Du line
®
Fieldbus Installationbus
Specifications are subject to change without notice (16.06.2006) 1
Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group
Type: Dupline®
Housing
Input type
Channels
Inputs
Colour/Input type
Supply
Ordering keyProduct Description
The G3486 0058 230 wire-
less base station is dedi -
cated for G8x86 440x 703
wireless switches. The units
com municate at 868 MHz.
The base station is built into
a standard H4 plastic hous-
ing. It should not be installed
in a metal cabinet or other
type of installation that might
reduce the range.
The wireless Base unit is
Capable of controlling a
unlimited number of wireless
switches. The wireless sys-
tem is built for smarthouse.
• Dupline transceiver for building automation applications
• Easy to install in both old and new installations
• Unlimited number of connected wireless switches
G8x86 440x 703
• DIN-rail mounting
• Range up to 100 m in open air
• Easy to operate
Input Specifications
•Wireless communication at 868 MHz.
Supply Specifications
Power supply AC types Overvoltage cat. III (IEC60664)
Rated operational voltage
through term. 21 & 22 230 230 VAC, ±15%
Frequency 45 to 65 Hz
Voltage drop-out 40 ms
Rated operational power Typ. 3 VA
Power dissipation 3 W
Rated impulse voltage 230 4 kV
Dielectric voltage
Supply – Dupline® 4 kVAC (rms)
Dupline Wireless Base Unit
Type G3486 0058 230
General Specification
Power ON Delay Typ . 2 s
Indication of
Power ON Green LED
Dupline®signal Yellow LED
Wireless communication ON Green LED
Association Red LED
Disable RF Red LED
Environment
Protection degree IP 20
Pollution degree 3 (IEC 60664)
Operating temperature -20°C to +50°C (-4° to + 122°F)
Storage temperature -50°C to +85°C (-58° to +185°F)
Humidity (non-condensing) 20 to 80%
Mechanical resistance
Shock 15 G (11 ms)
Vibration 2 G (6 to 55 Hz)
Dimensions 72 x 77 x 70 mm
Material
(see “Techical information”) H4 housing
Weight 250 g
Special conditions The base should not be
installed in shielded boxes
such as metal or plated, as
these will reduce the range
to the associated units.
G 3486 0058 230
Du line
®
Fieldbus Installationbus
2Specifications are subject to change without notice (16.06.2006)
Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group
Mode of operation
The wireless G8x86 44xx 703
switches are programmed as
standard Fuga/Opus switches
(but with no channel coding
for (I/O 5-8, as the leds auto-
matically follow the buttons).
The communication between
the G8x86 44xx 703 wireless
switch and the G3486 0058
230 base is established in the
following way:
The used Dupline adresses of
wireless devices are all pro-
grammed at the wireless
device. The only "special"
interaction regarding wireless
devices is the association
process.
This process makes sure that
your wireless devices are not
disturbed by the devices of
your neighbour.
To associate a device with the
base:
1) Press the "mode" button
on the base. The association
led lights up.
2) Press a button on the wire-
less device to be associated.
- All leds on the device will
light up for about 1 second.
3) Press the "mode" button
on the base unit until both
Association and disabled-leds
are off. This indicates "normal
operation".
If the connection from a wire-
less device fails, alle leds will
flash briefly after trying to
communicate with the base
unit three times.
If a device associated with
base A is in sight of bases A
and B and you want to reas-
sociate the device with base
B, do the following:
1) Select the "Disabled" mode
on base A.
2) Select the "Associate"
mode on base B.
3) Press a button on the wire-
less device to be associated.
- All leds on the device will
light up for about 1 second.
4) Press the "mode" button
on both base units until both
Association and disabled-leds
are off. This indicates "normal
operation".
The LEDs:
The "Power" LED indicates
that the unit is powered.
(230Vac)
The "Dupline OK" LED indi-
cates detected Dupline signal.
The "RF" LED indicates
received wireless communi-
cation directed to this base.
The "Associate" LED indi-
cates the association mode.
The "Disabled" LED indicates
that the base ignores any
wireless communications.
G82864406703
G81864407703
Mode
I1
I2
I3
I4
I1
I3
I2
I4
Max.
100 m
868 MHz
G34860058230G3800XXXX
Dupline®
1 2 1 2
Power
Dupline®
RF
Associate
Disable
