AIM & THURLBY THANDAR INSTRUMENTS TG5011 & TG2511 Advanced Function/Arbitrary/Pulse Generators Up to 50MHz sine and square, 14 digits or 1Hz resolution Arbitrary waveforms of up to 128K points at up to 125MS/s True pulse generator with variable delay and variable rise/fall Internal & external digital modulation, AM, FM, PM, PWM, FSK Programmable via USB, GPIB and LXI compliant LAN interfaces aimtti.com aimtti.co.uk | aimtti.us Features at a glance TG5011 & TG2511 TGxx11 Series Function/Arbitrary/Pulse generators Click each icon for a detailed explanation The TGxx11 Series represents the state-of-the-art in DDS based function generators. The 50MHz TG5011 significantly outperforms other generators in its price range, not just because of its frequency range, but because of its all round performance and features. The TG2511 incorporates a similar feature set at a still lower cost and represents exceptional value for those with lower frequency requirements. TTi manufactures a wide range of function, arbitrary and pulse generators from lower frequency analog units to multi-channel variable clock arbitrary generators. Measurably better value Features in detail Standard, Pulse and Arbitrary Waveforms Higher Waveform Frequencies Independently variable Rise and Fall The TG5011 out-performs other generators in its price range by offering both sine and square waves up to 50MHz. The lower cost TG2511 operates to 25MHz. The generators offer very fast edge speeds of better than 8ns on the TG5011 or 13ns on the TG2511, but the edges can be slowed down to simulate slower pulses. Rise and fall times are independently variable in the range 5ns to 40us (10ns to 40us on the TG2511), or can be linked so that both edge speeds are the same. Trigger, Burst and Gate Exceptional frequency precision The frequency of these waveforms can be set with up to 14 digits or one micro hertz of resolution. The DDS based frequency generation system uses a TCXO timebase oscillator with a stability of 1ppm. Waveform Quality The TG5011 and TG2511 generate high purity sine waves with low harmonic distortion and low phase noise. Square waves have a rise time of below 8ns (13ns on TG2511) and low overshoot. Variable symmetry can be used up to 25MHz. Triangle and Ramp High quality triangle and variable symmetry ramp waveforms are available up to 500kHz (TG5011) or 250kHz (TG2511). These waveforms are also available at higher frequencies via the arbitrary function but without symmetry adjustment and with reduced waveform quality as the frequency increases. As with all other waveforms, pulses can be triggered from an external trigger input (or manual trigger, the internal trigger generator or a Bus command). Burst mode creates a burst of between one and a million pulses in response to each active edge of the trigger. Gated cause pulses to be generated only when the gate signal is true. The gate source can be external or internal exactly as the trigger signal. Arbitrary Waveforms Both generators offer DDS generated arbitrary waveforms capability. A number of standard waveforms are included, and up to four user defined arbitrary waveforms can be stored in the instrument at any one time. 14 bits, 128k words, 125MS/s Waveforms have a vertical resolution of 14 bits (16,384 amplitude levels). Waveforms can be created using between 2 and 131,072 points (128k). The sampling rate is 125MHz and DDS techniques are used to provide any repetition rate between 1uHz and 10MHz (TG5011) or 6MHz (TG2511) with up to 14 digits of frequency resolution. VLF generation The high resolution of the DDS system means that very low frequencies can be set. For example, a frequency of around 1mHz could be set with a resolution of 0.1% and a stability of 1ppm. Full Pulse Generator capabilities Both models incorporate a pulse generator mode which provides wide range pulse width and delay independent of period. Rise and fall times (edge speeds) are also fully variable. Wide-range repetition rate On the TG5011, the pulse period can be set between 80ns and 2000 secs. (0.5mHz to 12.5MHz) with a resolution of 14 digits or 1Hz. On the TG2511, the minimum pulse period is 160ns (6.25MHz). Internal and External Waveform Storage Up to