EMIF02-MIC06F3 2-line IPADTM EMI filter and ESD protection Datasheet - production data Description The EMIF02-MIC06F3 is a highly integrated device designed to suppress EMI/RFI noise for dual microphone line filtering. The EMIF02-MIC06F3 Flip-Chip packaging means the package size is equal to the die size. That's why EMIF02-MIC06F3 is a very small device. Lead -free Flip-chip package (8 bumps) Additionally, this filter includes an ESD protection circuitry which prevents damage to the application when subjected to ESD surges up to 15 kV. Features Figure 1. Pin configuration (bump side) * 2-line symmetrical low-pass filter * Lead-free package * Very low PCB space consuming: < 1.5 3 2 1 MIC Bias ECI Op n Gnd Mic2p B On A Gnd Mic2n C mm2 * Very thin package: 0.65 mm * High efficiency in ESD suppression IEC 61000-4-2 level 4 * High reliability offered by monolithic integration * High reduction of parasitic elements through integration and wafer level packaging A Complies with the following standards * IEC 61000-4-2 level 4: - 15 kV (air discharge) - 8 kV (contact discharge) B2 and C2 GND bumps must be conneted together on the PCB Application * Mobile phones (differential microphone filtering and ESD protection) TM: IPAD is a trademark of STMicroelectronics. May 2014 This is information on a product in full production. DocID15195 Rev 5 1/8 www.st.com Characteristics 1 EMIF02-MIC06F3 Characteristics Figure 2. Configuration ECI A2 GND GND Mic Bias A3 C11 B1 GND C21 R11 R31 R21 B3 Mic2p to ASIC Mic2n R22 C1 C12 GND GND C3 R12 GND C22 GND B2 and C2 are ground pins ECI pin connection The ECI pin (enhancement control interface) is an input pin for the audio pre-amplifier chip which detects the voltage of the microphone line MIC2P in case the user presses the onhook/off-hook button on the headset. When the user selects off-hook using the headset button, the MIC2P is shorted to MIC2N which is grounded. If your design does not support the ECI feature, the ECI pin must be left open (not connected). Table 1. Absolute ratings (limiting values) Symbol VPP 2/8 Parameter and test conditions Pins B1 and C1: ESD discharge IEC 61000-4-2, level 4 air discharge contact discharge Pins A2, A3, B2, B3, C2, C3: ESD discharge IEC 61000-4-2, level 1 air discharge contact discharge Value 15 8 Unit kV 2 2 PD Power dissipation at Tamb = 25 C 60 mW Tj Maximum junction temperature 125 C Top Operating temperature range - 40 to + 85 C Tstg Storage temperature range - 55 to + 150 C DocID15195 Rev 5 EMIF02-MIC06F3 Characteristics Figure 3. Electrical characteristics (definitions) I Symbol VBR = IRM = Parameter Breakdown voltage Leakage current @ VRM RI/O = Series resistance between input and output Line capacitance Cline = VBR VRM IR IRM IRM IR VRM VBR V Table 2. Electrical characteristics - values (Tamb = 25 C) Symbol Test conditions VBR IR = 1 mA IRM VRM = 3 V per line Typ. Max. Unit 14 V 100 nA R11 1.9 2 2.1 k R12 0.8 1 1.2 k R21, R22 1.76 2.2 2.64 k R31 20 25 30 0.8 1 nF C11, C12 VR = 0 V C21, C22 VR = 0 V 1 Figure 4. Attenuation simulation with 1 k input and 10 k output 0 Min. db 1.25 nF Figure 5. Analog crosstalk measurement 0.00 db -10.00 -10 -20.00 -20 -30.00 -30 50 measurements -40.00 -40 -50.00 -50 Input: 1 k Output: 10 k AC simulation -60 -70 -60.00 50 simulations -70.00 -80.00 -80 -90.00 -90 F (Hz) F (Hz) -100.00 -100 10 100 1k 10k 100k 1M 10M 100M 1G DocID15195 Rev 5 100.0k 1.0M Mic2p-On 10.0M 100.0M Mic2n-Op 1.0G 3/8 8 Characteristics EMIF02-MIC06F3 Figure 6. ESD response to IEC 61000-4-2 (+15 kV air discharge) on Mic2p Figure 7. ESD response to IEC 61000-4-2 (-15 kV air discharge) on Mic2p 10 V/div 10 V/div Input Input 5 V/div 5 V/div Output Output 500 ns/div 500 ns/div Figure 8. ESD response to IEC 61000-4-2 (+15 kV air discharge) on Mic2n Figure 9. ESD response to IEC 61000-4-2 (-15 kV air discharge) on Mic2n 10 V/div 10 V/div Input Input 2 V/div 2 V/div Output Output 200 ns/div 200 ns/div Figure 10. Line capacitance versus applied voltage CLINE (pF) 1 200.00 1 000.00 800.00 F = 1 Mhz VOSC = 30 mV rms Tj = 25 C 600.00 400.00 200.00 VLINE (V) 0.00 0 4/8 0.5 1 1.5 DocID15195 Rev 5 2 2.5 3 EMIF02-MIC06F3 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 11. Flip Chip package dimensions 400 m 40 605 m 55 255 m 40 1.20 mm 30 m 400 m 40 200 m 1.20 mm 30 m Figure 12. Footprint recommendations 200 m 2 Package information Figure 13. Marking Dot, ST logo ECOPACK status xx = marking z = manufacturing location yww = datecode (y = year Copper pad Diameter: 220m recommended 260m maximum Solder mask opening: 300m minimum x x z y ww Solder stencil opening : 220m recommended DocID15195 Rev 5 5/8 8 Package information EMIF02-MIC06F3 Figure 14. Flip Chip tape and reel specification 2.0 0.05 O 1.55 0.05 4.0 0.1 1.75 0.1 Dot identifying Pin A1 location 3.5 0.05 1.30 0.05 xxz yww 4.0 0.1 User direction of unreeling DocID15195 Rev 5 ST xxz yww All dimensions are typical values in mm ST xxz yww 1.30 0.05 0.69 0.05 6/8 ST 8.0 +0.3/-0.1 0.22 0.02 EMIF02-MIC06F3 3 Ordering information Ordering information Figure 15. Ordering information scheme EMIF yy - xxx zz Fx EMI filter Number of lines Information x = resistance value (Ohms) z = capacitance value / 10(pF) or 3 letters = application 2 digits = version Package F = Flip Chip x = 3: lead-free, pitch = 400 m Table 3. Ordering information Order code Marking Package Weight Base qty Delivery mode EMIF02-MIC06F3 JB Flip Chip 1.8 mg 5000 Tape and reel 7" Note: More information is available in the application notes AN2348: "Flip Chip: Package description and recommendations for use" AN1751: "EMI Filters: Recommendations and measurements" 4 Revision history Table 4. Document revision history Date Revision Changes 21-Nov-2008 1 Initial release 05-Mar-2009 2 Updated Figure 4 and Figure 11. 07-Apr-2010 3 Updated tolerance Figure 11. 23-Sep-2011 4 Added ECI pin connection on page 2. 26-May-2014 5 Updated Figure 1 and Figure 14. DocID15195 Rev 5 7/8 8 EMIF02-MIC06F3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER'S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR "AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL" INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2014 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 8/8 DocID15195 Rev 5