PRODUCT SELECTION GUIDE
2009
www.yageo.com
SMD RESISTORS + MLCC
SMD CERAMIC EMI FILTER CAPACITORS - X2Y
®
HIGH FREQUENCY PRODUCTS
MULTILAYER CHIP VARISTORS
2
3
Part numbering system and ordering
You can order components from this catalogue in two ways. Both ways give logistic and packing information.
Clear text ordering code
This unique number is an easily-readable code.
- 15 digits code (PHYCOMP CTC )
-14 to 17 digits code (GLOBAL PART NUMBER for both Yageo and Phycomp branded products)
12 digits ordering code
This unique 12NC number forms the basis of the Phycomp logistic system.
Please note that 12 digits ordering code will expire at the end of 2010.
You will nd details for ordering in the "Ordering" section next to each selection chart.
Minimum shipment quantities, prices and delivering details can be obtained from the Yageo sales organization in
your country or from one of our franchised distributors.
Case size codes
Throughout this catalogue, inch-based codes are used
for the component sizes. According to IEC 60384-10,
amendment 2 of September 2000 for MLCCs, and IEC
60115-8, amendment 1 of July 2000 for R-chip. Values
for length and width should be in millimeters rather than
in inches. To distinguish between inch-based codes and
metric-based codes, metric-based codes will temporarily
have the suffix ‘’M’’. The table right next shows the
relation between inch-based case sizes versus the
recommended metric case size designators. Please note
that HF products use metric case size only.
Contact us
Founded in 1977, the Yageo Corporation has become a world-class provider of passive-component services with
capabilities on a global scale, including production and sales facilities in Asia, Europe and America. The corporation
is uniquely positioned to provide one-stop-shopping, offering its complete product portfolio of resistors, capacitors
and inductors in both commodity and specialty versions, plus design-in capability, distribution, e-commerce
connection and logistics. Yageo markets its products under the product brand names Yageo, Phycomp and Vitrohm.
All products can be obtained from our Yageo sales ofces, of which contact details can be found on the backcover of
this catalogue. For most up-to-date information, as well as contact details of our franchise distributors, please refer
to our website: www.yageo.com
•
•
Case size designation and cross-reference
Inch-based Metric Inch-based Metric Inch-based Metric
01005 0402M 0606 1616M 1224 3250M
0201 0603M 0612 1632M 1225 3264M
0202 0605M 0616 1640M 1812 4532M
0402 1005M 0805 2012M 2007 5320M
0404 1010M 1008 2520M 2010 5025M
0408 1020M 1206 3216M 2220 5750M
0508 1220M 1210 3225M 2512 6432M
0603 1608M 1218 3245M 3014 7836M
Preface
4
Resistor Chip General Information 8
Specification overview 8
Ordering Information - Global part number 10
Ordering information for North America 12
IEC publication 63, SPQ, last digit of 12NC 13
Resistor Chip Selection Charts 14
Thick film resistor chips 14
Introduction to thick film genaral purpose and double power resistors 14
01005 to 0805 16
1206 to 2512 18
Thin film resistor chips 20
Introduction to thin film chip resistors 20
High precision - High stability, 0402 / 0603 22
High precision - High stability, 0805 to 1210 24
High precision - High stability, 2010 / 2512 26
General Purpose, 0402 to 2512 28
Thick film Array / Network resistor chips 30
Introduction to thick film array / network resistors 30
Arrays, convex and concave 32
Networks, T-type and L-type 34
Thin film Array / Multi-value resistor chips (convex type) 36
Introduction to thin film array chip resistors 36
Low ohmic resistor chips 38
Introduction to low ohmic / low ohmic high power chip resistors 38
Low ohmic, 0201 to 1206 40
Low ohmic, 1210 to 2512 42
Low ohmic, high power, 0805 / 1206 44
High ohmic resistor chips 46
Introduction to high ohmic chip resistors 46
Resistor chips with Ni/Au terminations 48
Introduction to Ni/Au terminations chip resistors 48
0402 to 1206 50
Surge resistor chips 52
Introduction to Surge chip resistors 52
0805 to 2512 54
High voltage resistor chips 56
Introduction to high voltage chip resistors 56
0805 to 2512 58
Trimmable resistor chips 60
Introduction to trimmable chip resistors 60
0402 to 1206 62
Current sensors - Low TCR resistor chips (standard / power enhancement) 64
Introduction to current sensors - low TCR chip resistors 64
Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512 66
RF attenuators chip resistors 68
Introduction to RF attenuator chip resistors 68
0404 70
Resistor Chip Engineering Design Kits 71
Engineering design kits 71
Table of Contents
5
MLCC General Information 74
Specification overview 74
Case dimensions 75
Ordering Information - Global part number 76
Ordering information for North America 77
Thickness classes and packing quantities for all series 78
MLCC Selection Charts 79
NP0 79
NP0 - General purpose 16 to 25V, 0201 to 0603 79
NP0 - General purpose 16 to 25V, 0805 to 1210 80
NP0 - Gerneral purpose 50V, 0201 to 1812 82
NP0 - Midium voltage, 0603 / 0805 85
NP0 - Midium voltage, 1206 / 1210 86
NP0 - Midium voltage, 1808 / 1812 87
NP0 - High voltage, 1206 / 1210 88
NP0 - High voltage, 1808 / 1812 89
NP0 - High frequency, 0402 / 0603 91
NP0 - Microwave, 0603 to 1206 93
X7R 95
X7R - General purpose, 0201 / 0402 95
X7R - General purpose & High capacitance, 0603 / 0805 96
X7R - Gerneral purpose & High capacitance, 1206 to 1812 97
X7R - Midium voltage, 0603 / 0805 98
X7R - Midium voltage, 1206 / 1210 99
X7R - Midium voltage, 1808 / 1812 100
X7R - High voltage, 1206 / 1210 101
X7R - High voltage, 1808 / 1812 102
X7R - Low inductance, 0306 to 0612 104
X5R 106
X5R - General purpose & High capacitance, 0201 / 0402 106
X5R - General purpose & High capacitance, 0603 / 0805 107
X5R - High capacitance, 1206 to 1812 108
Y5V 110
Y5V - General purpose & High capacitance, 0201 / 0402 110
Y5V - General purpose & High capacitance, 0603 / 0805 111
Y5V - General purpose & High capacitance, 1206 / 1210 112
Safety certification MLCCs 114
NP0 - High voltage SC type, 1808 / 1812 114
X7R - High voltage SC type, 1808 / 1812 115
Arrays 117
X7R - 2C Arrays, 0405 117
NP0 - 4C Arrays, 0508 / 0612 119
X7R - 4C Arrays, 0508 / 0612 120
Y5V - 4C Arrays, 0508 / 0612 121
MLCC Engineering Design Kits 123
Sample kits for 0201 / 0402 123
Sample kits for 0603 / 0805 124
Sample kits for 1206 125
Sample kits for high capacitance series 126
Table of Contents
6
High voltage sample kits for PCs segment 127
High voltage sample kits for inverter segment 128
High voltage sample kits for general application 129
High voltage sample kits for safety certification MLCCs 130
Sample kits for high frequency series 131
Sample kits for all sizes, all types, E1 series only 132
HF Product Selection Charts 134
GPS patch antenna and active module 134
UHF, Dual-band and Triple-band antenna 135
Bluetooth antenna 136
Band pass filter and Low pass filter 137
Balun and Combo 138
Diplexer 139
X2Y® Product Selection Charts 142
SMD Ceramic EMI Filter Capacitors X2Y® series 142
Ordering information 143
MLV Product Selection Charts 146
Case dimensions and specification for 0402 146
Specification for 0603 to 1206 147
Ordering information for 0402 to 1206 148
Table of Contents
SURFACE-MOUNT RESISTOR CHIPS
8
T. C. R. - RL series
Type Operating
Temp. range Resistance
range T. C. R.
50mΩ - 1Ω
RL0402 -55°C to +125°C 50mΩ≤R<1Ω ±800 ppm/°C
10mΩ - 36mΩ 36mΩ - 91mΩ 91mΩ - 500mΩ 500mΩ - 1Ω
RL0603 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±800 ppm/°C ±300 ppm/°C
10mΩ - 18mΩ 20mΩ - 47mΩ 51mΩ - 91mΩ 100mΩ - 360mΩ 390mΩ - 500mΩ 510mΩ - 1Ω
RL0805 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL1206 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL1210 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 000 ppm/°C ±800 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
10mΩ - 30mΩ 33mΩ - 56mΩ 60mΩ - 180mΩ 200mΩ - 1Ω
RL1218 -55°C to +125°C 10mΩ≤R<1Ω ±2 000 ppm/°C ±1 000 ppm/°C ±700 ppm/°C ±250 ppm/°C
10mΩ - 18mΩ 20mΩ - 47mΩ 51mΩ - 91mΩ 100mΩ - 360mΩ 390mΩ - 500mΩ 510mΩ - 1Ω
RL2010 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL2512 -55°C to +125°C 10mΩ ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±800 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
Global part number Series Size Power
rating Max.
voltage Operating
Temp. range Resistance
range Tolerance T. C. R.
!
RC0100xR-07xxxxL
RC
01005 1/32W 15V -55°C to 125°C 10Ω≤ R ≤1MΩ ±5% 10Ω≤ R ≤1MΩ ±250 ppm/°C
RC0201xR-07xxxxL 0201 1/20W 25V -55°C to 125°C 1Ω≤ R ≤10MΩ Max.: 1MΩ ±1%
Max.: 10MΩ ±5%
1Ω≤ R ≤10Ω
10Ω< R ≤10MΩ -100/+350 ppm/°C
±200 ppm/°C
RC0402xR-07xxxxL 0402 1/16W 50V -55°C to 155°C 1Ω≤ R ≤22MΩ
Max./Min.: 1MΩ/10Ω ±0.5%
Max.: 10MΩ ±1%
Max.: 22MΩ ±5%
1Ω≤ R ≤10Ω
10MΩ< R ≤22MΩ ±200 ppm/°C
RC0603xR-07xxxxL 0603 1/10W 50V -55°C to 155°C 1Ω≤ R ≤22MΩ
RC0805xR-07xxxxL 0805 1/8W 150V -55°C to 155°C 1Ω≤ R ≤22MΩ
RC1206xR-07xxxxL 1206 1/4W 200V -55°C to 155°C 1Ω≤ R ≤22MΩ
RC1210xR-07xxxxL 1210 1/2W 200V -55°C to 155°C 1Ω≤ R ≤22MΩ 10Ω< R ≤10MΩ ±100 ppm/°C
RC1218xK-07xxxxL 1218 1W 200V -55°C to 155°C 1Ω≤ R ≤1MΩ
RC2010xK-07xxxxL 2010 3/4W 200V -55°C to 155°C 1Ω≤ R ≤22MΩ
RC2512xK-07xxxxL 2512 1W 200V -55°C to 155°C 1Ω≤ R ≤22MΩ
!
RC0805xR-7WxxxxL 0805 1/4W 150V -55°C to 155°C 1Ω≤ R ≤100Ω ±1%
±5% ±200 ppm/°C
!
RC1206xR-7WxxxxL 1206 1/2W 200V -55°C to 155°C 1Ω≤ R ≤100Ω
!
RC2512xK-7WxxxxL 2512 2W 200V -55°C to 155°C 1Ω≤ R ≤150Ω
!
RC0805xR-07xxxxL 0805 1/8W 150V -55°C to 155°C 24MΩ≤ R ≤100MΩ ±5%, ±10%, ±20% ±300 ppm/°C
!
RC1206xR-07xxxxL 1206 1/4W 200V -55°C to 155°C 24MΩ≤ R ≤100MΩ
!
YC102-xR-07xxxxL
YC
2*0201 1/32W 15V -55°C to 125°C 10Ω≤ R ≤1MΩ Min.: 10Ω ±1%
Min.: 1Ω ±5%
±200 ppm/°C
YC122-xR-07xxxxL 2*0402 1/16W 50V -55°C to 125°C 1Ω≤ R ≤1MΩ
YC124-xR-07xxxxL 4*0402 1/16W 50V -55°C to 155°C 10Ω≤ R ≤1MΩ
!
YC162-xR-07xxxxL 2*0603 1/16W 50V -55°C to 155°C 10Ω≤ R ≤1MΩ ±5%
YC164-xR-07xxxxL 4*0603 1/16W 50V -55°C to 155°C 1Ω≤ R ≤1MΩ ±1%
±5%
YC248-xR-07xxxxL 8*0602 1/16W 50V -55°C to 155°C 10Ω≤ R ≤1MΩ
YC324-xR-07xxxxL 4*1206 1/8W 200V -55°C to 155°C 10Ω≤ R ≤1MΩ
!
TC122-xR-07xxxxL TC 2*0402 1/16W 25V -55°C to 125°C 10Ω≤ R ≤1MΩ Min.: 10Ω ±1%
Min.: 1Ω ±5%
!
TC124-xR-07xxxxL 4*0402 1/16W 50V -55°C to 125°C 10Ω≤ R ≤1MΩ
TC164-xR-07xxxxL 4*0603 1/16W 50V -55°C to 155°C 1Ω≤ R ≤1MΩ
YC158TJR-07xxxxL YC158 10P8R
(0612) 1/16W 25V -55°C to 155°C 10Ω≤ R ≤100KΩ ±5% 10Ω≤ R ≤100KΩ ±200 ppm/°C
YC358xJK-07xxxxL YC358 10P8R
(1225) 1/16W 50V -55°C to 155°C 10Ω≤ R ≤330KΩ ±5% 10Ω≤ R ≤330KΩ ±200 ppm/°C
RL0402xR-07xxxxL
RL
0402 1/16W (PxR)^1/2 -55°C to 125°C 0.05Ω≤ R <1Ω
±1%
±2%
±5% See following table
“T.C.R.- RL series“
RL0603xR-07xxxxL 0603 1/10W (PxR)^1/2 -55°C to 125°C
0.01Ω≤ R <1Ω
RL0805xR-07xxxxL 0805 1/8W (PxR)^1/2 -55°C to 125°C
RL1206xR-07xxxxL 1206 1/4W (PxR)^1/2 -55°C to 125°C
RL1210xR-07xxxxL 1210 1/2W (PxR)^1/2 -55°C to 125°C
RL1218xK-07xxxxL 1218 1W (PxR)^1/2 -55°C to 125°C
RL2010xK-07xxxxL 2010 3/4W (PxR)^1/2 -55°C to 125°C
RL2512xK-07xxxxL 2512 1W (PxR)^1/2 -55°C to 125°C
!
RL0805xR-7WxxxxL 0805 1/4W (PxR)^1/2 -55°C to 125°C 0.01Ω≤ R <1Ω
!
RL1206xR-7WxxxxL 1206 1/2W (PxR)^1/2 -55°C to 125°C
Note: " ! " is the symbol for new product
Resistor Chip General Information
Specification overview
9
Global part number Series Size Power
rating Max.
voltage Operating
Temp. range Resistance
range Tolerance T. C. R.
RT0402xRx07xxxxL
RT
0402 1/16W 50V
-55°C to 125°C
10Ω≤ R <121KΩ
±0.05%
±0.1%
±0.25%
±0.5%
±1%
±10 ppm/°C
±15 ppm/°C
±25 ppm/°C
±50 ppm/°C
RT0603xRx07xxxxL 0603 1/10W 75V 5.1Ω≤ R ≤681KΩ
RT0805xRx07xxxxL 0805 1/8W 150V 5.1Ω≤ R ≤1.5MΩ
RT1206xRx07xxxxL 1206 1/8W
200V
5.1Ω≤ R ≤1.5MΩ
RT1210xRx07xxxxL 1210 1/4W 5.1Ω≤ R ≤1MΩ
RT2010xKx07xxxxL 2010 1/2W 10Ω≤ R ≤1MΩ
RT2512xKx07xxxxL 2512 3/4W 10Ω≤ R ≤1MΩ
RJ0402FRE07xxxxL
RJ
0402 1/16W 25V
-55°C to 125°C
10Ω≤ R ≤121KΩ
±1% ±50 ppm/°C
RJ0603FRE07xxxxL 0603 1/16W 50V 5.1Ω≤ R ≤681KΩ
RJ0805FRE07xxxxL 0805 1/10W 100V 5.1Ω≤ R ≤1.5MΩ
RJ1206FRE07xxxxL 1206 1/8W
150V
5.1Ω≤ R ≤1.5MΩ
RJ1210FRE07xxxxL 1210 1/4W 5.1Ω≤ R ≤1MΩ
RJ2010FKE07xxxxL 2010 1/2W 10Ω≤ R ≤1MΩ
RJ2512FKE07xxxxL 2512 3/4W 10Ω≤ R ≤1MΩ
!
TA164-xR-07xxxxL TA 4*0603 1/16W 75V -55°C to 125°C 10Ω≤ R ≤330KΩ ±0.1%
±0.5%
±1% ±25 ppm/°C
±50 ppm/°C
!
TD164-xR-07xxxxL TD 4*0603 1/16W 75V -55°C to 125°C 10Ω≤ R ≤330KΩ ±0.1%
±0.5%
±1% ±25 ppm/°C
±50 ppm/°C
PR2010xKx07xxxxxL
PR 2010 0.5W
(PxR)^1/2 -55°C to 155°C 2mΩ≤ R ≤6mΩ ±1%
±2%
±5%
2mΩ≤ R ≤6mΩ ±150 ppm/°C
PR2010xKx7WxxxxxL 1W
PR2512xKx07xxxxxL 2512 1W 1mΩ≤ R ≤5mΩ 1mΩ≤ R ≤2mΩ ±200 ppm/°C
PR2512xKx7WxxxxxL 2W 2mR <R ±100 ppm/°C
PF2512xKx07xxxxxL PF 2512 1W (PxR)^1/2 -55°C to 155°C 6mΩ≤ R ≤130mΩ ±1%
±2%
±5% ±100 ppm/°C
PF2512xKx7WxxxxxL 2512 2W 6mΩ≤ R ≤130mΩ
!
PT0402xRx07xxxxL
PT
0402 1/16W
(PxR)^1/2
-55°C to 125°C
100mΩ≤ R ≤910mΩ ±1%
±5%
±200 ppm/°C
!
PT0603xRx07xxxxL 0603 1/10W
!
