuit Description SD1_A+ SD1_A- Serial Data Output 1 for Channel A. This is a differential LVDS pair of signals that carries channel A ADC's output in serialized form. The serial data is provided synchronous with the OUTCLK output. In Single-Lane mode each sample's output is provided in succession. In Dual-Lane mode every other sample output is provided on this output. This differential output is always enabled while the device is powered up. In power-down mode this output holds the last logic state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. SD1_B+ SD1_B- Serial Data Output 1 for Channel B. This is a differential LVDS pair of signals that carries channel B ADC's output in serialized form. The serial data is provided synchronous with the OUTCLK output. In Single-Lane mode each sample's output is provided in succession. In Dual-Lane mode every other sample output is provided on this output. This differential output is always enabled while the device is powered up. In power-down mode this output holds the last logic state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. SD0_A+ SD0_A- Serial Data Output 0 for Channel A. This is a differential LVDS pair of signals that carries channel A ADC's alternating samples' output in serialized form in Dual-Lane mode. The serial data is provided synchronous with the OUTCLK output. In Single-Lane mode this differential output is held in high impedance state. This differential output is always enabled while the device is powered up. In powerdown mode this output holds the last logic state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. SD0_B+ SD0_B- Serial Data Output 0 for Channel B. This is a differential LVDS pair of signals that carries channel B ADC's alternating samples' output in serialized form in Dual-Lane mode. The serial data is provided synchronous with the OUTCLK output. In Single-Lane mode this differential output is held in high impedance state. This differential output is always enabled while the device is powered up. In powerdown mode this output holds the last logic state. A 100-ohm termination resistor must always be used between this pair of signals at the far end of the transmission line. SPI_EN SPI Enable: The SPI interface is enabled when this signal is asserted high. In this case the direct control pins have no effect. When this signal is deasserted, the SPI interface is disabled and the direct control pins are enabled. 55 SCSb Serial Chip Select: While this signal is asserted SCLK is used to accept serial data present on the SDI input and to source serial data on the SDO output. When this signal is deasserted, the SDI input is ignored and the SDO output is in TRI-STATE mode. 52 SCLK Serial Clock: Serial data are shifted into and out of the device synchronous with this clock signal. 54 SDI 38 37 34 33 36 35 32 31 56 Serial Data-In: Serial data are shifted into the device on this pin while SCSb signal is asserted. 5 www.national.com ADC14DS105 Pin No. ADC14DS105 Pin No. Symbol 53 SDO Serial Data-Out: Serial data are shifted out of the device on this pin while SCSb signal is asserted. This output is in TRI-STATE mode when SCSb is deasserted. 46 30 ORA ORB Overrange. These CMOS outputs are asserted logic-high when their respective channel's data output is out-of-range in either high or low direction. DLL_Lock DLL_Lock Output. When the internal DLL is locked to the input CLK, this pin outputs a logic high. If the input CLK is changed abruptly, the internal DLL may become unlocked and this pin will output a logic low. Cycle Reset_DLL (pin 28) to re-lock the DLL to the input CLK. 8, 16, 17, 58, 60 VA Positive analog supply pins. These pins should be connected to a quiet source and be bypassed to AGND with 0.1 F capacitors located close to the power pins. 1, 4, 12, 15, Exposed Pad AGND 24 Equivalent Circuit Description ANALOG POWER The ground return for the analog supply. DIGITAL POWER 26, 40, 50 VDR 25, 39, 51 DRGND www.national.com Positive driver supply pin for the output drivers. This pin should be connected to a quiet voltage source and be bypassed to DRGND with a 0.1 F capacitor located close to the power pin. The ground return for the digital output driver supply. This pins should be connected to the system digital ground, but not be connected in close proximity to the ADC's AGND pins. 6 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VA, VDR) Voltage on Any Pin (Not to exceed 4.2V) Input Current at Any Pin other than Supply Pins (Note 4) Package Input Current (Note 4) Max Junction Temp (TJ) -40C TA +85C +2.7V to +3.6V Operating Temperature Supply Voltages Clock Duty Cycle (DCS Enabled) (DCS disabled) VCM |AGND-DRGND| -0.3V to 4.2V -0.3V to (VA +0.3V) 5 mA (Notes 1, 3) 30/70 % 45/55 % 1.4V to 1.6V 100mV 50 mA +150C 30C/W Thermal Resistance (JA) ESD Rating Human Body Model (Note 6) 2500V Machine Model (Note 6) 250V Storage Temperature -65C to +150C Soldering process must comply with National Semiconductor's Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 7) Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = 3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symbol Parameter Conditions Typical Limits (Note 10) Units (Limits) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes 14 Bits (min) INL Integral Non Linearity 1.5 4 -4 LSB (max) LSB (min) DNL Differential Non Linearity 0.5 1.5 -0.9 LSB (max) LSB (min) PGE Positive Gain Error -0.2 1 %FS (max) NGE Negative Gain Error 0.1 1 %FS (max) TC PGE Positive Gain Error -40C TA +85C TC NGE Negative Gain Error -40C TA +85C VOFF -8 -12 Offset Error TC VOFF Offset Error Tempco ppm/C 0.15 -40C TA +85C ppm/C 0.55 10 %FS (max) ppm/C Under Range Output Code 0 0 Over Range Output Code 16383 16383 REFERENCE AND ANALOG INPUT CHARACTERISTICS VCMO Common Mode Output Voltage 1.5 1.4 1.6 V (min) V (max) VCM Analog Input Common Mode Voltage 1.5 1.4 1.6 V (min) V (max) CIN VIN Input Capacitance (each pin to GND) VIN = 1.5 Vdc (Note 11) 0.5 V VREF Internal Reference Voltage TC VREF Internal Reference Voltage Tempco (CLK LOW) 8.5 pF (CLK HIGH) 3.5 pF 1.20 -40C TA +85C 18 VRP Internal Reference Top 2.0 VRN Internal Reference Bottom 1.0 7 1.176 1.224 V (min) V (max) ppm/C www.national.com ADC14DS105 Operating Ratings Absolute Maximum Ratings (Notes 1, 3) ADC14DS105 Symbol EXT VREF Parameter Conditions Typical Limits (Note 10) Units (Limits) Internal Reference Accuracy (VRP-VRN) 1.0 0.89 1.06 V (min) V (max) External Reference Voltage (Note 12) 1.20 1.176 1.224 V (min) V (max) Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = 3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symbol Parameter Conditions Typical Limits (Note 10) Units (Limits) (Note 2) DYNAMIC CONVERTER CHARACTERISTICS, AIN = -1dBFS FPBW Full Power Bandwidth SNR Signal-to-Noise Ratio SFDR SFDR ENOB THD THD H2 H2 H3 H3 SINAD Spurious Free Dynamic Range (ADC14DS105AISQ) Spurious Free Dynamic Range (ADC14DS105CISQ) Effective Number of Bits Total Harmonic Disortion (ADC14DS105AISQ) Total Harmonic Disortion (ADC14DS105CISQ) Second Harmonic Distortion (ADC14DS105AISQ) Second Harmonic Distortion (ADC14DS105CISQ) Third Harmonic Distortion (ADC14DS105AISQ) Third Harmonic Distortion (ADC14DS105CISQ) Signal-to-Noise and Distortion Ratio www.national.com -1 dBFS Input, -3 dB Corner 1.0 GHz fIN = 10 MHz 73 dBFS fIN = 70 MHz 72.5 dBFS fIN = 240 MHz 70.5 fIN = 10 MHz 90 69 dBFS dBFS fIN = 70 MHz 86 fIN = 240 MHz 83 fIN = 10 MHz 88 dBFS fIN = 70 MHz 85 dBFS fIN = 240 MHz 80 fIN = 10 MHz 11.8 dBFS 80 77.5 dBFS dBFS Bits fIN = 70 MHz 11.7 fIN = 240 MHz 11.3 fIN = 10 MHz -86 dBFS fIN = 70 MHz -85 dBFS fIN = 240 MHz -80 fIN = 10 MHz -86 Bits 11 -75 Bits dBFS dBFS fIN = 70 MHz -84 fIN = 240 MHz -78 fIN = 10 MHz -95 dBFS fIN = 70 MHz -90 dBFS fIN = 240 MHz -83 fIN = 10 MHz -90 dBFS -75 -80 dBFS dBFS dBFS fIN = 70 MHz -88 fIN = 240 MHz -80 fIN = 10 MHz -88 dBFS fIN = 70 MHz -85 dBFS fIN = 240 MHz -84 fIN = 10 MHz -87 dBFS -77.5 -80 dBFS dBFS dBFS fIN = 70 MHz -83 fIN = 240 MHz -80 fIN = 10 MHz 72.8 dBFS fIN = 70 MHz 72.3 dBFS fIN = 240 MHz 70 8 dBFS -77.5 68 dBFS dBFS Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) 2.0 V (min) 0.8 V (max) DIGITAL INPUT CHARACTERISTICS (CLK, PD_A,PD_B,SCSb,SPI_EN,SCLK,SDI,TEST,WAM,DLC) VIN(1) Logical "1" Input Voltage VA = 3.6V VIN(0) Logical "0" Input Voltage VA = 3.0V IIN(1) Logical "1" Input Current VIN = 3.3V 10 A IIN(0) Logical "0" Input Current VIN = 0V -10 A CIN Digital Input Capacitance 5 pF DIGITAL OUTPUT CHARACTERISTICS (ORA,ORB,SDO) VOUT(1) Logical "1" Output Voltage IOUT = -0.5 mA , VDR = 2.7V VOUT(0) Logical "0" Output Voltage IOUT = 1.6 mA, VDR = 2.7V +ISC Output Short Circuit Source Current VOUT = 0V -10 mA -ISC Output Short Circuit Sink Current VOUT = VDR 10 mA COUT Digital Output Capacitance 5 pF 2.0 V (min) 0.4 V (max) POWER SUPPLY CHARACTERISTICS IA IDR Analog Supply Current Full Operation 240 270 mA (max) Digital Output Supply Current Full Operation 70 80 mA 1000 1130 mW (max) Power Consumption Power Down Power Consumption Clock disabled 33 mW Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = 3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symb Parameter Conditions Typical (Note 10) Limits Units (Limits) Maximum Clock Frequency In Single-Lane Mode In Dual-Lane Mode 65 105 MHz (max) Minimum Clock Frequency In Single-Lane Mode In Dual-Lane Mode 25 52.5 MHz (min) tCONV Conversion Latency Single-Lane Mode Dual-Lane, Offset Mode Dual-Lane, Word Aligned Mode 7.5 8 9 Clock Cycles tAD Aperture Delay 0.6 ns tAJ Aperture Jitter 0.1 ps rms Serial Control Interface Timing and AC Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = 3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symb fSCLK Parameter Serial Clock Frequency Conditions fSCLK = fCLK/10 Typical (Note 10) Limits Units (Limits) 10.5 MHz (max) % (min) % (max) tPH