four user defined waveforms totalling up to 256k words can be stored within the permanent internal memory of the instrument. However, a front mounted USB port enables external Flash memory storage of up to 1000 waveforms of any size. This memory stick also provides a quick and convenient method for transferring waveform files to and from a PC. It can also be used for storing instrument set-ups. Pre-built Complex Waveforms Commonly used complex waveforms are provided both built-in to the instrument and for loading into the user defined waveform space. These include sin(x)/x, exponential rise and fall, logarithmic rise and fall, gaussian, lorentz, haversine and cardiac waveforms. Waveform Creation & Editing Fully variable pulse Width and Delay Pulse width and pulse delay can be independently set to a resolution of 10ns. Minimum pulse width is 20ns and duty cycles can be as low as one in two billion. Note that display screens on this page are shown at around 80% of actual size. Arbitrary waveforms can be created and edited using the simple tools built into the instrument. However, complex waveforms require an external PC based editor. Both instruments are supplied with Waveform Manager Plus for Windows(R) which provides the most comprehensive set of waveform tools available including a mathematical expression editor, freehand drawing, waveform libraries, and import of waveforms using the Clip Board. More information is provided on Page 5 of this brochure. Features in detail Storage, Modulations, Sweep & Burst, Noise USB Flash Drive Interface Sweep and Burst Both instruments incorporate a front mounted USB socket for connection of flash memory disk drives which can store up to 1,000 waveforms and 1,000 setups. Sweep, Burst and Gated modes of operation are available using either an external trigger signal or the internal trigger generator. Unlimited Waveform Storage These drives can be used both to store waveforms permanently and to transfer waveforms from or to a PC. Arbitrary waveform storage within the instrument is limited to four waveforms. Each flash drive can store up to 1000 waveforms which can be accessed using the instruments file handling utilities. Wide range Frequency Sweep Phase continuous sweep is available for all standard and arbitrary waveforms except for pulse. The sweep range is from 1Hz through to the maximum for the chosen carrier waveform. Start and stop frequencies can be set independently. The sweep can be linear or logarithmic, triggered or continuous with a period between 1ms and 500s. The sweep trigger can be manual or internal from the trigger generator or external from the trigger socket or from a remote interface command. A marker is provided that outputs an edge synchronous with any frequency point within the sweep. Storage of Instrument Set-ups Up to nine complete set-ups of the instrument can be stored within its own non-volatile memory. Up to 1000 further set-ups can be stored on each flash drive. Digital Modulation, Internal & External Both generators offer a comprehensive set of digitally based modulations. The internal modulation source can use any of the standard or arbitrary waveforms currently within the generator (including noise) thus removing the need for an external modulation source. A modulating frequency between 1Hz and 20kHz can be specified. An external modulation input enables any external waveform source to be used when required. The external bandwidth is DC to 20kHz. AM, FM and PM Sine, square, ramp or arbitrary waveforms can be modulated using amplitude, frequency or phase modulation. Amplitude depth is variable from 0.0% to 120.0%, frequency deviation from zero to Fmax/2, and phase deviation from -360.0 to +360.0 degrees. Triggered Burst In Burst mode, each active edge of the trigger will produce one burst of the waveform. The number of cycles in a burst can be set between 1 and 1,048,575 (or infinite). The burst starts and ends at a waveform phase angle settable between -360.0 to +360.0 degrees. Trigger signal The trigger signal can be manual from the front panel key, internal from the internal trigger generator, external from the trigger-in socket, or remote via a bus command. The trigger-in