Preliminary Specification Number : SP-9B1LV-M
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
W-LAN+Bluetooth Combo Module Data Sheet
Cypress Chipset CYW43012
for 802.11a/b/g/n,11ac-friendly + Bluetooth 5.0
Tentative P/N :LBEE59B1LV-TEMP
Preliminary Specification Number : SP-9B1LV-M
1 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
The revision history of the product specification
Revised No.
Revised Date
Note
-
2017.07.07
First Issue
A
2017.10.02
P4. Updated Block Diagram
P6,8. Updated Pin Layout
B
2017.10.10
Cover. Added 11ac-friendly
P4. Added 11ac-friendly on Scope
C
2018.04.04
P35. Added Reference circuit
D
2018.06.01
P10. Updated Supply voltage condition
P25-31. Updated DC/RF characteristics
E
2018.08.02
P4. Updated Wright/MSL information
P31-32. Updated BT output power spec
P34 Updated Reference schematic(Added (*5))
P35 Added Tape and Reel packing information
F
2018.10.25
P4. Added “MAC/BD address are embedded
P5. Updated Marking information
P10. Updated VDDIO_SFL spec(8.OPERATING CONDITION)
P13. Added digital I/O requirements BT/WL_REG_ON
G
2018.12.28
P33. Revised Reference circuit
H
2019.03.26
P5. Corrected Demotions(Added a5,c5)
I
2019.04.24
P40. Updated 18.PRECONDITION TO USE OUR PRODUCTS
J
2019.07.05
P5. Added Certification information
Appendix : Added User manual for Japan certification
K
2019.09.26
P5. Certification information: Added
P6. Dimensions: added e12 number
L
2019.10.17
P10. Dimensions : added pin 80(corrected)
P34. Reference circuit : added pin64(corrected)
M
2019.11.21
Updated based on the latest Cypress IC datasheet (Rev.L).
P7. Pin Layout : Updated
P8. Pin Description: Updated
Removed PCM/I2S interface timing
Preliminary Specification Number : SP-9B1LV-M
2 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
TABLE OF CONTENTS
1. SCOPE ..................................................................................................................................................... 4
2. KEY FEATURE ...................................................................................................................................... 4
3. Part Number ........................................................................................................................................... 4
4. RoHS Compliance ................................................................................................................................... 4
5. Block Diagram ........................................................................................................................................ 4
6. Certification Information ....................................................................................................................... 5
6.1. Radio Certification ................................................................................................................... 5
USA ...................................................................................................................................................... 5
Canada ................................................................................................................................................. 5
Europe .................................................................................................................................................. 5
Japan .................................................................................................................................................... 5
6.2. Bluetooth® Qualification .......................................................................................................... 5
7. DIMENSIONS, MARKING AND TERMINAL CONFIGURATIONS ................................................. 6
7.1. Dimensions ............................................................................................................................... 6
7.2. Pin Layout ................................................................................................................................. 7
7.3. Module PIN Descriptions ......................................................................................................... 8
8. ABSOLUTE MAXIMUM RATINGS*2).................................................................................................. 11
9. OPERATING CONDITION*3) ............................................................................................................... 11
10. External LPO Signal Requirement................................................................................................... 11
11. POWER ON SEQUENCE ................................................................................................................ 12
11.1. Power On Sequence for WLAN ON and BT ON ............................................................... 12
11.2. Power On Sequence for WLAN ON and BT Off ............................................................... 12
11.3. Power On Sequence for WLAN OFF and BT ON ............................................................. 13
11.4. Power On Sequence for WLAN OFF and BT OFF ........................................................... 13
12. Digital I/O Requirements ................................................................................................................. 14
13. INTERFACE TIMING AND AC CHARACTERISTICS ................................................................. 15
13.1. Bluetooth UART Timing .................................................................................................... 15
13.2. Bluetooth PCM Interface Timing ...................................................................................... 15
13.2.1. Short Frame Sync, Master Mode ............................................................................... 15
13.2.2. Short Frame Sync, Slave Mode .................................................................................. 15
13.2.3. Long Frame Sync, Master Mode ................................................................................ 15
13.2.4. Long Frame Sync, Slave Mode ................................................................................... 15
13.2.5. Short Frame Sync, Burst Mode .................................................................................. 15
13.2.6. Long Frame Sync, Burst Mode ................................................................................... 15
13.3. I2S Timing ........................................................................................................................... 15
13.3.1. I2S Transmitter Timing ............................................................................................... 15
13.3.2. I2S Receiver Timing ..................................................................................................... 15
13.4. SDIO Timing ....................................................................................................................... 16
13.4.1. SDIO Default Mode Timing ........................................................................................ 16
13.4.2. SDIO High-Speed Mode Timing ................................................................................. 17
13.4.3. SDIO BUS Timing Specifications in SDR Modes ..................................................... 18
14. DC / RF Characteristics.................................................................................................................... 20
14.1. DC/RF Characteristics for IEEE802.11b - 2.4GHz .......................................................... 20
14.2. DC/RF Characteristics for IEEE802.11g - 2.4GHz .......................................................... 21
14.3. DC/RF Characteristics for IEEE802.11n – 2.4GHz ......................................................... 22
14.4. DC/RF Characteristics for IEEE802.11a - 5GHz ............................................................. 23
14.5. DC/RF Characteristics for IEEE802.11n(HT20) - 5GHz ................................................. 24
14.6. DC/RF Characteristics for IEEE802.11ac(VHT20) - 5GHz ............................................. 25
14.7. DC/RF Characteristics for Bluetooth ................................................................................ 26
14.8. DC/RF Characteristics for Bluetooth (LE) ........................................................................ 27
15. LAND PATTERN (TOP VIEW) ........................................................................................................ 28
16. REFERENCE CIRCUIT ................................................................................................................... 29
17. TAPE AND REEL PACKING ........................................................................................................... 30
18. NOTICE ............................................................................................................................................. 33
18.1. Storage Conditions: ............................................................................................................ 33
Preliminary Specification Number : SP-9B1LV-M
3 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
18.2. Handling Conditions: ......................................................................................................... 33
18.3. Standard PCB Design (Land Pattern and Dimensions): ................................................. 33
18.4. Notice for Chip Placer: ....................................................................................................... 33
18.5. Soldering Conditions: ......................................................................................................... 34
18.6. Cleaning: ............................................................................................................................. 34
18.7. Operational Environment Conditions: .............................................................................. 34
18.8. Input Power Capacity: ........................................................................................................ 35
19. PRECONDITION TO USE OUR PRODUCTS ............................................................................... 36
Please be aware that an important notice concerning availability, standard warranty and use in critical applications of
Murata products and disclaimers thereto appears at the end of this specification sheet.
Preliminary Specification Number : SP-9B1LV-M
4 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
1. SCOPE
This specification is applied to the IEEE802.11a/b/g/n,IEEE802.11ac-friendly W-LAN + Bluetooth
5.0 combo module.
*1)IEEE 802.11ac full-compliance requires support for 40 MHz and 80 MHz channel bandwidths. CYW43012 only
supports 20 MHz channel bandwidth however it supports 802.11ac’s 256-QAM for the 20 MHz channels in the 5GHz
band enabling it to offer higher throughput and lower energy per bit than 802.11n only products.
2. KEY FEATURE
- Cypress CYW43012 inside
- Compliant with IEEE802.11a/b/g/n, 11ac-friendly
- Compliant with Bluetooth specification v5.0
- SDIO interface for W-LAN
- Interface support for Bluetooth is Host Controller Interface (HCI)
- Surface mount type 10.0 x 7.2 mm (Typical), H = 1.4 mm (Max)
- MAC/BD address are embedded
- Weight : 0.23g
- MSL : 3
3. Part Number
Ordering Part Number
Description
LBEE59B1LV-TEMP
In case of sample order
LBEE59B1LV-TEMP-D
EVK
4. RoHS Compliance
This module is compliant with the RoHS directive.
5. Block Diagram
Sleep Clock
BPF
VBAT
VDDIO
SDIO
UART
Ref Clock
37.4MHz
CYW43012
5G Tx
5G Rx
2.4G Tx(WLAN)
2.4G Rx(WLAN)
BT: Tx
BT: Rx
LC network
For DCDC
DIPLEX
*1)
*1)
Preliminary Specification Number : SP-9B1LV-M
5 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
6. Certification Information
6.1. Radio Certification
USA
FCC ID : VPYLBEE59B1LV
Country Code: US/0
*Please follow user/installation manual of Appendix
Canada
IC : 772C-LBEE59B1LV
Country Code: CA/0
*Please follow user/installation manual of Appendix
Europe
EN300328/301893 v2.1.1, EN300440 v2.2.1 conducted test report is prepared.
Country Code: DE/0
Japan
Japanese type certification is prepared.
001-P01338
Country Code: JP/0
*Please follow manual of Appendix
The each country code are defined by Murata Blob/Nvram file.
Murata prepared 4 kinds of Blob files.
• STA/Indoor: US/CA/DE/JP
• STA/Outdoor: US/CA/DE/JP
• AP/Indoor: US/CA/DE/JP
• AP/Outdoor :US/CA/DE
Please ask your contact person from Murata.