SCLK Pulse Width - High % of SCLK Period 40 60 tPL SCLK Pulse Width - Low % of SCLK Period 40 60 % (min) % (max) tSU SDI Setup Time 5 ps (min) 9 www.national.com ADC14DS105 Logic and Power Supply Electrical Characteristics ADC14DS105 Symb Parameter Conditions Typical (Note 10) Limits Units (Limits) tH SDI Hold Time 5 ns (min) tODZ SDO Driven-to-Tri-State Time 40 50 ns (max) tOZD SDO Tri-State-to-Driven Time 15 20 ns (max) tOD SDO Output Delay Time 15 20 ns (max) tCSS SCSb Setup Time 5 10 ns (min) tCSH SCSb Hold Time 5 10 ns (min) tIAG Inter-Access Gap Minimum time SCSb must be deasserted between accesses Cycles of SCLK 3 LVDS Electrical Characteristics Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = 3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (Notes 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits Units (Limits) 350 250 450 mV (min) mV (max) 25 mV (max) 1.125 1.375 V (min) V (max) 25 mV (max) LVDS DC CHARACTERISTICS VOD Output Differential Voltage (SDO+) - (SDO-) RL = 100 delta VOD Output Differential Voltage Unbalance RL = 100 VOS Offset Voltage RL = 100 delta VOS Offset Voltage Unbalance RL = 100 IOS DO = 0V, VIN = 1.1V, Output Short Circuit Current 1.25 -10 mA (max) ns LVDS OUTPUT TIMING AND SWITCHING CHARACTERISTICS tDP Output Data Bit Period Dual-Lane Mode 1.36 tHO Output Data Edge to Output Clock Edge Dual-Lane Mode Hold Time (Note 12) 680 300 ps (min) tSUO Output Data Edge to Output Clock Edge Dual-Lane Mode Set-Up Time (Note 12) 640 300 ps (min) tFP Frame Period tFDC Frame Clock Duty Cycle (Note 12) tDFS Data Edge to Frame Edge Skew 50% to 50% 15 ps Output Delay of OR output From rising edge of CLKL to ORA/ORB valid 4 ns tODOR Dual-Lane Mode 19.05 50 ns 45 55 % (min) % (max) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is guaranteed to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. Note 2: This parameter is specified in units of dBFS - indicating the value that would be attained with a full-scale input signal. Note 3: All voltages are measured with respect to GND = AGND = DRGND = 0V, unless otherwise specified. Note 4: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be limited to 5 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to 10. Note 5: The maximum allowable power dissipation is dictated by TJ,max, the junction-to-ambient thermal resistance, (JA), and the ambient temperature, (TA), and can be calculated using the formula PD,max = (TJ,max - TA )/JA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Such conditions should always be avoided. Note 6: Human Body Model is 100 pF discharged through a 1.5 k resistor. Machine Model is 220 pF discharged through 0 Note 7: Reflow temperature profiles are different for lead-free and non-lead-free packages. Note 8: The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per (Note 4). However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. www.national.com 10 ADC14DS105 20211211 Note 9: With a full scale differential input of 2VP-P , the 14-bit LSB is 122.1 V. Note 10: Typical figures are at TA = 25C and represent most likely parametric norms at the time of product characterization. The typical specifications are not guaranteed. Note 11: The input capacitance is the sum of the package/pin capacitance and the sample and hold circuit capacitance. Note 12: This parameter is guaranteed by design and/or characterization and is not tested in production. 11 www.national.com ADC14DS105 LVDS Output Offset Voltage (VOS) is the midpoint between the differential output pair voltages. MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC is guaranteed not to have any missing codes. MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of 1/2 LSB above negative full scale. OFFSET ERROR is the difference between the two input voltages [(VIN+) - (VIN-)] required to cause a transition from code 8191 to 8192. OUTPUT DELAY is the time delay after the falling edge of the clock before the data update is presented at the output pins. PIPELINE DELAY (LATENCY) See CONVERSION LATENCY. POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of 11/2 LSB below positive full scale. POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. PSRR is the ratio of the Full-Scale output of the ADC with the supply at the minimum DC supply limit to the FullScale output of the ADC with the supply at the maximum DC supply limit, expressed in dB. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or DC. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first six harmonic levels at the output to the level of the fundamental at the output. THD is calculated as Specification Definitions APERTURE DELAY is the time after the rising edge of the clock to when the input signal is acquired or held for conversion. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the total time of one period. The specification here refers to the ADC clock input signal. COMMON MODE VOLTAGE (VCM) is the common DC voltage applied to both input terminals of the ADC. CONVERSION LATENCY is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. CROSSTALK is coupling of energy from one channel into the other channel. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio or SINAD. ENOB is defined as (SINAD 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as: Gain Error = Positive Full Scale Error - Negative Full Scale Error It can also be expressed as Positive Gain Error and Negative Gain Error, which are calculated as: PGE = Positive Full Scale Error - Offset Error NGE = Offset Error - Negative Full Scale Error INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a best fit straight line. The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS/2n, where "VFS" is the full scale input voltage and "n" is the ADC resolution in bits. LVDS Differential Output Voltage (VOD) is the absolute value of the difference between the differential output pair voltages (VD+ and VD-), each measured with respect to ground. www.national.com where f1 is the RMS power of the fundamental (output) frequency and f2 through f7 are the RMS power of the first six harmonic frequencies in the output spectrum. SECOND HARMONIC DISTORTION (2ND HARM) is the difference expressed in dB, between the RMS power in the input frequency at the output and the power in its 2nd harmonic level at the output. THIRD HARMONIC DISTORTION (3RD HARM) is the difference, expressed in dB, between the RMS power in the input frequency at the output and the power in its 3rd harmonic level at the output. 12 ADC14DS105 Timing Diagrams 20211214 FIGURE 1. Serial Output Data Timing 20211217 FIGURE 2. Serial Output Data Format in Single-Lane Mode 13 www.national.com ADC14DS105 20211218 FIGURE 3. Serial Output Data Format in Dual-Lane Mode www.national.com 14 ADC14DS105 Transfer Characteristic 20211210 FIGURE 4. Transfer Characteristic 15 www.national.com ADC14DS105 Typical Performance Characteristics DNL, INL Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, TA = 25C. DNL INL 20211241 www.national.com 20211242 16 Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +3.0V, Internal VREF = +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 40 MHz, TA = 25C. SNR, SINAD, SFDR vs. VA Distortion vs. VA 20211251 20211252 SNR, SINAD, SFDR vs. Clock Duty Cycle Distortion vs. Clock Duty Cycle 20211257 20211258 SNR, SINAD, SFDR vs. Clock Duty Cycle, DCS Enabled Distortion vs. Clock Duty Cycle, DCS Enabled 20211259 20211260 17 www.national.com ADC14DS105 Typical Performance Characteristics ADC14DS105 Spectral Response @ 10 MHz Input Spectral Response @ 70 MHz Input 20211268 20211269 Spectral Response @ 240 MHz Input IMD, fIN1 = 20 MHz, fIN2 = 21 MHz 20211270 www.national.com 20211271 18 Operating on a single +3.3V supply, the ADC14DS105 digitizes two differential analog input signals to 14 bits, using a differential pipelined architecture with error correction circuitry and an on-chip sample-and-hold circuit to ensure maximum performance. The user has the choice of using an internal 1.2V stable reference, or using an external 1.2V reference. Any external reference is buffered on-chip to ease the task of driving that pin. Duty cycle stabilization and output data format are selectable using the quad state function OF/DCS pin (pin 19). The output data can be set for offset binary or two's complement. EFS = 16384 ( 1 - sin (90 + dev)) Where dev is the angular difference in degrees between the two signals having a 180 relative phase relationship to each other (see Figure 6). For single frequency inputs, angular errors result in a reduction of the effective full scale input. For complex waveforms, however, angular errors will result in distortion. Applications Information 1.0 OPERATING CONDITIONS We recommend that the following conditions be observed for operation of the ADC14DS105: 2.7V VA 3.6V 2.7V VDR VA 25 MHz fCLK 105 MHz 1.2V internal reference VREF = 1.2V (for an external reference) VCM = 1.5V (from VCMO) 20211281 FIGURE 6. Angular Errors Between the Two Input Signals Will Reduce the Output Level or Cause Distortion It is recommended to drive the analog inputs with a source impedance less than 100. Matching the source impedance for the differential inputs will improve even ordered harmonic performance (particularly second harmonic). Table 1indicates the input to output relationship of the ADC14DS105. 2.0 ANALOG INPUTS 2.1 Signal Inputs 2.1.1 Differential Analog Input Pins The ADC14DS105 has a pair of analog signal input pins for each of two channels. V IN+ and VIN- form a differential input pair. The input signal, VIN, is defined as VIN = (VIN+) - (VIN-) Figure 5 shows the expected input signal range. Note that the common mode input voltage, VCM, should be 1.5V. Using VCMO (pins 7,9) for VCM will ensure the proper input common mode level for the analog input signal. The positive peaks of the individual input signals should each never exceed 2.6V. Each analog input pin of the differential pair should have a maximum peak-to-peak voltage of 1V, be 180 out of phase with each other and be centered around VCM.The peak-topeak voltage swing at each analog input pin should not exceed the 1V or the output data will be clipped. 