PT0805xRx07xxxxL 0805 1/8W
!
PT1206xRx07xxxxL 1206 1/4W
±100 ppm/°C
!
PT1210xRx07xxxxL 1210 1/2W
!
PT1218xKx07xxxxL 1218 1W -55°C to 155°C
!
PT2010xKx07xxxxL 2010 3/4W -55°C to 125°C
!
PT2512xKx07xxxxL 2512 1W -55°C to 155°C
AR0402xR-07xxxxL
AR
0402 1/16W 50V -55°C to 155°C 1Ω≤ R ≤10MΩ ±1%
±5% 1Ω≤ R ≤10Ω
10Ω< R ≤10MΩ ±200 ppm/°C
±100 ppm/°C
AR0603xR-07xxxxL 0603 1/10W
AR0805xR-07xxxxL 0805 1/8W 150V
AR1206xR-07xxxxL 1206 1/4W 200V
RV0805JR-07xxxxL
RV
0805 1/8W 400V -55°C to 155°C 100KΩ≤ R ≤10MΩ ±1%
±5% 100KΩ≤ R ≤10MΩ ±200 ppm/°C
RV1206JR-07xxxxL 1206 1/4W 500V -55°C to 155°C 100KΩ≤ R ≤27MΩ ±5% 100KΩ≤ R ≤27MΩ ±200 ppm/°C
RV1206FR-07xxxxL 100KΩ≤ R ≤10MΩ ±1%
RV2512JK-07xxxxL 2512 1W -55°C to 155°C 4.7MΩ≤ R ≤16MΩ ±5% 4.7MΩ≤ R ≤16MΩ ±200 ppm/°C
SR0805xR-07xxxxL
SR
0805 1/8W 150V
-55°C to 155°C
1Ω≤ R ≤100KΩ ±5%
±10%
±20% 1Ω≤ R ≤100KΩ ±200 ppm/°C
SR1206xR-07xxxxL 1206 1/4W 200V 1Ω≤ R ≤100KΩ
SR1218xK-07xxxxL 1218 1W 1Ω≤ R ≤100KΩ
SR2512xK-07xxxxL 2512 1W 1Ω≤ R ≤100KΩ
TR0402xR-07xxxxL
TR
0402 1/16W 50V -55°C to 125°C
1Ω≤ R ≤10MΩ +0/-10%
+0/-20%
+0/-30%
1Ω≤ R ≤10Ω ±200 ppm/°C
TR0603xR-07xxxxL 0603 1/16W 1MΩ< R ≤10MΩ
TR0805xR-07xxxxL 0805 1/8W 150V -55°C to 155°C 10Ω< R ≤1MΩ ±100 ppm/°C
TR1206xR-07xxxxL 1206 1/4W 200V
ATV321xR-07xxxxL AT 0404 40mW 50V -55°C to 125°C 1DB to 20D B ±0.3dB
±0.5dB
±1.0dB
±2.0dB ---
Note: " ! " is the symbol for new product
Resistor Chip General Information
Specification overview
10
Global part number - Single resistor (3)
R C 0 6 03 J R ―0 7 1 0 R ( L )
Series name (code 1-2) Optional code (1/2) (code 17)
RC = General purpose thick lm
RT = High precision - High stability thick lm Resistance (code 12-16)
RJ = General purpose thin lm 0R = Jumper
RL = Low ohmic 0R1 = 0.1Ω
PR / PF / PT = Current sensor - low TCR 1R = 1Ω
TR = Trimmable 10R = 10Ω
SR = Surge 100R = 100Ω
AR = NiAu termination 1K = 1 000Ω
RV = High voltage 1M = 1 000 000Ω
AT = RF attenuator thick lm 100M = 1 000 000 000Ω
Size code (code 3-6) Taping reel (code 10-11)
(inch / metric) 07 = 7 inch Dia. reel
0100 = 0.4 x 0.2 10 = 10 inch Dia. reel
0201 = 0.6 x 0.3 13 = 13 inch Dia. reel
0402 = 1.0 x 0.5
0603 = 1.6 x 0.8 T. C. R. (code 9)
0805 = 2.0 x 1.25 B = ±10 ppm/°C (on request)
1206 = 3.2 x 1.6 C = ±15 ppm/°C (on request)
1210 = 3.2 x 2.6 D = ±25 ppm/°C
1218 = 3.2 x 4.5 E = ±50 ppm/°C
2010 = 5.0 x 2.5 M = ±75 ppm/°C
2512 = 6.35 x 3.2 F = ±100 ppm/°C
L = ±150 ppm/°C
Tolerance (code 7) G = ±200 ppm/°C
W = ±0.05% “―” = Based on spec.
B = ±0.1% (― for thick lm only)
C = ±0.25%
D = ±0.5% Packing style (code 8 )
F = ±1% R = Paper tape reel
G = ±2% K = Embossed plastic tape reel
J = ±5% (for Jumper ordering) C = Bulk cassette
K = ±10% (for TR = 0/-10%)
M = ±20% (for TR = 0/-20%)
N = ±30% (for TR = 0/-30%)
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
3. Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
Resistor Chip General Information
Ordering Information - Global part number
11
Global part number - Power enhancement
R L 0 8 0 5 J R ―7 W 0 R 0 1 5 ( L )
Series name (code 1-2) Optional code (code 17)
RC = General purpose thick lm
RL = Low ohmic Resistance (code 12-16)
PR / PF / PT = Current sensor - low TCR 0R01 = 0.01Ω
0R1 = 0.1Ω
Size code (code 3-6) 1R = 1Ω
(inch / metric) 10R = 10Ω
0805 = 2.0 x 1.25 100R = 100Ω
1206 = 3.2 x 1.6 1K = 1 000Ω
2010 = 5.0 x 2.5 1M = 1 000 000Ω
2512 = 6.35 x 3.2 Power rating (code 11)
Tolerance (code 7) W = 2 x standard power
F = ±1%
G = ±2% Taping reel (code 10)
J = ±5% 7 = 7 inch Dia. reel
Packing style (code 8 ) T. C. R. (code 9)
R = Paper tape reel M = ±75 ppm/°C
K = Embossed plastic tape reel F = ±100 ppm/°C
G = ±200 ppm/°C
“―” = Based on spec.
(― for thick lm only)
Global part number - Arrays & Networks
Y C 1 6 4 ―J R ―0 7 1 0 R ( L )
Series name (code 1-2) Optional code (code 17)
YC = Aarray & Network (convex) thick lm
TC = Array (concave) thick lm Resistance (code 12-16)
TA = Array (convex) thin lm 0R = Jumper
TD = Multi value array (convex) thin lm 0R1 = 0.1Ω
1R = 1Ω
Size code (inch) (code 3-4) 10R = 10Ω
10 = 0201 x 2 (0202) 100R = 100Ω
12 = 0402 x 2 (0404) 1K = 1 000Ω
0402 x 4 (0408) 1M = 1 000 000Ω
15 = 10Pin/8R (0612)
16 = 0603 x 2 (0606) Taping reel (code 10-11)
0603 x 4 (0612) 07 = 7 inch Dia. reel
24 = 0602 x 8 (0616) 10 = 10 inch Dia. reel
32 = 1206 x 4 (1224) 13 = 13 inch Dia. reel
35 = 10Pin/8R (1225) T.C.R. (code 9)
Number of resistors (code 5) D = ±25 ppm/°C
2 = 2 resistors E = ±50 ppm/°C
4 = 4 resistors "―" = Based on spec.
8 = 8 resistors Packing style (code 8 )
Schematic (code 6) R = Paper tape reel
L = L-type (for YC358) K = Embossed plastic tape reel
T = T-type (for YC158/358)
“―” = Based on spec. Tolerance (code 7)
B = ±0.1%
D = ±0.5%
F = ±1%
J = ±5% (for Jumper ordering)
Resistor Chip General Information
Ordering Information - Global part number
12
Phycomp CTC ordering code - Noth America
Ordering example: 9C06031A10R0FKHFT = R-chip 0603, 10R0, 1%, 5K reel
1-2 3-6 7-8 9-12 13 14 15-16 17
X X X X X X X X X X X X X X X X X
Series name (code 1-2) Packing style (code 17 )
9C = Phycomp Thick lm chip resistors T = 5K paper
9T = Phycomp Thin lm chip resistors 3 = 10K paper
4 = 20K paper
Size code (standard resistors, code 3-6) 5 = 4K blister
0201 0201 (0603) 6 = 5K blister
0402 0402 (1005) 7 = 50K paper
0603 0603 (1608) P = 25K bulk case
0805 0805 (2012)
1206 1206 (3216) Special coding (code 15-16)
1210 1210 (3225) HF = SnPb
1218 1218 (3248) PF = Lead free
2010 2010 (5025) AF = NiAu
2512 2512 (6432)
AC34 0603 (1608) 4R concave array T.C.R. (code 14)
AV34 0603 (1608) 4R convex array C = ±10 ppm/°C
AV22 0402 (1005) 2R convex array D = ±15 ppm/°C
AV24 0402 (1005) 4R convex array A = ±25 ppm/°C
AV28 0402 (1005) 8R convex array B = ±50 ppm/°C
RN31 10P8R in 1206 convex network K = ±100 ppm/°C
FR01 1206 (3216) Fusible L = ±200 ppm/°C
FR21 0603 (1608) Fusible E = ±250 ppm/°C
SR01 1206 (3216) Surge M = ±300 ppm/°C
VR01 1206 (3216) High voltage 5% G = ±500 ppm/°C
VR02 1206 (3216) High voltage 1% F = 0/+500 ppm/°C
VR11 0805 (2012) High voltage 5% R = ±600 ppm/°C
VR12 0805 (2012) High voltage 1% Q = -100/+600 ppm/°C
VR21 2512 (6432) High voltage 5% P = ±750 ppm/°C
MR22 2512 (6432) Current sensor - low TCR H = ±1000 ppm/°C
MF22 2512 (6432) Current sensor - low TCR I = ±1500 ppm/°C
V321 0404 (1010) RF attenuator J = ±2000 ppm/°C
N = ±3000 ppm/°C
Power rating (code 7-8)
1A 1/16W 0.063W 90402 Tolerance (code 13)
1A 1/10W 0.10W (0603 E = ±0.01%
2A 1/8W 0.125W (0805) A = ±0.05%
3A 1/4W 0.25W (1206) B = ±0.1%; 0.2dB
5A 1/2W 0.5W (1210) C = ±0.25%; 0.3dB
7A 1/20W 0.05W (0201) D = ±0.5%; 0.5dB
8A 1/32W 0.03125W (RN31) F = ±1%; 1dB
12 3/4W 0.75W (2010) G = ±2%; 2dB
1W 1W 1W (1218/2512) J = ±5%
2W 2W 2W N = 0/-20%
R = 0/-30%
Resistance valre (code 9-12)
0R00 = Jumper
R0XX < 0.1Ω
RXXX = 0.1Ω - 0.976Ω
XRXX = 1Ω - 9.76Ω
XXRX = 10Ω - 97.6Ω
XXX0 = 100Ω - 976Ω
XXX1 = 1K - 9.76K
XXX2 = 10K - 97.6K
XXX3 = 100K - 9.78K
XXX4 = 1M - 9.76M
XXX5 = 10M - 97.6M
XXX6 = 100M+
XXDB = 1 - 20DB
Right values apply to
trimmable resistors
dB values apply to
Attenuators
Resistor Chip General Information
Ordering information for North America
13
Standard of values in a decade according to “IEC publication 63”
E6 series 10 15 22 33 47 68
E12 series 10 12 15 18 22 27 33 39 47 56 68 82
E24 series 10 11 12 13 15 16 18 20 22 24 27 30
33 36 39 43 47 51 56 62 68 75 82 91
E96 series 100 102 105 107 110 113 115 118 121 124 127 130
133 137 140 143 147 150 154 158 162 165 169 174
178 182 187 191 196 200 205 210 215 221 226 232
237 243 249 255 261 267 274 280 287 294 301 309
316 324 332 340 348 357 365 374 383 392 402 412
422 432 442 453 464 475 487 499 511 523 536 549
562 576 590 604 619 634 649 665 681 698 715 732
750 768 787 806 825 845 866 887 909 931 953 976
Packing quantities
Size code Tape width 178mm / Ø7” reel 254mm / Ø10" reel 330mm / Ø13" reel Mass per 100 units Volume
Paper Embossed Paper Paper Embossed Mass (g) mm3
0100 8mm 10 000 --- --- --- --- 0.007 0.0104
0201 8mm 10 000 --- 20 000 50 000 --- 0.016 0.041
0402 8mm 10 000 --- 20 000 50 000 --- 0.058 0.175
0603 8mm 5 000 --- 10 000 20 000 --- 0.192 0.576
0805 8mm 5 000 --- 10 000 20 000 --- 0.450 1.250
1206 8mm 5 000 --- 10 000 20 000 --- 0.862 2.728
1210 8mm 5 000 --- 10 000 20 000 --- 1.471 4.030
1218 12mm --- 4 000 --- --- --- 2.703 7.590
2010 12mm --- 4 000 --- --- 16 000 2.273 6.875
2512 12mm --- 4 000 --- --- --- 3.704 10.827
YC102 8mm 10 000 --- --- --- --- 0.052 ---
YC122 8mm 10 000 --- --- 50 000 --- 0.100 ---
TC122 8mm 10 000 --- --- 50 000 --- 0.112 ---
ATV321 8mm 10 000 -- --- --- --- 0.100 ---
YC124 8mm 10 000 --- 20 000 40 000 --- 0.281 ---
TC124 8mm 10 000 --- 20 000 40 000 --- 0.311 ---
YC162 8mm 5 000 --- -- --- --- 0.376 ---
YC164 8mm 5 000 --- 10 000 20 000 --- 0.833 ---
TC164 8mm 5 000 --- 10 000 20 000 --- 1.030 ---
YC158 8mm 5 000 --- --- 20 000 --- 0.855 ---
YC248 12mm 5 000 4 000 --- --- --- 0.885 ---
YC324 12mm --- 4 000 --- --- --- 2.703 ---
YC358 12mm --- 4 000 --- --- --- 3.333 ---
12NC Ordering information
The rst 8 or 9 digits of the 12 digit catalogue number are given under section
“Phycomp world wide - Traditional type” on following pages.
The remaining 4 or 3 digits represent the resistance value with the last digit
indicating the multiplier as shown in right table.
Last digit of 12NC
Resistance Last digit
0.001 to 0.0976 Ω 0
0.1 to 0.976 Ω 7
Example:
0.001 Ω = 0010 or 010
0.02 Ω = 0200 or 200
0.3 Ω = 3007 or 307
1 Ω = 1008 or 108
33 kΩ = 3303 or 333
10 MΩ = 1006 or 106
1 to 9.76 Ω 8
10 to 97.6 Ω 9
100 to 976 Ω 1
1 to 9.76 kΩ 2
10 to 97.6 kΩ 3
100 to 976 kΩ 4
1 to 9.76 MΩ 5
10 to 97.6 MΩ 6
Resistor Chip General Information
IEC publication 63, SPQ, last digit of 12NC
14
Features
Extremely thin and light
Hightly reliable multilayer electrode construction
Compatible with all soldering process
Highly stable in auto-placement surface mounting applications
Barrier layer end termination
Zero ohm jumper is available
Available in 8mm tape & reel per EIA RS481
•
•
•
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
RC0402-
RC2512
125
RC0100-
RC0201
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
(Jumper chip is a conductor)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
RC0100 0.40 ±0.03 0.20 ±0.03 0.13 ±0.03 0.10 ±0.03 0.10 ±0.03
RC0201 0.60 ±0.03 0.30 ±0.03 0.23 ±0.03 0.10 ±0.05 0.15 ±0.05
RC0402 1.00 ±0.05 0.50 ±0.05 0.32 ±0.05 0.20 ±0.10 0.25 ±0.10
RC0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
RC0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
RC1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
RC1210 3.10 ±0.10 2.60 ±0.15 0.50 ±0.10 0.45 ±0.15 0.50 ±0.20
RC1218 3.10 ±0.10 4.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
RC2010 5.00 ±0.10 2.50 ±0.15 0.55 ±0.10 0.55 ±0.15 0.50 ±0.20
RC2512 6.35 ±0.10 3.10 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Resistor Chip Selection Charts
Introduction to thick film genaral purpose and double power resistors
15
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C) Jumper criteria
(unit: A)
RC0100 1/32W -55°C to +125°C 15V 30V 30V E24 ±5%
Zero ohm jumper 10Ω - 1MΩ
< 0.05Ω 10Ω ≤ R ≤ 1MΩ ±250 Rated current
Max. current 0.5
1.0
RC0201 1/20W -55°C to +125°C 25V 50V 50V E24 ±5%
E24/E96 ±1%
E24/E96 ±0.5%
Zero ohm jumper
1Ω - 10MΩ
1Ω - 1MΩ
10Ω - 1MΩ
< 0.05Ω
10Ω < R ≤ 10MΩ
1Ω ≤ R ≤ 10Ω ±200
-100/+350 Rated current
Max. current 0.5
1.0
RC0402 1/16W -55°C to +155°C 50V 100V 100V
E24 ±5%
E24/E96 ±1%
E24/E96 ±0.5%
Zero ohm jumper
1Ω - 22MΩ
1Ω - 10MΩ
10Ω - 1MΩ
< 0.05Ω
10Ω < R ≤ 10MΩ
1Ω ≤ R ≤ 10Ω
10MΩ < R ≤ 22MΩ
±100
±200
Rated current
Max. current 1.0
2.0
RC0603 1/10W -55°C to +155°C 50V 100V 100V Rated current
Max. current 1.0
2.0
RC0805 1/8W -55°C to +155°C 150V 300V 300V Rated current
Max. current 2.0
5.0
RC1206 1/4W -55°C to +155°C 200V 400V 500V Rated current
Max. current 2.0
10.0
RC1210 1/2W -55°C to +155°C 200V 500V 500V Rated current
Max. current 2.0
10.0
RC1218 1W -55°C to +155°C 200V 500V 500V E24 ±5%
E24/E96 ±1%
E24/E96 ±0.5%
Zero ohm jumper
1Ω - 1MΩ
1Ω - 1MΩ
10Ω - 1MΩ
< 0.02Ω
Rated current
Max. current 6.0
10.0
RC2010 3/4W -55°C to +155°C 200V 500V 500V E24 ±5%
E24/E96 ±1%
E24/E96 ±0.5%
Zero ohm jumper
1Ω - 22MΩ
1Ω - 10MΩ
10Ω - 1MΩ
< 0.05Ω
Rated current
Max. current 2.0
10.0
RC2512 1W -55°C to +155°C 200V 500V 500V Rated current
Max. current 2.0
10.0
Double
power
RC0805 1/4W -55°C to +155°C 150V 300V 300V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
1Ω - 100Ω
1Ω - 100Ω
< 0.05Ω
1Ω ≤ R ≤ 100Ω ±200
Rated current
Max. current 2.0
5.0
Double
power
RC1206 1/2W -55°C to +155°C 200V 400V 500V Rated current
Max. current 3.0
7.5
Double
power
RC2512 2W -55°C to +155°C 200V 400V 500V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
1Ω - 150Ω
1Ω - 150Ω
< 0.05Ω
1Ω ≤ R ≤ 150Ω ±200 Rated current
Max. current 6.0
15.0
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required
±(3%+ 0.05Ω) for 01005
±(2%+ 0.05Ω) for others
< 100mΩ for jumper
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered
±(1%+ 0.05Ω)
< 50mΩ for jumper
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at
8 hours (method 106F), 3 cycles / 24 hours
for 10d with 25°C / 65°C 95% R.H
±(3%+ 0.05Ω) for 01005
±(2%+ 0.05Ω) for others
< 100mΩ for jumper
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5%+ 0.05Ω) for 10K to 10M
±(1%+ 0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1%+ 0.05Ω)
< 50mΩ for jumper
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(2%+ 0.05Ω)
< 50mΩ for jumper
Resistor Chip Selection Charts
Introduction to thick film genaral purpose and double power resistors
16
General Purpose thick film / RC series
Size: inch (mm) 0201 (0603) 0402 (1005) 0603 (1608) 0805 (2012)
Power P70 1/20W 1/16W 1/10W 1/8W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1%
Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96
Jumper
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
2.2 MΩ
3.3 MΩ
4.7 MΩ
6.8 MΩ
10 MΩ
15 MΩ
22 MΩ
Remark
Note: Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
01005 to 0805
17
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RC0603JR-07100K(L)
R C 0 6 0 3 J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
RC = General purpose thick lm Resistance (code 12-16)
Size code (code 3-6) 0R = Jumper
(inch / metric) 10R = 10Ω
0100 = 0.4 x 0.2 100R = 100Ω
0201 = 0.6 x 0.3 100K = 100KΩ
0402 = 1.0 x 0.5
0603 = 1.6 x 0.8 Taping reel (code 10-11)
0805 = 2.0 x 1.25 07 = 7 inch Dia. reel
1206 = 3.2 x 1.6 10 = 10 inch Dia. reel
1210 = 3.2 x 2.6 13 = 13 inch Dia. reel
1218 = 3.2 x 4.5
2010 = 5.0 x 2.5 T. C. R. (code 9)
2512 = 6.35 x 3.2 “―” = Based on spec.
