Embedded Systems Design Series Digital Logic Trainers DL-010 Combinational Logic Trainer Global Specialties' DL-010 is first in its series of embedded systems design trainers. The DL-010 teaches students the basics of combinational digital logic design, which is the foundation of Some of the logic circuits that can be implemented with this trainer include: microprocessor and microcontroller designs. With the DL-010, all necessary logic components 2-to-4 decoder with and without enable are included and pre-mounted for fast, easy 3-to-8 decoder with and without enable which are used as the building blocks of implementation of combinational logic circuits, microprocessors. These circuits include 2-to-1 multiplexer 4-to-1 multiplexer 8-to-1 multiplexer Full adder 4-bit adder 4-bit adder/subtractor 4-bit carry-look-ahead 2-bit ALU 8-to-3 Encoder Comparator Shifter 4-bit BCD to 7-segment decoder Any custom combinational circuit as derived from a truth table with up to four inputs Many custom combinational circuits with more than four Features: 72-page professionally written lab manual authored by university professor, Enoch Hwang, PhD. 11 hands-on labs correlated to an introductory digital logic course. Sturdy blow molded carrying case making the entire lab lightweight and portable. Attractive and easy to use system draws students in to the beauty of digital logic and embedded systems design. multiplexers, decoders, encoders, full adders, adders/subtractors, comparators, and ALU's. Global Specialties' logic trainer simplifies the teaching process by eliminating the need to discretely wire IC's as all gate elements are premounted, de-coupled and de-bounced, ready for immediate classroom use. Students can spend their time directly on logic training. Complete kit with 9V wall adapter and 100 machined pin hookup wires. No need to buy anything else. Most importantly, the trainer includes a 72-page All gate elements are pre-mounted and fully integrated. an overview of digital logic and 11 hands-on labs Expandable breadboard allows the system to grow as students' knowledge increases. professionally written training manual featuring enhancing any textbook currently in use. Perform experiments using standard TTL logic. The DL-010 is a complete and ruggedly packed Well regulated 5V power (Vcc) and ground (GND) points. to individuals and classroom students. trainer that will provide a solid learning platform Each gate element is presented in its easy to visualize graphic form. inputs Innovative Training Solutions globalspecialties.com Analog & DL-010 Digital Design Workstation Embedded Systems Design Series Digital Logic Trainers Training Manual Specifications Combinational Logic Trainer Chapter 1: Combinational Logic Design Trainer Model DL-010 Model DL-010 Not gate 12 2-Input AND gate 12 4-Input AND gate 8 2-Input OR gate 8 4-Input OR gate 8 2-Input XOR gate 12 LEDs 8 7-Segment LED display 1 Slide switch 8 Push Button switch 1 270 tie point Bread Board yes Vcc & GND tie points yes Hook up wire, 100pcs yes 9V wall adaptor yes Regulated 5V supply yes DL-010 Manual yes Width 13.5 in Length 8.5 in Height 3.5 in Weight 3.40 lbs Chapter 2: Microprocessors Introduction to Microprocessors Combinational and Sequential Circuit Analogy Chapter 3: Digital Logic Circuits Basic Logic Gates Digital Circuits Identifying Combinational Circuits Analysis of Combinational Circuits Boolean Algebra Simplifying Combinational Circuits Synthesis of Combinational Circuits Chapter 4: Labs Basic Gates, Lights and Action! NAND, NOR, XOR, AND XNOR Gates Designing Combinational Circuits Multiplexers Decoders Comparators Full Adder 4-bit Adder 4-bit Adder/Subtractor 2-bit Arithmetic and Logic Unit (ALU) BCD to 7-Segment LED Decoder Technical data subject to change without notice Innovative Training Solutions (c)2012 Global Specialties globalspecialties.com 22820 Savi Ranch Parkway Yorba Linda, CA 92887 1-800-572-1028