20211280 FIGURE 5. Expected Input Signal Range 19 www.national.com ADC14DS105 For single frequency sine waves the full scale error in LSB can be described as approximately Functional Description ADC14DS105 TABLE 1. Input to Output Relationship VIN+ VIN- Binary Output 2's Complement Output VCM - VREF/2 VCM + VREF/2 00 0000 0000 0000 10 0000 0000 0000 VCM - VREF/4 VCM + VREF/4 01 0000 0000 0000 11 0000 0000 0000 VCM VCM 10 0000 0000 0000 00 0000 0000 0000 VCM + VREF/4 VCM - VREF/4 11 0000 0000 0000 01 0000 0000 0000 VCM + VREF/2 VCM - VREF/2 11 1111 1111 1111 01 1111 1111 1111 Negative Full-Scale Mid-Scale Positive Full-Scale Figure 7 and Figure 8 show examples of single-ended to differential conversion circuits. The circuit in Figure 7 works well for input frequencies up to approximately 70MHz, while the circuit in Figure 8 works well above 70MHz. 2.1.2 Driving the Analog Inputs The VIN+ and the VIN- inputs of the ADC14DS105 have an internal sample-and-hold circuit which consists of an analog switch followed by a switched-capacitor amplifier. 20211282 FIGURE 7. Low Input Frequency Transformer Drive Circuit 20211283 FIGURE 8. High Input Frequency Transformer Drive Circuit One short-coming of using a transformer to achieve the single-ended to differential conversion is that most RF transformers have poor low frequency performance. A differential amplifier can be used to drive the analog inputs for low frequency applications. The amplifier must be fast enough to settle from the charging glitches on the analog input resulting from the sample-and-hold operation before the clock goes high and the sample is passed to the ADC core. that voltage is used for the reference. The VREF pin should always be bypassed to ground with a 0.1 F capacitor close to the reference input pin. It is important that all grounds associated with the reference voltage and the analog input signal make connection to the ground plane at a single, quiet point to minimize the effects of noise currents in the ground path. The Reference Bypass Pins (VRP, VCMO, and VRN) for channels A and B are made available for bypass purposes. These pins should each be bypassed to AGND with a low ESL (equivalent series inductance) 1 F capacitor placed very close to the pin to minimize stray inductance. A 0.1 F capacitor should be placed between VRP and VRN as close to the pins as possible, and a 1 F capacitor should be placed in parallel. This configuration is shown in Figure 9. It is necessary to avoid reference oscillation, which could result in reduced SFDR and/or SNR. VCMO may be loaded to 1mA for use as a temperature stable 1.5V reference. The remaining pins should not be loaded. Smaller capacitor values than those specified will allow faster recovery from the power down mode, but may result in de- 2.1.3 Input Common Mode Voltage The input common mode voltage, VCM, should be in the range of 1.4V to 1.6V and be a value such that the peak excursions of the analog signal do not go more negative than ground or more positive than 2.6V. It is recommended to use VCMO (pins 7,9) as the input common mode voltage. 2.2 Reference Pins The ADC14DS1050 is designed to operate with an internal or external 1.2V reference. The internal 1.2 Volt reference is the default condition when no external reference input is applied to the VREF pin. If a voltage is applied to the VREF pin, then www.national.com 20 sible to the ADC clock pin but beyond it as seen from the clock source. Typical tPD is about 150 ps/inch (60 ps/cm) on FR-4 board material. The units of "L" and tPD should be the same (inches or centimeters). The duty cycle of the clock signal can affect the performance of the A/D Converter. Because achieving a precise duty cycle is difficult, the ADC14DS105 has a Duty Cycle Stabilizer. 3.2 Power-Down (PD_A and PD_B) The PD_A and PD_B pins, when high, hold the respective channel of the ADC14DS105 in a power-down mode to conserve power when that channel is not being used. The channels may be powereed down individually or together. The data in the pipeline is corrupted while in the power down mode. The Power Down Mode Exit Cycle time is determined by the value of the components on the reference bypass pins ( VRP, VCMO and VRN ). These capacitors loose their charge in the Power Down mode and must be recharged by on-chip circuitry before conversions can be accurate. Smaller capacitor values allow slightly faster recovery from the power down mode, but can result in a reduction in SNR, SINAD and ENOB performance. Note: This signal has no effect when SPI_EN is high and the serial control interface is enabled. 