socket has a nominal TTL threshold and can be set to +ve edge or -ve edge triggering. The minimum trigger pulse width is 50ns. The internal trigger generator is variable between 2mHz and 1MHz with 9 digit resolution. Gated In Gated mode the waveform runs only when the gate signal is true. The start point of the waveform is settable from -360.0 to +360.0 degrees and a the last cycle is completed after the gate signal goes false. All of the options available for triggering are available for gating. The trigger-in socket can be set as high or low for true. Noise Generation PWM Pulse width modulation is available for the pulse function using any standard or arbitrary waveform including noise. Pulse width deviation is variable between 0% and 100%. FSK Frequency shift keying between any two frequencies is available for sine, square, ramp or arbitrary waveforms using the internal trigger generator or an external trigger signal. The internal trigger generator is variable between 2mHz and 1MHz with nine digit resolution. Both models can generate gaussian white noise to a -3dB bandwidth of 20MHz. The noise generation algorithm achieves a high crest factor (peak to rms ratio) of 5.27. Adding Noise to a waveform Noise can be added to any waveform except pulse. The amount of noise added can be specified as 0% to 50% of the amplitude of the carrier waveform. Modulating with Noise Noise can be used as the modulating waveform for AM, FM, PM or PWM modulations using any of the carrier waveforms allowable for that modulation type. Features in detail Phase Locking, Interfaces, Outputs/Inputs, Wave Edit Locking to Other Sources Both the models include external reference and phase locking as standard, unlike some competitor products for which they are an expensive option. External Frequency Reference The generators use a high quality TCXO crystal as the internal frequency reference providing 1ppm accuracy and stability. If a higher accuracy or stability is required, an external 10MHz reference signal (from an off-air standard for example) can be applied to the Ref. Clock input. Phase Locking Two Generators (or more) Two generators can be synchronised together to provide outputs at the same frequency (or at harmonics) and with a phase difference. The amplitude and phase of these outputs can also be modulated providing the capability to perform QAM and QPSK respectively. Any waveform other than pulse can be used, and the phase difference is adjustable between -360.0 and +360.0 to a resolution of 0.1 degrees. Skew is better than 5ns. It is also possible to synchronise more than two generators but the resulting precision is not specified. Full Remote Control All functions of the generators can be controlled from the digital interfaces. Arbitrary waveform data can also be loaded using these interfaces. An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows* and HP-VEE*. The LAN interface uses a standard 10/100 base-T Ethernet hardware connection with ICMP and TCP/IP Protocol for connection to a Local Area Network or direct connection to a single PC. This interface supports LXI and is the most appropriate for larger system use because of its scalable nature. High Waveform Quality The high waveform quality with its low aberrations is available over a wide amplitude range of 20mV to 20V pk-pk emf (10mV to 10V into 50 W). DC offset is provided independently of waveform attenuation so, for example, a waveform amplitude of millivolts can be combined with a dc level of volts. Intelligent Amplitude Display Amplitudes can be displayed as peak to peak or as RMS values, with the rms being correctly calculated for the waveform shape. RMS values can alternatively be specified in dBm. If preferred values can be entered in terms of high level and low level instead of amplitude and offset. The amplitudes are shown relative to the selected load impedance which is 50 W (or High-Z) by default, but can be selected as any impedance between 1 W and 10 kW. Multi-function Sync Output The Sync output provides a logic level signal that can perform a number of functions intended for synchronisation with external equipment: Normal Waveform Sync Modulation Sync Burst Sync Sweep Sync (with sweep