(― for thick lm only)
Tolerance (code 7)
D = ±0.5% Packing style (code 8 )
F = ±1% R = Paper tape reel
J = ±5% (for Jumper ordering) K = Embossed plastic tape reel
C = Bulk cassette
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
General purpose thick lm / RC series
Size: inch (mm) 0201 (0603) 0402 (1005) 0603 (1608) 0805 (2012)
Power 1/20 W 1/16 W 1/10 W 1/8 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1%
Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96
Packing paper tape paper tape paper tape paper tape
Quantity 5 000 --- --- --- --- 2322 702 60...L 2322 704 6.…L 2322 730 61...L 2322 734 6.…L
10 000 2322 803 70...L 2322 806 7.…L 2322 705 70...L 2322 706 7.…L 2322 702 70...L 2322 704 7.…L 2322 730 71...L 2322 734 7.…L
20 000 2322 806 80...L 2322 806 8.…L --- --- 2322 702 81...L 2322 704 8.…L 2322 730 81...L 2322 734 8.…L
50 000 2322 803 60...L 2322 806 6.…L 2322 705 87...L 2322 706 8.…L --- --- --- ---
Jumper 5 000 --- --- --- --- 2322 702 96001L --- 2322 730 91002L ---
10 000 2322 803 91001L --- 2322 705 91001L --- 2322 702 97001L --- 2322 730 91003L ---
20 000 --- --- --- --- 2322 702 92002L --- 2322 730 92002L ---
50 000 --- --- 2322 705 91007L --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
01005 to 0805
18
General Purpose thick film / RC series
Size: inch (mm) 1206 (3216) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432)
Power P70 1/4W 1/2W 1W 3/4W 1W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1%
Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96
Jumper
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
2.2 MΩ
3.3 MΩ
4.7 MΩ
6.8 MΩ
10 MΩ
15 MΩ
22 MΩ
Remark
Note: Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
1206 to 2512
19
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RC1206JR-07100K(L)
R C 1 2 0 6 J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
RC = General purpose thick lm Resistance (code 12-16)
Size code (code 3-6) 0R = Jumper
(inch / metric) 10R = 10Ω
0100 = 0.4 x 0.2 100R = 100Ω
0201 = 0.6 x 0.3 100K = 100KΩ
0402 = 1.0 x 0.5
0603 = 1.6 x 0.8 Taping reel (code 10-11)
0805 = 2.0 x 1.25 07 = 7 inch Dia. reel
1206 = 3.2 x 1.6 10 = 10 inch Dia. reel
1210 = 3.2 x 2.6 13 = 13 inch Dia. reel
1218 = 3.2 x 4.5
2010 = 5.0 x 2.5 T. C. R. (code 9)
2512 = 6.35 x 3.2 “―” = Based on spec.
(― for thick lm only)
Tolerance (code 7)
D = ±0.5% Packing style (code 8 )
F = ±1% R = Paper tape reel
J = ±5% (for Jumper ordering) K = Embossed plastic tape reel
C = Bulk cassette
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
General purpose thick lm / RC series
Size: inch (mm) 1206 (3216) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432)
Power 1/4 W 1/2 W 1 W 3/4 W 1 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1% +5% +1%
Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96
Packing paper tape paper tape blister tape blister tape blister tape
Quantity 4 000
--- --- --- --- 2322 735 64...L 2322 735 7.…L 2322 760 60...L 2322 761 6.…L 2322 762 60...L 2322 763 6.…L
5 000
2322 711 61...L 2322 724 6.…L 2390 735 70...L 2390 735 3.…L --- --- --- --- --- ---
10 000
2322 711 51...L 2322 724 7.…L --- --- --- --- --- --- --- ---
20 000
2322 711 81...L 2322 724 8.…L 2390 735 71...L 2390 735 5.…L --- --- --- --- --- ---
Jumper 4 000
--- --- --- --- 2322 735 90007L --- 2322 760 90003L --- 2322 762 90000L ---
5 000
2322 711 91032L --- 2390 735 90001L --- --- --- --- --- --- ---
10 000
2322 711 91005L --- --- --- --- --- --- --- --- ---
20 000
2322 711 92004L --- --- --- --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
1206 to 2512
20
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
125
Overcoat
Secondary Electrode
(Nickel Plated)
External Electrode
Resistor (NiCr)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
RT / RJ0402 1.00 ±0.10 0.50 ±0.05 0.30 ±0.05 0.20 ±0.10 0.25 ±0.10
RT / RJ0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
RT / RJ 0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
RT / RJ1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
RT / RJ1210 3.10 ±0.10 2.60 ±0.15 0.50 ±0.10 0.50 ±0.20 0.50 ±0.20
RT / RJ2010 5.00 ±0.10 2.50 ±0.15 0.55 ±0.10 0.55 ±0.15 0.50 ±0.20
RT / RJ2512 6.35 ±0.10 3.20 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Features
RT series
High precision - high stability
Low TCR / low noise
High accuracy (±0.05%, ±0.1%, ±0.25%, ±0.5%, ±1%)
RJ series
General purpose
TCR: ±50 ppm/°C
Tolerance: ±1%
•
•
•
•
•
•
Resistor Chip Selection Charts
Introduction to thin film chip resistors
21
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
RT0402 1/16W
-55°C to +125°C
50V 100V 75V
E24/E96
±0.05%, ±0.1%,
±0.25%, ±0.5%, ±1%
10Ω ≤ R ≤ 121KΩ
±50
±25
±15
±10
RT0603 1/10W 75V 150V 100V 10Ω ≤ R ≤ 681KΩ
RT0805 1/8W 150V 300V 200V 10Ω ≤ R ≤ 1.5MΩ
RT1206 1/8W 200V 400V 300V
RT1210 1/4W 200V 400V 400V 10Ω ≤ R ≤ 1MΩ
RT2010 1/2W 200V 400V 400V 10Ω ≤ R ≤ 1MΩ
RT2512 3/4W 200V 400V 400V
RJ0402 1/16W 25V 100V 100V
E24/E96 ±1%
10Ω ≤ R ≤ 121KΩ
±50
RJ0603 1/16W 50V 100V 100V 5.1Ω ≤ R ≤ 681KΩ
RJ0805 1/10W 100V 200V 250V 5.1Ω ≤ R ≤ 1.5MΩ
RJ1206 1/8W 150V 250V 250V
RJ1210 1/4W 150V 250V 250V
10Ω ≤ R ≤ 1MΩRJ2010 1/2W 150V 300V 400V
RJ2512 3/4W 150V 300V 400V
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required
±(0.25% +0.05Ω) for RT
±(0.5% +0.05Ω) for RJ
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at 8 hours
(method 106F), 3 cycles / 24 hours for 10d with
25°C / 65°C 95% R.H
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature
Solderability
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(0.25% +0.05Ω) for RT
±(0.5% +0.05Ω) for RJ
Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistor Chip Selection Charts
Introduction to thin film chip resistors
22
High precision - High stability
Size: inch (mm) 0402 (1005) 0603 (1608)
Power P70 1/16W 1/10W
Temp. range (°C) -55 to +125 -55 to +125
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance range E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
Remark
Note: 1. Resistance range is upper to 2 MΩ (depends on size) on request
2. Value in "Resistance" means the minimum one
3. Resistance E192; special value on request
4. Tolerance = ±0.05%, T.C.R. = ±10 ppm/°C; ±15 ppm/°C on request
5. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R."
Resistor Chip Selection Charts
High precision - High stability, 0402 / 0603
23
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RT0603DRE07100K(L)
R T 0 6 0 3 D R E 0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (1/2) (code 17)
RT = High precision - High stability thin lm Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100R = 100Ω
0402 = 1.0 x 0.5 10K = 10KΩ
0603 = 1.6 x 0.8 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
1210 = 3.2 x 2.6 07 = 7 inch Dia. reel
2010 = 5.0 x 2.5 10 = 10 inch Dia. reel
2512 = 6.35 x 3.2 13 = 13 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
W = ±0.05% B = ±10 ppm/°C (on request)
B = ±0.1% C = ±15 ppm/°C (on request)
C = ±0.25% D = ±25 ppm/°C
D = ±0.5% E = ±50 ppm/°C
F = ±1% Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type High precision - High stability
Size: inch (mm) 0402 (1005) 0603 (1608)
Power 1/16 W 1/10 W
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance E24 / E96 E24 / E96
Packing paper tape paper tape
Quantity TC25 5 000
--- --- --- --- 2390 604 7.…L 2390 604 6.…L 2390 604 5.…L 2390 604 4.…L
TC50 5 000
--- --- --- --- 2390 404 7.…L 2390 404 6.…L 2390 404 5.…L 2390 404 4.…L
TC25 10 000
2390 607 7.…L 2390 607 6.…L 2390 607 5.…L 2390 607 4.…L --- --- --- ---
TC50 10 000
2390 407 7.…L 2390 407 6.…L 2390 407 5.…L 2390 407 4.…L --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Thin lm product range against tolerance / T.C.R. (ordering code)
Tolerance ±0.05% (W) ±0.1% (B) ±0.25% (C) ±0.5% (D) ±1% (F)
T.C.R. (ppm/°C) ±10 (B) ±15 (C) ±25 (D) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±25 (D) ±50 (E) ±50 (E)
RT0402
-- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K
RT0603
1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K
RT0805
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1206
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1210
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M
RT2010
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
RT2512
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
Resistor Chip Selection Charts
High precision - High stability, 0402 / 0603
24
High precision - High stability
Size: inch (mm) 0805 (2012) 1206 (3216) 1210 (3225)
Power P70 1/8W 1/8W 1/4W
Temp. range (°C) -55 to +125 -55 to +125 -55 to +125
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance range E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
Remark
Note: 1. Value in "Resistance" means the minimum one
2. Jumper; Resistance E192; special value on request
3. T.C.R. = ±10 ppm/°C; ±15 ppm/°C on request
4. Tolerance = ±0.01%; ±0.05% on Request
5. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R."
Resistor Chip Selection Charts
High precision - High stability, 0805 to 1210
25
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RT0805DRE07100K(L)
R T 0 8 0 5 D R E 0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (1/2) (code 17)
RT = High precision - High stability thin lm Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100R = 100Ω
0402 = 1.0 x 0.5 10K = 10KΩ
0603 = 1.6 x 0.8 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
1210 = 3.2 x 2.6 07 = 7 inch Dia. reel
2010 = 5.0 x 2.5 10 = 10 inch Dia. reel
2512 = 6.35 x 3.2 13 = 13 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
W = ±0.05% B = ±10 ppm/°C (on request)
B = ±0.1% C = ±15 ppm/°C (on request)
C = ±0.25% D = ±25 ppm/°C
D = ±0.5% E = ±50 ppm/°C
F = ±1% Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type High precision - High stability
Size: inch (mm) 0805 (2012) 1206 (3216) 1210 (3225)
Power 1/8 W 1/4 W 1/2 W
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance E24 / E96 E24 / E96 E24 / E96
Packing paper tape paper tape paper tape
Quantity TC10 5 000
2390 801 7.…L 2390 801 6.…L 2390 801 5....L 2390 801 4....L 2390 811 7....L 2390 811 6....L 2390 811 5....L 2390 811 4....L 2390 812 7....L 2390 812 6....L 2390 812 5....L 2390 812 4....L
TC15 5 000
2390 701 7.…L 2390 701 6.…L 2390 701 5....L 2390 701 4....L 2390 711 7....L 2390 711 6....L 2390 711 5....L 2390 711 4....L 2390 712 7....L 2390 712 6....L 2390 712 5....L 2390 712 4....L
TC25 5 000
2390 601 7.…L 2390 601 6....L 2390 601 5....L 2390 601 4....L 2390 611 7....L 2390 611 6....L 2390 611 5....L 2390 611 4....L 2390 612 7....L 2390 612 6....L 2390 612 5....L 2390 612 4....L
TC50 5 000
2390 401 7.…L 2390 401 6....L 2390 401 5....L 2390 401 4....L 2390 411 7....L 2390 411 6....L 2390 411 5....L 2390 411 4....L 2390 412 7....L 2390 412 6....L 2390 412 5....L 2390 412 4....L
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Thin lm product range against tolerance / T.C.R. (ordering code)
Tolerance ±0.05% (W) ±0.1% (B) ±0.25% (C) ±0.5% (D) ±1% (F)
T.C.R. (ppm/°C) ±10 (B) ±15 (C) ±25 (D) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±25 (D) ±50 (E) ±50 (E)
RT0402
-- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K
RT0603
1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K
RT0805
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1206
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1210
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M
RT2010
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
RT2512
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
Resistor Chip Selection Charts
High precision - High stability, 0805 to 1210
26
High precision - high stability
Size: inch (mm) 2010 (5025) 2512 (6432)
Power P70 1/2W 3/4W
Temp. range (°C) -55 to +125 -55 to +125
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance range E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
Remark
Note: 1. Jumper; Resistance E192; special value on request
2. Value in "Resistance" means the minimum one.
3. T.C.R. = ±10 ppm/°C; ±15 ppm/°C on request
4. Tolerance = ±0.01%; ±0.05% on request
5. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R."
Resistor Chip Selection Charts
High precision - High stability, 2010 / 2512
27
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RT2010DRE07100K(L)
R T 2 0 1 0 D R E 0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (1/2) (code 17)
RT = High precision - High stability thin lm Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100R = 100Ω
0402 = 1.0 x 0.5 10K = 10KΩ
0603 = 1.6 x 0.8 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
1210 = 3.2 x 2.6 07 = 7 inch Dia. reel
2010 = 5.0 x 2.5 10 = 10 inch Dia. reel
2512 = 6.35 x 3.2 13 = 13 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
W = ±0.05% B = ±10 ppm/°C (on request)
B = ±0.1% C = ±15 ppm/°C (on request)
C = ±0.25% D = ±25 ppm/°C
D = ±0.5% E = ±50 ppm/°C
F = ±1% Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type High precision - High stability
Size: inch (mm) 2010 (5025) 2512 (6432)
Power 1/2 W 3/4 W
Tolerance ±1% ±0.5% ±0.25% ±0.1% ±1% ±0.5% ±0.25% ±0.1%
Resistance E24 / E96 E24 / E96
Packing blister tape blister tape
Quantity TC10 4 000
2390 815 7....L 2390 815 6....L 2390 815 5....L 2390 815 4....L 2390 818 7....L 2390 818 6....L 2390 818 5....L 2390 818 4....L
TC15 4 000
2390 731 7....L 2390 731 6....L 2390 731 5....L 2390 731 4....L 2390 735 7....L 2390 735 6....L 2390 735 5....L 2390 735 4....L
TC25 4 000
2390 615 7....L 2390 615 6....L 2390 615 5....L 2390 615 4....L 2390 618 7....L 2390 618 6....L 2390 618 5....L 2390 618 4....L
TC50 4 000
2390 415 7....L 2390 415 6....L 2390 415 5....L 2390 415 4....L 2390 418 7....L 2390 418 6....L 2390 418 5....L 2390 418 4....L
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Thin lm product range against tolerance / T.C.R. (ordering code)
Tolerance ±0.05% (W) ±0.1% (B) ±0.25% (C) ±0.5% (D) ±1% (F)
T.C.R. (ppm/°C) ±10 (B) ±15 (C) ±25 (D) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±10 (B) ±15 (C) ±25 (D) ±50 (E) ±25 (D) ±50 (E) ±50 (E)
RT0402
-- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K
RT0603
1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K
RT0805
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1206
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M
RT1210
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M
RT2010
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
RT2512
100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M
Resistor Chip Selection Charts
High precision - High stability, 2010 / 2512
28
General purpose thin film / RJ Series
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1210 (3225) 2010 (5025) 2512 (6432)
Power P70 1/16W 1/16W 1/10W 1/8W 1/4W 1/2W 3/4W
Tolerance ±1% ±1% ±1% ±1% ±1% ±1% ±1%
Temperature
Coefficient of
Resistance
±50 ppm/°C ±50 ppm/°C ±50 ppm/°C ±50 ppm/°C ±50 ppm/°C ±50 ppm/°C ±50 ppm/°C
Resistance Range E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
Remark
Note: 1. Value in "Resistance" means the minimum one.
2. Resistance E192; special value on request
3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
General Purpose, 0402 to 2512
29
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RJ0603FRE07100K(L)
R J 0 6 0 3 F R E 0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (1/2) (code 17)
RJ = General purpose thin lm Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100R = 100Ω
0402 = 1.0 x 0.5 10K = 10KΩ
0603 = 1.6 x 0.8 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
1210 = 3.2 x 2.6 07 = 7 inch Dia. reel
2010 = 5.0 x 2.5 10 = 10 inch Dia. reel
2512 = 6.35 x 3.2 13 = 13 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
F = ±1% E = ±50 ppm/°C
Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
General purpose thin lm / RJ series
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1210 (3225) 2010 (5025) 2512 (6432)
Power 1/16 W 1/16 W 1/10 W 1/8 W 1/4 W 1/2 W 3/4 W
Tolerance +1% +1% +1% +1% +1% +1% +1%
Resistance E24 / E96 E24 / E96 E24 / E96 E24 / E96 E24 / E96 E24 / E96 E24 / E96
Packing paper tape paper tape paper tape paper tape paper tape blister tape blister tape
Quantity 4 000 --- --- --- --- --- 2390 415 8.…L 2390 418 8.…L
5 000 --- 2390 404 8.…L 2390 401 8.…L 2390 411 8.…L 2390 412 0.…L --- ---
10 000 2390 407 8.…L 2391 424 8.…L 2391 421 8.…L 2391 431 8.…L 2391 432 8.…L --- ---
20 000 2390 427 8.…L 2392 444 8.…L 2392 441 8.…L 2392 451 8.…L 2392 412 8.…L --- ---
50 000 2390 447 8.…L --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Thin lm product range against tolerance / T.C.R. (ordering code)
Tolerance ±1% (F)
T.C.R. (ppm/°C) ±50 (E)
RJ0402 10R - 121K
RJ0603 5R1 - 681K
RJ0805 5R1 - 1.5M
RJ1206 5R1 - 1.5M
RJ1210 10R - 1M
RJ2010 10R - 1M
RJ2512 10R - 1M
Resistor Chip Selection Charts
General Purpose, 0402 to 2512
30
Features
Integrated discrete chip resistors from 2 to 8 pcs
More efcient in pick & place application
Low assembly costs
Reduced size of nal equipment
Higher component and equipment reliability
•
•
•
•
•
Schematics
TC122
R1 = R2
R1 = R2
YC102/122/162
4 3
1 2
R2R1
4 3
R2R1
1 2
TC124/164
R1 = R2 = R3 = R4
YC124/164/324
R1 = R2 = R3 = R4
5 6 7 8
1 2 3 4
R1 R2 R3 R4
YC158
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
YC248
R1 R2 R3 R4 R5 R6 R7 R8
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
1 2 3 4 5
10 9 8 7 6
R1 R2 R3 R4
R8 R7 R6 R5
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
YC358 (L-Type)
YC358 (T-Type)
R1 R2 R3 R4
R8 R7 R6 R5
1 2 3 4 5
10 9 8 7 6
1 2 3 4 5
10 9 8 7 6
R1 R2 R3 R4
R8 R7 R6 R5
5678
1234
R1 R2 R3 R4
Dimensions
Side view for all types
T
W1
W2
YC 102/122/162
H
B
P
L
YC 124/164/324
158/358/248
H
L
B
H2
a
a
P
L
TC 122
P
L
B
HTC 124/164
B
Ha
a
P
H2
Note: "H2" is valued on button view unit: mm
Type H / H2B P L T W1W2
YC102 H: 0.35 ±0.10 0.20 ±0.10 0.50 ±0.05 0.80 ±0.10 0.35 ±0.10 0.15 ±0.10 0.60 ±0.10
YC122 H: 0.21 +0.10/-0.05 0.20 ±0.10 0.67 ±0.05 1.00 ±0.10 0.35 ±0.10 0.25 ±0.10 1.00 ±0.10
YC162 H: 0.30 ±0.10 0.30 ±0.10 0.80 ±0.05 1.60 ±0.10 0.40 ±0.10 0.30 ±0.10 1.60 ±0.10
YC124 H: 0.45 ±0.05 0.20 ±0.15 0.50 ±0.05 2.00 ±0.10 0.45 ±0.10 0.30 ±0.15 1.00 ±0.10
YC164 H: 0.65 ±0.05 0.30 ±0.15 0.80 ±0.05 3.20 ±0.15 0.60 ±0.10 0.30 ±0.15 1.60 ±0.15
YC324 H: 1.10 ±0.15
H
2
: 0.90 ±0.15 0.50 ±0.20 1.27 ±0.05 5.08 ±0.20 0.60 ±0.10 0.50 ±0.15 3.20 ±0.20
YC248 H: 0.45 ±0.05
H
2
: 0.30 ±0.05 0.30 ±0.15 0.50 ±0.05 4.00 ±0.20 0.45 ±0.10 0.40 ±0.15 1.60 ±0.15
TC122 H: 0.30 ±0.05 0.25 ±0.15 0.50 ±0.05 1.00 ±0.10 0.30 ±0.10 0.25 ±0.15 1.00 ±0.10
TC124 H: 0.30 ±0.10
H
2
: 0.25 ±0.10 0.20 ±0.10 0.50 ±0.05 2.00 ±0.10 0.40 ±0.10 0.25 ±0.10 1.00 ±0.10
TC164 H: ---
H
2
: 0.60 ±0.15 0.30 ±0.15 0.80 ±0.05 3.20 ±0.15 0.60 ±0.10 0.30 ±0.15 1.60 ±0.15
YC158 H: 0.45 ±0.05 0.30 ±0.15 0.64 ±0.05 3.20 ±0.20 0.60 ±0.10 0.35 ±0.15 1.60 ±0.15
YC358 H: 1.10 ±0.15
H
2
: 0.90 ±0.15 0.50 ±0.15 1.27 ±0.05 6.40 ±0.20 0.60 ±0.10 0.50 ±0.15 3.20 ±0.20
TC arrays
YC networks YC arrays
Resistor Chip Selection Charts
Introduction to thick film array / network resistors
31
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C) Jumper criteria
(unit: A)
YC102 1/32W -55°C to +125°C 15V 30V 30V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
±200
Rated current
Max. current 0.5
1.0
YC122 1/16W -55°C to +125°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
1Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
2.0
YC162 1/16W -55°C to +125°C 50V 100V 100V E24 ±5%
Zero ohm jumper 10Ω ≤ R ≤ 1MΩ
< 0.05Ω Rated current
Max. current 1.0
2.0
YC124 1/16W -55°C to +155°C 25V 50V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
2.0
YC164 1/16W -55°C to +155°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
1Ω ≤ R ≤ 1MΩ
1Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
2.0
YC324 1/8W -55°C to +155°C 200V 500V 500V E24 ±5%
E24/E96 ±1% 10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ -- --
YC248 1/16W -55°C to +155°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 2.0
10.0
TC122 1/16W -55°C to +125°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
1.5
TC124 1/16W -55°C to +125°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
1.5
TC164 1/16W -55°C to +155°C 50V 100V 100V E24 ±5%
E24/E96 ±1%
Zero ohm jumper
10Ω ≤ R ≤ 1MΩ
10Ω ≤ R ≤ 1MΩ
< 0.05Ω
Rated current
Max. current 1.0
2.0
YC158 1/16W -55°C to +155°C 25V 50V 50V E24 ±5% 10Ω ≤ R ≤ 100KΩ -- --
YC358 1/16W -55°C to +155°C 50V 100V 100V E24 ±5% 10Ω ≤ R ≤ 330KΩ -- --
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
< 100mΩ for jumper
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered
±(1% +0.05Ω)
< 50mΩ for jumper
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at 8 hours
(method 106F), 3 cycles / 24 hours for 10d with
25°C / 65°C 95% R.H
±(2% +0.05Ω)
< 100mΩ for jumper
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω) for 10K to 10M
±(1% +0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
< 50mΩ for jumper
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(2% +0.05Ω)
< 50mΩ for jumper
Resistor Chip Selection Charts
Introduction to thick film array / network resistors
32
Arrays
Series YC / TC 122 series YC / TC 124 series YC248 series YC / TC 164 series YC324 series
Size: inch (mm) 2 x 0402 (1 x 1) 4 x 0402 (2 x 1) 8 x 0602 (4.0 x 1.6) 4 x 0603 (3.2 x 1.6) 4 x 1206 (5.2 x 3.1)
Power P70 1/16W 1/16W 1/16W 1/16W 1/8W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1% ±5%
Type
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(concave)
R-Array/R
-Network
(convex)
R-Array/R
-Network
(convex)
Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24
Jumper
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
Remark
Note: 1. Zero ohm Jumper <0.05 Ω
2. Value in "Resistance" means the minimum one
3. 4 x 0603 (Concave) 1% on request
4. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
Arrays, convex and concave
33
Global part number - Arrays & Networks
Ordering example: YC122-JR-07100K(L)
Y C 1 2 2 ―J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (code 17)
YC = Aarray & Network (convex) thick lm
TC = Array (concave) thick lm Resistance (code 12-16)
TA = Array (convex) thin lm 0R = Jumper
TD = Multi value array (convex) thin lm 10R = 10Ω
100R = 100Ω
Size code (inch) (code 3-4) 100K = 100KΩ
10 = 0201 x 2 (0202)
12 = 0402 x 2 (0404) Taping reel (code 10-11)
0402 x 4 (0408) 07 = 7 inch Dia. reel
15 = 10Pin/8R (0612) 10 = 10 inch Dia. reel
16 = 0603 x 2 (0606) 13 = 13 inch Dia. reel
0603 x 4 (0612)
24 = 0602 x 8 (0616) T.C.R. (code 9)
32 = 1206 x 4 (1224) “―” = Based on spec.
35 = 10Pin/8R (1225) Packing style (code 8 )
Number of resistors (code 5) R = Paper tape reel
2 = 2 resistors K = Embossed plastic tape reel
4 = 4 resistors
8 = 8 resistors Tolerance (code 7)
F = ±1%
Schematic (code 6) J = ±5% (for Jumper ordering)
L = L-type (for YC358)
T = T-type (for YC158/358)
“―” = Based on spec.
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
Array thick lm chip resistors
Size: inch / mm 2 X 0402 /
1 X 1 4 X 0402 /
2 X 1 8 X 0402 /
4.0 X 1.6 4 X 0603 /
3.2 X 1.3 4 X1206 /
5.2 X 3.1
Power 1/16 W 1/16 W 1/16 W 1/16 W 1/8 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1% +5% +5%
Type R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
R-array /
R-network
(convex)
Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24
Packing paper tape paper tape paper tape paper tape blister tape
Quantity 4 000
--- --- --- --- --- --- --- --- --- 2350 039 10...L
5 000
--- --- --- --- 2350 053 10...L 2350 043 1....L 2350 035 10...L 2350 025 1....L 2350 034 10...L ---
10 000
2350 013 11...L 2350 013 2....L 2350 033 11...L 2350 023 2....L --- --- --- --- --- ---
Jumper 5 000
--- --- --- --- 2350 053 91001L --- 2350 035 91001L --- 2350 034 91001L ---
10 000
2350 013 91001L --- 2350 033 91001L --- --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Arrays, convex and concave
34
Network
series YC158 series YC358 series
Size: inch (mm) 0612 (1632) 1225 (3264)
Power P70 1/16W 1/16W
Tolerance ±5% ±5%
Type T-Type 10 Pin,
PIN 5 and PIN 10 no resistance
T-Type 10 Pin,
PIN 5 and PIN 10 no resistance
L-Type 10 Pin,
PIN 1 and PIN 6 no resistance
Resistance Range E24 E24 E24
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
Remark
Note: 1. 8R-Network, convex termintions
2. Zero ohm Jumper <0.05 Ω
3. Value in "Resistance" means the minimum one.
4. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
Networks, T-type and L-type
35
Global part number - Arrays & Networks
Ordering example: YC158TJR-07100K(L)
Y C 1 5 8 T J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code (code 17)
YC = Aarray & Network (convex) thick lm
TC = Array (concave) thick lm Resistance (code 12-16)
0R = Jumper
Size code (inch) (code 3-4) 10R = 10Ω
10 = 0201 x 2 (0202) 100R = 100Ω
12 = 0402 x 2 (0404) 100K = 100KΩ
0402 x 4 (0408)
15 = 10Pin/8R (0612) Taping reel (code 10-11)
16 = 0603 x 2 (0606) 07 = 7 inch Dia. reel
0603 x 4 (0612) 13 = 13 inch Dia. reel
24 = 0602 x 8 (0616)
32 = 1206 x 4 (1224) T.C.R. (code 9)
35 = 10Pin/8R (1225) “―” = Based on spec.
Number of resistors (code 5) Packing style (code 8 )
2 = 2 resistors R = Paper tape reel
4 = 4 resistors K = Embossed plastic tape reel
8 = 8 resistors Tolerance (code 7)
Schematic (code 6) F = ±1%
L = L-type (for YC358) J = ±5% (for Jumper ordering)
T = T-type (for YC158/358)
“―” = Based on spec.
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
Network thick lm chip resistors
Size: inch (mm) 0612 (1632) 1225 (3264)
Power 1/32 W 1/16 W
Tolerance +5% +5%
Type T-type 10 Pin / 8R
PIN 5 and PIN 10 no resistance T-type 10 Pin / 8R
PIN 5 and PIN 10 no resistance L-type 10 Pin / 8R
PIN 1 and PIN 6 no resistance
Resistance E24 E24 E24
Packing paper tape blister tape
Quantity 4 000 --- 2350 201 10...L 2350 200 10...L
5 000 2350 230 10...L --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Networks, T-type and L-type
36
Features
Precision
Low TCR
Reduced size of nal equipment
Lower assembly costs
Higher component and equipment reliability
•
•
•
•
•
Derating curve Schematics
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
125
TA164
8 7 6 5
1 2 3 4
R1 R2 R3 R4
TD164
8 7 6 5
1 2 3 4
R1 R2 R3 R4
R1 = R2 = R3 = R4 R1 R2 R3 R4
Dimensions
TA/TD 164 H H3
B
P
L
top view
H4H2
button view
T
W1
W2
side view unit: mm
Type H H3B P L H2H4T W1W2
TA164 0.65 ±0.05 0.50 ±0.15 0.30 ±0.15 0.80 ±0.05 3.20 ±0.15 0.50 ±0.15 0.65 ±0.05 0.50 ±0.10 0.30 ±0.15 1.60 ±0.15
TD164 0.65 ±0.10 0.50 ±0.10 0.30 ±0.15 0.80 ±0.15 3.20 ±0.20 0.40 ±0.10 0.50 ±0.10 0.50 ±0.10 0.30 ±0.15 1.60 ±0.10
Resistor Chip Selection Charts
Introduction to thin film array chip resistors
37
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
TA164 1/16W -55°C to +125°C 75V 150V 150V E24/E96 ±0.1%, ±0.5%, ±1% 10Ω ≤ R ≤ 330KΩ ±25
±50
TD164 1/16W -55°C to +125°C 75V 150V 150V E24/E96 ±0.1%, ±0.5%, ±1% 10Ω ≤ R ≤ 330KΩ
Note: See page 11 for ordering code. For more detailed, please contact with sales ofces, distributors and representatives in your region.
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(0.25% +0.05Ω) for TD164
±(0.5% +0.05Ω) for TA164
High temperature
exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered Satisfy electrical and
physical characteristic
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at 8 hours
(method 106F), 3 cycles / 24 hours for 10d with
25°C / 65°C 95% R.H ±(0.25% +0.05Ω) for TD164
±(0.5% +0.05Ω) for TA164
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time Satisfy electrical and
physical characteristic
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(0.25% +0.05Ω) for TD164
±(0.5% +0.05Ω) for TA164
Resistor Chip Selection Charts
Introduction to thin film array chip resistors
38
Features
Current sensing of desktop & notebook PC
Resistance values down to 0.010Ω
Highly reliable multilayer electrode construction
Low inductance
High speed logic circuits
•
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
125
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (Ag)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
RL0402 1.00 ±0.10 0.50 ±0.05 0.35 ±0.05 0.20 ±0.10 0.25 ±0.10
RL0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
RL0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
RL1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.45±0.20
RL1210 3.10 ±0.10 2.60 ±0.15 0.50 ±0.10 0.50 ±0.20 0.50 ±0.20
RL1218 3.05 ±0.15 4.60 ±0.10 0.55 ±0.10 0.45 ±0.25 0.50 ±0.25
RL2010 5.00 ±0.10 2.50 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
RL2512 6.35 ±0.10 3.20 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Resistor Chip Selection Charts
Introduction to low ohmic / low ohmic high power chip resistors
39
Electrical characteristics
Type Power
P70
Operating Temp.
range Resistance range & tolerance T. C. R.
( ppm/°C)
RL0402 1/16W -55°C to +125°C
E24 ±1%, ±2%, ±5%
0.05Ω ≤ R < 1Ω
See following table “T.C.R.- RL series”
RL0603 1/10W -55°C to +125°C
0.01Ω ≤ R < 1Ω
RL0805 1/8W -55°C to +125°C
RL1206 1/4W -55°C to +125°C
RL1210 1/2W -55°C to +125°C
RL1218 1W -55°C to +125°C
RL2010 3/4W -55°C to +125°C
RL2512 1W -55°C to +125°C
High power RL0805 1/4W -55°C to +125°C 0.015Ω ≤ R < 1Ω
High power RL1206 1/2W -55°C to +125°C
T. C. R. - RL series
Type Operating
Temp. range Resistance
range T. C. R.