2.3 OF/DCS Pin Duty cycle stabilization and output data format are selectable using this quad state function pin. When enabled, duty cycle stabilization can compensate for clock inputs with duty cycles ranging from 30% to 70% and generate a stable internal clock, improving the performance of the part. With OF/DCS = VA the output data format is 2's complement and duty cycle stabilization is not used. With OF/DCS = AGND the output data format is offset binary and duty cycle stabilization is not used. With OF/DCS = (2/3)*VA the output data format is 2's complement and duty cycle stabilization is applied to the clock. If OF/DCS is (1/3)*VA the output data format is offset binary and duty cycle stabilization is applied to the clock. While the sense of this pin may be changed "on the fly," doing this is not recommended as the output data could be erroneous for a few clock cycles after this change is made. Note: This signal has no effect when SPI_EN is high and the serial control interface is enabled. 3.3 Reset_DLL This pin is normally low. If the input clock frequency is changed abruptly, the internal timing circuits may become unlocked. Cycle this pin high for 1 microsecond to re-lock the DLL. The DLL will lock in several microseconds after Reset_DLL is asserted. 3.0 DIGITAL INPUTS Digital CMOS compatible inputs consist of CLK, and PD_A, PD_B, Reset_DLL, DLC, TEST, WAM, SPI_EN, SCSb, SCLK, and SDI. 3.4 DLC This pin sets the output data configuration. With this signal at logic-1, all data is sourced on a single lane (SD1_x) for each channel. When this signal is at logic-0, the data is sourced on dual lanes (SD0_x and SD1_x) for each channel. This simplifies data capture at higher data rates. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. 3.1 Clock Input The CLK controls the timing of the sampling process. To achieve the optimum noise performance, the clock input should be driven with a stable, low jitter clock signal in the range indicated in the Electrical Table. The clock input signal should also have a short transition region. This can be achieved by passing a low-jitter sinusoidal clock source through a high speed buffer gate. The trace carrying the clock signal should be as short as possible and should not cross any other signal line, analog or digital, not even at 90. The clock signal also drives an internal state machine. If the clock is interrupted, or its frequency is too low, the charge on the internal capacitors can dissipate to the point where the accuracy of the output data will degrade. This is what limits the minimum sample rate. The clock line should be terminated at its source in the characteristic impedance of that line. Take care to maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905 for information on setting characteristic impedance. It is highly desirable that the the source driving the ADC clock pins only drive that pin. However, if that source is used to drive other devices, then each driven pin should be AC terminated with a series RC to ground, such that the resistor value is equal to the characteristic impedance of the clock line and the capacitor value is 3.5 TEST When this signal is asserted high, a fixed test pattern (10100110001110 msb->lsb) is sourced at the data outputs. When low, the ADC is in normal operation. The user may specify a custom test pattern via the serial control interface. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. 3.6 WAM In dual-lane mode only, when this signal is at logic-0 the serial data words are offset by half-word. With this signal at logic-1 the serial data words are aligned with each other. In single lane mode this pin must be set to logic-0. Note: This signal has no effect when SPI_EN is high and the SPI interface is enabled. 3.7 SPI_EN The SPI interface is enabled when this signal is asserted high. In this case the direct control pins (OF/DCS, PD_A, PD_B, DLC, WAM, TEST) have no effect. When this signal is deasserted, the SPI interface is disabled and the direct control pins are enabled. where tPD is the signal propagation rate down the clock line, "L" is the line length and ZO is the characteristic impedance of the clock line. This termination should be as close as pos21 www.national.com ADC14DS105 graded noise performance. Loading any of these pins, other than VCMO may result in performance degradation. The nominal voltages for the reference bypass pins are as follows: VCMO = 1.5 V VRP = 2.0 V VRN = 1.0 V ADC14DS105 3.8 SCSb, SDI, SCLK These pins are part of the SPI interface. See Section 5.0 for more information. the dual-lane scheme. In either case DDR-type clocking is used. For each data channel, an overrange indication is also provided. The OR signal is updated with each frame of data. 4.0 DIGITAL OUTPUTS Digital outputs consist of six LVDS signal pairs (SD0_A, SD1_A, SD0_B, SD1_B, OUTCLK, FRAME) and CMOS logic outputs ORA, ORB, DLL_Lock, and SDO. 4.2 ORA, ORB These CMOS outputs are asserted logic-high when their respective channel's data output is out-of-range in either high or low direction. 