marker) Trigger Signal Out Phase Lock (for 2nd generator) The signal type can be selected manually or automatically dependent upon the function in use. Rear Panel Inputs and Outputs In addition to the digital bus interfaces, the rear panel carries four I/O sockets: External Modulation Input - for AM, FM, PM and PWM external modulation. Trigger Input - for external triggering of Burst, Gated or Sweep waveforms. Reference Clock Input - for use with an external frequency reference or phase locking of two generators. Reference Clock Output - a buffered version of whichever clock (internal or external) that the generator is using. Waveform Manager Plus The LAN interface is compliant with LXI (LAN eXtenWaveform Manager Plus is a Windows* based sions for Instrumentation) class C. application for creation, editing and management of LXI is the next-generation, LAN-based modular arbitrary waveforms using a PC architecture standard for automated test systems It incorporates a complete suite of tools for waveform managed by the LXI Consortium, and is expected to become the successor creation and editing including standard waveforms, mathematical to GPIB in many systems. expressions and freehand drawing. Virtually any waveform can be created USB provides a simple and convenient means of using combinations of these tools. connection to a PC and is particularly appropriate for Mathematical Expression Editor small system use. USB has effectively replaced The sophisticated mathematical expression editor allows geometric, RS232 in many applications. logarithmic and pulse functions to be combined to create exact The interface uses a standard USB 2.0 hardware connection and is representations of complex signals. implemented as virtual-COM port. A Windows* USB driver is provided. Different expressions can be used for different sections of a waveform As well as the rear mounted USB device interface connector, a front and can be combined with imported waveforms or drawn waveforms mounted USB Host interface connector allows USB Flash memory to be where mathematical representation is not possible. connected. G versions of the products are fitted with a GPIB (IEEE-488) interface. They retain both the other interfaces, giving them even greater flexibility. * LabView and LabWindows are trademarks of National Instruments. HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 2000, XP, Vista and Windows 7. Windows is a trademark of Microsoft Inc. Import of Other Waveforms The program offers direct import from .csv files, the most commonly used format for graphical description. Additionally a Clipboard import function supports any waveform that can be described by a set of Y-axis data points regardless of their format. Any instrument or waveform generating program that can create a list of Y values can therefore be accommodated. This is a highly flexible method which can be used to create arbitrary generator waveforms from signals captured by instruments such as oscilloscopes and network analysers, or from software such as MathCad. Features in detail High Resolution LCD The 3.6" diagonal panel uses 256 x 112 pixels and provides a large amount of simultaneous information. System connection information is shown on the top line. Below that is a general status screen showing five major parameters. These parameters change depending upon the function being used. Below the status information is the main editing line which shows the parameter currently under control. Representative Waveform Display Display, Control, Bench/Rack Mounting Bench-top Operation The generators are highly compact and use a minimum of bench space. Protective mouldings guard against knock damage and a multi-position stand angles the instrument conveniently as well as providing a carry handle. Rack Mounting For system applications the generators can be rack mounted. The area the to right of the status section shows a representation of the With the protective mouldings and handle removed the size is half rack current waveform. width by 2U high. This is more than just a fixed display for each waveform, it is calculated from the waveform parameters and gives a live indication when values such as symmetry, rise time