50mΩ - 1Ω
RL0402 -55°C to +125°C 50mΩ≤R<1Ω ±800 ppm/°C
10mΩ - 36mΩ 36mΩ - 91mΩ 91mΩ - 500mΩ 500mΩ - 1Ω
RL0603 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±800 ppm/°C ±300 ppm/°C
10mΩ - 18mΩ 20mΩ - 47mΩ 51mΩ - 91mΩ 100mΩ - 360mΩ 390mΩ - 500mΩ 510mΩ - 1Ω
RL0805 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL1206 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL1210 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 000 ppm/°C ±800 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
10mΩ - 30mΩ 33mΩ - 56mΩ 60mΩ - 180mΩ 200mΩ - 1Ω
RL1218 -55°C to +125°C 10mΩ≤R<1Ω ±2 000 ppm/°C ±1 000 ppm/°C ±700 ppm/°C ±250 ppm/°C
10mΩ - 18mΩ 20mΩ - 47mΩ 51mΩ - 91mΩ 100mΩ - 360mΩ 390mΩ - 500mΩ 510mΩ - 1Ω
RL2010 -55°C to +125°C 10mΩ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±1 000 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
RL2512 -55°C to +125°C 10mΩ ≤R<1Ω ±1 500 ppm/°C ±1 200 ppm/°C ±800 ppm/°C ±600 ppm/°C ±300 ppm/°C ±200 ppm/°C
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70°C ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±2%
High temperature
exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered ±1%
Moisture resistance MIL-STD-202G-
method 106F Each tempperature / humidity cycle is dened at 8 hours (method
106F), 3 cycles / 24 hours for 10d with 25°C / 65°C 95% R.H ±2%
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±1%
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned
(≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±1%
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage
whichever is less for 5 seconds at room temperature ±2%
Resistor Chip Selection Charts
Introduction to low ohmic / low ohmic high power chip resistors
40
Low ohmic / RL series
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power P70 1/16W 1/10W 1/8W 1/4W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1%
Resistance Range E24 E24 E24 E24 E24 E24 E24 E24
0.01 Ω
0.02 Ω
0.03 Ω
0.04 Ω
0.05 Ω
0.06 Ω
0.07 Ω
0.08 Ω
0.09 Ω
0.1 Ω
0.2 Ω
0.3 Ω
0.4 Ω
0.5 Ω
0.6 Ω
0.7 Ω
0.8 Ω
0.9 Ω
Remark
Note: 1. Value in "Resistance" means the minimum one
2. E48/E96 on request
3. The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 mΩ are also available
4. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
Low ohmic, 0201 to 1206
41
Global part number - Preferred type
Ordering example: RL0603JR-070R01(L)
R L 0 6 0 3 J R ―0 7 0 R 0 1 ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
RL = Low ohmic Resistance (code 12-16)
Size code (code 3-6) 0R01 = 0.01Ω
(inch / metric) 0R1 = 0.1Ω
0402 = 1.0 x 0.5 0R2 = 0.2Ω
0603 = 1.6 x 0.8
0805 = 2.0 x 1.25 Taping reel (code 10-11)
1206 = 3.2 x 1.6 07 = 7 inch Dia. reel
1210 = 3.2 x 2.6 10 = 10 inch Dia. reel
1218 = 3.2 x 4.5 13 = 13 inch Dia. reel
2010 = 5.0 x 2.5
2512 = 6.35 x 3.2 T. C. R. (code 9)
“―” = Based on spec.
Tolerance (code 7) (― for thick lm only)
F = ±1%
G = ±2% Packing style (code 8 )
J = ±5% (for Jumper ordering) R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Low ohmic chip resistors
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power 1/16 W 1/10 W 1/8 W 1/4 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1%
Resistance E24 E24 E24 E24 E24 E24 E24 E24
Packing paper tape paper tape paper tape paper tape
Quantity 5 000 --- --- 2350 512 10…L 2350 512 12…L 2350 511 10…L 2350 511 12…L 2350 510 10…L 2350 510 12…L
10 000 2350 513 20…L 2350 513 22…L --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Low ohmic, 0201 to 1206
42
Low ohmic / RL series
Size: inch (mm) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432)
Power P70 1/2W 1W 3/4W 1W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1%
Reisitance Range E24 E24 E24 E24 E24 E24 E24 E24
0.01 Ω
0.02 Ω
0.03 Ω
0.04 Ω
0.05 Ω
0.06 Ω
0.07 Ω
0.08 Ω
0.09 Ω
0.1 Ω
0.2 Ω
0.3 Ω
0.4 Ω
0.5 Ω
0.6 Ω
0.7 Ω
0.8 Ω
0.9 Ω
Remark
Note: 1. Value in "Resistance" means the minimum one
2. E48/E96 on request
3. The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 mΩ are also available
4. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
Low ohmic, 1210 to 2512
43
Global part number - Preferred type
Ordering example: RL1210JR-070R01(L)
R L 1 2 1 0 J R ―0 7 0 R 0 1 ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
RL = Low ohmic Resistance (code 12-16)
Size code (code 3-6) 0R01 = 0.01Ω
(inch / metric) 0R1 = 0.1Ω
0402 = 1.0 x 0.5 0R2 = 0.2Ω
0603 = 1.6 x 0.8
0805 = 2.0 x 1.25 Taping reel (code 10-11)
1206 = 3.2 x 1.6 07 = 7 inch Dia. reel
1210 = 3.2 x 2.6
1218 = 3.2 x 4.5 T. C. R. (code 9)
2010 = 5.0 x 2.5 “―” = Based on spec.
2512 = 6.35 x 3.2 (― for thick lm only)
Tolerance (code 7) Packing style (code 8 )
F = ±1% R = Paper tape reel
G = ±2% K = Embossed plastic tape reel
J = ±5% (for Jumper ordering)
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Low ohmic chip resistors
Size: inch (mm) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432)
Power 1/2 W 1 W 3/4 W 1 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1%
Resistance E24 E24 E24 E24 E24 E24 E24 E24
Packing paper tape blister tape blister tape blister tape
Quantity 4 000
--- --- 2322 735 64…L 2322 735 7….L 2322 760 90..0L/60..7L 2322 761 90..0L/6...7L 2322 762 90..0L/60..7L 2322 763 90..0L/6...7L
5 000
2390 735 90..0L/60..7L 2390 735 3….L --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Low ohmic, 1210 to 2512
44
Low ohmic high power / RL-High power series
Size: inch (mm) 0805 (2012) 1206 (3216)
Power P70 1/4W 1/2W
Tolerance ±5% ±1% ±5% ±1%
Resistance Range E24 E24 E24 E24
0.01 Ω
0.02 Ω
0.03 Ω
0.04 Ω
0.05 Ω
0.06 Ω
0.07 Ω
0.08 Ω
0.09 Ω
0.1 Ω
0.2 Ω
0.3 Ω
0.4 Ω
0.5 Ω
0.6 Ω
0.7 Ω
0.8 Ω
0.9 Ω
Remark
Note: 1. E48/E96 on request
2. The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 mΩ are also available
3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
Low ohmic, high power, 0805 / 1206
45
Global part number - Preferred type
Ordering example: RL0805JR-7W0R01(L)
R L 0 8 0 5 J R ―7 W 0 R 0 1 ( L )
Series name (code 1-2) Optional code (code 17)
RL = Low ohmic Resistance (code 12-16)
Size code (code 3-6) 0R01 = 0.01Ω
(inch / metric) 0R1 = 0.1Ω
0805 = 2.0 x 1.25 0R2 = 0.2Ω
1206 = 3.2 x 1.6 Taping reel (code 10-11)
Tolerance (code 7) 7W = 7 inch Dia. reel and
2 x standard power type
F = ±1%
G = ±2%
J = ±5% T. C. R. (code 9)
“―” = Based on spec.
Packing style (code 8 ) (― for thick lm only)
R = Paper tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Low ohmic high power chip resistors
Size: inch (mm) 0805 (2012) 1206 (3216)
Power 1/4 W 1/2 W
Tolerance +5% +1% +5% +1%
Resistance E24 E24 / E96 E24 E24 / E96
Packing paper tape paper tape
Quantity 5 000 2350 511 15…L 2350 511 17…L 2350 519 01…L 2350 519 1.…L
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Low ohmic, high power, 0805 / 1206
46
Features
Reduced size of nal equipment
Low assembly costs
Higher component and equipment reliability
High ohmic values up to 100MW
Suitable for power supplies in small equipments
•
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
RC0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
RC1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
Resistor Chip Selection Charts
Introduction to high ohmic chip resistors
47
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
RC0805 1/8W -55°C to +155°C 150V 300V 300V E24 ±5%, ±10%, ±20% 24MΩ ≤ R ≤ 100MΩ ±300
RC1206 1/4W -55°C to +155°C 200V 400V 500V
Note: See page 10 for ordering code. For more detailed, please contact with sales ofces, distributors and representatives in your region.
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered ±(1% +0.05Ω)
Moisture resistance MIL-STD-202G-
method 106F Each temperature / humidity cycle is dened at 8 hours (method
106F), 3 cycles / 24 hours for 10d with 25°C / 65°C 95% R.H ±(2% +0.05Ω)
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω)
±(1% +0.05Ω)
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned
(≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(2% +0.05Ω)
Resistor Chip Selection Charts
Introduction to high ohmic chip resistors
48
Features
New Ni/Au terminations provide special application for
hybrid board gluing
Competitive with AgPd terminations
Special use in high temperature environment
Higher component and equipment reliability
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
(Jumper chip is a conductor)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
AR0402 1.00 ±0.05 0.50 ±0.05 0.35 ±0.05 0.20 ±0.10 0.25 ±0.10
AR0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
AR0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
AR1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
Resistor Chip Selection Charts
Introduction to Ni/Au terminations chip resistors
49
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C) Jumper criteria
(unit: A)
AR0402 1/16W -55°C to +155°C 50V 100V 100V
E24 ±5%
E24/E96 ±1% 1Ω ≤ R ≤10MΩ 10Ω < R ≤ 10MΩ
1Ω ≤ R ≤ 10Ω ±100
±200
Rated current
Max. current 1.0
2.0
AR0603 1/10W -55°C to +155°C 50V 100V 100V Rated current
Max. current 1.0
2.0
AR0805 1/8W -55°C to +125°C 150V 300V 300V Zero ohm jumper < 0.05Ω Rated current
Max. current 2.0
5.0
AR1206 1/4W -55°C to +125°C 200V 500V 500V Rated current
Max. current 2.0
10.0
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
<100mΩ for jumper
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered
±(1% +0.05Ω)
<50mΩ for jumper
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at 8 hours
(method 106F), 3 cycles / 24 hours for 10d with
25°C / 65°C 95% R.H
±(2% +0.05Ω)
<100mΩ for jumper
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω) for 10K to 10M
±(1% +0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
<50mΩ for jumper
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(2% +0.05Ω)
<50mΩ for jumper
Resistor Chip Selection Charts
Introduction to Ni/Au terminations chip resistors
50
Chip resistors with NiAu terminations / AR series
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power P70 1/16W 1/10W 1/8W 1/4W
Tolerance ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1%
Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96
Jumper
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
2.2 MΩ
3.3 MΩ
4.7 MΩ
6.8 MΩ
10 MΩ
Remark
Note: 1. Zero ohm Jumper <0.05 Ω
2. Value in "Resistance" means the minimum one
3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
0402 to 1206
51
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: AR0603JR-07100K
A R 0 6 0 3 J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
AR = NiAu termination Resistance (code 12-16)
Size code (code 3-6) 0R = Jumper
(inch / metric) 10R = 10Ω
0402 = 1.0 x 0.5 100R = 100Ω
0603 = 1.6 x 0.8 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
07 = 7 inch Dia. reel
Tolerance (code 7)
F = ±1% T. C. R. (code 9)
J = ±5% (for Jumper ordering) “―” = Based on spec.
(― for thick lm only)
Packing style (code 8 )
R = Paper tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Chip resistors with Ni/Au terminations
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power 1/16 W 1/10 W 1/8 W 1/4 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1%
Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96
Packing paper tape paper tape paper tape paper tape
Quantity 5 000 --- --- 2322 702 11… 2322 704 1.… 2322 730 11… 2322 734 1.… 2322 711 11... 2322 729 1.…
10 000 2322 705 12… 2322 706 2…. --- --- --- --- --- ---
Jumper 5 000 --- --- 2322 702 19001 --- 2322 730 19001 --- 2322 711 19001 ---
10 000 2322 705 19001 --- --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
0402 to 1206
52
Features
Reduced size of nal equipment
Low assembly costs
Higher component and equipment reliability
Excellent performance at pulse loading
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
(Jumper chip is a conductor)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
SR0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
SR1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
SR1218 3.10 ±0.10 4.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
SR2512 6.35 ±0.10 3.10 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Resistor Chip Selection Charts
Introduction to Surge chip resistors
53
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
SR0805 1/8W -55°C to +155°C 150V 300V 300V
E24 ±5%, ±10%, ±20% 1Ω ≤ R ≤ 100KΩ ±200
SR1206 1/4W -55°C to +155°C 150V 400V 500V
SR1218 1W -55°C to +155°C 200V 400V 500V
SR2512 1W -55°C to +155°C 200V 400V 500V
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered ±(1% +0.05Ω)
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at 8 hours
(method 106F), 3 cycles / 24 hours for 10d with
25°C / 65°C 95% R.H ±(2% +0.05Ω)
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω) for 10K to 10M
±(1% +0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature ±(2% +0.05Ω)
Resistor Chip Selection Charts
Introduction to Surge chip resistors
54
Surge / SR series
Size: inch (mm) 0805 (2012) 1206 (3216) 1218 (3248) 2512 (6432)
Power P70 1/8W 1/4W 1W 1W
Tolerance ±5% ±5% ±5% ±5%
Resistance Range E24 E24 E24 E24
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
Remark
Note: 1. Value in "Resistance" means the minimum one
2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
0805 to 2512
55
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: SR0805MR-07100K(L)
S R 0 8 0 5 M R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
SR = Surge Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100K = 100KΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
1218 = 3.2 x 4.5 07 = 7 inch Dia. reel
2512 = 6.35 x 3.2 T. C. R. (code 9)
Tolerance (code 7) “―” = Based on spec.
J = ±5% (for Jumper ordering) (― for thick lm only)
K = ±10%
M = ±20% Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Surge chip resistors
Size: inch (mm) 0805 (2012) 1206 (3216) 1218 (3248) 2512 (6432)
Power 1/8 W 1/4 W 1 W 1 W
Tolerance +10% +5% +10% +5% +10% +20%
Resistance E24 E24 E24 E24 E24 E24
Packing paper tape paper tape paper tape paper tape paper tape paper tape
Quantity 4 000 --- --- 2350 557 10…L 2350 556 11…L 2350 556 10…L 2350 556 13…L
5 000 2350 554 12…L 2350 550 10…L --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
0805 to 2512
56
Features
Higher maximum working voltage to RC series
Extremely thin and light
Reliable electrode construction
Compatible with lead containing and lead free soldering
processes
Highly stable in auto-placement surface mounting
•
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
Overcoat
(Epoxy)
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
(Jumper chip is a conductor)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
RV0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
RV1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.40 ±0.20 0.40 ±0.20
RV2512 6.35 ±0.10 3.10 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Resistor Chip Selection Charts
Introduction to high voltage chip resistors
57
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
RV0805 1/8W -55°C to +155°C 400V 800V 800V E24 ±5%
E24/E96 ±1% 100KΩ ≤ R ≤ 10MΩ ±200
RV1206 1/4W -55°C to +155°C 500V 1000V 1000V E24 ±5%
E24/E96 ±1% 100KΩ ≤ R ≤ 27MΩ ±200
RV2512 1W -55°C to +155°C 500V 1000V 1000V E24 ±5% 4.7MΩ ≤ R ≤ 16MΩ ±200
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered ±(1% +0.05Ω)
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at
8 hours (method 106F), 3 cycles / 24 hours
for 10d with 25°C / 65°C 95% R.H ±(2% +0.05Ω)
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω) for 10K to 10M
±(1% +0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage
whichever is less for 5 seconds at room temperature ±(2% +0.05Ω)
Resistor Chip Selection Charts
Introduction to high voltage chip resistors
58
High voltage / RV series
Size: inch (mm) 0805 (2012) 1206 (3216) 2512 (6432)
Working Voltage 400V 500V 500V
Power P70 1/8W 1/4W 1W
Tolerance ±5% ±1% ±5% ±1% ±5%
Resistance Range E24 E24/E96 E24 E24/E96 E24
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
2.2 MΩ
3.3 MΩ
4.7 MΩ
6.8 MΩ
10 MΩ
15 MΩ
22 MΩ
Remark
Note: 1. Value in "Resistance" means the minimum one
2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
0805 to 2512
59
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: RV0805JR-07100K(L)
R V 0 8 0 5 J R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
RV = High voltage Resistance (code 12-16)
Size code (code 3-6) 100K = 100KΩ
(inch / metric) 1M = 1MΩ
0805 = 2.0 x 1.25
1206 = 3.2 x 1.6 Taping reel (code 10-11)
2512 = 6.35 x 3.2 07 = 7 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
F = ±1% “―” = Based on spec.
J = ±5% (for Jumper ordering) (― for thick lm only)
Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type High voltage chip resistors
Size: inch (mm) 0805 (2012) 1206 (3216) 2512 (6432)
Power 1/8 W 1/4 W 1 W
Tolerance +5% +1% +5% +1% +5%
Resistance E24 E24 / E96 E24 E24 / E96 E24
Packing paper tape paper tape blister tape
Quantity 4 000 --- --- --- --- 2322 762 98...L
5 000 2322 792 61...L 2322 793 6....L 2322 790 61...L 2322 791 6....L ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
0805 to 2512
60
Features
Reduced size of nal equipment
Low assembly costs
Higher component and equipment reliability
Improved performance at high frequency
Low noise, when not trimmed
•
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
TR0805-
TR1206
125
TR0402-
TR0603
Primary glass laye
r
Secondary Electrode
(Nickel plated)
External electrode
(matte Tin)
Resistor (RuO2)
(Jumper chip is a conductor)
Alumina Substrate
Internal Electrode (Ag-Pd)
Dimensions
W
unit: m
m
I2I2
I1
I1
L
H
Type L W H I1I2
TR0402 1.00 ±0.10 0.50 ±0.05 0.35 ±0.05 0.20 ±0.10 0.25 ±0.10
TR0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
TR0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
TR1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
Resistor Chip Selection Charts
Introduction to trimmable chip resistors
61
Electrical characteristics
Type Power
P70
Operating Temp.
range MWV RCOV DWV Resistance range & tolerance T. C. R.
( ppm/°C)
TR0402 1/16W -55°C to +125°C 50V 100V 100V
E24 +0/-10%, +0/-20%, +0/-30% 1Ω ≤ R ≤ 10MΩ
10Ω < R ≤ 1MΩ ±100
TR0603 1/16W -55°C to +125°C 50V 100V 100V
TR0805 1/8W -55°C to +155°C 150V 300V 500V 1Ω ≤ R ≤ 10Ω
1MΩ < R ≤ 10MΩ ±200
TR1206 1/4W -55°C to +155°C 200V 500V 500V
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(2% +0.05Ω)
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature
depending on specication, unpowered ±(1% +0.05Ω)
Moisture resistance MIL-STD-202G-
method 106F
Each temperature / humidity cycle is dened at
8 hours (method 106F), 3 cycles / 24 hours
for 10d with 25°C / 65°C 95% R.H ±(2% +0.05Ω)
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.05Ω) for 10K to 10M
±(1% +0.05Ω) for others
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned (≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(1% +0.05Ω)
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage
whichever is less for 5 seconds at room temperature ±(2% +0.05Ω)
Resistor Chip Selection Charts
Introduction to trimmable chip resistors
62
Trimmable / TR series
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power P70 1/16W 1/16W 1/8W 1/4W
Tolerance
0/-10%
(Trimma
ble)
0/-20%
(Trimma
ble)
0/-30%
(Trimma
ble)
0/-10%
(Trimma
ble)
0/-20%
(Trimma
ble)
0/-30%
(Trimma
ble)
0/-10%
(Trimma
ble)
0/-20%
(Trimma
ble)
0/-30%
(Trimma
ble)
0/-10%
(Trimma
ble)
0/-20%
(Trimma
ble)
0/-30%
(Trimma
ble)
Resistance Range E24 E24 E24 E24 E24 E24 E24 E24 E24 E24 E24 E24
1 Ω
1.5 Ω
2.2 Ω
3.3 Ω
4.7 Ω
6.8 Ω
10 Ω
15 Ω
22 Ω
33 Ω
47 Ω
68 Ω
100 Ω
150 Ω
220 Ω
330 Ω
470 Ω
680 Ω
1 kΩ
1.5 kΩ
2.2 kΩ
3.3 kΩ
4.7 kΩ
6.8 kΩ
10 kΩ
15 kΩ
22 kΩ
33 kΩ
47 kΩ
68 kΩ
100 kΩ
150 kΩ
220 kΩ
330 kΩ
470 kΩ
680 kΩ
1 MΩ
1.5 MΩ
2.2 MΩ
3.3 MΩ
4.7 MΩ
6.8 MΩ
10 MΩ
Remark
Note: 1. Value in "Resistance" means the minimum one
2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor
element and glass is exempted by RoHS.
Resistor Chip Selection Charts
0402 to 1206
63
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: TR0603MR-07100K(L)
T R 0 6 0 3 M R ―0 7 1 0 0 K ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
TR = Trimmable Resistance (code 12-16)
Size code (code 3-6) 10R = 10Ω
(inch / metric) 100R = 100Ω
0402 = 1.0 x 0.5 100K = 100KΩ
0603 = 1.6 x 0.8
0805 = 2.0 x 1.25 Taping reel (code 10-11)
1206 = 3.2 x 1.6 07 = 7 inch Dia. reel
Tolerance (code 7) T. C. R. (code 9)
K = 0/-10% “―” = Based on spec.
M = 0/-20% (― for thick lm only)
N = 0/-30% Packing style (code 8 )
R = Paper tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type Trimmable chip resistors
Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216)
Power 1/16 W 1/10 W 1/8 W 1/4 W
Tolerance E24 E24 E24 E24
Resistance paper tape paper tape paper tape paper tape
Packing 2350 503 21…L 2350 502 11…L 2350 501 11…L 2350 500 11…L
Quantity 5 000 0/-20%
2350 503 20…L 2350 502 10…L 2350 511 10…L 2350 500 10…L
5 000 0/-30%
on request on request on request 2322 724 94…L
Europe 5 000
2322 792 61...L 2322 793 6....L 2322 791 6....L ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
0402 to 1206
64
Features
Excellent TCR compare to thick lm low ohmic
Precision current sensing control
Excellent performance for current sensing
applicatIons
Ultra low ohmic down to 0.001Ω
•
•
•
•
Derating curve Construction
Maximum dissipation (P) in percentage of
rated power as a function of the operating
ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
155
PR2010
PR2512
PF2512
PT1218
PT2512
125
PT0402 to PT1206
PT2010
H
PF / PT seriesPR series
WR005
I2
protective coat
marking
end termination
L
I1
end termination
metal substrate
protective coat
protective coat
W
L
I1
protective coat
resistive layer
inner electrode
termination
ceramic substrat
e
H
I2
Construction will be adjusted to resistance value
Dimensions
PR seriytts
Type Resistance range L W H l1l2
PR2010 2 mΩ - 6 mΩ 5.10 ±0.20 2.50 ±0.20 0.55 ±0.20 0.75 ±0.20 0.75 ±0.20
PR2512 1 mΩ - 2 mΩ 6.30 ±0.20 3.20 ±0.20 0.75 ±0.15 1.20 ±0.20 1.20 ±0.20
3 mΩ - 5 mΩ 6.30 ±0.20 3.20 ±0.20 0.55 ±0.15 0.60 ±0.20 0.60 ±0.20
Note: For relevant physical dimensions, please refer to above construction outlines
PF series
Type Resistance range L W H l1l2
PF2512 6 mΩ - 14 mΩ 6.50 ±0.25 3.15 ±0.25 0.60 ±0.25 1.00 ±0.25 1.75 ±0.25
15 mΩ - 130 mΩ 0.60 ±0.25
Note: For relevant physical dimensions, please refer to above construction outlines
Please contact with sales ofces, distributors and representatives in your region before order
PT series
Type Resistance range L W H l1l2
PT0402
100 mΩ - 910 mΩ
1.00 ±0.10 0.50 ±0.05 0.35 ±0.05 0.20 ±0.10 0.25 ±0.10
PT0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
PT0805 2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
PT1206 3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.45 ±0.20
PT1210 3.10 ±0.10 2.60 ±0.15 0.50 ±0.10 0.50 ±0.20 0.50 ±0.20
PT1218 3.05 ±0.15 4.60 ±0.10 0.55 ±0.10 0.45 ±0.25 0.50 ±0.25
PT2010 5.00 ±0.10 2.50 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
PT2512 6.35 ±0.10 3.20 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20
Note: For relevant physical dimensions, please refer to above construction outlines
Please contact with sales ofces, distributors and representatives in your region before order
Resistor Chip Selection Charts
Introduction to current sensors - low TCR chip resistors
65
Electrical characteristics
Type Power
P70
Operating Temp.
range Max.
working voltage Tolerance Resistance range & T. C. R.
PR2010 0.5W
-55°C to +155°C
(P x R)^1/2
±1%, ±2%, ±5%
(E24 )
2mΩ ≤ R ≤ 6mΩ ±150 ppm/°C
PR2512 1W 1mΩ ≤ R ≤ 2mΩ
3mΩ ≤ R ≤ 5mΩ ±200 ppm/°C
±100 ppm/°C
PF2512 1W 6mΩ ≤ R ≤ 130mΩ ±100 ppm/°C
Power enhancement PR2010 1W
-55°C to +155°C
2mΩ ≤ R ≤ 6mΩ ±150 ppm/°C
Power enhancement PR2512 2W 1mΩ ≤ R ≤ 2mΩ
3mΩ ≤ R ≤ 5mΩ ±200 ppm/°C
±100 ppm/°C
Power enhancement PF2512 2W 6mΩ ≤ R ≤ 130mΩ ±100 ppm/°C
PT0402 1/16W
-55°C to +125°C
±1%, ±5%
(E24) 100mΩ ≤ R ≤ 910mΩ
±200 ppm/°CPT0603 1/10W
PT0805 1/8W
PT1206 1/4W
±100 ppm/°C
PT1210 1/2W
PT1218 1W -55°C to +155°C
PT2010 3/4W -55°C to +125°C
PT2512 1W -55°C to +155°C
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required ±(1% +0.0005Ω)
High temperature exposure MIL-STD-202G-
method 108A 1 000 hours at maximum operating temperature depending on
specication, unpowered ±(1% +0.0005Ω)
Moisture resistance MIL-STD-202G-
method 106F Each temperature / humidity cycle is dened at 8 hours (method
106F), 3 cycles / 24 hours for 10d with 25°C / 65°C 95% R.H ±(0.5% +0.0005Ω)
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds ±(0.5% +0.0005Ω)
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned
(≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time ±(0.5% +0.0005Ω)
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less
for 5 seconds at room temperature ±(0.5% +0.0005Ω)
Resistor Chip Selection Charts
Introduction to current sensors - low TCR chip resistors
66
Current sensors - Low TCR
Series PR / PF / PT series
Size: inch (mm) 2512 (6432)
Power P70 1W
Tolerance ±5% ±1%
Resistance Range E24 E24
0.0010 Ω
0.0020 Ω
0.0030 Ω
0.0040 Ω
0.0050 Ω
0.0060 Ω
0.01 Ω
0.02 Ω
0.03 Ω
0.04 Ω
0.05 Ω
0.06 Ω
0.07 Ω
0.08 Ω
0.09 Ω
0.1 Ω
0.2 Ω
0.3 Ω
0.4 Ω
0.5 Ω
0.6 Ω
0.7 Ω
0.8 Ω
0.9 Ω
Remark
Note: For sizes of PR2010 and PT0402 to 2512, please contact with sales offices, distributors and representatives in your region before order
Resistor Chip Selection Charts
Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512
67
Global part number - Preferred type
Ordering example: PF2512FKF070R01(L)
P F 2 5 1 2 F K F 0 7 0 R 0 1 ( L )
Series name (code 1-2) Optional code(1/2) (code 17)
PT / PR / PF = Current sensor - low TCR
Resistance (code 12-16)
Size code (code 3-6) 0R01 = 0.01Ω
(inch / metric) 0R1 = 0.1Ω
0402 = 1.0 x 0.5 0R2 = 0.2Ω
0603 = 1.6 x 0.8
0805 = 2.0 x 1.25 Taping reel (code 10-11)
1206 = 3.2 x 1.6 07 = 7 inch Dia. reel
2010 = 5.0 x 2.5 7W = 7 inch Dia. reel and
2 x standard power type
2512 = 6.35 x 3.2
Tolerance (code 7) T. C. R. (code 9)
F = ±1% M = ±75 ppm/°C
G = ±2% F = ±100 ppm/°C
J = ±5% (for Jumper ordering) L = ±150 ppm/°C
G = ±200 ppm/°C
Packing style (code 8 )
R = Paper tape reel
K = Embossed plastic tape reel
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
3. PT series products are available by "Global part number" only
Phycomp world wide - Traditional type Current Sensor - Low TCR / PR series
Size: inch (mm) 2010 (5025) 2512 (6432)
Power 1/2 W 1 W 1 W 2 W
Tolerance +5% +1% +5% +1% +5% +1% +5% +1%
Packing blister tape blister tape
Quantity 4 000 2322 760 63..0L 2322 761 11.. 0L 2322 760 65.. 0L 2322 761 13.. 0L 2322 762 94..0L 2322 763 95..0L 2322 762 10..0L 2322 763 10..0L
5 000 --- --- --- --- --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp world wide - Traditional type Current Sensor - Low TCR / PF series
Size: inch (mm) 2512 (6432)
Power 1 W 2 W
Tolerance +5% +1% +5% +1%
Packing blister tape
Quantity 4 000 2322 764 96..L 2322 764 97..L 2322 764 10..L 2322 764 30..L
5 000 --- --- --- ---
For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number.
Phycomp CTC ordering code - Traditional type - North America
Regional code for ordering Phycomp branded products. Please see page 12 for details.
Resistor Chip Selection Charts
Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512
68
Features
Mobile phone
Receivers
Battery charger
Palmtop computers
PDAs
•
•
•
•
•
Derating curve Construction Schematics
Maximum dissipation (P) in percent-
age of rated power as a function of the
operating ambient temperature (Tamb).
100
80
60
40
20
-55 -40 -20 0 20 40 60 80
70
100 120 140 160
Ambient Temperature (
°C)
Rated Power (%)
125
1 3
2 4
input signal attenuated
output signal
The rectangular marker designates input pin 1
1 3
R2R2
R1
2 4
ATV 321
Dimensions
L
P
B
W
T
D
A
unit: mm
Type L W T A B P D
ATV321 1.00 ±0.10 1.00 ±0.10 0.35 ±0.05 0.33 ±0.10 0.15 ±0.10 0.65 ±0.10 0.25 ±0.10
Resistor Chip Selection Charts
Introduction to RF attenuator chip resistors
69
Electrical characteristics
Type Power
P70
Operating Temp.
range MPV VSWR
(Max.) Impedance Resistance range & tolerance Frequency range
ATV321 40mW -55°C to +125°C 50V 1.3 50Ω
1DB - 5DB ±0.3 dB 1DB - 10DB DC to 2.5 GHz
6DB - 10DB ±0.5 dB
15DB ±1.0 dB 15DB - 20DB DC to 2.0 GHz
20DB ±2.0 dB
Environmental characteristics
Performance test Test method Procedure Requirements
Life MIL-STD-202G-
method 108A 1 000 hours at 70 ±5°C applied RCWV
1.5 hours on, 0.5 hours off, still air required Max.: ±0.3 dB
Humidity
(steady state) JIS C 5202 7.5 1 000 hours, 40 ±2°C, 93(+2/-3)% RH
RCWV applied for 1.5 hours on and 0.5 hour off Max.: ±0.3 dB
Moisture resistance MIL-STD-202G-
method 106F Each temperature / humidity cycle is dened at 8 hours (method
106F), 3 cycles / 24 hours for 10d with 25°C / 65°C 95% R.H Max.: ±0.3 dB
Thermal shock MIL-STD-202G-
method 107G LCT / UCT, number of cycles required is 300
Maximum transfer time is 20 seconds Max.: ±0.3 dB
Solderability Wetting IPC/JEDECJ-
STD-002B testB
Electrical test not required. Magnication 50X
Leadfree solder bath at 245 ±3°C
Dipping time: 3 ±0.5 seconds Well tinned
(≥95% covered)
Resistance to
soldering heat MIL-STD-202G-
method 210F Leadfree solder, 270°C, 10 seconds immersion time Max.: ±0.1 dB
Short time overload MIL-R-55342D-
para 4.7.5 2.5 times RCWV or maximum overload voltage which-
ever is less for 5 seconds at room temperature Max.: ±0.3 dB
Resistor Chip Selection Charts
Introduction to RF attenuator chip resistors
70
Global part number - Preferred type for ordering Yageo / Phycomp branded products
Ordering example: ATV321BR-071DB(L)
AT V 3 2 1 B R ―0 7 1 D B ( L )
Series name (code 1-2) Optional code(1/2) (code 16)
AT = RF attenuator thick lm Attenuation (code 12-15)
Size code (code 3-6) 0DB
(inch / metric) 1DB
V321 = 0404 = 1.0 x 1.0 2DB
10DB
Tolerance (code 7) 15DB
C = ±0.3dB 20DB
D = ±0.5dB
F = ±1dB Taping reel (code 10-11)
G = ± 2dB 07 = 7 inch Dia. reel
Packing style (code 8 ) T. C. R. (code 9)
R = Paper tape reel “―” = Based on spec.