6.2. Bluetooth® Qualification
QDID: 125836
Preliminary Specification Number : SP-9B1LV-M
6 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
7. DIMENSIONS, MARKING AND TERMINAL CONFIGURATIONS
7.1. Dimensions
<TOP VIEW> <BOTTOM VIEW>
(1)
(19)
(20)
(29)
(30) (48)
(49)
(58)
(59)
(71)
(72)
(76)
(77) (89)
(90)
(94)
(95)
(96)(97)
(98)
(99)
(100) (101) (102) (103)
(104)
(105)
(106)
a1 b1
e1
b2
c1
e2
a2
e3
b3 e4 a3 e5 e6 e7 c3
c5
e8
c4
e9
e10
a4
e11
a5
e12
c2
L
W
conformal shield
(1)
(19)
(20)
(29)
(30) (48)
(49)
(58)
(59)
(71)
(72)
(76)
(77) (89)
(90)
(94)
(95)
(96)(97)
(98)
(99)
(100) (101) (102) (103)
(104)
(105)
(106)
a1 b1
e1
b2
c1
e2
a2
e3
b3 e4 a3 e5 e6 e7 c3
c5
e8
c4
e9
e10
a4
e11
a5
e12
c2
L
W
conformal shield
<SIDE VIEW>
T
(unit : mm)
Mark
Dimensions
Mark
Dimensions
Mark
Dimensions
L
10.0 +/- 0.2
W
7.2 +/- 0.2
T
1.4max
a1
0.25+/- 0.1
a2
0.25 +/- 0.1
a3
0.25 +/- 0.1
a4
0.25 +/- 0.1
a5
0.25 +/- 0.1
b1
0.375 +/- 0.2
b2
0.30 +/- 0.2
b3
0.30 +/- 0.2
c1
0.55 +/- 0.1
c2
0.55 +/- 0.1
c3
0.55 +/- 0.1
c4
0.55 +/- 0.1
c5
0.55 +/- 0.1
e1
0.25 +/- 0.1
e2
0.375 +/- 0.1
e3
0.25 +/- 0.1
e4
1.025 +/- 0.1
e5
0.25 +/- 0.1
e6
0.25 +/- 0.1
e7
1.100 +/- 0.1
e8
0.825 +/- 0.1
e9
0.25 +/- 0.1
e10
0.25 +/- 0.1
e11
0.25 +/- 0.1
e12
0.75 +/- 0.1
Marking
Meaning
A
Murata Logo
B
Inspection Number
C
Module Type
D
Pin 1 Marking
Structure
PWB
Substrate
SMD Dip SPDT
SP3T CYW43012 Resin
Mold
Shield
012345678
Type1LV
A
B
D
C
Conformal shield
Conformal shield
Preliminary Specification Number : SP-9B1LV-M
7 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
7.2. Pin Layout
(1) (19)
(30)
(48)
(49)
(58) (59) (71)
(72)
(76)
(77)
(89)
(90)
(94) (95) (96) (97) (98)
(99)
(100)
(101)(102)
(103)
(104) (105) (106)
No.
Pin name
No.
Pin name
No.
Pin name
No.
Pin name
1
GND
25
SDIO_DATA_3
49
BT_RF_OUT
73
GND
2
GND
26
SDIO_CMD
50
GND
74
SFL_IO0
3
GND
27
GND
51
BT_RF_IN
75
SFL_IO3
4
VDDIO_SFL
28
VDDOUT_VDDIO
52
GND
76
SFL_IO2
5
BT_HOST_WAKE
29
BT_GPIO_0
53
GND
77
SFL_CLK
6
GND
30
GND
54
RF_SW_CTRL_6
78
SFL_IO1
7
WL_HOST_WAKE
31
BT_UART_TXD
55
RF_SW_CTRL_10
79
SFL_CS
8
WL_GPIO_1
32
BT_UART_RXD
56
RF_SW_CTRL_5
80
EXT_LPO
9
BT_REG_ON
33
BT_UART_RTS
57
GND
81
CLK_REQ
10
WL_REG_ON
34
BT_UART_CTS
58
ANT0
82
BT_PCM_OUT
11
GND
35
VDDIO
59
GND
83
BT_PCM_SYNC
12
VOUT_3P3
36
GND
60
GND
84
BT_PCM_IN
13
VBAT
37
P9
61
WL_GPIO_15
85
BT_PCM_CLK
14
VBAT
38
P11
62
WL_GPIO_13
86
BT_I2S_WS
15
GND
39
P13
63
WL_ GPIO_12
87
BT_I2S_CLK
16
RF_SW_CTRL_8
40
P5
64
WL_GPIO_14
88
BT_I2S_DI
17
RF_SW_CTRL_12
41
P6
65
GND
89
BT_I2S_DO
18
RF_SW_CTRL_11
42
P8
66
WL_GPIO_5
90
BT_GPIO_2
19
GND
43
P7
67
WL_GPIO_4
91
BT_GPIO_5
20
GND
44
P12
68
WL_GPIO_3
92
BT_GPIO_4
21
SDIO_DATA_2
45
P0
69
WL_GPIO_2
93
BT_GPIO_3
22
SDIO_DATA_1
46
P1
70
NC
94-106
GND
23
SDIO_DATA_0
47
GND
71
WL_GPIO_6
-
-
24
SDIO_CLK
48
GND
72
GND
-
-
Top View
Preliminary Specification Number : SP-9B1LV-M
8 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
7.3. Module PIN Descriptions
No.
Pin name
Type
Connection to
IC pin name
Description
1
GND
-
GND
Ground
2
GND
-
GND
Ground
3
GND
-
GND
Ground
4
VDDIO_SFL
I
VDDIO_SFL
DC supply voltage for SFLASH I/O
5
BT_HOST_WAKE
O
BT_HOST_WAKE
Bluetooth host wake
6
GND
-
GND
Ground
7
WL_HOST_WAKE
I/O
GPIO_0
WL_HOST_WAKE
8
WL_GPIO_1
I/O
GPIO_1
WLAN general-purpose I/Os
9
BT_REG_ON
I
BT_REG_ON
Used by the PMU to power-up or
power-down the internal regulators
used by the Bluetooth section
10
WL_REG_ON
I
WL_REG_ON
Used by the PMU to power up or
power down the internal regulators
used by the WLAN section
11
GND
-
GND
Ground
12
VOUT_3P3
O
VDDOUT_RF3P3
VDDIO_RF1
Output of 3.3V RF LDO
13
VBAT
I
SR_VDDBAT5
LDO_VDDBAT5
WRF_GENTRAL_VDD_V5P0
Power supply
14
VBAT
WRF_TX_VDD_V5P0
ET_LINREG_VDD_V5P0
ET_SWREG_VDD_V5P0
15
GND
-
GND
Ground
16
RF_SW_CTRL_8
O
RF_SW_CTRL_8
Programmable RF switch-control
lines
17
RF_SW_CTRL_12
O
RF_SW_CTRL_12
Programmable RF switch-control
lines
18
RF_SW_CTRL_11
O
RF_SW_CTRL_11
Programmable RF switch-control
lines
19
GND
-
GND
Ground
20
GND
-
GND
Ground
21
SDIO_DATA_2
I/O
SDIO_DATA_2
SDIO data line 2
22
SDIO_DATA_1
I/O
SDIO_DATA_1
SDIO data line 1
23
SDIO_DATA_0
I/O
SDIO_DATA_0
SDIO data line 0
24
SDIO_CLK
I
SDIO_CLK
SDIO clock
25
SDIO_DATA_3
I/O
SDIO_DATA_3
SDIO data line 3
26
SDIO_CMD
I/O
SDIO_CMD
SDIO command line
27
GND
-
GND
Ground
28
VDDOUT_VDDIO
O
VDDOUT_VDDIO
OTP_VDD1P8
VDDP_RF1
VDDP_SFL
output for 1.8V power switch
29
BT_GPIO_0
I/O
BT_GPIO_0
Bluetooth general-purpose I/Os
30
GND
-
GND
Ground
31
BT_UART_TXD
O
BT_UART_TXD
UART serial output
32
BT_UART_RXD
I
BT_UART_RXD
UART serial input
33
BT_UART_RTS
O
BT_UART_RTS_N
UART request-to-send
34
BT_UART_CTS
I
BT_UART_CTS_N
UART clear-to-send
Preliminary Specification Number : SP-9B1LV-M
9 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
No.
Pin name
Type
Connection to
IC pin name
Description
35
VDDIO
I
VDDIO
PMU_VDDIOA
PMU_VDDIOP
STRAP_OFF_1P8
VDD18_FLL,BT_VD
DO
BT_VDDO_HIB
PAD_ADC_AVDDC
Power supply
36
GND
-
GND
Ground
37
P9
I/O
P9
Programmable LHL/HIB pads
38
P11
I/O
P11
Programmable LHL/HIB pads
39
P13
I/O
P13
Programmable LHL/HIB pads
40
P5
I/O
P5
Programmable LHL/HIB pads
P5 is used as BT_DEV_WAKE
41
P6
I/O
P6
Programmable LHL/HIB pads
42
P8
O
P8
Programmable LHL/HIB pads
*Output Only
43
P7
I/O
P7
Programmable LHL/HIB pads
P7 is used as WL_DEV_WAKE
44
P12
I/O
P12
Programmable LHL/HIB pads
45
P0
I/O
P0
Programmable LHL/HIB pads
46
P1
I/O
P1
Programmable LHL/HIB pads
47
GND
-
GND
Ground
48
GND
-
GND
Ground
49
BT_RF_OUT
I/O
Bluetooth Antenna
50
GND
-
GND
Ground
51
BT_RF_IN
I/O
(SP3T)
BT/WiFi one antenna: Routed to
BT_RF_OUT
Separate BT/WiFi antenna: connect to
50ohm terminal.