or pulse width are changed. Even user defined arbitrary waveforms are shown (subject to the limitations of the display resolution). Modulation waveforms and representations of the modulated carrier are shown simultaneously. Burst count waveforms are also shown graphically. A 2U rack mounting kit is available suitable for one or two instruments. Soft Key Control Six soft keys below the display provide access and control of the parameters for each function. All numeric parameters can be set directly from the numeric keypad, or can be changed using the spin wheel. Period entry can be chosen instead of frequency, and amplitude and offset can be changed to Hi and Lo levels. Frequencies can be entered in any units from uHz to MHz, periods from ns to seconds, and amplitudes in mV or V, rms or pk-pk, or in dBm The currently selected waveform and major functions are also indicated by illumination of the respective keys. Mechanical Drawings Rear panel mounts the digital interfaces and the rear I/O connectors. (Note: GPIB interface is only fitted to suffix G models) TG5011 & TG2511 - Technical Specifications STANDARD WAVEFORMS SINE Note that purity specifications above 25MHz apply only to the TG5011. Frequency Range: 1Hz to 50MHz (TG2511 - 1Hz to 25MHz) Frequency Resolution: 1Hz, 14 digits Output Level: 10mVp-p to 10Vp-p into 50 W Amplitude Flatness Relative to 1kHz: <100kHz 0.1dB, <5MHz 0.15dB, <25MHz 0.3dB, <50MHz 0.5dB Harmonic Distortion: <1 Vp-p > 1Vp-p DC to 20kHz -65dBc -65dBc 20kHz to 100kHz -60dBc -60dBc 100kHz to 1MHz -45dBc -45dBc 1MHz to 25MHz -40dBc -35dBc 25MHz to 50MHz -40dBc -28dBc Non-Harmonic Spurii: <-60dBc to 1MHz, <-60dBc + 6dB/octave 1MHz to 50MHz Phase Noise: -115dBc/Hz, typical (10kHz offset) SQUARE Frequency Range: Resolution: Output Level: Rise and Fall Times: Overshoot: Variable Duty Cycle: Asymmetry: Jitter (RMS): 1Hz to 50MHz (TG2511 - 1Hz to 25MHz) 1Hz, 14 digits 10mVp-p to 10Vp-p into 50 W <8ns (TG2511 - <13ns) <5% 20% to 80% to 10MHz, 0.1% resolution, 40% to 60% to 25 MHz, 0.1% resolution, 50% (fixed) above 25MHz 1% of period + 5ns (@ 50% duty) 0.5ns + 100 ppm of period RAMP & TRIANGLE Frequency Range: Resolution: Output Level: Linearity Error: Variable Symmetry: 1Hz to 500kHz (TG2511 - 1Hz to 250kHz) 1Hz, 12 digits 10mVp-p to 10Vp-p into 50 W <0.1% to 30 kHz 0.0 % to 100.0 %, 0.1% resolution. Single key operation of 50% (Triangle) Note the triangle and sawtooth waveforms are also available from the arbitrary waveform menu enabling repetition rates of up to 10MHz/6MHz. Waveform quality will deteriorate at higher frequencies however. PULSE Frequency Range: Resolution: Output Level: Overshoot: Jitter: Rise/Fall Times: Edge Range: Edge Resolution: Width Range: Width Resolution: Delay Range: Delay Resolution: 500 Hz to 12.5MHz (TG2511 - 500 Hz to 6.25MHz) 1Hz , 14 digits 10mVp-p to 10Vp-p into 50 W <5% 300ps + 0.01% of period Rise and Fall times can be independently varied or can be varied together simultaneously. <8ns to 40s (TG2511 - <13ns to 40s) 0.1ns for rise/fall time 100ns; 1ns for rise/fall >100ns and 2s; 10ns for rise/fall >2s and 40s 20ns to 2000s (20ns minimum for period 40s; 200 ns minimum for period >40s and 400s; 2s minimum for period >400s) 10ns for period 40s; 100ns for period >40s and 400s; 1s for period >400s 0ns to 2000s 10ns for period 40s; 100ns for period >40s and 400s; 1s for period >400s ARBITRARY WAVEFORMS In-built Arbitrary Waveforms Sinc, Exponential Rise, Logarithmic Rise, DC, Positive and Negative Ramps and Square waveforms are built-in and always present. Additional waveforms are supplied on disc (Cardiac, Gaussian, Exponential Fall, Logarithmic Fall). User defined Arbitrary Waveforms Up to 4 additional or user defined waveforms may be stored in non-volatile memory. Waveforms can be defined by downloading of waveform data via USB memory stick, remote interfaces, or editing via the instrument's front panel. Waveform Size: 2 points to 131072 points (128k). Memory Size: Up to 4 waveforms of up to 64k points, or 2 waveforms of up to 128k points, (or 2 of 64k points plus 1 of 128k points). External Storage: Up to 1,000 waveforms per USB memory stick. Vertical Resolution: 14 bits Frequency Range: 1Hz to 10MHz (TG2511 - 1Hz to 6MHz) Resolution: 1Hz , 14 digits Output Level: 10mVp-p to 10Vpp into 50 W Sampling rate: 125MS/s Output Filter: Selects between 50MHz Elliptic or 20MHz Bessel filter depending on the waveform. Arbitrary Waveform Creation and Editing Waveform creation and editing is provided within the generator including point insertion, line drawing and interpolation. WAVEFORM MANAGER PLUS Both generators are supplied with Waveform Manager Plus. This Windows* based software provides a sophisticated tool set for the creation, editing and management of arbitrary waveforms. The waveforms can be transferred to the generator either using a USB memory stick, or by the digital interfaces. NOISE Gaussian White Noise can be added to any carrier waveform except pulse, square and noise itself. Note however that noise can be added to the square wave available in the arbitrary menu. The amount of noise added can be specified as 0% to 50% of the amplitude of the carrier waveform. Noise can also be used as modulating waveform. Bandwidth (-3dB): 20MHz typical. Crest Factor: 5.27 (Vp/Vrms) Output Level: 10mVp-p to 10Vpp into 50 W INTERNAL FREQUENCY REFERENCE Ageing Rate: Temp. Stability: 1ppm first year <1ppm over the specified temperature range MODULATION AM Carrier Waveforms: Sine, Square, Ramp, Arb Modulation Source: Internal/External Internal Modulating Waveforms: Sine, Square, Up Ramp, Down Ramp, Triangle, Noise, DC, Sinc, Exponential Rise, Logarithmic Rise and User Defined Arbs Internal Modulating Frequency: 1Hz to 20kHz, 1Hz resolution Amplitude Depth: 0.0% to 120.0%, 0.1% resolution FM Carrier Waveforms: Sine, Square, Ramp, Arb Modulation Source: Internal/External Internal Modulating Waveforms: Sine, Square, Up Ramp, Down Ramp, Triangle, Noise, DC, Sinc, Exponential Rise, Logarithmic Rise and User Defined Arbs Internal Modulating Frequency: 1Hz to 20kHz, 1Hz resolution Frequency Deviation: DC to Fmax/2, 1Hz resolution PM Carrier Waveforms: Sine, Square, Ramp, Arb Modulation Source: Internal/External Internal Modulating Waveforms: Sine, Square, Up Ramp, Down Ramp, Triangle, Noise, DC, Sinc, Exponential Rise, Logarithmic Rise and User Defined Arbs Internal Modulating Frequency: 1Hz to 20kHz, 1Hz resolution Phase Deviation: -360.0 to +360.0 degrees, 0.1 degree resolution PWM Carrier Waveforms: Pulse Modulation Source: Internal/External Internal Modulating Waveforms: Sine, Square, Up Ramp, Down Ramp, Triangle, Noise, DC, Sinc, Exponential Rise, Logarithmic Rise and User Defined Arbs Internal Modulating Frequency: 1Hz to 20kHz, 1Hz resolution Width Deviation: 0% to 100% of pulse width, resolution same as of pulse width FSK Carrier Waveforms: Sine, Square, Ramp, Arb Source: Internal/External (via TRIG IN) Internal Modulation: 50% duty cycle square (2mHz to 100kHz) Triggered Burst Each active edge of the trigger signal will produce one burst of the waveform. Carrier Waveforms: Sine, Square, Ramp, Arb, Pulse Maximum Carrier Frequency: 10MHz (finite cycles), 50MHz (infinite), subject to carrier waveform. Number of Cycles: 1 to 1,048,575 and infinite. Trigger Rep. Rate: 2mHz to 1MHz internal dc to 1MHz external. Trigger Source: Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Start/Stop Phase: -360.0 to +360.0 degrees, 0.1 degree resolution. Gated Waveform will run while the Gate signal is true and stop while false. Carrier Waveforms: Sine, Square, Ramp, Arb, Pulse, Noise Maximum Carrier Frequency: 10 MHz, subject to carrier waveform Trigger Rep. Rate: 2mHz to 1MHz internal, dc to 1MHz external. Gate Signal Source: Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Start/Stop Phase: -360.0 to +360.0 degrees, 0.1 degree resolution. Sweep Frequency sweep capability is provided for both standard and arbitrary waveforms. Carrier Waveforms: All standard and arbitrary except pulse. Sweep Mode: Linear or logarithmic, triggered or continuous. Sweep Direction: Up, down, up/down or down/up. Sweep Range: From 1Hz to 50MHz, subject to carrier waveform. Phase continuous. Independent setting of the start and stop frequency. Sweep Time: 1ms to 500s (6 digit resolution). Marker: Variable during sweep. Trigger Source: The sweep may be free run or triggered from the following sources: Internal from keyboard or trigger generator. Externally from TRIG IN input or remote interface. TG5011 & TG2511 - Technical Specifications (continued) Trigger Generator Internal source 2mHz to 1MHz square wave adjustable in 1s steps, 9 digit resolution. Also available for external use from the SYNC OUT socket. OUTPUTS Main Output 50 W 20mV to 20Vp-p open circuit (10mV to 10Vp-p into 50 W). Amplitude can be specified open circuit (Hi Z) or into an assumed load of 50W or a specified impedance between 1 W and 10k W in Vpk-pk, Vrms or dBm. Amplitude Accuracy: 2% 1mV at 1kHz into 50 W. DC Offset Range: 10V. DC offset plus signal peak limited to 10V from 50 W. DC Offset Accuracy: Typically 3% 10mV. Resolution: 3 digits or 1mV for both Amplitude and DC Offset. Output Impedance: Amplitude: Sync Out Multifunction output user definable or automatically selected to be any of the following: Carrier Waveform Sync: The function varies with waveform type as follows: Sine/Ramp/Pulse - A square wave with 50% duty cycle at the waveform frequency. Square - A square wave with same duty cycle as the main output at the waveform frequency. Arbs - A square wave with 50% duty cycle at the waveform frequency. The sync is a TTL high when the first point of the waveform is output. Noise - No sync associated with noise. Modulation Sync: The function varies with modulation type as follows: AM/FM/PM/PWM - A square wave with 50% duty cycle referenced to the internal modulation waveform when modulation source is internal, or a square wave referenced to the carrier waveform when modulation source is external. No sync is associated with noise as the modulation source. FSK - A square wave referenced to the trigger rate. The sync is a TTL high when hop frequency is the output frequency and TTL low when carrier frequency is the output frequency for positive slope and vice versa for negative slope. Burst Sync: A square wave that is a TTL high when the burst begins and a TTL low when burst is completed. Trigger: Selects the current trigger signal. Useful for synchronizing burst or gated signals. Sweep Sync: The function varies with marker selection as follows: Marker Off - A square wave that is a TTL low from the midpoint of the sweep and a TTL high from the end of the sweep. Marker On - A square wave that is a TTL low from the marker frequency and a TTL high from the end of the sweep. Output Signal Level: Logic level nominally 3V. Ref Clock Output Buffered version of the 10MHz clock currently in use (internal or external) Output Level: Nominally 3V logic level from 50 W. BUS INTERFACES Full digital remote control facilities are available through LAN and USB and optional GPIB interfaces. LAN Interface: Ethernet 100/10base - T hardware connection. LXI Compliance: LXI V1.2, Class C compliant. USB Interface: Standard USB 2.0 hardware connection. Implemented as virtual-COM port. GPIB Interface: Conforming with IEEE-488.2 (option G only) USB Flash Drive: Front mounted socket for waveform and setup storage/recall. Driver Software Supplied IVI Driver: LV/CVI Driver: USB Driver: * LabView and LabWindows are trademarks of National Instruments. HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 2000, XP, Vista and Windows 7. Windows is a trademark of Microsoft. GENERAL SPECIFICATIONS Display and Data Entry Display: Type: Data Entry: Stored Settings: Black on white backlit graphics display - pixel format: 256 x 112 Keyboard selection of mode, waveform etc.; value entry direct by numeric keys or by rotary control. Up to 9 complete instrument set-ups may be stored and recalled from non-volatile memory. Up to 1000 set-ups can be stored per USB stick. AC Supply AC Input: 110-240VAC 10% 50/60Hz; 100-120VAC 10% 400Hz; 60VA max. Installation Category II. Temperature & Environmental Operating Range: Storage Range: Environmental: +5C to +40C, 20% to 80% RH -20C to + 60C Indoor use at altitudes up to 2000m, Pollution Degree 2. Safety & EMC Safety: EMC: Complies with EN61010-1 Complies with EN61326 Physical Size: INPUTS Weight: Trig In An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc. Full installation for CVI and LabVIEW instrument drivers. An installation file is supplied calling a standard Windows* USB driver. Bench top use: height 97mm (2.62"); width 250mm (9.84"); length 270mm (10.63"). Rack mounted use: height 86.5mm (3.4"); width 213.5mm (8.4"); length 244mm (9.61"); i.e. 1/2-rack x 2U. 2.55 kg (5.6 lbs) OPTIONS Frequency Range: DC - 1MHz. Signal Range: Threshold nominally TTL level; maximum input 10V. Minimum Pulse Width: 50ns Polarity: Selectable as high/rising edge or low/falling edge. Input Impedance: 10k W Rack Mount (RM200A) External Modulation Input (for AM, FM, PM, PWM) Option G adds a GPIB (IEEE-488) interface. This is a factory-fit option only. Voltage Range: Input Impedance: Bandwidth: 5V full scale 5k W typical DC to 20kHz Ref Clock Input Input for an external 10MHz reference clock Voltage Range: 1Vpp - 5Vpp Maximum Voltage: +5V Minimum Voltage: -1V PHASE SYNC (Phase Synchronising Two Generators) Two generators can be synchronised together to provide outputs at the same frequency (or harmonics) and with a phase difference. The amplitude and phase of these outputs can also be modulated providing the capability to perform QAM and QPSK respectively. It is also possible to synchronise more than two generators but the precision is not guaranteed. Carrier Waveforms: Sine, Square, Ramp, Pulse, Arb Phase: Range: -360.0 to +360.0 degrees Resolution: 0.1 degree Accuracy: < 5ns Available from: 19 inch 2U rack mount suitable for one or two generators. GPIB Interface (Option G) ORDERING INFORMATION Four versions of the product are available as follows: TG2511 25MHz Generator with USB and LAN interfaces only. TG2511G 25MHz Generator with USB, LAN and GPIB interfaces. TG5011 50MHz Generator with USB and LAN interfaces only. TG5011G 50MHz Generator with USB, LAN and GPIB interfaces. Each product is supplied with the following: Printed operating manual in English. PDF operating manuals on disk in English, French, German, Italian and Spanish. IEC mains lead appropriate to the geographic market in which it is sold. Software on disk including: Waveform Manager Plus for Windows (version 4), IVI driver, LabView driver, CVI driver, USB driver, LXI discovery tool, TCP example program. Specifications apply for the temperature range 18C to 28C after 30 minutes warm-up, at maximum output into 50 W unless otherwise stated. Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves the right to alter specifications without prior notice. Designed and built in Europe by: Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon, Cambridgeshire. PE29 7DR United Kingdom Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409 Email: sales@aimtti.com Web: www.aimtti.com Brochure Part No. 82100-1390 Iss. 1A Product Summary Company name and product brands Laboratory Power Supplies Bench and system power supplies from 30 watts up to 1200 watts using linear, mixed-mode and PowerFlex regulation technologies. Thurlby Thandar Instruments Ltd. (TTi) is one of Europe's leading manufacturers of test and measurement instruments. Waveform Generators Analog and digital (DDS) function generators, true arbitrary generators, arbitrary/function generators and pulse generators. In the future, however, the full product range will be branded Aim-TTi. Products have been sold under two brand names: TTi and Aim. This changeover will be gradual and many products will continue to carry the TTi or Aim brands for some time to come. Web Addresses (URLs) Precision Measurement Instruments Benchtop DMMs, frequency counters, component measurement instruments (LCR), electronic dc loads, current probes. The preferred URL for obtaining information concerning Aim-TTi products is: www.aimtti.com (international customers) Customers in the UK should use the URL: www.aimtti.co.uk RF and EMC Test Equipment Spectrum analyzers, signal generators, frequency counters, power meters, emc measurement instruments. Customers in the USA should use the URL: www.aimtti.us Note that previous URLs such as www.tti-test.com will continue to operate for the time being. Designed and built in Europe by: Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon, Cambridgeshire PE29 7DR England (United Kingdom) Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409 Email: info@aimtti.com Web: www.aimtti.com