(― for thick lm only)
Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process"
2. On customized label. "LFP" or specic symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request)
Phycomp world wide - Traditional type
Packing paper tape
Quantity 10 000 2350 703 11…L
Remark For last three digits, see table of Attenuation codes below
Note: L = An optional code
Phycomp CTC ordering code - Traditional type - North America
Packing paper tape
Quantity 10 000 9CV3218AXXXXX-PF3
Remark For last 9th to 13th digits, see table of Attenuation codes below
Attenuation codes Standard
Value
(dB) Tolerance
(dB) Phycomp world wide code
(12NC) Phycomp North America code
(NA code)
1 ±0.3 012 01DBC
2 ±0.3 022 02DBC
3 ±0.3 032 03DBC
4 ±0.3 042 04DBC
5 ±0.3 052 05DBC
6 ±0.5 063 06DBD
7 ±0.5 073 07DBD
8 ±0.5 083 08DBD
9 ±0.5 093 09DBD
10 ±0.5 103 10DBD
15 ±1.0 154 15DBF
20 ±2.0 205 20DBG
Resistor Chip Selection Charts
0404
71
Thick lm chip resistors
Global CTC
(Preferred) Description Size Tolerance Max.
power Resistance
range Resistor
pieces Min.
items
RC0201-R-SKE24L 0201, ±1% & ±5% , RoHS compliant, + Jumper 0201 F / J 1/20 W 10 - 1M 100 120
RC0402JR-SKE24L 0402, ±5%, RoHS compliant, + Jumper 0402 J 1/16 W 10 - 1M 100 110
RC0402FR-SKE96L 0402, ±1%, RoHS compliant, + Jumper 0402 F 1/16 W 10 - 1M 100 450
RC0603JR-SKE24L 0603, ±5%, RoHS compliant, + Jumper 0603 J 1/10 W 10 - 1M 50 110
RC0603FR-SKE96L 0603, ±1%, RoHS compliant, + Jumper 0603 F 1/10 W 10 - 1M 50 450
RC0805JR-SKE24L 0805, ±5%, RoHS compliant, + Jumper 0805 J 1/8 W 10 - 1M 50 110
RC0805FR-SKE96L 0805, ±1%, RoHS compliant, + Jumper 0805 F 1/8 W 10 - 1M 50 280
RC1206JR-SKE24L 1206, ±5%, RoHS compliant, + Jumper 1206 J 1/4 W 10 - 1M 50 110
RC1206FR-SKE96L 1206, ±1%, RoHS compliant, + Jumper 1206 F 1/4 W 10 - 1M 50 350
Thick lm array chip resistors (convex)
Global CTC
(Preferred) Description Size Tolerance Max.
power Resistance
range Resistor
pieces Min.
items
YC12X-JR-SK001L YC124 / YC122, ±5%, +Jumper, RoHS compliant,
refer to below table 0402 X 2
0402 X 4 J 1/16 W 10 - 1M 100 75
Global CTC Description Q’ty Global CTC Description Q’ty
2R - Array series 4R - Array series
YC122-JR-070RL 0404, ±5%, 1/16W 100 YC124-JR-070RL 0408, Jumper, 1/16W 100
YC122-JR-0710RL 0404, ±5%, 10R, 1/16W 100 YC124-JR-0710RL 0408, ±5%, 10R, 1/16W 100
YC122-JR-0722RL 0404, ±5%, 22R, 1/16W 100 YC124-JR-0722RL 0408, ±5%, 22R, 1/16W 100
YC122-JR-0733RL 0404, ±5%, 33R, 1/16W 100 YC124-JR-0733RL 0408, ±5%, 33R, 1/16W 100
YC122-JR-0747RL 0404, ±5%, 47R, 1/16W 100 YC124-JR-0747RL 0408, ±5%, 47R, 1/16W 100
YC122-JR-07100RL 0404, ±5%, 100R, 1/16W 100 YC124-JR-07100RL 0408, ±5%, 100R, 1/16W 100
YC122-JR-07330RL 0404, ±5%, 330R, 1/16W 100 YC124-JR-07330RL 0408, ±5%, 330R, 1/16W 100
YC122-JR-07470RL 0404, ±5%, 470R, 1/16W 100 YC124-JR-07470RL 0408, ±5%, 470R, 1/16W 100
YC122-JR-071KL 0404, ±5%, 1K, 1/16W 100 YC124-JR-071KL 0408, ±5%, 1K, 1/16W 100
YC122-JR-072K2L 0404, ±5%, 2K2, 1/16W 100 YC124-JR-072K2L 0408, ±5%, 2K2, 1/16W 100
YC122-JR-073K3L 0404, ±5%, 3K3, 1/16W 100 YC124-JR-073K3L 0408, ±5%, 3K3, 1/16W 100
YC122-JR-074K7L 0404, ±5%, 4K7, 1/16W 100 YC124-JR-074K7L 0408, ±5%, 4K7, 1/16W 100
YC122-JR-0710KL 0404, ±5%, 10K, 1/16W 100 YC124-JR-0710KL 0408, ±5%, 10K, 1/16W 100
Engineering design kit for current sensing application
Global CTC
(Preferred) Description Size Tolerance Max.
power Resistance
range Resistor
pieces Min.
items
CS0402-R-SK001L 0402 - 2512, ±1% & ±5%, RoHS compliant 0402 - 2512 F / J --- 100m - 910m 30 160
Engineering design kit for mobil application
Global CTC
(Preferred) Description Size Tolerance Max.
power Resistance
range Resistor
pieces Min.
items
MD0402-R-SK001L Chip resistors / MLCC / Attenuators, refer to below table --- --- --- --- 50 - 100 44
Global CTC Description Q’ty Global CTC Description Q’ty
Low ohmic series C - Array series
RL0805FR-070R36L 0805, ±1%, 0R36, 1/8W 50 CA0508KRNPO9BN100 0508, ±10%, 10pF, NP0, 50V 50
RL0805FR-070R4L 0805, ±1%, 0R4, 1/8W 50 CA0508KRNPO9BN150 0508, ±10%, 15pF, NP0, 50V 50
RL0805FR-070R62L 0805, ±1%, 0R62, 1/8W 50 CA0508KRNPO9BN180 0508, ±10%, 18pF, NP0, 50V 50
RL0805FR-7W0R2L 0805, ±1%, 0R2, 1/4W 50 CA0508KRNPO9BN220 0508, ±10%, 22pF, NP0, 50V 50
RL0805FR-7W0R22L 0805, ±1%, 0R22, 1/4W 50 CA0508KRNPO9BN330 0508, ±10%, 33pF, NP0, 50V 50
RL0805FR-7W0R33L 0805, ±1%, 0R33, 1/4W 50
Attenuiator series
RL0805FR-7W0R36L 0805, ±1%, 0R36, 1/4W 50 ATV321CR-071DBL 0404, ±0.3dB, 1dB 30
RL0805FR-7W0R39L 0805, ±1%, 0R39, 1/4W 50 ATV321CR-073DBL 0404, ±0.3dB, 3dB 30
RC0805FR-7W1RL 0805, ±1%, 1R, 1/4W 50 ATV321CR-075DBL 0404, ±0.3dB, 5dB 30
ATV321CR-076DBL 0404, ±0.3dB, 6dB 30
Note: Before ordering, please contact with sales force for detail of resistance
Resistor Chip Engineering Design Kits
Engineering design kits
SMD CERAMIC MILTILAYER CAPACITORS
74
Specication overview
Description TC
code Series Capacitance range Voltage range Size
Discrete
NP0
General purpose 0.22 pF to 33 nF 16 V to 25 V 0201, 0402, 0603, 0805, 1206, 1210
General purpose 0.22 pF to 390 pF 50 V 0201, 0402, 0603, 0805,
1206, 1210, 1812
Medium voltage 10 pF to 22 nF 100 V to 630 V 0603, 0805, 1206, 1210, 1808, 1812
High voltage 10 pF to 2.7 nF 1 kV, 2 kV,
3 kV, 4 kV 1206, 1210, 1808, 1812
Microwave 0.47 pF to 120 pF 50 V 0603, 0805, 1206
X7R
General purpose & High capacitance 100 pF to 22 µF 6.3 V to 50 V 0201, 0402, 0603, 0805,
1206, 1210, 1812
Medium voltage 100 pF to 470 nF 100 V to 630 V 0603, 0805, 1206, 1210, 1808, 1812
High voltage 100 pF to 33 nF 1 kV to 3 kV 1206, 1210, 1808, 1812
Low inductance 10 nF to 220 nF 10 V to 50 V 0306, 0508, 0612
X5R General purpose & High capacitance 10 nF to 100 µF 6.3 V to 50 V 0201, 0402, 0603, 0805,
1206, 1210, 1812
Y5V General purpose & High capacitance 10 nF to 47 µF 6.3 V to 50 V 0201, 0402, 0603, 0805, 1206, 1210
Safety certication
product NP0 High voltage SC type 10 pF to 1 nF X1/Y2, X2/Y3 1808, 1812
X7R High voltage SC type 150 pF to 1.5 nF X1/Y2, X2/Y3 1808, 1812
C-Arrays
NP0 4-C arrays 10 pF to 1 nF 50 V 0508, 0612
X7R 2-C arrays 10 nF to 100 nF 16 V 0405
4-C arrays 220 pF to 100 nF 16 V to 50 V 0508, 0612
Y5V 4-C arrays 10 nF to 100 nF 25 V 0508, 0612
High frequency NP0 High frequency 0.22 pF to 10 pF 50 V 0402, 0603
MLCC General Information
Specification overview
75
Case dimensions
Discrete capacitors
L2L3
L4
L1
W
Case size designation Dimensions in mm
Inch-based Metric L1W L2 / L3 min L2 / L3 max L4 min
0201 0603M 0.6 ±0.03 0.3 ±0.03 0.10 0.20 0.20
0402 1005M 1.0 ±0.05 0.5 ±0.05 0.20 0.30 0.40
0603 1608M 1.6 ±0.10 0.8 ±0.07 0.20 0.60 0.40
0805 2012M 2.0 ±0.10 1.25 ±0.10 0.25 0.75 0.55
1206 3216M 3.2 ±0.15 1.6 ±0.15 0.25 0.75 1.40
1210 3225M 3.2 ±0.20 2.5 ±0.20 0.25 0.75 1.40
1808 4520M 4.5 ±0.40 2.0 ±0.30 0.25 0.75 2.20
1812 4532M 4.5 ±0.20 3.2 ±0.20 0.25 0.75 2.20
Discrete capacitors - High voltage SC type /
L2L3
L4
L1
W
Case size designation Dimensions in mm
Inch-based Metric L1W L2 / L3 min L2 / L3 max L4 min
1808 4520M 4.8 ±0.30 2.0 ±0.30 0.25 0.75 3.20
1812 4532M 4.8 ±0.30 3.2 ±0.30 0.25 0.75 4.00
2-C arrays
T
W
F
A
B
P
L
Case size designation Demensions in mm
Inch-based Metric L W Tmin Tmax A B P
0405
(2 x 0402) 1013M
(2 x 1005) 1.37 ±0.15 1.0 ±0.15 0.5 0.7 0.36 ±0.1 0.2 ±0.1 0.64 ±0.1
4-C arrays
L
PA
T
B
W
Case size designation Dimensions in mm
Inch-based Metric L W Tmin Tmax A B P
0508
(4 x 0402) 1220M
(4 x 1005) 2.0 ±0.15 1.25 ±0.15 0.50 0.70 0.28 ±0.10 0.2 ±0.10 0.5 ±0.10
0612
(4 x 0603) 1632M
(4 x 1608) 3.2 ±0.15 1.60 ±0.15 0.70 0.90 0.4 ±0.10 0.3 ±0.20 0.8 ±0.10
Discrete capacitors - Low inductance types only
T
L2L3
L4
L1
W
Case size designation Dimensions in mm
Inch-based Metric L1W T L2 / L3 min L2 / L3 max L4 min
0306 0816M 0.8 ±0.15 1.6 ±0.20 0.50 ±0.10 0.10 0.30 0.20
0508 1220M 1.25 ±0.20 2.0 ±0.20 0.85 ±0.10 0.13 0.46 0.38
0612 1632M 1.6 ±0.20 3.2 ±0.20 0.85 ±0.10 0.13 0.46 0.50
MLCC General Information
Case dimensions
76
Global part number
Ordering example: CC0201KRX7R8BB102
C C 0 2 0 1 K R X 7 R 8 B B 1 0 2
Series name (code 1-2) Capacitance value (code 15-17)
CA = 4 x Capacitance array 102 = 1 000 pF
CB = 2 x Capacitance array (2 signicant digits+number of zeros;
CC = Multilayer chip capacitance the 3rd digit signies the multiplying
CL = Low inductance capacitance factor, and letter R is decimal point)
CM = Micro-wave capacitance 0 = x 1
CH = High frequency 1 = x 10 1
SC = Safety certication capacitance 2 = x 10 2
3 = x 10 3
Size code (code 3-6) 4 = x 10 4
0201 5 = x 10 5
0402 6 = x 10 6
0603 7 = x 10 7
0805 X X R = Special capacitance
1206 (X X: capacitance before decimal point)
1210
1808 Process code (code 14)
1812 N = NP0
0306 B = Class 2 product
0405
0508 Termination (code 13)
0612 B = Ni-Barrier
Capacitance tolerance (code 7) Rated voltage (code 12)
B = ±0.1 pF 4 = 4 V
C = ±0.25 pF 5 = 6.3 V
D = ±0.5 pF 6 = 10 V
F = ±1% 7 = 16 V
G = ±2% 8 = 25 V
J = ±5% 9 = 50 V
K = ±10% 0 = 100 V
M = ±20% A = 200 V
Z = -20% to +80% B = 500 V
C = 1 kV
Packing style (code 8) D = 2 kV
R = Paper tape reel Ø7 inch E = 3 kV
P = Paper tape reel Ø13 inch G = 35 V
K = Embossed plastic tape reel Ø7 inch H = 4 kV
F = Embossed plastic tape reel Ø13 inch S = 2.5 kV
T = X2 / Y3
TC material (code 9-11) W = X1 / Y2
NP0 Y = 250 V
X5R Z = 630 V
X7R
Y5V
MLCC General Information
Ordering Information - Global part number
77
Phycomp CTC ordering code - Noth America
Ordering example: 02012R102K8B20D
0201 2R 102 K 8 B 2 0 0
Size
code Temperature
characteristic Capacitance
(pF) Tolerance Voltage Termination Packing Marking Range identier
0201
0402
0603
0805
1206
1210
1808
1812
0306
0405
0508
0612
CG = NP0
2B = X5R
2R = X7R
2F = Y5V
102 = 1 000 pF
The third digit
signies the
multiplying factor:
8 = x 0.01
9 = x 0.1
0 = x 1
1 = x 10
2 = x 100
3 = x 1 000
4 = x 10 000
5 = x 100 000
6 = x 1 000 000
7 = x 10 000 000
B = ±0.1 pF
C = ±0.25 pF
D = ±0.5 pF
F = ±1%
G = ±2%
J = ±5%
K = ±10%
M = ±20%
Z = -20% to
+80%
5 = 6.3 V
6 = 10 V
7 = 16 V
8 = 25 V
9 = 50 V
0 = 100 V
B = 200 V
C = 250 V
D = 500 V
E = 1 kV
F = 2 kV
G = 3 kV
H = 4 kV
Z = 630 V
S = 2.5 kV
T = X2/Y3
W = X1/Y2
B = NiSn 2 = 180mm / 7” paper
3 = 330 mm / 13” paper
B = 180mm / 7” blister
F = 330 mm / 13” blister
P = Bulk case
0 = No marking 0 = Conventional
ceramic
D = Class 2 MLCC
L = Low
inductance
M = Microwave
S = Safty
certication
capacitance
MLCC General Information
Ordering information for North America
78
Thickness classes and packing quantities
Description Size
code Thickness
classication
(mm)
Quantity per reel Quantity
per
bulk case
Tape width 180 mm / 7” 330 mm / 13”
Paper Blister Paper Blister
Discrete capacitors
0201 0.3 ±0.03
8 mm
15 000 --- 50 000 --- ---
0402 0.5 ±0.05 10 000 --- 50 000 --- 50 000
0603 0.8 ±0.1 4 000 --- 15 000 --- 15 000
0805
0.6 ±0.1 4 000 --- 20 000 --- 10 000
0.85 ±0.1 4 000 --- 15 000 --- 8 000
1.25 ±0.2 --- 3 000 --- 10 000 5 000
1206
0.6 ±0.1 4 000 --- 20 000 --- ---
0.85 ±0.1 4 000 --- 15 000 --- ---
1.00 / 1.15 ±0.1 --- 3 000 --- 10 000 ---
1.25 ±0.2 --- 3 000 --- 10 000 ---
1.6 ±0.15 --- 2 500 --- 10 000 ---
1.6 ±0.2 --- 2 000 --- 10 000 ---
1210
0.6 / 0.7 ±0.1 --- 4 000 --- 15 000 ---
0.85 ±0.1 --- 4 000 --- 10 000 ---
1.15 ±0.1 --- 3 000 --- 10 000 ---
1.15 ±0.15 --- 3 000 --- 10 000 ---
1.25 ±0.2 --- 3 000 --- --- ---
1.5 ±0.1 --- 2 000 --- --- ---
1.6 / 1.9 ±0.2 --- 2 000 --- --- ---
2.0 ±0.2 --- 2 000 / 1 000 --- --- ---
2.5 ±0.2 --- 1 000 / 500 --- --- ---
1808
1.15 ±0.15
12 mm
--- 3 000 --- --- ---
1.25 ±0.2 --- 3 000 --- --- ---
1.35 ±0.15 --- 2 000 --- --- ---
1.5 ±0.1 --- 2 000 --- --- ---
1.6 ±0.2 --- 2 000 --- --- ---
2.0 ±0.2 --- 2 000 --- --- ---
1812
0.6 / 0.85 ±0.1 --- 2 000 --- --- ---
1.15 ±0.1 --- 1 500 --- --- ---
1.15 ±0.15 --- 1 500 --- --- ---
1.35 ±0.15 --- 1 000 --- --- ---
1.5 ±0.1 --- 1 000 --- --- ---
1.6 ±0.2 --- 1 000 --- --- ---
2.0 ±0.2 --- 1 000 --- --- ---
Low inductance
0306 0.5 ±0.1
8 mm
4 000 --- 15 000 --- ---
0508 0.85 ±0.1 4 000 --- 15 000 --- ---
0612 0.85 ±0.1 4 000 --- 15 000 --- ---
Arrays
0405 0.6 ±0.1 4 000 --- --- --- ---
0508 0.6 ±0.1 4 000 --- --- --- ---
0612 0.8 ±0.1 4 000 --- --- --- ---
MLCC General Information
Thickness classes and packing quantities for all series
79
NP0
General purpose
Capacitance Last 2-digit of
12NC
0201 0402 0603
25V 16V 25V 16V 25V
10 pF 23 0.5 ±0.05
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28 0.3 ±0.03
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36
120 pF 37
150 pF 38
180 pF 39
220 pF 41
270 pF 42 0.5 ±0.05
330 pF 43
390 pF 44
470 pF 45 0.8 ±0.1
560 pF 46
680 pF 47
820 pF 48
1000 pF 49
1.2 nF 51
1.5 nF 52
1.8 nF 53 0.8 ±0.1
