GLS85LP1004B-M-I-40CN-ED000 - Greenliant

Fact Sheet 03.001

February 2014

These specifications are subject to change without notice. 02/21/2014

GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial / Commercial Temp PATA NANDrive™

Features

 Industry Standard ATA / IDE Bus Interface

- Host Interface: 16-bit access

- Supports 48-bit address feature set

- Supports up to PIO Mode-6 1)

- Supports up to Multi-Word DMA Mode-4 2)

- Supports up to Ultra DMA Mode-6

 Performance

- Sequential data read:

Up to 60 MByte/sec

- Sequential data write:

Up to 30 MByte/sec

 Power Management

- 3.3V power supply

- Immediate disabling of unused circuitry

without host intervention

- Zero wake-up latency

 Power Specification

- Active mode

150mA typical (GLS85LP1032A)

140mA typical (GLS85LP1016B)

100mA typical (GLS85LP1008B)

60mA typical (GLS85LP1004B)

60mA typical (GLS85LP1002A)

- Sleep mode

500µA typical

 Supports SMART Commands

 Robust Built-in ECC

 Expanded Data Protection

- WP#/PD# pin configurable by firmware for

prevention of data overwrites

- Data security through user-selectable

protection zones

- Security Erase feature

 Integrated Voltage Detector

- Prevents inadvertent Write operations due to

unexpected power-down or brownout

 20-Byte Unique ID for Enhanced Security

- Factory pre-programmed 10-Byte unique ID

- User-programmable 10-Byte ID

 NAND Configuration

- 2 bits per cell (MLC)

 Temperature Range

- Commercial: 0°C to 70°C

- Industrial: -40°C to 85°C

 91-ball BGA and LBGA Package 4)

- 14mm x 24mm x 1.90mm, 1mm ball pitch, FTE

(4 GB, 8 GB, 16 GB, 32 GB)

- 14mm x 24mm x 1.45mm, 1mm ball pitch, LFTE

(4 GB, 8 GB) Note: Devices using LFTE are not

recommended for new designs.

- 12mm x 24mm x 1.40mm, 1mm ball pitch, LBTE

(2 GB)

 All Devices are RoHS Compliant

Product Description

The GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial and Commercial Temp PATA NANDrive™

devices (referred to as “PATA NANDrive” in this fact

sheet) are high-performance, fully integrated solid state

drives. They combine a Greenliant NAND controller and 2,

4, 8, 16 or 32 GByte of NAND flash memory in a multi-

chip package. These products are ideal for embedded

and portable applications that require smaller form factor

and more reliable data storage.

ATA-based solid state mass storage technology is widely

used in GPS and telematics, in-vehicle infotainment,

portable and industrial computers, handheld data

collection scanners, point-of-sale terminals, networking

and telecommunications equipment, robotics, audio and

video recorders, monitoring devices and set-top boxes.

PATA NANDrive supports standard ATA/IDE protocol with

up to PIO Mode-61), Multi-Word DMA Mode-42) and Ultra

DMA Mode-6 interface. PATA NANDrive provides

complete IDE hard disk drive functionality and

compatibility in a 14mm x 24mm BGA package or a

12mm x 24mm LBGA package for easy, space saving

mounting to a system motherboard. These products

surpass traditional storage in their small size, security,

reliability, ruggedness and low power consumption.

The integrated NAND flash controller with built-in

advanced NAND management firmware communicates

with the host through the standard ATA protocol. It does

not require any additional or proprietary software such as

the Flash File System (FFS) and Memory Technology

Driver (MTD).

PATA NANDrive provides a WP#/PD# pin to protect

critical information stored in the flash media from

unauthorized overwrites. PATA NANDrive is pre-

programmed with a 10-Byte unique serial ID and has the

option of programming an additional 10-Byte serial ID for

even greater system security.

PATA NANDrive’s advanced NAND management

technology enhances data security, improves endurance

and accurately predicts the remaining life of the NAND

flash devices. This innovative technology combines robust

error correction capabilities with advanced wear-leveling

algorithms and bad block management to significantly

extend the life of the product.