4.1 LVDS Outputs The digital data for each channel is provided in a serial format. Two modes of operation are available for the serial data format. Single-lane serial format (shown in Figure 2) uses one set of differential data signals per channel. Dual-lane serial format (shown in Figure 3) uses two sets of differential data signals per channel in order to slow down the data and clock frequency by a factor of 2. At slower rates of operation (typically below 65 MSPS) the single-lane mode may the most efficient to use. At higher rates the user may want to employ 4.3 DLL_Lock When the internal DLL is locked to the input CLK, this pin outputs a logic high. If the input CLK is changed abruptly, the internal DLL may become unlocked and this pin will output a logic low. Cycle Reset_DLL to re-lock the DLL to the input CLK. 4.4 SDO This pin is part of the SPI interface. See Section 5.0 for more information. 20211285 FIGURE 9. Application Circuit DCS, PD_A, PD_B, DLC, WAM, TEST) have no effect. When this signal is deasserted, the SPI interface is disabled and the direct control pins are enabled. Each serial interface access cycle is exactly 16 bits long. Figure 10 shows the access protocol used by this interface. Each signal's function is described below. The Read Timing is shown in Figure 11, while the Write Timing is shown in Figure 12 5.0 Serial Control Interface The ADC14DS105 has a serial interface that allows access to the control registers. The serial interface is a generic 4-wire synchronous interface that is compatible with SPI type interfaces that are used on many microcontrollers and DSP controllers. The ADC's input clock must be running for the Serial Control Interface to operate. It is enabled when the SPI_EN (pin 56) signal is asserted high. In this case the direct control pins (OF/ www.national.com 22 ADC14DS105 20211219 FIGURE 10. Serial Interface Protocol SCLK: Used to register the input data (SDI) on the rising edge; and to source the output data (SDO) on the falling edge. User may disable clock and hold it in the low-state, as long as clock pulse-width min spec is not violated when clock is enabled or disabled. SCSb: Serial Interface Chip Select. Each assertion starts a new register access - i.e., the SDATA field protocol is required. The user is required to deassert this signal after the 16th clock. If the SCSb is deasserted before the 16th clock, no address or data write will occur. The rising edge captures the address just shifted-in and, in the case of a write operation, writes the addressed register. There is a minimum pulsewidth requirement for the deasserted pulse - which is specified in the Electrical Specifications section. SDI: Serial Data. Must observe setup/hold requirements with respect to the SCLK. Each cycle is 16-bits long. R/Wb: A value of '1' indicates a read operation, while a value of '0' indicates a write operation. Reserved: Reserved for future use. Must be set to 0. ADDR: Up to 3 registers can be addressed. DATA: In a write operation the value in this field will be written to the register addressed in this cycle when SCSb is deasserted. In a read operation this field is ignored. SDO: This output is normally at TRI-STATE and is driven only when SCSb is asserted. Upon SCSb assertion, contents of the register addressed during the first byte are shifted out with the second 8 SCLK falling edges. Upon power-up, the default register address is 00h. 23 www.national.com ADC14DS105 20211216 FIGURE 11. Read Timing 20211215 FIGURE 12. Write Timing Device Control Register, Address 0h 7 6 5 4 3 2 1 Bit 3 Output Data Format. When this bit is set to `1' the data output is in the "twos complement" form. When this bit is set to `0' the data output is in the "offset binary" form. Bit 2 Word Alignment Mode. This bit must be set to '0' in the single-lane mode of operation. In dual-lane mode, when this bit is set to '0' the serial data words are offset by half-word. This gives the least latency through the device. When this bit is set to '1' the serial data words are in word-aligned mode. In this mode the serial data on the SD1 lane is additionally delayed by one CLK cycle. (Refer to Figure 3). Bit 1 Power-Down Channel A. When this bit is set to '1', Channel A is in power-down state and Normal operation is suspended. Bit 0 Power-Down Channel B. When this bit is set to '1', Channel B is in power-down state and Normal operation is suspended. 0 OM DLC DCS OF WAM PD_A PD_B Reset State : 08h Bits (7:6) Operational Mode 0 0 Normal Operation. 0 1 Test Output mode. A fixed test pattern (10100110001110 msb->lsb) is sourced at the data outputs. 