52
GND
-
GND
Ground
53
GND
-
GND
Ground
54
RF_SW_CTRL_6
O
RF_SW_CTRL_6
NC
55
RF_SW_CTRL_10
O
RF_SW_CTRL_10
Programmable RF switch-control lines
56
RF_SW_CTRL_5
O
RF_SW_CTRL_5
NC
57
GND
-
GND
Ground
58
ANT0
I/O
59
GND
-
GND
Ground
60
GND
-
GND
Ground
61
WL_GPIO_15
I/O
GPIO_15
Programmable GPIO lines
62
WL_GPIO_13
I/O
GPIO_13
Programmable GPIO lines
63
WL_GPIO_12
I/O
GPIO_12
Programmable GPIO lines
64
WL_GPIO_14
I/O
GPIO_14
Programmable GPIO lines
65
GND
-
GND
Ground
66
WL_GPIO_5
I/O
GPIO_5
Programmable GPIO lines
67
WL_GPIO_4
I/O
GPIO_4
Programmable GPIO lines
68
WL_GPIO_3
I/O
GPIO_3
Programmable GPIO lines
69
WL_GPIO_2
I/O
GPIO_2
Programmable GPIO lines
70
NC
I
JTAG_SEL
Wi-Fi JTAG interface is intended to be used
by Cypress's internal teams only
71
WL_GPIO_6
I/O
GPIO_6
Programmable GPIO lines
72
GND
-
GND
Ground
73
GND
-
GND
Ground
74
SFL_IO0
I/O
SFL_IO0
SFLASH data line 0
75
SFL_IO3
I/O
SFL_IO3
SFLASH data line 3
76
SFL_IO2
I/O
SFL_IO2
SFLASH data line 2
77
SFL_CLK
O
SFL_CLK
SFLASH clock
78
SFL_IO1
I/O
SFL_IO1
SFLASH data line 1
79
SFL_CS
O
SFL_CS
SFLASH chip select
Preliminary Specification Number : SP-9B1LV-M
10 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
No.
Pin name
Type
Connection to
IC pin name
Description
80
EXT_LPO
I
LPO_IN
External sleep-clock input(32.768kHz)
81
CLK_REQ
I/O
CLK_REQ
Reference clock request
82
BT_PCM_OUT
O
BT_PCM_OUT
PCM data output
83
BT_PCM_SYNC
I/O
BT_PCM_SYNC
PCM sync, can be master (output)
or slave (input)
84
BT_PCM_IN
I
BT_PCM_IN
PCM data input
85
BT_PCM_CLK
I/O
BT_PCM_CLK
PCM clock, can be master (output)
or slave (input)
86
BT_I2S_WS
I/O
BT_I2S_WS
I2S serial word select
87
BT_I2S_CLK
I/O
BT_I2S_CLK
I2S serial clock
88
BT_I2S_DI
I
BT_I2S_DI
I2S serial data input
89
BT_I2S_DO
O
BT_I2S_DO
I2S serial data output
90
BT_GPIO_2
I/O
BT_GPIO_2
Bluetooth general-purpose I/Os
91
BT_GPIO_5
I/O
BT_GPIO_5
Bluetooth general-purpose I/Os
92
BT_GPIO_4
I/O
BT_GPIO_4
Bluetooth general-purpose I/Os
93
BT_GPIO_3
I/O
BT_GPIO_3
Bluetooth general-purpose I/Os
94-106
GND
-
GND
Ground
Preliminary Specification Number : SP-9B1LV-M
11 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
8. ABSOLUTE MAXIMUM RATINGS*2)
Parameter
min.
max.
Unit
Storage Temperature
-40
85
deg.C
Supply Voltage
VBAT
-0.5
5.0
V
VDDIO
-0.5
2.2
V
VDDIO_SFL
-0.5
4.1
V
*2) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation
is not implied under these conditions. Exposure to absolute ratings for extended periods of time
may adversely affect reliability. No damage assuming only one parameter is set at limit at a time
with all other parameters are set within operating condition.
9. OPERATING CONDITION*3)
Parameter
min.
typ.
max.
unit
Operating Temperature
-20
25
+70
deg.C
Supply Voltage
VBAT
3.2
-
4.4
V
VDDIO
1.62
1.8
1.98
V
VDDIO_SFL
1.62/2.97
1.8/3.3
1.98/3.46
V
*3) Functionality is guaranteed but the specifications require the derating at over-temperatures,
over-voltage condition.
10. External LPO Signal Requirement
Parameter
External LPO Clock
Unit
Nominal input frequency
32.768
kHz
Frequency accuracy
+/-250
ppm
Duty cycle
30-70
%
Input signal amplitude
500 – 1800
mVp-p
Signal type
Square-wave or sine-wave
-
Input impedance*4)
> 100k
ohm
*4) When power is applied or switch off
Preliminary Specification Number : SP-9B1LV-M
12 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
11. POWER ON SEQUENCE
-VBAT should not rise 10%-90%faster than 40 microsecond.
-VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be
held high before VBAT is high.
11.1. Power On Sequence for WLAN ON and BT ON
32.768kHz Sleep Clock
VBAT
VDDIO
WL_REG_ON
BT_REG_ON
90% of VH
~2 Sleep cycle
11.2. Power On Sequence for WLAN ON and BT Off
32.768kHz Sleep Clock
VBAT
VDDIO
WL_REG_ON
BT_REG_ON
90% of VH
~2 Sleep cycle
VDDIO
VDDIO
Preliminary Specification Number : SP-9B1LV-M
13 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
11.3. Power On Sequence for WLAN OFF and BT ON
32.768kHz Sleep Clock
VBAT
VDDIO
WL_REG_ON
BT_REG_ON
90% of VH
~2 Sleep cycle
11.4. Power On Sequence for WLAN OFF and BT OFF
32.768kHz Sleep Clock
VBAT
VDDIO
WL_REG_ON
BT_REG_ON
VDDIO
VDDIO
Preliminary Specification Number : SP-9B1LV-M
14 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
12. Digital I/O Requirements
Digital I/O Pins
Sym
min.
typ.
max.
unit
For VDDIO=1.8V:
Input high voltage
VIH
0.65xVDDIO
-
-
V
Input low voltage
VIL
-
-
0.35xVDDIO
V
Output high voltage@2mA
VOH
VDDIO-0.45
-
-
V
Output low voltage@2mA
VOL
-
-
0.45
V
BT/WL_REG_ON
Sym
min.
typ.
max.
unit
Input high voltage
VIH
1
-
4.4
V
Input low voltage
VIL
VSS
-
0.3
V
Pull-down resistance(internal)
RPD
-
50
-
k
Leakage discharged Current
ILEAK_DIS
-
28
-
nA
REG OFF time
TREG_OFF
2
-
-
ms
Preliminary Specification Number : SP-9B1LV-M
15 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
13. INTERFACE TIMING AND AC CHARACTERISTICS
13.1. Bluetooth UART Timing
BT_UART_CTS_N
BT_UART_TXD
BT_UART_RXD
BT_UART_RTS_N
Midpoint of STOP bit
3
1
Midpoint of STOP bit
2
Reference
Description
Min
Typ
Max
Unit
1
Delay time, UART_CTS low to UART_TXD valid
-
-
1.5
Bit periods
2
Setup time, UART_CTS high before midpoint of stop bit
-
-
0.5
Bit periods
3
Delay time, midpoint of stop bit to UART_RTS high
-
-
0.5
Bit periods
Preliminary Specification Number : SP-9B1LV-M
16 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
13.2. SDIO Timing
13.2.1. SDIO Default Mode Timing
CLK
Output
Input
fPP
tWH
tISU
tIH
tODLY
(min)
tWL
tTHL
tTLH
tODLY
(max)
SDIO Bus Timing(a) parameters (default Mode)
Parameter
Symbol
Min
Typ
Max
Unit
SDIO CLK (All values are referred to minimum VIH and maximum VIL(b)
Frequency-Data Transfer Mode
fPP
0
-
25
MHz
Frequency-Identification Mode
fOD
0
-
400
kHz
Clock Low Time
tWL
10
-
-
ns
Clock High Time
tWH
10
-
-
ns
Clock Rise Time
tTLH
-
-
10
ns
Clock low Time
tTHL
-
-
10
ns
Inputs: CMD, DAT (referenced to CLK)
Input Setup Time
tISU
5
-
-
ns
Input Hold Time
tIH
5
-
-
ns
Outputs: CMD, DAT (referenced to CLK)
Output Delay time-Data Transfer Mode
tODLY
0
-
14
ns
Output Delay time-Identification Mode
tODLY
0
-
50
ns
(a). Timing is based on CL < 40pF load on CMD and Data.
(b). Min (Vih) = 0.7*VDDIO and max (Vil) = 0.2*VDDIO.
SDIO_
Preliminary Specification Number : SP-9B1LV-M
17 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
13.2.2. SDIO High-Speed Mode Timing
CLK
Input
Output
fPP
tWH
tISU
tIH
tOH
tWL
tTHL
tTLH
tODLY
50% VDD
SDIO Bus Timing(a) parameters (High-Speed Mode)
Parameter
Symbol
Min
Typ
Max
Unit
SDIO CLK (All values are referred to minimum VIH and maximum VIL(b)
Frequency-Data Transfer Mode
fPP
0
-
50
MHz
Frequency-Identification Mode
fOD
0
-
400
kHz
Clock Low Time
tWL
7
-
-
ns
Clock High Time
tWH
7
-
-
ns
Clock Rise Time
tTLH
-
-
3
ns
Clock low Time
tTHL
-
-
3
ns
Inputs: CMD, DAT (referenced to CLK)
Input Setup Time
tISU
6
-
-
ns
Input Hold Time
tIH
2
-
-
ns
Outputs: CMD, DAT (referenced to CLK)
Output Delay time-Data Transfer Mode
tODLY
-
-
14
ns
Output Hold time
tOH
2.5
-
-
ns
Total System Capacitance (each line)
CL
-
-
40
pF
(a). Timing is based on CL < 40pF load on CMD and Data.
(b). Min (Vih) = 0.7*VDDIO and max (Vil) = 0.2*VDDIO
SDIO_
Preliminary Specification Number : SP-9B1LV-M
18 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
13.2.3. SDIO BUS Timing Specifications in SDR Modes
Clock Timing
SDIO_CLK
tCR
tCF
tCR
tCLK
SDIO Bus Clock Timing Parameters (SDR Modes)
Parameter
Symbol
Min
Max
Unit
Comments
-
tCLK
40
-
ns
SDR12 mode
20
-
ns
SDR25 mode
-
tCR,tCF
-
0.2 x
tCLK
ns
tCR,tCF<2.00ns(max)@100MHz,cCARD=10pF
Clock duty
-
30
70
%
-
cycle
Card Input Timing
CMD input
DAT[3:0] input
tIS
tIH
SDIO_CLK
SDIO Bus Input Timing Parameters ( SDR Modes)
Symbol
Min
Max
Unit
Comments
SDR50 Mode
tIS
3.0
-
ns
cCARD = 10pF,VCT = 0.975V
tIH
0.8
-
ns
cCARD = 5pF,VCT = 0.975V
Preliminary Specification Number : SP-9B1LV-M
19 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Card Output Timing
SDIO Bus Output Timing (SDR Modes up to 50MHz)
CMD input
DAT[3:0] input
tODLY
tOH
SDIO_CLK
tCLK
SDIO Bus Output Timing Parameters ( SDR Modes up to 50MHz)
Symbol
Min
Max
Unit
Comments
tODLY
-
14.0
ns
tCLK ≧ 20ns CL = 40pF using for SDR12,SDR25
tOH
1.5
-
ns
Hold time at the tODLY(min) CL = 15pF
Preliminary Specification Number : SP-9B1LV-M
20 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14. DC / RF Characteristics
14.1. DC/RF Characteristics for IEEE802.11b - 2.4GHz
Specification
IEEE802.11b
Mode
DSSS / CCK
Channel Frequency
2412 - 2472MHz
Data rate
1, 2, 5.5, 11Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=17dBm, 11Mbps mode unless otherwise specified.
Items
Contents
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*5)
-
200
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics *5)-
min.
typ.
max.
unit
2. Output Power
15
17
19
dBm
3. Spectrum Mask margin
1) 1st side lobes(-30dBr)
0
-
-
dB
2) 2nd side lobes(-50dBr)
0
-
-
dB
4. Power-on and Power-down ramp
-
2.0
μsec
5. RF Carrier Suppression
15
-
-
dB
6. Modulation Accuracy (EVM)
-
-
35
%
7.Frequency tolerance
-20
20
ppm
8. Out band Spurious Emissions
1) 30-1000MHz
-
-
-36
dBm
2) 1000-12750MHz
-
-
-30
dBm
3) 1800-1900MHz
-47
dBm
4) 5150-5300MHz
-
-
-47
dBm
- Rx Characteristics -
min.
typ.
max.
unit
9. Minimum Input Level Sensitivity
-
-
-76
dBm
10. Adjacent Channel Rejection
(FER < 8%)
35
-
-
dB
*5): Defined when output power setting is 17dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
21 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.2. DC/RF Characteristics for IEEE802.11g - 2.4GHz
Specification
IEEE802.11g
Mode
OFDM
Channel Frequency
2412 - 2472MHz
Data rate
6, 9, 12, 18, 24, 36, 48, 54Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=14dBm, 54Mbps mode unless otherwise specified.
Items
Contents
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*6)
-
150
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics*6) -
min.
typ.
max.
unit
2. Output Power
12
14
16
dBm
3. Spectrum Mask margin
1) 9MHz to 11MHz (0~ -20dBr)
0
-
-
dB
2) 11MHz to 20MHz (-20~ -28dBr)
0
-
-
dB
3) 20MHz to 30MHz (-28~ -40dBr)
0
-
-
dB
4) 30MHz to 33MHz (-40dBr)
0
-
-
dB
4. Constellation Error (EVM)
-
-
-25
dB
5.Frequency tolerance
-20
20
ppm
6. Out band Spurious Emissions
1) 30-1000MHz
-
-
-36
dBm
2) 1000-12750MHz
-
-
-30
dBm
3) 1800-1900MHz
-47
dBm
4) 5150-5300MHz
-
-
-47
dBm
- Rx Characteristics -
min.
typ.
max.
unit
7. Minimum Input Level Sensitivity
-
-
-65
dBm
8. Adjacent Channel Rejection
(PER < 10%)
-1
-
-
dB
*6): Defined when output power setting is 14dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
22 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.3. DC/RF Characteristics for IEEE802.11n – 2.4GHz
Specification
IEEE802.11n
Mode
OFDM
Channel Frequency
2412 - 2472MHz
Data rate
6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=13dBm, MCS7 unless otherwise specified.
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*7)
-
140
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics*7) -
min.
typ.
max.
unit
2. Output Power
11
13
15
dBm
3. Spectrum Mask
1) 9MHz to 11MHz (0 ~ -20dBr)
0
-
-
dB
2) 11MHz to 20MHz (-20 ~ -28dBr)
0
-
-
dB
3) 20MHz to 30MHz (-28 ~ -45dBr)
0
-
-
dB
4) 30MHz to 33MHz (-45dBr)
0
-
-
dB
4. Constellation Error (EVM)
-
-
-27
dB
5.Frequency tolerance
-20
20
ppm
6. Out band Spurious Emissions
1) 30-1000MHz
-
-
-36
dBm
2) 1000-12750MHz
-
-
-30
dBm
3) 1800-1900MHz
-47
dBm
4) 5150-5300MHz
-
-
-47
dBm
- Rx Characteristics -
min.
typ.
max.
unit
6. Minimum Input Level Sensitivity
-
-
-64
dBm
7. Adjacent Channel Rejection
(PER < 10%)
-2
-
-
dB
*7): Defined when output power setting is 13dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
23 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.4. DC/RF Characteristics for IEEE802.11a - 5GHz
Specification
IEEE802.11a
Mode
OFDM
Channel Frequency
5180 - 5825MHz
Data rate
6, 9, 12, 18, 24, 36, 48, 54Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=13dBm, 54Mbps unless otherwise specified.
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*8)
-
230
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics*8) -
min.
typ.
max.
unit
2. Output Power
11
13
15
dBm
3. Spectrum Mask
1) 9MHz to 11MHz (0~ -20dBr)
0
-
-
dB
2) 11MHz to 20MHz (-20~ -28dBr)
0
-
-
dB
3) 20MHz to 30MHz (-28~ -40dBr)
0
-
-
dB
4) 30MHz to 33MHz (-40dBr)
0
-
-
dB
4. Constellation Error (EVM)
-
-
-25
dB
5.Frequency tolerance
-20
20
ppm
- Rx Characteristics -
min.
typ.
max.
unit
6. Minimum Input Level Sensitivity
-
-
-65
dBm
7. Adjacent Channel Rejection
(PER < 10%)
-1
-
-
dB
*8): Defined when output power setting is 13dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
24 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.5. DC/RF Characteristics for IEEE802.11n(HT20) - 5GHz
Specification
IEEE802.11n
Mode
OFDM
Channel Frequency
5180 - 5825MHz
Data rate
6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=12dBm, MCS7 unless otherwise specified.
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*9)
-
210
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics*9) -
min.
typ.
max.
unit
2. Output Power
10
12
14
dBm
3. Spectrum Mask margin
1) 9MHz to 11MHz (0~ -20dBr)
0
-
-
dB
2) 11MHz to 20MHz (-20~ -28dBr)
0
-
-
dB
3) 20MHz to 30MHz (-28~ -45dBr)
0
-
-
dB
4) 30MHz to 33MHz (-45dBr)
0
-
-
dB
4. Constellation Error (EVM)
-
-
-27
dB
5.Frequency tolerance
-20
20
ppm
- Rx Characteristics -
min.
typ.
max.
unit
6. Minimum Input Level Sensitivity
-
-
-64
dBm
7. Adjacent Channel Rejection
(PER < 10%)
-2
-
-
dB
*9): Defined when output power setting is 12dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
25 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.6. DC/RF Characteristics for IEEE802.11ac(VHT20) - 5GHz
Specification
IEEE802.11ac
Mode
OFDM
Channel Frequency
5180 - 5825MHz
Data rate
6.5, 13, 19.5, 26, 39, 52, 58.5, 65, 78Mbps
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V,
Output power setting=10dBm, MCS8 unless otherwise specified.
- DC Characteristics -
min.
typ.
max.
unit
1. DC current
1) Tx mode (1024byte, 20usec interval)
*10)
-
190
-
mA
2) Rx mode
-
20
-
mA
- Tx Characteristics*10) -
min.
typ.
max.
unit
2. Output Power
8
10
12
dBm
3. Spectrum Mask margin
1) 9MHz to 11MHz (0~ -20dBr)
0
-
-
dB
2) 11MHz to 20MHz (-20~ -28dBr)
0
-
-
dB
3) 20MHz to 30MHz (-28~ -45dBr)
0
-
-
dB
4) 30MHz to 33MHz (-45dBr)
0
-
-
dB
4. Constellation Error (EVM)
-
-
-32
dB
5.Frequency tolerance
-20
20
ppm
- Rx Characteristics -
min.
typ.
max.
unit
6. Minimum Input Level Sensitivity
-
-
-59
dBm
7. Adjacent Channel Rejection
(PER < 10%)
-7
-
-
dB
*10): Defined when output power setting is 10dBm at Murata module antenna pad
Preliminary Specification Number : SP-9B1LV-M
26 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.7. DC/RF Characteristics for Bluetooth
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V
Items
Contents
Bluetooth specification (power class)
Version 5.0 + EDR (Class1)
Channel frequency (spacing)
2402 to 2480 MHz (1MHz)
Current Consumption
Min.
Typ.
Max.
unit
(a) Tx=Rx=DH5 (fully occupied)
-
25
-
mA
(b) Tx=Rx=2DH5 (fully occupied)
-
22
-
mA
(c) Tx=Rx=3DH5 (fully occupied)
-
22
-
mA
Transmitter
Min.
Typ.
Max.
Unit
Output Power@DH5
6
-
13
dBm
Frequency range
2400
-
2483.5
MHz
20dB bandwidth
-
1
MHz
Adjacent Channel Power *11)
(a) [M-N] =2
-
-
-20
dBm
(b) [M-N] ≥3
-
-
-40
dBm
Modulation characteristics
(a) Modulation Δf1avg
140
-
175
kHz
(b) Modulation Δf2max
115
-
kHz
(c) Modulation Δf2avg / Δf1avg
0.8
-
-
Carrier Frequency Drift
(a) 1slot
-25
-
25
kHz
(b) 3slot / 5slot
-40
-
40
kHz
(c) Maximum drift rate
-
20
kHz/50us
EDR Relative Power
-4
-
1
dB
EDR Carrier Frequency Stability and
Modulation Accuracy
(a) ωi
-75
-
75
kHz
(b) ωi+ωo
-75
-
75
kHz
(c) ωo
-10
-
10
kHz
(d) RMS DEVM (DQPSK)
-
-
20
%
(e) Peak DEVM (DQPSK)
-
-
35
%
(f) 99% DEVM (DQPSK)
-
-
30
%
(g) RMS DEVM (8DPSK)
-
-
13
%
(h) Peak DEVM (8DPSK)
-
-
25
%
(i) 99% DEVM (8DPSK)
-
-
20
%
Spurious Emissions
(a) 10MHz≦f<2387MHz
-
-
-36
dBm
(b) 2387MHz≦f<2400MHz
-
-
-30
dBm
(c) 2483.5MHz<f≦2496.5MHz
-47
dBm
(d) 2496.5MHz<f≦8GHz
-
-
-47
dBm
Receiver
Min.
Typ.
Max.
unit
BDR Sensitivity (BER<0.1%)
-
-
-80
dBm
EDR Sensitivity (BER<0.007%)@8DPSK
-
-
-77
dBm
C/I Performance (BER<0.1%) *12)
(a) co-channel
-
-
11
dB
(b) 1MHz
-
-
0
dB
(c) 2MHz
-
-
-30
dB
(d) 3MHz
-
-
-40
dB
(e) image (+4MHz)
-
-
-9
dB
(f) image +/- 1MHz
-
-
-20
dB
Maximum Input Level (BER<0.1%)
-20
-
-
dBm
*11): Up to three spurious responses within Bluetooth limits are allowed.
*12): Up to five spurious responses within Bluetooth limits are allowed.
Preliminary Specification Number : SP-9B1LV-M
27 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
14.8. DC/RF Characteristics for Bluetooth (LE)
Conditions : 25deg.C, VBAT=3.3V, VDDIO= 1.8V
Items
Contents
Bluetooth specification (power class)
Version 5.0(LE)
Channel frequency (spacing)
2402 to 2480 MHz (2MHz)
Number of RF Channel
40
Item / Condition
Min.
Typ.
Max.
Unit
Center Frequency
2402
-
2480
MHz
Channel Spacing
-
2
-
MHz
Number of RF channel
-
40
-
-
Output power
2
-
9
dBm
Modulation Characteristics
1) Δf1avg
225
-
275
kHz
2) Δf2max (at 99.9%)
185
-
-
kHz
3) Δf2avg / Δf1avg
0.8
-
-
-
Carrier frequency offset and drift
1) Frequency offset
-
-
150
kHz
2) Frequency drift
-
-
50
kHz
3) Drift rate
-
-
20
kHz
Receiver sensitivity (PER < 30.8%)
-
-
-70
dBm
Maximum input signal level (PER < 30.8%)
-10
-
-
dBm
PER Report Integrity (-30dBm input)
50
-
65.4
%
Preliminary Specification Number : SP-9B1LV-M
28 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
15. LAND PATTERN (TOP VIEW)
* To avoid the short-circuit between the side shielding and a solder on the module land after the reflow,
please locate the module land away from module outline as above figure.
Preliminary Specification Number : SP-9B1LV-M
29 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
16. REFERENCE CIRCUIT
1
2
3
4
5
6
A B C D E F G H
1
2
3
4
5
6
A B C D E F G H
GND
4.7uF
GND
0.1uF
VBAT
VDDOUT_VDDIO
VDDIO_SFL connect to VDDOUT_VDDIO
GND
0.1uF
LBEE59B1LV
GND
GND GND
GND
BT_GPIO_3
BT_GPIO_4
BT_GPIO_5
BT_GPIO_2
RF_SW_CTRL_5
RF_SW_CTRL_10
RF_SW_CTRL_6
ANT0
GND
SDIO_DATA_2
SDIO_DATA_1
SDIO_DATA_0
SDIO_DATA_3
SDIO_CMD
SDIO_CLK
VDDOUT_VDDIO
BT_HOST_WAKE
WL_HOST_WAKE
BT_REG_ON
WL_REG_ON
RF_SW_CTRL_8
RF_SW_CTRL_12
RF_SW_CTRL_11
WL_GPIO_15
BT_I2S_DO
BT_I2S_DI
BT_I2S_CLK
BT_I2S_WS
BT_PCM_CLK
BT_PCM_IN
BT_PCM_SYNC
BT_PCM_OUT
CLK_REQ
P1
P0
P12
P6
P13
P11
P9
BT_UART_RTS
BT_UART_CTS
BT_UART_RXD
BT_UART_TXD
VDDIO
GND
0.1uF
resistors or through proper programming of the SDIO host's internal pull-ups.
This requirement must be met during all operating states either through the use of external pull-up
GND
32.768kHz
ANT0
ANT :WLAN
ANT :BT
BT_RF_OUT
BT_RF_OUT
BT_RF_IN
BT_RF_IN
GND
ANT0
BT_RF_IN
BT_RF_OUT
ANT :WLAN/BT
RF line :
Separate antennaRF line :
(*1)
(*1) Pull-ups in the 10kOhm to 100kOhm range are required on the four DATA lines and the CMD line.
(*2) Put matching component's land near the ANT terminals.
(*2)
(*2)
(*2)
GND
Single antenna (Murata Default setting)
GND(1)
1
GND(2)
2
GND(3)
3
VDDIO_SFL
4
BT_HOST_WAKE
5
GND(6)
6
WL_HOST_WAKE
7
BT_REG_ON
9
WL_REG_ON
10
GND(11)
11
VOUT_3P3
12
VBAT(13)
13
VBAT(14)
14
GND(15)
15
RF_SW_CTRL_8
16
RF_SW_CTRL_12
17
RF_SW_CTRL_11
18
GND(19)
19
GND(59)
59
GND(60)
60
WL_GPIO_15
61
GND(103) 103
BT_RF_OUT 49
GND(50) 50
BT_RF_IN 51
GND(52) 52
GND(53) 53
RF_SW_CTRL_6 54
RF_SW_CTRL_10 55
RF_SW_CTRL_5 56
GND(57) 57
ANT0 58
BT_GPIO_2 90
BT_GPIO_5 91
BT_GPIO_4 92
BT_GPIO_3 93
GND(94) 94
GND(104) 104
GND(105) 105
GND(106) 106
GND(102) 102
GND(101) 101
BT_I2S_DO 89
BT_I2S_DI 88
BT_I2S_CLK 87
BT_I2S_WS 86
BT_PCM_CLK 85
BT_PCM_IN 84
BT_PCM_SYNC 83
BT_PCM_OUT 82
CLK_REQ 81
EXT_LPO 80
SFL_CS 79
SFL_IO1 78
SFL_CLK 77
GND(48) 48
GND(47) 47
P1 46
P0 45
P12 44
P7 43
P8 42
P6 41
P5 40
P13 39
P11 38
P9 37
GND(36) 36
VDDIO 35
BT_UART_CTS 34
BT_UART_RTS 33
BT_UART_RXD 32
BT_UART_TXD 31
GND(30) 30
GND(100)
100
GND(99)
99
GND(98)
98
SFL_IO2
76
SFL_IO3
75
SFL_IO0
74
GND(73)
73
GND(72)
72
VDDOUT_VDDIO
28
GND(27)
27
SDIO_CMD
26
SDIO_DATA_1
22
SDIO_DATA_0
23
SDIO_CLK
24
SDIO_DATA_3
25
SDIO_DATA_2
21
GND(20)
20
GND(97)
97
GND(96)
96
GND(95)
95
GND(65)
65
WL_GPIO_14
64
WL_GPIO_1
8
BT_GPIO_0
29
WL_GPIO_13
62
WL_GPIO_12
63
WL_GPIO_5
66
WL_GPIO_4
67
WL_GPIO_3
68
WL_GPIO_2
69
NC
70
WL_GPIO_6
71
(Type1LV)
WL_GPIO_13
WL_GPIO_12
WL_GPIO_14
WL_GPIO_5
WL_GPIO_4
WL_GPIO_3
WL_GPIO_2
WL_GPIO_6
WL_GPIO_1
BT_GPIO_0
P8
P5(BT_DEV_WAKE)
P7(WL_DEV_WAKE)
Preliminary Specification Number : SP-9B1LV-M
30 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
17. TAPE AND REEL PACKING
(1) Dimensions of Tape (Plastic tape)
(2) Dimensions of Reel
2.0±0.1
1.75±0.10
0.30±0.05
1.55 ±0.05
16.0±0.1
11.5±0.1
1.5+0.1/-0.0
24.0+0.3/-0.1
Feeding direction
4
.0±0.1
7.6±0.05
2.0+0.1/-0.0
10.5±0.05
13.0±0.2
2.0±0.5
25.4±1.0
30.4 max.
100
330
Preliminary Specification Number : SP-9B1LV-M
31 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
(3) Taping Diagrams [1] Feeding Hole : As specified in (1)
[2] Hole for chip : As specified in (1)
[3] Cover tape : 62 um in thickness
[4] Base tape : As specified in (1)
(4) Leader and Tail tape
Feeding Hole
Chip
Feeding Direction
Pin 1 Marking
Tail tape
(No components)
40 to 200mm
Components
No components
150mm min.
Leader tape
(Cover tape alone)
250mm min.
Feeding direction
[2]
[3]
[4]
[3]
[1]
Preliminary Specification Number : SP-9B1LV-M
32 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
(5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled
toward the user.
(6) The cover tape and base tape are not adhered at no components area for 250mm min.
(7) Tear off strength against pulling of cover tape: 5N min.
(8) Packaging unit : 1000pcs./ reel
(9) material - Base tape : Plastic
Real : Plastic
Cover tape, cavity tape and reel are made the anti-static processing.
(10) Peeling of force: 1.1N max. in the direction of peeling as shown below.
(11) PACKAGE (Humidity proof packing)
Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant
and the humidity indicator.
　湿度
インジケ－タ
乾燥剤
表示ラべル
防湿梱包袋
表示ラベル
Label
Label
Desiccant
Humidity
Indicator
Anti-humidity
Plastic Bag
165 to 180 °
1.1 N max.
Base tape
Cover tape
Preliminary Specification Number : SP-9B1LV-M
33 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
18. NOTICE
18.1. Storage Conditions:
Please use this product within 6month after receipt.
- The product shall be stored without opening the packing under the ambient temperature from 5 to
35deg.C and humidity from 20 to 70%RH.
(Packing materials, in particular, may be deformed at the temperature over 40deg.C.)
- The product left more than 6months after reception, it needs to be confirmed the solderbility before
used.
- The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.).
- Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp
object and dropping the product, shall not be applied in order not to damage the packing materials.
This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020)
- After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be
used within 168hours.
- When the color of the indicator in the packing changed, the product shall be baked before soldering.
Baking condition: 125+5/-0deg.C, 24hours, 1time
The products shall be baked on the heat-resistant tray because the material (Base Tape, Reel Tape and
Cover Tape) are not heat-resistant.
18.2. Handling Conditions:
Be careful in handling or transporting products because excessive stress or mechanical shock may
break products.
Handle with care if products may have cracks or damages on their terminals, the characteristics of
products may change. Do not touch products with bear hands that may result in poor solder ability and
destroy by static electrical charge.
18.3. Standard PCB Design (Land Pattern and Dimensions):
All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern
should be provided between IN and OUT terminals. Please refer to the specifications for the standard
land dimensions.
The recommended land pattern and dimensions is as Murata's standard. The characteristics of
products may vary depending on the pattern drawing method, grounding method, land dimensions,
land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to
verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand.
18.4. Notice for Chip Placer:
When placing products on the PCB, products may be stressed and broken by uneven forces from a
worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to
follow the specifications for the maintenance of the chip placer being used. For the positioning of
products on the PCB, be aware that mechanical chucking may damage products.
Preliminary Specification Number : SP-9B1LV-M
34 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
18.5. Soldering Conditions:
The recommendation conditions of soldering are as in the following figure.
Soldering must be carried out by the above mentioned conditions to prevent products from damage.
Set up the highest temperature of reflow within 260 °C. Contact Murata before use if concerning other
soldering conditions.
Reflow soldering standard conditions (Example)
Please use the reflow within 2 times.
Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less.
18.6. Cleaning:
Since this Product is Moisture Sensitive, any cleaning is not recommended. If any cleaning process is
done the customer is responsible for any issues or failures caused by the cleaning process.
18.7. Operational Environment Conditions:
Products are designed to work for electronic products under normal environmental conditions (ambient
temperature, humidity and pressure). Therefore, products have no problems to be used under the
similar conditions to the above-mentioned. However, if products are used under the following
circumstances, it may damage products and leakage of electricity and abnormal temperature may
occur.
- In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx etc.).
- In an atmosphere containing combustible and volatile gases.
- Dusty place.
- Direct sunlight place.
- Water splashing place.
- Humid place where water condenses.
- Freezing place.
If there are possibilities for products to be used under the preceding clause, consult with Murata before
actual use.
As it might be a cause of degradation or destruction to apply static electricity to products, do not apply
static electricity or excessive voltage while assembling and measuring.
Within 120s
Pre-heating
time(s)
220 deg.C
Within 60s
Cooling down
Slowly
180 deg.C
150 deg.C
250 deg.C
Within 10s
Tpeak-5deg.C
Preliminary Specification Number : SP-9B1LV-M
35 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
18.8. Input Power Capacity:
Products shall be used in the input power capacity as specified in this specifications.
Inform Murata beforehand, in case that the components are used beyond such input power capacity
range.
Preliminary Specification Number : SP-9B1LV-M
36 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
19. PRECONDITION TO USE OUR PRODUCTS
PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS.
Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the
specifications of our product when our product is mounted to your product.
All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that
our product is used for the purpose, under the condition and in the environment specified in this specification. You are
requested not to use our product deviating from the condition and the environment specified in this specification.
Please note that the only warranty that we provide regarding the products is its conformance to the specifications
provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such
products, which are caused under the conditions other than those specified in this specification.
WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY
ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS.
You agree that you will use any and all software or program code (including but not limited to hcd, firmware, nvram, and
blob) we may provide or to be embedded into our product (“Software”) provided that you use the Software bundled with
our product. YOU AGREE THAT THE SOFTWARE SHALL BE PROVIDED TO YOU “AS- IS” BASIS, MURATA MAKES
NO REPRESENTATIONS OR WARRANTIES THAT THE SOFTWARE IS ERROR-FREE OR WILL OPERATE
WITHOUT INTERRUPTION. AND MORE, MURATA MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY
KIND WHETHER EXPRESS OR IMPLIED WITH RESPECT TO THE SOFTWARE. MURATA EXPRESSLY DISCLAIM
ANY AND ALL WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
NOR THE WARRANTY OF TITLE OR NON-INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS.
You shall indemnify and hold harmless us, our affiliates and our licensor from and against any and all claims,
costs, expenses and liabilities (including attorney’s fees), which arise in connection with the using the
Software.
The product shall not be used in any application listed below which requires especially high reliability for the prevention
of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that,
if you use our products in such applications, we will not be responsible for any failure to meet such requirements.
Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS,
DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY
FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS AND THE SOFTWARE IN SUCH APPLICATIONS.
- Aircraft equipment. - Aerospace equipment - Undersea equipment.
- Power plant control equipment - Medical equipment.
- Transportation equipment (vehicles, trains, ships, elevator, etc.).
- Traffic signal equipment. - Disaster prevention / crime prevention equipment.
-Burning / explosion control equipment
- Application of similar complexity and/ or reliability requirements to the applications listed in the above.
We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our
product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by
the regulations and laws in the world.
We do not warrant or represent that any license, either express or implied, is granted under any our patent right,
copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in
which our products or services are used. Information provided by us regarding third-party products or services does not
constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such
information may require a license from a third party under the patents or other intellectual property of the third party, or a
license from us under our patents or other intellectual property.
Please do not use our products, our technical information and other data provided by us for the purpose of developing of
mass-destruction weapons and the purpose of military use.
Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations",
etc.
Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials
and/or components from our suppliers.
By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your
company and that you understand and accept the validity of the contents herein. When you are not able to return the
signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or
approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer
acknowledges that engineering samples may deviate from specifications and may contain defects due to their
development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability
for damages caused by
- the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the
product to be sold by you,
-deviation or lapse in function of engineering sample,
-improper use of engineering samples.
We disclaim any liability for consequential and incidental damages.
If you can’t agree the above contents, you should inquire our sales.
Preliminary Specification Number : SP-9B1LV-M
37 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
APPENDIX
Preliminary Specification Number : SP-9B1LV-M
38 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Annex A
Certification
For FCC
Model Name: Type1LV
FCC ID: VPYLBEE59B1LV
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device maynot cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
●The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID:VPYLBEE59B1LV
Or
Contains FCC ID: VPYLBEE59B1LV
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device maynot cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
*If it can not be described on the host product, it must be listed on both the host product manual and on the
host product package or removable label.
●The following statements must be described on the user manual of the host device of this module;
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will
be on only while one of the aforementioned packets is being transmitted. In other words, this
device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
Frequency Tolerance: ±20 ppm
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
●When installing it in a mobile equipment. Please describe the following warning to the manual.
If mobile equipment use only BT/BLE or low power Wi-Fi.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment
should be installed and operated keeping the radiator at least 20cm or more away from
person’s body.
In the case of conditions other than the above
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of
the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated
keeping the radiator at least 20cm or more away from person’s body.
●When installing it in a portable equipment. Please describe the following warning to the manual.
Preliminary Specification Number : SP-9B1LV-M
39 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
The available scientific evidence does not show that any health problems are associated with
using low power wireless devices. There is no proof, however, that these low power wireless
devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency
energy (RF) in the microwave range while being used. Whereas high levels of RF can produce
health effects (by heating tissue), exposure of low-level RF that does not produce heating
effects causes no known adverse health effects. Many studies of low-level RF exposures have
not found any biological effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by additional research. LBEE59B1LV
has been tested and found to comply with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
It is necessary to take a SAR test with your set mounting this module .
Class II permissive change application is necessary using the SAR report. Please contact Murata.
Note)
Portable equipment : Equipment for which the spaces between human body and antenna are used within
20cm.
Mobile equipment : Equipment used at position in which the spaces between human body and antenna
exceeded 20cm.
●Antenna
Please refer to the ‘Certified Antenna information’ document supplied by Murata
or please contact Murata for the detail designation of how to design the Antenna trace.
●Installation procedure
Supply Voltage
Min.
Typ.
Max.
unit
Supply
Voltage
VBAT
3.1
3.3
3.5
V
VIO
1.8 or 3.3
V
*VIO don’t influence the RF characteristic.
RF Power
2.4GHz WLAN
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11b
All Rate
1 - 11
19
IEEE 802.11g
6/9 Mbps
1 - 11
19
12/18/24 Mbps
1 - 11
18
36/48 Mbps
1 - 11
17
54 Mbps
1 - 11
16
IEEE 802 11n(HT20)
MCS0 - 2
1 – 11
19
MCS3
1 – 11
18
MCS4 – 5
1 – 11
17
MCS6
1 – 11
16
MCS7
1 - 11
15
2.4GHz BT / LE
mode
MAXIMUM TUNE UP TOLERANCE[dBm]
BR
13
EDR
9
LE
9
LE(2M)
9
Preliminary Specification Number : SP-9B1LV-M
40 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
5GHz WLAN
Mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11a
6/9/12/18 Mbps
(W52/W53) 36 – 64
18
(W56) 100 – 144
18
(w58) 149 - 165
18
24/36 Mbps
(W52/W53) 36 – 64
17
(W56) 100 – 144
17
(W58) 149 - 165
17
48 Mbps
(W52/W53) 36 – 64
16
(W56) 100 – 144
16
(W58) 149 – 165
16
54 Mbps
(W52/W53) 36 – 64
15
(W56) 100 – 144
15
(W58) 149 - 165
15
Mode
Rate
Channel
MAXMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11n(HT20)
MCS0 – 2
(W52/W53) 36 – 64
18
(W56) 100 - 144
18
(W58) 149 – 165
18
MCS3 – 4
(W52/W53) 36 – 64
17
(W56) 100 - 144
17
(W58) 149 – 165
17
MCS5
(W52/W53) 36 – 64
16
(W56) 100 - 144
16
(W58) 149 – 165
16
MCS6
(W52/W53) 36 – 64
15
(W56) 100 - 144
15
(W58) 149 – 165
15
MCS7
(W52/W53) 36 – 64
14
(W56) 100 - 144
14
(W58) 149 – 165
14
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE
802.11ac(VHT20)
MCS0 -2
(W52/W53) 36 – 64
18
(W56) 100 - 144
18
(W58) 149 - 165
18
MCS3 – 4
(W52/W53) 36 – 64
17
(W56) 100 - 144
17
(W58) 149 - 165
17
MCS5
(W52/W53) 36 – 64
16
(W56) 100 - 144
16
(W58) 149 - 165
16
MCS6
(W52/W53) 36 – 64
15
(W56) 100 - 144
15
(W58) 149 - 165
15
MCS7
(W52/W53) 36 – 64
14
(W56) 100 - 144
14
(W58) 149 - 165
14
MCS8
(W52/W53) 36 – 64
12
(W56) 100 - 144
12
(W58) 149 - 165
12
Preliminary Specification Number : SP-9B1LV-M
41 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Frequency of operation
Frequency of operation
Scan
Ad-hoc mode
2.4GHz
11/b/g/n(HT20)
2412 - 2462MHz
Active/Passive
Yes
W52
11a/n/ac((V)HT20)
5180 - 5240MHz
Active/Passive
Yes
W53
11a/n/ac((V)HT20)
5260 - 5320MHz
Passive
No
W56
11a/n/ac((V)HT20)
5500 - 5720MHz
Passive
No
W58
11a/n/ac((V)HT20)
5745 - 5825MHz
Active/Passive
Yes
* End users can not modify the software because F/W & driver are installed in device.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will
be on only while one of the aforementioned packets is being transmitted. In other words, this
device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
Frequency Tolerance: ± 20ppm
Preliminary Specification Number : SP-9B1LV-M
42 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
For ISED
PMN: Type1LV
HVIN: Type1LV
IC Number:772C-LBEE59B1LV
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
●The following information must be indicated on the host device of this module.
Contains IC: 772C-LBEE59B1LV
●The following statements must be described on the user manual of the host device of this module;
This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présentappareilestconformeaux CNR d’IndustrieCanada applicablesaux appareilsradio
exempts de licence. L’exploitationestautoriséeaux deuxconditions suivantes:
1) l’appareilne doitpas produirede brouillage;
2) l’utilisateurde l’appareildoitaccepter tout brouillageradioélectriquesubi, mêmesile
brouillageestsusceptible d’encompromettrele fonctionnement.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User's
manual.
●In case of the final product which can be carried around to outdoor.
The following indication is necessary to the final product.
When the AP function is used in W52;
At the time of a channel setting of W52, please indicate “for indoor use only”. During connecting, please
show the channel number which connects.
And please indicate that the end user may find out "for indoor use only channel".
When the STA function is used in channel 52, at the time of the channel 52 setting, please indicate “for
indoor use only channel”.
During connecting, please show the channel number which connects.
And please indicate that the end user may find out "for indoor use only channel".
●If the antenna of the end product is removed, please describe the follow warning on the manual of the end
product which contains this module.
This radio transmitter (IC Number: 772C-LBEE59B1LV) identify the device by certification
number or model number if Category II) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain indicated. Antenna
types not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
: 2.4GHz Monopole Gain: +0.9 dBi
: 5GHz Monopole Gain: +2.0 dBi
Le présentémetteurradio (IC Number: 772C-LBEE59B1LV) a étéapprouvépar
IndustrieCanada pour fonctionneravec les types d'antenneénumérésci-dessouset ayantun
gain admissible maximal. Les types d'antennenon inclusdanscetteliste, et dontle gain
estsupérieurau gain maximal indiqué, sontstrictementinterditspour l'exploitationde l'émetteur.
Type d’antenne
: 2.4GHz Monopole Gain: +0.9 dBi
: 5GHz Monopole Gain: +2.0 dBi
Preliminary Specification Number : SP-9B1LV-M
43 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
●If the final product use the following frequency, please note that there is a limit.
for indoor use only(5150-5250MHz bandand channel 52)
Pour usage intérieurseulement(5150-5250MHz band and channel 52)
High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350
MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to
LE-LAN devices.
Les radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer
du brouillage et/ou des dommages aux dispositifsLAN-EL..
●The following statements must be described on the user manual of the host device of this module;
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will
be on only while one of the aforementioned packets is being transmitted. In other words, this
device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
La transmission des données est toujours initiée par le logiciel, puis les données sont
transmises par l'intermédiaire du MAC, par la bande de base numérique et analogique et,
enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les seuls
moyens pour qu'une partie de la bande de base numérique active l'émetteur
RF, puis désactive celui-ci à la fin du paquet. En conséquence, l'émetteur reste uniquement
activé lors de la transmission d'un des paquets susmentionnés. En d'autres termes, ce
dispositif interrompt automatiquement toute transmission en cas d'absence d'information à
transmettre ou de défaillance.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User's
manual.
●When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm or more away
from person’s body.
Cetéquipementestconformeaux limitesd’expositionaux rayonnementsénoncéespour un
environnementnon contrôléet respecteles règlesd’expositionaux
fréquencesradioélectriques(RF) CNR-102 de l’IC. Cetéquipementdoitêtreinstalléet
utiliséengardantunedistance de 20 cm ouplus entre le radiateuret le corps humain.
●When installing it in a portable equipment.
It is necessary to take a SAR test with your set mounting this module.
Class II permissive change application is necessary using the SAR report.
Please contact Murata.
Note)
Portable equipment : Equipment for which the spaces between human body and antenna are used within
20cm.
Mobile equipment : Equipment used at position in which the spaces between human body and antenna
exceeded 20cm.
●Antenna
Please refer to the ‘Certification Antenna information’ document supplied by Murata
or please contact Murata for the detail designation of how to design the Antenna trace.
●Installation procedure
Supply Voltage
Min.
Typ.
Max.
unit
Supply
Voltage
VBAT
3.1
3.3
3.5
V
VDDIO
1.8 or 3.3
V
*VDDIO don’t influence the RF characteristic.
Preliminary Specification Number : SP-9B1LV-M
44 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
RF Power
2.4GHz WLAN
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11b
All Rate
1 - 11
19
IEEE 802.11g
6/9 Mbps
1 - 11
19
12/18/24 Mbps
1 - 11
18
36/48 Mbps
1 - 11
17
54 Mbps
1 - 11
16
IEEE 802 11n(HT20)
MCS0 - 2
1 – 11
19
MCS3
1 – 11
18
MCS4 – 5
1 – 11
17
MCS6
1 – 11
16
MCS7
1 - 11
15
*Both indoor and outdoor can be used.
2.4GHz BT / LE
mode
MAXIMUM TUNE UP TOLERANCE[dBm]
BR
13
EDR
9
LE
9
LE(2M)
9
*Both indoor and outdoor can be used.
5GHz WLAN
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11a
6/9/12/18 Mbps
(W52/W53) 36 – 64
18
(W56) 100 – 144
18
(w58) 149 - 165
18
24/36 Mbps
(W52/W53) 36 – 64
17
(W56) 100 – 144
17
(W58) 149 - 165
17
48 Mbps
(W52/W53) 36 – 64
16
(W56) 100 – 144
16
(W58) 149 – 165
16
54 Mbps
(W52/W53) 36 – 64
15
(W56) 100 – 144
15
(W58) 149 - 165
15
*At the time of indoor use.
Preliminary Specification Number : SP-9B1LV-M
45 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11a
6/9/12/18 Mbps
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
18
(W56) 100 – 144
18
(W58) 149 - 165
18
24/36 Mbps
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
17
(W56) 100 – 144
17
(W58) 149 - 165
17
48 Mbps
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
16
(W56) 100 – 144
16
(W58) 149 - 165
16
54 Mbps
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
15
(W56) 100 – 144
15
(W58) 149 - 165
15
*At the time of outdoor use.
mode
Rate
Channel
MAXMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11n(HT20)
MCS0 – 2
(W52/W53) 36 – 64
18
(W56) 100 - 144
18
(W58) 149 – 165
18
MCS3 – 4
(W52/W53) 36 – 64
17
(W56) 100 - 144
17
(W58) 149 – 165
17
MCS5
(W52/W53) 36 – 64
16
(W56) 100 - 144
16
(W58) 149 – 165
16
MCS6
(W52/W53) 36 – 64
15
(W56) 100 - 144
15
(W58) 149 – 165
15
MCS7
(W52/W53) 36 – 64
14
(W56) 100 - 144
14
(W58) 149 – 165
14
*At the time of indoor use.
Preliminary Specification Number : SP-9B1LV-M
46 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
mode
Rate
Channel
MAXMUM TUNE UP
TOLERANCE[dBm]
IEEE 802.11n(HT20)
MCS0 – 2
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
18
(W56) 100 – 144
18
(W58) 149 - 165
18
MCS3 – 4
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
17
(W56) 100 – 144
17
(W58) 149 - 165
17
MCS5
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
16
(W56) 100 – 144
16
(W58) 149 - 165
16
MCS6
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
15
(W56) 100 – 144
15
(W58) 149 - 165
15
MCS7
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
14
(W56) 100 – 144
14
(W58) 149 - 165
14
*At the time of outdoor use.
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE
802.11ac(VHT20)
MCS0 -2
(W52/W53) 36 – 64
18
(W56) 100 – 116, 132 - 144
18
(W58) 149 - 165
18
MCS3 – 4
(W52/W53) 36 – 64
17
(W56) 100 – 116, 132 - 144
17
(W58) 149 - 165
17
MCS5
(W52/W53) 36 – 64
16
(W56) 100 – 116, 132 - 144
16
(W58) 149 - 165
16
MCS6
(W52/W53) 36 – 64
15
(W56) 100 – 116, 132 - 144
15
(W58) 149 - 165
15
MCS7
(W52/W53) 36 – 64
14
(W56) 100 – 116, 132 - 144
14
(W58) 149 - 165
14
MCS8
(W52/W53) 36 – 64
12
(W56) 100 – 116, 132 - 144
12
(W58) 149 - 165
12
*At the time of indoor use.
Preliminary Specification Number : SP-9B1LV-M
47 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
mode
Rate
Channel
MAXIMUM TUNE UP
TOLERANCE[dBm]
IEEE
802.11ac(VHT20)
MCS0 – 2
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
18
(W56) 100 – 116, 132 - 144
18
(W58) 149 - 165
18
MCS3 - 4
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
17
(W56) 100 – 116, 132 - 144
17
(W58) 149 - 165
17
MCS5
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
16
(W56) 100 – 116, 132 - 144
16
(W58) 149 - 165
16
MCS6
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
15
(W56) 100 – 116, 132 - 144
15
(W58) 149 - 165
15
MCS7
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
14
(W56) 100 – 116, 132 - 144
14
(W58) 149 - 165
14
MCS8
(W52) 36 – 48
N/A
(W53) 52
N/A
(W53) 56 – 64
12
(W56) 100 – 116, 132 - 144
12
(W58) 149 - 165
12
*At the time of outdoor use.
Frequency of operation
Frequency of operation
Scan
Ad-hoc mode
2.4GHz
11/b/g/n(HT20)
2412 - 2462MHz
Active/Passive
Yes
W52
11a/n/ac((V)HT20)
5180 - 5240MHz
Active/Passive
Yes
W53
11a/n/ac((V)HT20)
5260 - 5320MHz
Passive
No
W56
11a/n/ac((V)HT20)
5500 - 5720MHz
Passive
No
W58
11a/n/ac((V)HT20)
5745 - 5825MHz
Active/Passive
Yes
* End users can not modify the software because F/W & driver are installed in device.
Compliance with IC requirement RSS-210 A9.4.4
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will
be on only while one of the aforementioned packets is being transmitted. In other words, this
device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
Conformité à la norme CNR-210 A9.4.4
La transmission des données est toujours initiée par le logiciel, puis les données sont
transmises par l'intermédiaire du MAC, par la bande de base numérique et analogique et,
enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les seuls
moyens pour qu'une partie de la bande de base numérique active l'émetteur RF, puis
désactive celui-ci à la fin du paquet. En conséquence, l'émetteur reste uniquement activé lors
de la transmission d'un des paquets susmentionnés. En d'autres termes, ce dispositif
interrompt automatiquement toute transmission en cas d'absence d'information à transmettre
ou de défaillance.
Preliminary Specification Number : SP-9B1LV-M
48 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
For Japan
Application Model Name: Type1LV
Certification Number: 001-P01338
特定無線設備の種別
Classification of
Specified Radio
Equipment
証明規則第 2条第 1項第 19 号の無線設備
2.4GHz 帯高度化省電力データ通信システム
Radio equipment for Article 2-1-19 of Certification Ordinance
証明規則第 2条第 1項第 19 号の 3の無線設備
5GHz 帯小電力データ通信システム（Ⅰ）
Radio equipment for Article 2-1-19-3 of Certification Ordinance
証明規則第 2条第 1項第 19 号の 3の2の無線設備
5GHz 帯小電力データ通信システム（Ⅱ）
Radio equipment for Article 2-1-19-3-2 of Certification Ordinance
Preliminary Specification Number : SP-9B1LV-M
49 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Annex B
Certified Antenna information
Antenna Model Name
Type1LV-Antenna
Antenna type
Monopole pattern antenna
Antenna manufacture
Murata Manufacturing Co.,Ltd.
Antenna gain
+0.9 dBi@2.4GHz
+2.0dBi@5GHz
Frequency
2400-2483.5MHz, 5150-5850MHz
Preliminary Specification Number : SP-9B1LV-M
50 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-9B1LV-M
51 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
@2442MHz
@5500MHz
■Please perform the antenna design that above certified antenna specifications of the antenna.
About the signal line between an antenna and a module
It is a 50-ohm line design.
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check "Class1 change" and "Class2 change" which the authorities define then.
The concrete contents of a check are the following three points.
1) It is the same type as the antenna type of antenna specifications.
2) An antenna gain is lower than a gain given in antenna specifications.
3) The emission level is not getting worse.
-50ohm line ( microstrip line length)
50-ohm line length
We test it at 23.8mm as a representative
Preliminary Specification Number : SP-9B1LV-M
52 / 52
Preliminary
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.