1) PATA NANDrive is capable of supporting PIO Mode-6, but

Identify-Drive information report will show PIO Mode-4

2) PATA NANDrive is capable of supporting Multi-Word DMA

Mode-4, but Identify-Drive information report will show

MWDMA Mode-2

Fact Sheet 03.001

February 2014

These specifications are subject to change without notice. 02/21/2014

GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial / Commercial Temp PATA NANDrive™

1.0 GENERAL DESCRIPTION

Each PATA NANDrive contains an integrated PATA NAND flash memory controller and NAND flash die in a BGA

or LBGA package. Refer to Figure 2-1 for the PATA NANDrive block diagram.

1.1 Optimized PATA NANDrive

The heart of PATA NANDrive is the PATA NAND flash

memory controller, which translates standard PATA

signals into flash media data and control signals. The

following components contribute to PATA NANDrive’s

operation.

1.1.1 Microcontroller Unit (MCU)

The MCU transfers the ATA/IDE commands into data

and control signals required for flash media operation.

1.1.2 Internal Direct Memory Access (DMA)

PATA NANDrive uses internal DMA allowing instant

data transfer from/to buffer to/from flash media. This

implementation eliminates microcontroller overhead

associated with the traditional, firmware-based

approach, thereby increasing the data transfer rate.

1.1.3 Power Management Unit (PMU)

The PMU controls the power consumption of PATA

NANDrive. The PMU dramatically reduces the power

consumption of PATA NANDrive by putting the part of

the circuitry that is not in operation into sleep mode.

The Flash File System handles inadvertent power

interrupts and has auto-recovery capability to ensure

PATA NANDrive’s data integrity. For regular power

management, the host must send an

IDLE_IMMEDIATE command and wait for command

ready before powering down PATA NANDrive.

1.1.4 Embedded Flash File System

The embedded flash file system is an integral part of

PATA NANDrive. It contains MCU firmware that

performs the following tasks:

1. Translates host side signals into flash media

writes and reads

2. Provides flash media wear leveling to spread

the flash writes across all memory address

space to increase the longevity of flash media

3. Keeps track of data file structures

4. Manages system security for the selected

protection zones

5. Stores the data in flash media upon completion

of a Write command (PATA NANDrive does not

perform Post-Write operations, except for when

the write cache is enabled)

1.1.5 Error Correction Code (ECC)

High performance is achieved through optimized

hardware error detection and correction.

1.1.6 Serial Communication Interface (SCI)

The Serial Communication Interface (SCI) is designed

for error reporting. During the product development

stage, it is recommended to provide the SCI port on

the PCB to aid in design validation.

1.1.7 Multi-tasking Interface

The multi-tasking interface enables fast, sustained

write performance by allowing concurrent Read,

Program and Erase operations to multiple flash media.

1.2 SMT Reflow Consideration

The PATA NANDrive family utilizes standard NAND

flash for data storage. Because the high temperature

in a surface-mount soldering reflow process can alter

the content on NAND flash, do not program PATA

NANDrive before the reflow process.

1.3 Advanced NAND Management

PATA NANDrive’s integrated controller uses

advanced wear-leveling algorithms to substantially

increase the longevity of NAND flash media. Wear

caused by data writes is evenly distributed in all or

select blocks in the device that prevents “hot spots” in

locations that are programmed and erased extensively.

This effective wear-leveling technique results in

optimized device endurance, enhanced data retention

and higher reliability required by long-life applications.

Fact Sheet 03.001

February 2014

These specifications are subject to change without notice. 02/21/2014

GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial / Commercial Temp PATA NANDrive™

2.0 FUNCTIONAL BLOCKS

Figure 2-1: PATA NANDrive Block Diagram

Fact Sheet 03.001

February 2014

These specifications are subject to change without notice. 02/21/2014

GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial / Commercial Temp PATA NANDrive™

3.0 PRODUCT ORDERING INFORMATION

GLS 85 LP 1 0xxB - M - C - LFTE - NDxxx

XX XX X XXXX - X - X - XXXX - XXXXX

Ordering Code 3)

NDxxx = NANDrive Revision

EDxxx = Evaluation Board Revision

Environmental Attribute

E = non-Pb solder (RoHS Compliant)

Package Modifier

T = 88 ball positions (nearest letter code

to total ball count of 91)

Package Type

F = BGA (max. package height 1.90mm)

LF = LBGA (max. package height 1.45mm)

LB = LBGA (max. package height 1.40mm)

Operation Temperature

I = Industrial: -40°C to +85°C

C = Commercial: 0°C to +70°C

NAND configuration

M = 2 bits per cell

Generation / Product Configuration

A = First generation

B = Second generation

Capacity

002 = 2 GByte

004 = 4 GByte 4)

008 = 8 GByte 4)

016 = 16 GByte

032 = 32 GByte

MByte or GByte Designator

0 = MByte, 1 = GByte

Interface

P= Parallel ATA/IDE Interface

Voltage

L = 3.3V

Product Series

85 = NANDrive

3) For legacy NANDrive products, no ordering code is required. Note that the top side marking on the package typically does

not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC (custom specification) which is required by the end-

customer to be marked on the device.

4) GLS85LP1008B and GLS85LP1004B currently have two packages available; FTE and LFTE. Devices using LFTE are not

recommended for new designs.

Fact Sheet 03.001

February 2014

These specifications are subject to change without notice. 02/21/2014

GLS85LP1002A / 1004B / 1008B / 1016B / 1032A

Industrial / Commercial Temp PATA NANDrive™

Valid Combinations

Valid product combinations are those that are in the mass production or will be in the mass production. Consult

your Greenliant sales representative to confirm availability of the valid combinations and to determine availability

of new product combinations.

Table 3-1: PATA NANDrive Product Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Package

2GB

Commercial (0°C to 70°C)

GLS85LP1002A-M-C-LBTE

LBTE, 12x24x1.40mm

GLS85LP1002A-M-C-LBTE-ND000

LBTE, 12x24x1.40mm

Industrial (-40°C to 85°C)

GLS85LP1002A-M-I-LBTE-ND000

LBTE, 12x24x1.40mm

4GB

Commercial (0°C to 70°C)

GLS85LP1004B-M-C-LFTE

LFTE, 14x24x1.45mm

GLS85LP1004B-M-C-FTE-ND0004)

FTE, 14x24x1.90mm4)

Industrial (-40°C to 85°C)

GLS85LP1004B-M-I-FTE-ND0004)

FTE, 14x24x1.90mm4)

8GB

Commercial (0°C to 70°C)

GLS85LP1008B-M-C-LFTE4)

LFTE, 14x24x1.45mm4)

GLS85LP1008B-M-C-FTE-ND0004)

FTE, 14x24x1.90mm4)

Industrial (-40°C to 85°C)

GLS85LP1008B-M-I-FTE-ND0004)

FTE, 14x24x1.90mm4)

16GB

Commercial (0°C to 70°C)

GLS85LP1016B-M-C-FTE

FTE, 14x24x1.90mm

GLS85LP1016B-M-C-FTE-ND000

FTE, 14x24x1.90mm

Industrial (-40°C to 85°C)

GLS85LP1016B-M-I-FTE-ND000

FTE, 14x24x1.90mm

32GB

Commercial (0°C to 70°C)

GLS85LP1032A-M-C-FTE

FTE, 14x24x1.90mm

GLS85LP1032A-M-C-FTE-ND000

FTE, 14x24x1.90mm

Industrial (-40°C to 85°C)

GLS85LP1032A-M-I-FTE-ND000

FTE, 14x24x1.90mm

4) GLS85LP1008B and GLS85LP1004B currently have two packages available; FTE and LFTE. Devices using LFTE are not

recommended for new designs.

Table 3-2: PATA NANDrive Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Commercial (0°C to 70°C)

GLS85LP1002A-M-C-40CN-K