1 0 Test Output mode. Data pattern defined by user in registers 01h and 02h is sourced at data outputs. 1 1 Reserved. Bit 5 Bit 4 Data Lane Configuration. When this bit is set to '0', the serial data interface is configured for dual-lane mode where the data words are output on two data outputs (SD1 and SD0) at half the rate of the single-lane interface. When this bit is set to `1', serial data is output on the SD1 output only and the SD0 outputs are held in a high-impedance state User Test Pattern Register 0, Address 1h 7 Duty Cycle Stabilizer. When this bit is set to '0' the DCS is off. When this bit is set to `1', the DCS is on. www.national.com 6 5 4 3 2 1 0 Reserved User Test Pattern (13:8) 24 User Test Pattern Register 1, Address 2h 7 6 5 4 3 2 1 0 User Test Pattern (7:0) Reset State : 00h Bits (7:0) User Test Pattern. Least-significant 8 bits of the 14-bit pattern that will be sourced out of the data outputs in Test Output Mode. 6.0 POWER SUPPLY CONSIDERATIONS The power supply pins should be bypassed with a 0.1 F capacitor and with a 100 pF ceramic chip capacitor close to each power pin. Leadless chip capacitors are preferred because they have low series inductance. As is the case with all high-speed converters, the ADC14DS105 is sensitive to power supply noise. Accordingly, the noise on the analog supply pin should be kept below 100 mVP-P. No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be especially careful of this during power turn on and turn off. 8.0 DYNAMIC PERFORMANCE To achieve the best dynamic performance, the clock source driving the CLK input must have a sharp transition region and be free of jitter. Isolate the ADC clock from any digital circuitry with buffers, as with the clock tree shown in Figure 13. The gates used in the clock tree must be capable of operating at frequencies much higher than those used if added jitter is to be prevented. As mentioned in Section 6.0, it is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can lead to reduced SNR performance, and the clock can introduce noise into other lines. Even lines with 90 crossings have capacitive coupling, so try to avoid even these 90 crossings of the clock line. 7.0 LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining separate analog and digital areas of the board, with the ADC14DS105 between these areas, is required to achieve specified performance. Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the clock line as short as possible. Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane area. Generally, analog and digital lines should cross each other at 90 to avoid crosstalk. To maximize accuracy in high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the generally accepted 90 crossing should be avoided with the clock line as even a little coupling can cause problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to degradation of SNR. Also, the high speed clock can introduce noise into the analog chain. Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the signal path 20211286 FIGURE 13. Isolating the ADC Clock from other Circuitry with a Clock Tree 25 www.national.com ADC14DS105 through all components should form a straight line wherever possible. Be especially careful with the layout of inductors and transformers. Mutual inductance can change the characteristics of the circuit in which they are used. Inductors and transformers should not be placed side by side, even with just a small part of their bodies beside each other. For instance, place transformers for the analog input and the clock input at 90 to one another to avoid magnetic coupling. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter's input pins and ground or to the reference input pin and ground should be connected to a very clean point in the ground plane. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed in the analog area of the board. All digital circuitry and dynamic I/O lines should be placed in the digital area of the board. The ADC14DS105 should be between these two areas. Furthermore, all components in the reference circuitry and the input signal chain that are connected to ground should be connected together with short traces and enter the ground plane at a single, quiet point. All ground connections should have a low inductance path to ground. Reset State : 00h Bits (7:6) Reserved. Must be set to '0'. Bits (5:0) User Test Pattern. Most-significant 6 bits of the 14-bit pattern that will be sourced out of the data outputs in Test Output Mode. ADC14DS105 Physical Dimensions inches (millimeters) unless otherwise noted TOP View...............................SIDE View...............................BOTTOM View 60-Lead LLP Package Ordering Numbers: ADC14DS105AISQ / ADC14DS105CISQ NS Package Number SQA60A www.national.com 26 ADC14DS105 Notes 27 www.national.com ADC14DS105 Dual 14-Bit, 105 MSPS A/D Converter with Serial LVDS Outputs Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated