Technical Specification IQ70-HP Family 34-135 V 1.8-48 V 240 W 2250 V dc Half-brick Continuous Input Outputs Max Power Isolation DC-DC Converter The InQor(R) Half-brick converter series is composed of next-generation, board-mountable, isolated, fixed switching frequency dc-dc converters that use synchronous rectification to achieve extremely high power conversion efficiency. Each module is supplied completely encased to provide protection from the harsh environments seen in many industrial and transportation applications. Operational Features * * * * * High efficiencies, up to 91% at full rated load current Delivers full power with minimal derating - no heatsink required Operating input voltage range: 34 - 135 V Fixed frequency switching provides predictable EMI No minimum load requirement Mechanical Features * Industry standard Half-brick pin-out configuration * Standard size: 2.390" x 2.490" x 0.512" (60.6 x 63.1 x 13.0 mm) * Total weight: 5oz (142g) Control Features Protection Features * * * * * On/Off control referenced to input side * Remote sense for the output voltage * Output voltage trim range of -20%, +10% Input under-voltage lockout Output current limit and short circuit protection Active back bias limit Thermal shutdown CONTENTS Page No. Safety Features * 2250 V, 30 MW input-to-output isolation * UL/cUL 60950-1 recognized (US & Canada), basic insulation rating * TUV certified to EN60950-1 * Meets directives which facilitates CE Marking in user's end product * Board and plastic components meet UL94V-0 standard * RoHS compliant (see last page) Product # IQ70xxxHPXxx Phone 1-888-567-9596 Mechanical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IQ70-HP Family Electrical Characteristics 4 3 - 4 IQ70-HP Family Figures 1 5 IQ70018HPx60 (1.8 V, 60 A) Characteristics and Figures-6 - 7 IQ70033HPx57 (3.3 V, 57 A) Characteristics and Figures-8 - 9 IQ70050HPx44 (5.0 V, 44 A) Characteristics and Figures 10 - 11 IQ70120HPx20 (12 V, 20 A) Characteristics and Figures 12 - 13 IQ70150HPx16 (15 V, 16 A) Characteristics and Figures 14 - 15 IQ70240HPx10 (24 V, 10 A) Characteristics and Figures 16 - 17 IQ70280HPx8F (28 V, 8.5 A) Characteristics and Figures 18 - 19 IQ70400HPx06 (40 V, 6.0 A) Characteristics and Figures 20 - 21 IQ70480HPx05 (48 V, 5.0 A) Characteristics and Figures 22 - 23 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 - 27 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 1 Technical Specification IQ70-HP Family IQ70-HP Mechanical Diagram .020 [ 63,14 2.486 2.00 1.400 1.000 0,5 ] [ 50,8 ] [ 35,56 ] [ 25,4 ] .700 [ 17,78 ] .400 [ 10,16 ] 8 7 6 5 +.002 -.005 +0,05 13 -0,12 OVERALL HEIGHT .512 .243 .020 [ 6,17 0,5 ] [ ] .163 [ 4,14 ] 4 .243 .020 [ 6,17 0,5 ] 2.386 .020 [ 60,6 0,5 ] TOP VIEW 1.90 [ 48,3 ] SIDE VIEW 1.90 [ 48,3 ] .233 .020 [ 5,92 0,5 ] 1 2 3 .543 .020 [ 13,79 0,5 ] .400 [ 10,16 ] 1.400 THRU HOLE M3 (SEE NOTE 8) STANDOFFS (4) 4) 5) 6) 7) 8) 9) [ ] BOTTOMSIDE CLEARANCE [ 35,56 ] PIN DESIGNATIONS NOTES 1) 2) 3) +.007 -.010 +0,17 0,69 -0,25 .027 Applied torque per screw should not exceed 6in-lb. (0.7 Nm). Baseplate flatness tolerance is 0.004" (.10 mm) TIR for surface. Pins 1-3, 5-7 are 0.040" (1.02mm) diameter, with 0.080" (2.03mm) diameter standoff shoulders. Pins 4 and 8 are 0.080" (2.03 mm) dia. with 0.125" (3.18 mm) dia. standoff shoulders All Pins: Material: Copper Alloy Finish: Matte Tin over Nickel plate Undimensioned Components are shown for visual reference only Weight: 4.9oz (142g) Threaded or Non-Threaded options available All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) Pin Name Function 1 Vin(+) Positive input voltage 2 ON/OFF 3 Vin(-) 4 Vout(-) 5 SENSE(-) 6 TRIM 7 SENSE(+) Positive remote sense3 8 Vout(+) Positive output voltage TTL input to turn converter on and off, referenced to Vin(-), with internal pull up. Negative input voltage Negative output voltage Negative remote sense1 Output voltage trim2 Notes: 1) 2) 3) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com SENSE(-) should be connected to Vout(-) either remotely or at the converter. Leave TRIM pin open for nominal output voltage. SENSE(+) should be connected to Vout(+) either remotely or at the converter. Doc.# 005-0005255 Rev. F 5/6/10 Page 2 Technical Specification IQ70-HP Family IQ70 FAMILY ELECTRICAL CHARACTERISTICS (all output voltages) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. Typ. ABSOLUTE MAXIMUM RATINGS Input Voltage Non-Operating Operating Operating Transient Protection Isolation Voltage Input to Output Input to Base-Plate Output to Base-Plate Operating Temperature -40 Storage Temperature -55 Voltage at ON/OFF input pin -2 INPUT CHARACTERISTICS Operating Input Voltage Range 34 Input Under-Voltage Lockout Turn-On Voltage Threshold 32.7 Turn-Off Voltage Threshold 30.4 Lockout Voltage Hysteresis Input Over-Voltage Shutdown Recommended External Input Capacitance Input Filter Component Values (L\C) DYNAMIC CHARACTERISTICS Turn-On Transient Turn-On Time Start-Up Inhibit Time 200 Output Voltage Overshoot ISOLATION CHARACTERISTICS Isolation Voltage (dielectric strength) Isolation Resistance Isolation Capacitance (input to output) TEMPERATURE LIMITS FOR POWER DERATING CURVES Semiconductor Junction Temperature Board Temperature Transformer Temperature Maximum Baseplate Temperature, Tb FEATURE CHARACTERISTICS Switching Frequency 255 ON/OFF Control Off-State Voltage 2.4 On-State Voltage -2 ON/OFF Control Pull-Up Voltage Pull-Up Resistance Over-Temperature Shutdown OTP Trip Point Over-Temperature Shutdown Restart Hysteresis RELIABILITY CHARACTERISTICS Calculated MTBF (Telcordia) TR-NWT-000332 Calculated MTBF (MIL-217) MIL-HDBK-217F Field Demonstrated MTBF Max. Units Notes & Conditions 150 135 - V V V 2250 2250 2250 100 125 18 V dc V dc V dc C C V 70 135 V 33.1 30.8 2.3 100 3.4\4.0 33.5 31.2 V V V V F H\F Typical ESR 0.1-0.2 Internal values; see Figure E ms ms % Full load, Vout=90% nom. Figure F Maximum Output Capacitance 10 230 0 250 Continuous Continuous Baseplate temperature See Absolute Maximum Ratings 30 1000 275 M pF See Note 1 125 125 125 100 C C C C Package rated to 150 C UL rated max operating temp 130 C 295 kHz Isolation stage switching freq. is half this 1.8 0.8 V Application notes Figures A & B 5 50 125 10 TBD TBD V k C C Average PCB Temperature 106 Hrs. 80% load, 200LFM, 40 C Ta 106 Hrs. 80% load, 200LFM, 40 C Ta 106 Hrs. See our website for details Note 1: Higher values of isolation capacitance can be added external to the module. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 3 Technical Specification IQ70-HP Family STANDARDS COMPLIANCE Parameter STANDARDS COMPLIANCE UL/cUL 60950-1 EN60950-1 Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 Notes & Conditions File # E194341, Basic insulation Certified by TUV Test on entire assembly; board & plastic components UL94V-0 compliant ESD test, 8 kV - NP, 15 kV air - NP (Normal Performance) Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter QUALIFICATION TESTING Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity Solderability Product # IQ70xxxHPXxx # Units 32 5 5 10 5 5 5 15 pins Phone 1-888-567-9596 Test Conditions 95% rated Vin and load, units at derating point, 1000 hours 10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis 100g minimum, 2 drops in x and y axis, 1 drop in z axis -40 C to 100 C, unit temp. ramp 15 C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10 C to Tmax+10 C, 5 C steps, Vin = min to max, 0-105% load 85 C, 85% RH, 1000 hours, continuous Vin applied except 5 min/day MIL-STD-883, method 2003 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 4 Technical Specification IQ70-HP Family IQ70 FAMILY FIGURES (all output voltages) 120 Typical Current Limit Inception Point Nominal Vout Output Voltage (%) 100 80 Typical Output Voltage at Shutdown 60 40 Vin min Vin nom 20 Vin max 0 5.00 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Load Current (% ) Common Figure 1: Typical startup waveform. Input voltage pre-applied, ON/OFF Pin on Ch 2. Common Figure 2: Output voltage vs. load current showing typical current limit curves and converter shutdown points. 100,000.0 100,000.0 3.3 V 5V 12 V 15 V Trim Resistance (kOhms) Trim Resistance (kOhms) 1.8 V 10,000.0 1,000.0 100.0 10.0 24 V 28 V 40 V 48 V 10,000.0 1,000.0 100.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Increase in Vout (%) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Increase in Vout (%) Common Figure 3: Trim graph for trim-up 1.8 to 12 V outputs. Common Figure 4: Trim graph for trim-up 15 to 48 V outputs. 10,000.0 Trim Resistance (kOhms) All voltages 1,000.0 100.0 10.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Decrease in Vout (%) Common Figure 5: Trim graph for trim down. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 5 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 1.8 V 60 A IQ70018HPx60 IQ70018HPx60 ELECTRICAL CHARACTERISTICS (1.8 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. Max. 4.6 60 4 15 A mA mA V mA A 1.8 1.818 V 0.1 0.1 0.3 0.3 27 1.845 % % mV V 140 30 60 78.0 15,000 mV mV A A V A mA F 10 10 2.3 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5; See Note 2 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve 45 2.5 0.12 230 1.782 -27 1.755 0 0 66.0 70 14 72.0 0.8 1.9 0.1 70 500 -20 2.1 Units Notes & Conditions 2.2 83 88 Vin min; 1.8 Vout ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and 15 F low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Trim-up range is limited below 10% at low line and full load. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 6 Input: Output: Current: Part No.: Technical Specification 100 27 95 24 21 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 18 15 12 9 6 34 Vin 70 Vin 135 Vin 65 34 Vin 70 Vin 3 135 Vin 60 0 0 5 10 15 20 25 30 35 40 45 50 55 60 0 5 10 15 20 Load Current (A) 60 60 50 50 40 40 Iout (A) 70 30 35 40 45 50 55 60 30 20 400 LFM (2.0 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 10 30 Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 70 20 25 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Iout (A) 34 - 135 V 1.8 V 60 A IQ70018HPx60 300 LFM (1.5 m/s) 10 200 LFM (1.0 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 100 LFM (0.5 m/s) 0 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%75%-50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 15 F Tantalum + 1 F Ceramic capacitor. Ch 1: Vout (200 mV/div), Ch 2: Iout (25 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (200 mV/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 7 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 3.3 V 57 A IQ70033HPx57 IQ70033HPx57 ELECTRICAL CHARACTERISTICS (3.3 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. Typ. Max. Units Notes & Conditions INPUT CHARACTERISTICS Maximum Input Current 7.5 A No-Load Input Current 50 60 mA Disabled Input Current 2 3 mA Response to Input Transient 0.24 V Input Terminal Ripple Current 370 mA Recommended Input Fuse Vin min; 3.3 Vout ; in current limit (typ) 500 V/ms, see Figure 6 RMS 15 A Fast acting external fuse recommended 3.3 3.333 V Over Line 0.1 0.3 % Over Load 0.1 0.3 % -50 50 mV 3.218 3.383 V 180 360 mV Full load 25 50 mV Full load 57 A Subject to thermal derating 68.4 74.1 A Output voltage 10% Low OUTPUT CHARACTERISTICS Output Voltage Set Point 3.267 Output Voltage Regulation Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise 20 MHz bandwidth; see Note 1 Peak-to-Peak 0 RMS Operating Output Current Range Output DC Current-Limit Inception Over sample, line, load, temperature & life 0 62.7 Output DC Current-Limit Shutdown Voltage 1.7 V Back-Drive Current Limit while Enabled 1.2 A Negative current drawn from output Back-Drive Current Limit while Disabled 0.1 mA Negative current drawn from output F Vout nominal at full load (resistive load) Maximum Output Capacitance 10,000 Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) 80 mV 50% to 75% to 50% Iout max Settling Time 400 s To within 1% Vout nom 10 % Across Pins 8&4; Common Figures 3-5; See Note 2 10 % Across Pins 8&4 4.2 V Over full temp range Output Voltage Trim Range -20 Output Voltage Remote Sense Range Output Over-Voltage Protection 3.9 4.0 EFFICIENCY 100% Load 88 % See Figure 1 for efficiency curve 50% Load 91 % See Figure 1 for efficiency curve Note 1: Output is terminated with 1 F ceramic and 15 F low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Trim-up range is limited below 10% at low line and full load. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 8 Input: Output: Current: Part No.: Technical Specification 100 34 - 135 V 3.3 V 57 A IQ70033HPx57 30 27 95 24 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 34 Vin 70 Vin 135 Vin 65 21 18 15 12 9 34 Vin 70 Vin 6 3 60 135 Vin 0 0 6 12 18 24 30 36 42 48 54 60 0 6 12 18 Load Current (A) 30 36 42 48 54 60 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 60 60 54 54 48 48 42 42 36 36 Iout (A) Iout (A) 24 30 24 30 24 18 18 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 12 200 LFM (1.0 m/s) 6 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 12 200 LFM (1.0 m/s) 6 100 LFM (0.5 m/s) 0 100 LFM (0.5 m/s) 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 15 F Tantalum + 1 F Ceramic capacitor. Ch 1: Vout (200 mV/div), Ch 2: Iout (25 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (500 mV/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 9 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 5.0 V 44 A IQ70050HPx44 IQ70050HPx44 ELECTRICAL CHARACTERISTICS (5.0 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. Max. 9.0 60 3 15 A mA mA V mA A 5 5.05 V 0.1 0.1 0.3 0.3 75 5.125 % % mV V 340 50 44 57.2 8,000 mV mV A A V A mA F 10 10 6.4 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5; See Note 2 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve 45 2 0.35 450 4.95 -75 4.875 0 0 48.4 170 23 52.8 2.7 0.55 0.4 200 400 -20 5.9 Units Notes & Conditions 6.1 87 90 Vin min; 5 Vout ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and 15 F low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Trim-up range is limited below 10% at low line and full load. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 10 Input: Output: Current: Part No.: 100 40 95 35 90 30 Power Dissipation (W) Efficiency (%) Technical Specification 85 80 75 70 34 Vin 70 Vin 135 Vin 65 25 20 15 10 34 Vin 70 Vin 5 135 Vin 60 0 0 4 8 12 16 20 24 28 32 36 40 44 0 4 8 12 16 Load Current (A) 20 24 28 32 36 40 44 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 48 48 44 44 40 40 36 36 32 32 28 28 Iout (A) Iout (A) 34 - 135 V 5.0 V 44 A IQ70050HPx44 24 20 16 24 20 16 400 LFM (2.0 m/s) 12 300 LFM (1.5 m/s) 8 200 LFM (1.0 m/s) 4 400 LFM (2.0 m/s) 12 300 LFM (1.5 m/s) 8 200 LFM (1.0 m/s) 4 100 LFM (0.5 m/s) 0 100 LFM (0.5 m/s) 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 15 F Tantalum + 1 F Ceramic capacitor. Ch 1: Vout (500 mV/div), Ch 2: Iout (10 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (500 mV/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 11 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 12 V 20 A IQ70120HPx20 IQ70120HPx20 ELECTRICAL CHARACTERISTICS (12 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. Max. 9.3 70 3 15 A mA mA V mA A 12 12.12 V 0.1 0.1 0.3 0.3 180 12.300 % % mV V 200 30 20 26.0 1,500 mV mV A A V A mA F 10 10 15.3 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5; see Note 2 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve 55 2 0.75 430 11.88 -180 11.700 0 0 22.0 100 13 24.0 6.5 0.5 1 270 100 -20 14.0 Units Notes & Conditions 14.6 91 93 Vin min; 12 Vout ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and 15 F low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Trim-up range is limited below 10% at low line and full load. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 12 Input: Output: Current: Part No.: Technical Specification 100 34 - 135 V 12 V 20 A IQ70120HPx20 30 27 95 24 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 34 Vin 70 Vin 135 Vin 65 21 18 15 12 9 34 Vin 70 Vin 6 3 60 135 Vin 0 0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 10 12 14 16 18 20 Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 22 22 20 20 18 18 16 16 14 14 Iout (A) Iout (A) 8 Load Current (A) 12 10 8 12 10 8 6 6 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 4 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 4 200 LFM (1.0 m/s) 2 200 LFM (1.0 m/s) 2 100 LFM (0.5 m/s) 0 100 LFM (0.5 m/s) 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 15 F Tantalum + 1 F Ceramic capacitor. Ch 1: Vout (500 mV/div), Ch 2: Iout (10 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (1 V/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 13 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 15 V 16 A IQ70150HPx16 IQ70150HPx16 ELECTRICAL CHARACTERISTICS (15 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. Max. 9.4 70 3 15 A mA mA V mA A 15 15.15 V 0.1 0.1 0.3 0.3 225 15.375 % % mV V 260 40 16 20.8 1,000 mV mV A A V A mA F 10 10 19.1 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5; see Note 2 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve 55 2 0.9 490 14.85 -225 14.625 0 0 17.6 130 22 19.2 8.5 0.35 1.5 500 80 -20 17.6 Units Notes & Conditions 18.3 90 93 Vin min; 12 Vout ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and 15 F low-ESR tantalum capacitors. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Trim-up range is limited below 10% at low line and full load. Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 14 Input: Output: Current: Part No.: Technical Specification 100 35 95 30 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 25 20 15 10 34 Vin 70 Vin 135 Vin 65 34 Vin 70 Vin 5 135 Vin 60 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0 1 2 3 4 5 Load Current (A) 6 7 8 9 10 11 12 13 14 15 16 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 18 18 16 16 14 14 12 12 Iout (A) Iout (A) 34 - 135 V 15 V 16 A IQ70150HPx16 10 8 6 10 8 6 400 LFM (2.0 m/s) 4 400 LFM (2.0 m/s) 4 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 2 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 2 100 LFM (0.5 m/s) 100 LFM (0.5 m/s) 0 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 15 F Tantalum + 1 F Ceramic capacitor. Ch 1: Vout (1 V/div), Ch 2: Iout (5 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (1 V/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 15 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 24 V 10 A IQ70240HPx10 IQ70240HPx10 ELECTRICAL CHARACTERISTICS (24 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. 15 24 24.24 V 0.1 0.1 0.3 0.3 360 24.60 % % mV V 400 70 10 13.0 400 mV mV A A V A mA F 10 10 30.5 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve -360 23.40 0 0 11.0 200 36 12.0 15 0.15 2.5 10.5 60 4 1300 80 -20 28.1 Units Notes & Conditions A mA mA V mA A 45 2.5 1.3 500 23.76 Max. 29.3 88 92 Vin min; trim-up ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and capacitor. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 16 Input: Output: Current: Part No.: 100 40 95 35 90 30 Power Dissipation (W) Efficiency (%) Technical Specification 85 80 75 70 34 Vin 70 Vin 135 Vin 65 25 20 15 10 34 Vin 70 Vin 5 135 Vin 60 0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 Load Current (A) 4 5 6 7 8 9 10 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 11 11 10 10 9 9 8 8 7 7 Iout (A) Iout (A) 34 - 135 V 24 V 10 A IQ70240HPx10 6 5 4 6 5 4 3 3 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 2 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 2 200 LFM (1.0 m/s) 1 200 LFM (1.0 m/s) 1 100 LFM (0.5 m/s) 0 100 LFM (0.5 m/s) 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 1 F ceramic capacitor. Ch 1: Vout Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (2 V/div), Ch 2: Vin (50 V/div). (2 V/div), Ch 2: Iout (2.5 A/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 17 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 28 V 8.5 A IQ70280HPx8F IQ70280HPx8F ELECTRICAL CHARACTERISTICS (28 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. 15 28 28.28 V 0.1 0.1 0.3 0.3 420 28.70 % % mV V 460 80 8.5 11.1 250 mV mV A A V A mA F 10 10 35.6 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve -420 27.30 0 0 9.35 230 40 10.2 17 0.17 3 10.4 60 3 1500 80 -20 32.8 Units Notes & Conditions A mA mA V mA A 45 2 2 420 27.72 Max. 34.2 89 92 Vin min; trim-up ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and capacitor. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 18 Input: Output: Current: Part No.: Technical Specification 100 35 95 30 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 34 Vin 70 Vin 135 Vin 65 25 20 15 10 34 Vin 70 Vin 5 135 Vin 60 0.00 0 0.85 1.70 2.55 3.40 4.25 5.10 5.95 6.80 7.65 8.50 0.00 0.85 1.70 2.55 Load Current (A) 3.40 4.25 5.10 5.95 6.80 7.65 8.50 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 9 9 8 8 7 7 6 6 Iout (A) Iout (A) 34 - 135 V 28 V 8.5 A IQ70280HPx8F 5 4 3 5 4 3 400 LFM (2.0 m/s) 2 400 LFM (2.0 m/s) 2 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 1 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 1 100 LFM (0.5 m/s) 100 LFM (0.5 m/s) 0 0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 1 F ceramic capacitor. Ch 1: Vout (2 V/div), Ch 2: Iout (2.5 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (2 V/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 19 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 40 V 6.0 A IQ70400HPx06 IQ70400HPx06 ELECTRICAL CHARACTERISTICS (40 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. 15 40 40.4 V 0.1 0.1 0.3 0.3 600 41.00 % % mV V 400 60 6 7.8 150 mV mV A A V A mA F 10 10 50.8 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve -600 39.00 0 0 6.6 200 30 7.2 23 0.13 4 10.5 60 3 2250 80 -20 46.8 Units Notes & Conditions A mA mA V mA A 50 2 2.6 440 39.6 Max. 48.8 89 92 Vin min; trim-up ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and capacitor. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 20 Input: Output: Current: Part No.: Technical Specification 100 35 95 30 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 34 Vin 70 Vin 135 Vin 65 25 20 15 10 34 Vin 70 Vin 5 135 Vin 60 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 0.0 0.5 1.0 1.5 2.0 Load Current (A) 6.0 6.0 5.0 5.0 4.0 4.0 Iout (A) 7.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 3.0 2.0 400 LFM (2.0 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 1.0 3.0 Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 7.0 2.0 2.5 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Iout (A) 34 - 135 V 40 V 6.0 A IQ70400HPx06 300 LFM (1.5 m/s) 1.0 200 LFM (1.0 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 100 LFM (0.5 m/s) 0.0 0.0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 1 F ceramic capacitor. Ch 1: Vout (2 V/div), Ch 2: Iout (2.5 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (2 V/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 21 Input: Output: Current: Part No.: Technical Specification 34 - 135 V 48 V 5.0 A IQ70480HPx05 IQ70480HPx05 ELECTRICAL CHARACTERISTICS (48 Vout) Ta = 25 C, airflow rate = 300 LFM, Vin = 70 V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. INPUT CHARACTERISTICS Maximum Input Current No-Load Input Current Disabled Input Current Response to Input Transient Input Terminal Ripple Current Recommended Input Fuse OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Output Voltage during Load Current Transient Step Change in Output Current (0.1 A/s) Settling Time Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection EFFICIENCY 100% Load 50% Load Typ. 15 48 48.48 V 0.1 0.1 0.3 0.3 720 49.20 % % mV V 360 60 5 6.5 100 mV mV A A V A mA F 10 10 61.0 mV s % % V 50% to 75% to 50% Iout max To within 1% Vout nom Across Pins 8&4; Common Figures 3-5 Across Pins 8&4 Over full temp range % % See Figure 1 for efficiency curve See Figure 1 for efficiency curve -720 46.80 0 0 5.5 180 30 6.0 27 0.1 5 10.4 70 3 2700 80 -20 56.2 Units Notes & Conditions A mA mA V mA A 55 2 3.2 490 47.52 Max. 58.6 90 92 Vin min; trim-up ; in current limit (typ) 500 V/ms, see Figure 6 RMS Fast acting external fuse recommended Over sample, line, load, temperature & life 20 MHz bandwidth; see Note 1 Full load Full load Subject to thermal derating Output voltage 10% Low Negative current drawn from output Negative current drawn from output Vout nominal at full load (resistive load) Note 1: Output is terminated with 1 F ceramic and capacitor. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 22 Input: Output: Current: Part No.: Technical Specification 100 35 95 30 Power Dissipation (W) Efficiency (%) 90 85 80 75 70 34 Vin 70 Vin 135 Vin 65 25 20 15 10 34 Vin 70 Vin 5 135 Vin 60 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0.5 1.0 1.5 Load Current (A) 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. 6.0 6.0 5.5 5.5 5.0 5.0 4.5 4.5 4.0 4.0 3.5 3.5 Iout (A) Iout (A) 34 - 135 V 48 V 5.0 A IQ70480HPx05 3.0 2.5 2.0 3.0 2.5 2.0 400 LFM (2.0 m/s) 1.5 300 LFM (1.5 m/s) 1.0 200 LFM (1.0 m/s) 0.5 400 LFM (2.0 m/s) 1.5 300 LFM (1.5 m/s) 1.0 200 LFM (1.0 m/s) 0.5 100 LFM (0.5 m/s) 0.0 100 LFM (0.5 m/s) 0.0 25 40 55 70 85 Ambient Air Temperature (C) 25 40 55 70 85 Ambient Air Temperature (C) Figure 3: Encased converter (without heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 4: Encased converter (with 1/2" heatsink) max. output power derating vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM. Air flows across the converter from input to output (nominal input voltage). Figure 5: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1 A/s). Load cap: 1 F ceramic capacitor. Ch 1: Vout (2 V/div), Ch 2: Iout (2.5 A/div). Figure 6: Output voltage response to step-change in input voltage (500 V/ms). Load cap: 100 F, electrolytic output capacitance. Ch 1: Vout (5 V/div), Ch 2: Vin (50 V/div). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 23 Technical Specification IQ70-HP Family BASIC OPERATION AND FEATURES CONTROL FEATURES This converter series uses a two-stage power topology. The first stage is a buck-converter that output voltage constant over variations in line, temperature. The second stage uses a transformer the functions of input/output isolation and voltage step-down to achieve the output voltage required. REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits the user to control when the converter is on or off. This input is referenced to the return terminal of the input bus, Vin(-). The ON/OFF signal is active low (meaning that a low turns the converter on). Figure A details four possible circuits for driving the ON/OFF pin. Figure B is a detailed look of the internal ON/ OFF circuitry. conversion keeps the load, and to provide step-up or Both the first stage and the second stage switch at a fixed frequency for predictable EMI performance. Rectification of the transformer's output is accomplished with synchronous rectifiers. These devices, which are MOSFETs with a very low on-state resistance, dissipate far less energy than Schottky diodes. This is the primary reason that the converter has such high efficiency, even at very low output voltages and very high output currents. These converters are offered totally encased to withstand harsh environments and thermally demanding applications. Dissipation throughout the converter is so low that it does not require a heatsink for operation in many applications; however, adding a heatsink provides improved thermal derating performance in extreme situations. This series of converters use the industry standard footprint and pin-out configuration. ON/OFF ON/OFF Vin(_) Vin(_) Remote Enable Circuit REMOTE SENSE(+) (Pins 7 and 5): The SENSE(+) inputs correct for voltage drops along the conductors that connect the converter's output pins to the load. Pin 7 should be connected to Vout(+) and Pin 5 should be connected to Vout(-) at the point on the board where regulation is desired. A remote connection at the load can adjust for a voltage drop only as large as that specified in this datasheet, that is [Vout(+) - Vout(-)] - [Vsense(+) - Vsense(-)] < Sense Range % x Vout Pins 7 and 5 must be connected for proper regulation of the output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than its specified value. Note: the output over-voltage protection circuit senses the voltage across the output (pins 8 and 4) to determine when it should trigger, not the voltage across the converter's sense leads (pins 7 and 5). Therefore, the resistive drop on the board should be small enough so that output OVP does not trigger, even during load transients. Negative Logic (Permanently Enabled) 5V ON/OFF TTL/ CMOS 50k ON/OFF ON/OFF Vin(_) Vin(_) Open Collector Enable Circuit 5V 50k TTL Direct Logic Drive 100pF Figure A: Various circuits for driving the ON/OFF pin. Vin(_) Figure B: Internal ON/OFF pin circuitry Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 24 Technical Specification IQ70-HP Family OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the user to adjust the output voltage across the sense leads up or down according to the trim range specifications. To decrease the output voltage, the user should connect a resistor between Pin 6 and Pin 5 (SENSE(-) input). For a desired decrease of the nominal output voltage, the value of the resistor should be Rtrim-down = - 10.22 (511 % ) (kW) where % = Vnominal - Vdesired Vnominal x 100% To increase the output voltage, the user should connect a resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired increase of the nominal output voltage, the value of the resistor should be Rtrim-up = where ( 5.11VOUT x (100+%) 1.225% _ 511 _ 10.22 % ) (kW) Vout = Nominal Output Voltage Trim graphs show the relationship between the trim resistor value and Rtrim-up and Rtrim-down, showing the total range the output voltage can be trimmed up or down. Note: the TRIM feature does not affect the voltage at which the output over-voltage protection circuit is triggered. Trimming the output voltage too high may cause the over-voltage protection circuit to engage, particularly during transients. It is not necessary for the user to add capacitance at the Trim pin. The node is internally bypassed to eliminate noise. Total DC Variation of VOUT: For the converter to meet its full specifications, the maximum variation of the dc value of VOUT, due to both trimming and remote load voltage drops, should not be greater than that specified for the output voltage trim range. Product # IQ70xxxHPXxx Phone 1-888-567-9596 PROTECTION FEATURES Input Under-Voltage Lockout: The converter is designed to turn off when the input voltage is too low, helping avoid an input system instability problem, described in more detail in the application note titled "Input System Instability" on our website. The lockout circuitry is a comparator with dc hysteresis. When the input voltage is rising, it must exceed the typical TurnOn Voltage Threshold value (listed on the specifications page) before the converter will turn on. Once the converter is on, the input voltage must fall below the typical Turn-Off Voltage Threshold value before the converter will turn off. Output Current Limit: The maximum current limit remains constant as the output voltage drops. However, once the impedance of the load across the output is small enough to make the output voltage drop below the specified Output DC CurrentLimit Shutdown Voltage, the converter turns off. The converter then enters a "hiccup mode" where it repeatedly turns on and off at a 5 Hz (nominal) frequency with a 5% duty cycle until the short circuit condition is removed. This prevents excessive heating of the converter or the load board. Output Over-Voltage Limit: If the voltage across the output pins exceeds the Output Over-Voltage Protection threshold, the converter will immediately stop switching. This prevents damage to the load circuit due to 1) excessive series resistance in output current path from converter output pins to sense point, 2) a release of a short-circuit condition, or 3) a release of a current limit condition. Load capacitance determines exactly how high the output voltage will rise in response to these conditions. After 200 ms the converter will automatically restart. Over-Temperature Shutdown: A temperature sensor on the converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the temperature at the sensed location reaches the Over-Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 25 Technical Specification IQ70-HP Family APPLICATION CONSIDERATIONS Input System Instability: This condition can occur because any dc-dc converter appears incrementally as a negative resistance load. A detailed application note titled "Input System Instability" is available on the SynQor website which provides an understanding of why this instability arises, and shows the preferred solution for correcting it. Application Circuits: Figure C provides a typical circuit diagram which details the input filtering and voltage trimming. Vin(+) External Input Filter Vin Electrolytic Capacitor Vout(+) Vsense(+) Trim ON/OFF Vsense(_) Vin(_) Rtrim-up or Rtrim-down Cload Iload Vout(_) Figure C: Typical application circuit (negative logic unit, permanently enabled). Input Filtering and External Capacitance: Figure D provides a diagram showing the internal input filter components. This filter dramatically reduces input terminal ripple current, which otherwise could exceed the rating of an external electrolytic input capacitor. The recommended external input capacitance is specified in the Input Characteristics section on the Electrical Characteristics page. More detailed information is available in the application note titled "EMI Characteristics" on the SynQor website. L Vin(+) C Vin(_) Figure D: Internal Input Filter Diagram (component values listed on the specifications page). Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 26 Technical Specification IQ70-HP Family Startup Inhibit Period: The Startup Inhibit Period ensures that the converter will remain off for approximately 200 ms when it is shut down for any reason. When an output short is present, this generates a 5 Hz "hiccup mode," which prevents the converter from overheating. In all, there are seven ways that the converter can be shut down, initiating a Startup Inhibit Period: * Input Under-Voltage Lockout When the ON/OFF pin goes high after t2, the Startup Inhibit Period has elapsed, and the output turns on within the typical Turn-On Time. Thermal Considerations: The maximum operating base-plate temperature, TB, is 100 C. As long as the user's thermal system keeps TB < 100 C, the converter can deliver its full rated power. A power derating curve can be calculated for any heatsink that is attached to the base-plate of the converter. It is only necessary to determine the thermal resistance, RTHBA, of the chosen heatsink between the base-plate and the ambient air for a given airflow rate. This information is usually available from the heatsink vendor. The following formula can the be used to determine the maximum power the converter can dissipate for a given thermal condition if its base-plate is to be no higher than 100 C. * Input Over-Voltage Shutdown * Output Over-Voltage Protection * Over Temperature Shutdown * Current Limit * Short Circuit Protection * Turned off by the ON/OFF input Figure E shows three turn-on scenarios, where a Startup Inhibit Period is initiated at t0, t1, and t2: Before time t0, when the input voltage is below the UVL threshold, the unit is disabled by the Input Under-Voltage Lockout feature. When the input voltage rises above the UVL threshold, the Input Under-Voltage Lockout is released, and a Startup Inhibit Period is initiated. At the end of this delay, the ON/OFF pin is evaluated, and since it is active, the unit turns on. At time t1, the unit is disabled by the ON/OFF pin, and it cannot be enabled again until the Startup Inhibit Period has elapsed. max Pdiss = 100 C - TA RTHBA This value of power dissipation can then be used in conjunction with the data shown in Figure 2 to determine the maximum load current (and power) that the converter can deliver in the given thermal condition. For convenience, power derating curves for an encased converter without a heatsink and with a typical heatsink are provided for each output voltage. Vin Under-Voltage Lockout TurnOn Threshold ON/OFF (neg logic) ON OFF ON Vout OFF ON 9ms (typical turn on time) 200ms (typical start-up inhibit period) t1 t0 200ms 200ms t t2 Figure E: Startup Inhibit Period (turn-on time not to scale) Product # IQ70xxxHPXxx Phone 1-888-567-9596 www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 27 Technical Specification IQ70-HP Family PART NUMBERING SYSTEM ORDERING INFORMATION The part numbering system for SynQor's dc-dc converters follows the format shown in the example below. The tables below show the valid model numbers and ordering options for converters in this product family. When ordering SynQor converters, please ensure that you use the complete 15 character part number consisting of the 12 character base part number and the additional characters for options. Add "-G" to the model number for 6/6 RoHS compliance. IQ 70 480 H P x 05 N R S - G 6/6 RoHS Options (see Ordering Information) Output Current Thermal Design Performance Level Package Size Output Voltage Input Voltage Model Number Continuous Input Voltage Output Voltage IQ70018HPw60NRS IQ70033HPw57NRS IQ70050HPw44NRS IQ70120HPw20NRS IQ70150HPw16NRS IQ70240HPw10NRS IQ70280HPw8FNRS IQ70400HPw06NRS IQ70480HPw05NRS 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 34 - 135 V 1.8 V 3.3 V 5.0 V 12 V 15 V 24 V 28 V 40 V 48 V Maximum Output Current 60 A 57 A 44 A 20 A 16 A 10 A 8.5 A 6.0 A 5.0 A Product Family The first 12 characters comprise the base part number and the last 3 characters indicate available options. The "-G" suffix indicates 6/6 RoHS compliance. Application Notes A variety of application notes and technical white papers can be downloaded in pdf format from our website. RoHS Compliance: The EU led RoHS (Restriction of Hazardous Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is 6/6 RoHS compliant. For more information please refer to SynQor's RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. The following options must be included in place of the w x y z spaces in the model numbers listed above. Options Description: w x y z Thermal Design Enable Logic Pin Style Feature Set C - Encased with Threaded Baseplate D - Encased with Non-Threaded Baseplate N - Negative R - 0.180" S - Standard Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options. PATENTS SynQor holds the following patents, one or more of which might apply to this product: 5,999,417 6,594,159 6,927,987 7,119,524 6,222,742 6,731,520 7,050,309 7,269,034 6,545,890 6,894,468 7,072,190 7,272,021 6,577,109 6,896,526 7,085,146 7,272,023 Contact SynQor for further information: Phone: Toll Free: Fax: E-mail: Web: Address: Product # IQ70xxxHPXxx 978-849-0600 888-567-9596 978-849-0602 power@synqor.com www.synqor.com 155 Swanson Road Boxborough, MA 01719 USA Phone 1-888-567-9596 Warranty SynQor offers a two (2) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor. www.synqor.com Doc.# 005-0005255 Rev. B 5/6/10 Page 28