2.2 nF 54
2.7 nF 55
3.3 nF 56
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - General purpose 16 to 25V, 0201 to 0603
80
NP0
General purpose
Capacitance Last 2-digit of
12NC
0805 1206 1210
16V 25V 16V 25V 25V
3.3 nF 56 1.25 ±0.2
3.9 nF 57
4.7 nF 58
5.6 nF 59 1.25 ±0.2
6.8 nF 61
8.2 nF 62 1.25 ±0.2
10 nF 63
12 nF 64 1.25 ±0.2 1.25 ±0.2
15 nF 65 1.6 ±0.2
18 nF 66
22 nF 67 2.0 ±0.2
27 nF 68 1.6 ±0.2
33 nF 69
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - General purpose 16 to 25V, 0805 to 1210
81
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X 1 X X X
Carrier tape Capacitance value
50 = Blister (≥ 1kV) See selection chart
22 = Blister
38 = Paper Tolerance
54 = Bulk 4 = ±2%
5 = ±5%
Voltage 6 = ±10%
78 = 16 V
91 = 25 V TC material
60 = 100 V 1 = NP0
93 = 200 V
83 = 250 V Packing
97 = 500 V 1 = 180 mm / 7” reel
98 = 630 V 5 = 330 mm / 13” reel
00 = 1 kV 4 = Bulk case
02 = 2 kV
99 = 2.5 kV Size
04 = 3 kV 8 = 0201
50 = 4 kV 7 = 0402
52 = X2 / Y3 6 = 0603
53 = X1 / Y2 0 = 0805
1 = 1206
2 = 1210
3 = 1808
4 = 1812
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 - General purpose 16 to 25V, 0201 to 1210
NP0
General purpose
Capacitance Last 3-digit of
12NC
0201 0402 0603 0805 1206 1210 1812
50V 50V 50V 50V 50V 50V 50V
0.47 pF 477 0.5 ±0.05 0.8 ±0.1 0.6 ±0.1 0.6 ±0.1
0.56 pF 567
0.68 pF 687
0.82 pF 827
1 pF 108 0.3 ±0.03
1.2 pF 128
1.5 pF 158
1.8 pF 188
2.2 pF 228
2.7 pF 278
3.3 pF 338
3.9 pF 398
4.7 pF 478
5.6 pF 568
6.8 pF 688
8.2 pF 828
10 pF 109
12 pF 129
15 pF 159
18 pF 189
22 pF 229
27 pF 279
33 pF 339
39 pF 399
47 pF 479 0.6 ±0.1
56 pF 569
68 pF 689
82 pF 829
100 pF 101
120 pF 121
150 pF 151
180 pF 181
220 pF 221
270 pF 271
330 pF 331 0.6 ±0.1
390 pF 391
470 pF 471
560 pF 561
680 pF 681
820 pF 821
1000 pF 102
1.2 nF 122 0.85 ±0.1
1.5 nF 152
1.8 nF 182
2.2 nF 222 1.25 ±0.2
2.7 nF 272
3.3 nF 332 0.85 ±0.1
3.9 nF 392
4.7 nF 472
5.6 nF 562 1.15 ±0.1
6.8 nF 682 0.85 ±0.1
8.2 nF 822
10 nF 103
82
MLCC Selection Charts
NP0 - Gerneral purpose 50V, 0201 to 1812
NP0
General purpose
Capacitance Last 3-digit of
12NC
0201 0402 0603 0805 1206 1210 1812
50V 50V 50V 50V 50V 50V 50V
12 nF 123 0.85 ±0.1
15 nF 153
18 nF 183 1.15 ±0.15
22 nF 223
Tape width 8 mm 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
83
MLCC Selection Charts
NP0 - Gerneral purpose 50V, 0201 to 1812
84
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
22 = Blister See selection chart
38 = Paper
54 = Bulk Tolerance
4 = ±0.1 pF for 0.47 pF ≤ C < 5 pF
±0.25 pF for 5 pF ≤ C < 10 pF
Voltage ±2% for C ≥ 10 pF
86 = 50 V 5 = ±0.25 pF for C < 5 pF
±0.5 pF for 5 pF ≤ C < 10 pF
Size ±5% for C ≥ 10 pF
8 = 0201 8 = ±0.1 pF for 5 pF ≤ C < 10 pF
9 = 0402 ±1% for C ≥ 10 pF
7 = 0603
1 = 0805 Packing
3 = 1206 1 = 180 mm / 7” reel
2 = 1210 7 = 330 mm / 13” reel
5 = 1812 4 = Bulk case
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 - Gerneral purpose 50V, 0201 to 1812
85
NP0
Medium voltage
Capacitance Last 2-digit of
12NC
0603 0805
100V 200V 250V 100V 200V 250V 500V
10 pF 23 0.8 ±0.1 0.8 ±0.1 0.8 ±0.1 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36
120 pF 37
150 pF 38
180 pF 39
220 pF 41 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
270 pF 42
330 pF 43
390 pF 44
470 pF 45
560 pF 46 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2
680 pF 47 0.8 ±0.1 0.8 ±0.1
820 pF 48
1000 pF 49
1.2 nF 51 0.85 ±0.1 1.25 ±0.2 1.25 ±0.2
1.5 nF 52
1.8 nF 53
2.2 nF 54 1.25 ±0.2
2.7 nF 55
3.3 nF 56
3.9 nF 57
4.7 nF 58
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - Midium voltage, 0603 / 0805
86
NP0
Medium voltage
Capacitance Last 2-digit of
12NC
1206 1210
100V 200V 250V 500V 630V 100V 200V 250V 500V 630V
10 pF 23 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1 0.8 ±0.1 1.25 ±0.2
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32 0.6 ±0.1 0.85 ±0.1
56 pF 33
68 pF 34
82 pF 35
100 pF 36
120 pF 37 1.0 ±0.1
150 pF 38
180 pF 39 1.25 ±0.2 1.25 ±0.2
220 pF 41
270 pF 42
330 pF 43
390 pF 44 1.15 ±0.1
470 pF 45
560 pF 46
680 pF 47
820 pF 48 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
1000 pF 49 1.15 ±0.15
1.2 nF 51
1.5 nF 52
1.8 nF 53 0.8 ±0.1 0.8 ±0.1 1.25 ±0.2 0.85 ±0.1 0.85 ±0.1
2.2 nF 54 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2
2.7 nF 55 1.15 ±0.15 1.15 ±0.15
3.3 nF 56 0.85 ±0.1
3.9 nF 57 1.25 ±0.2 1.25 ±0.2
4.7 nF 58
5.6 nF 59 1.15 ±0.15
6.8 nF 61 0.85 ±0.1
8.2 nF 62 0.8 ±0.1
10 nF 63
12 nF 64 1.25 ±0.2
15 nF 65
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - Midium voltage, 1206 / 1210
87
NP0
Medium voltage
Capacitance Last 2-digit of
12NC
1808 1812
100V 200V 250V 500V 630V 100V 200V 250V 500V 630V
10 pF 23 1.25 ±0.2
12 pF 24
15 pF 25
18 pF 26 1.25 ±0.2
22 pF 27 1.25 ±0.2
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36 0.85 ±0.1
120 pF 37
150 pF 38
180 pF 39
220 pF 41
270 pF 42
330 pF 43 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 0.6 ±0.1
390 pF 44
470 pF 45
560 pF 46
680 pF 47
820 pF 48 1.25 ±0.2
1000 pF 49 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 1.15 ±0.15
1.2 nF 51
1.5 nF 52
1.8 nF 53 1.25 ±0.2
2.2 nF 54 1.15 ±0.15
2.7 nF 55 1.6 ±0.2
3.3 nF 56
3.9 nF 57 0.85 ±0.1 0.85 ±0.1 1.25 ±0.2
4.7 nF 58 1.15 ±0.15 1.15 ±0.15
5.6 nF 59
6.8 nF 61
8.2 nF 62
10 nF 63
12 nF 64 0.85 ±0.1
15 nF 65
18 nF 66 1.15 ±0.15
22 nF 67
Tape width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - Midium voltage, 1808 / 1812
88
NP0
High voltage
Capacitance Last 2-digit of
12NC
1206 1210
1kV 2kV 1kV 2kV
10 pF 23 0.8 ±0.1 1.0 ±0.1 1.25 ±0.2 1.25 ±0.2
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36
120 pF 37 1.0 ±0.1 0.8 ±0.1
150 pF 38
180 pF 39
220 pF 41 1.25 ±0.2
270 pF 42
330 pF 43
390 pF 44 1.15 ±0.15
470 pF 45
560 pF 46
680 pF 47
820 pF 48
1000 pF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - High voltage, 1206 / 1210
89
NP0
High voltage
Capacitance Last 2-digit of
12NC
1808 1812
1kV 2kV 3kV 4kV 1kV 2kV 3kV 4kV
10 pF 23 1.25 ±0.2 1.25 ±0.2 1.15 ±0.15 1.5 ±0.1 1.25 ±0.2 1.15 ±0.15 1.5 ±0.1
12 pF 24
15 pF 25
18 pF 26 1.25 ±0.2
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36 0.85 ±0.1
120 pF 37
150 pF 38 1.6 ±0.2
180 pF 39 2.0 ±0.2
220 pF 41
270 pF 42 1.6 ±0.2
330 pF 43
390 pF 44
470 pF 45
560 pF 46
680 pF 47
820 pF 48
1000 pF 49 1.15 ±0.15
1.2 nF 51
1.5 nF 52
1.8 nF 53 1.25 ±0.2
2.2 nF 54
2.7 nF 55 1.6 ±0.2
Tape width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - High voltage, 1808 / 1812
90
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X 1 X X X
Carrier tape Capacitance value
50 = Blister (≥ 1kV) See selection chart
22 = Blister
38 = Paper Tolerance
54 = Bulk 4 = ±2%
5 = ±5%
Voltage 6 = ±10%
78 = 16 V
91 = 25 V TC material
60 = 100 V 1 = NP0
93 = 200 V
83 = 250 V Packing
97 = 500 V 1 = 180 mm / 7” reel
98 = 630 V 5 = 330 mm / 13” reel
00 = 1 kV 4 = Bulk case
02 = 2 kV
99 = 2.5 kV Size
04 = 3 kV 8 = 0201
50 = 4 kV 7 = 0402
52 = X2 / Y3 6 = 0603
53 = X1 / Y2 0 = 0805
1 = 1206
2 = 1210
3 = 1808
4 = 1812
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 - Midium & High voltage, 0603 to 1812
91
NP0
High frequency
Capacitance Last 2-digit of
12NC
0402 0603
50V 50V
0.47 pF 77 0.5 ±0.05 0.8 ±0.1
0.56 pF 67
0.68 pF 87
0.82 pF 27
1 pF 08
1.2 pF 28
1.5 pF 58
1.8 pF 88
2.2 pF 28
2.7 pF 78
3.3 pF 38
3.9 pF 98
4.7 pF 78
5.6 pF 68
6.8 pF 88
8.2 pF 28
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - High frequency, 0402 / 0603
92
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
22 = Blister See selection chart
38 = Paper
54 = Bulk Tolerance
4 = ±0.1 pF for 0.47 pF ≤ C < 5 pF
±0.25 pF for 5 pF ≤ C < 10 pF
Voltage ±2% for C ≥ 10 pF
84 = 50 V (for high frequency series) 5 = ±0.25 pF for C < 5 pF
±0.5 pF for 5 pF ≤ C < 10 pF
Size ±5% for C ≥ 10 pF
9 = 0402 8 = ±0.1 pF for 5 pF ≤ C < 10 pF
7 = 0603 ±1% for C ≥ 10 pF
Packing
1 = 180 mm / 7” reel
7 = 330 mm / 13” reel
4 = Bulk case
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 - High frequency, 0402 / 0603
93
NP0
Microwave
Capacitance Last 2-digit of
12NC
0603 0805 1206
50V 50V 50V
0.47 pF 05 0.8 ±0.1 0.8 ±0.1
0.56 pF 06
0.68 pF 07
0.82 pF 08
1 pF 09
1.2 pF 11
1.5 pF 12
1.8 pF 13
2.2 pF 14 0.8 ±0.1
2.7 pF 15
3.3 pF 16
3.9 pF 17
4.7 pF 18
5.6 pF 19
6.8 pF 21
8.2 pF 22
10 pF 23
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36
120 pF 37
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - Microwave, 0603 to 1206
94
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X 1 X X X
Carrier tape Capacitance value
38 = Paper See selection chart
54 = Bulk Tolerance
Size 0 = ±0.1 pF for C < 10 pF
578 = 0603 1 = ±0.25 pF for C < 10 pF
574 = 0805 2 = ±0.5 pF for 5 pF ≤ C < 10 pF
576 = 1206 3 = ±1% for C ≥ 10 pF
4 = ±2% pF for C ≥ 10 pF
Packing 5 = ±5% for C ≥ 10 pF
1 = 180 mm / 7” reel
5 = 330 mm / 13” reel
4 = Bulk case
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 - Microwave, 0603 to 1206
95
X7R
General purpose
Capacitance Last 2-digit of
12NC
0201 0402
6.3V 10V 16V 25V 6.3V 10V 16V 25V 50V
100 pF 09 0.3 ±0.03 0.5 ±0.05 0.5 ±0.05 0.5 ±0.05
150 pF 12
220 pF 14
330 pF 16 0.3 ±0.03
470 pF 18
680 pF 21
1000 pF 23
1.5 nF 25 0.3 ±0.03 0.3 ±0.03
2.2 nF 27
3.3 nF 29
4.7 nF 32
6.8 nF 34
10 nF 36
15 nF 38
22 nF 41 0.5 ±0.05 0.5 ±0.05
33 nF 43
47 nF 45
68 nF 47
100 nF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - General purpose, 0201 / 0402
96
X7R
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
0603 0805
6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V
100 pF 09 0.8 ±0.1 0.8 ±0.1 0.8 ±0.1 0.8 ±0.1
150 pF 12
220 pF 14 0.6 ±0.1
330 pF 16
470 pF 18
680 pF 21
1000 pF 23
1.5 nF 25
2.2 nF 27
3.3 nF 29
4.7 nF 32
6.8 nF 34
10 nF 36 0.6 ±0.1
15 nF 38
22 nF 41
33 nF 43 0.85 ±0.1
47 nF 45 0.6 ±0.1 0.85 ±0.1
68 nF 47
100 nF 49 0.8 ±0.1 0.85 ±0.1 0.85 ±0.1
150 nF 52 0.85 ±0.1
220 nF 54 1.25 ±0.2
330 nF 56 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2
470 nF 58
680 nF 61 1.25 ±0.2
1000 nF 63
2.2 uF 67
4.7 uF 72
10 uF 76
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - General purpose & High capacitance, 0603 / 0805
97
X7R
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
1206 1210 1812
6.3V 10V 16V 25V 50V 10V 16V 25V 50V 50V
470 pF 18 0.85 ±0.1
680 pF 21
1000 pF 23
1.5 nF 25
2.2 nF 27 0.85 ±0.1
3.3 nF 29
4.7 nF 32 0.85 ±0.1
6.8 nF 34
10 nF 36
15 nF 38
22 nF 41
33 nF 43
47 nF 45
68 nF 47 1.15 ±0.1
100 nF 49 0.85 ±0.1
150 nF 52 1.15 ±0.1 1.15 ±0.1
220 nF 54 0.85 ±0.1 0.85 ±0.1
330 nF 56 1.15 ±0.1 0.85 ±0.1
470 nF 58 1.15 ±0.1 0.85 ±0.1 1.0 ±0.1 1.15 ±0.1 1.6 ±0.2
680 nF 61 1.15 ±0.1 1.15 ±0.1 1.25 ±0.2 1.6 ±0.2
1000 nF 63 1.15 ±0.1 1.15 ±0.1 1.6 ±0.2 1.25 ±0.2 1.25 ±0.2
2.2 uF 67 1.9 ±0.2
4.7 uF 72 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.9 ±0.2 1.9 ±0.2
10 uF 76
22 uF 81 2.5 ±0.2
Tape width 8 mm 12mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - Gerneral purpose & High capacitance, 1206 to 1812
98
X7R
Medium voltage
Capacitance Last 2-digit of
12NC
0603 0805
100V 100V 200V 250V 500V
100 pF 09 0.8 ±0.1
150 pF 12 0.8 ±0.1
220 pF 14 0.6 ±0.1 0.85 ±0.1 0.85 ±0.1
330 pF 16
470 pF 18
680 pF 21
1000 pF 23
1.5 nF 25
2.2 nF 27
2.7 nF 28
3.3 nF 29
4.7 nF 32
5.6 nF 33
6.8 nF 34 1.25 ±0.2 1.25 ±0.2
10 nF 36 1.25 ±0.2
15 nF 38 0.85 ±0.1 0.8 ±0.1 0.8 ±0.1
22 nF 41 1.25 ±0.2 1.25 ±0.2
33 nF 43 1.25 ±0.2
47 nF 45
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - Midium voltage, 0603 / 0805
99
X7R
Medium voltage
Capacitance Last 2-digit of
12NC
1206 1210
100V 200V 250V 500V 630V 100V 200V 250V 500V 630V
220 pF 14 0.85 ±0.1 1.15 ±0.15 1.15 ±0.15 1.15 ±0.15 1.15 ±0.15
330 pF 16
470 pF 18 0.85 ±0.1 0.85 ±0.1
680 pF 21
820 pF 22
1000 pF 23 1.25 ±0.2
1.2 nF 24
1.5 nF 25
1.8 nF 26
2.2 nF 27 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
2.7 nF 28 1.15 ±0.15
3.3 nF 29
3.9 nF 31 1.25 ±0.2
4.7 nF 32 1.25 ±0.2
6.8 nF 34
10 nF 36 1.25 ±0.2
12 nF 37
15 nF 38
18 nF 39 1.15 ±0.15 1.15 ±0.15
22 nF 41 1.15 ±0.15 1.15 ±0.15 1.6 ±0.2
33 nF 43 1.6 ±0.2 2.0 ±0.2
47 nF 45 1.25 ±0.2 1.25 ±0.2
56 nF 46
68 nF 47 1.15 ±0.15 1.25 ±0.2 1.25 ±0.2
82 nF 48
100 nF 49
120 nF 51 1.15 ±0.1
150 nF 52
180 nF 53 1.6 ±0.2
220 nF 54 1.25 ±0.2
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - Midium voltage, 1206 / 1210
100
X7R
Medium voltage
Capacitance Last 2-digit of
12NC
1808 1812
100V 200V 250V 500V 630V 100V 200V 250V 500V 630V
1000 pF 23 1.35 ±0.15 1.35 ±0.15
1.5 nF 26
2.2 nF 28
3.3 nF 29 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 0.85 ±0.1
4.7 nF 32 1.25 ±0.2 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
6.8 nF 34 1.6 ±0.2
10 nF 36 1.15 ±0.1
15 nF 38 1.15 ±0.15 1.25 ±0.2
22 nF 41 1.25 ±0.2
33 nF 43 1.6 ±0.2
47 nF 45 1.15 ±0.15 1.15 ±0.15
68 nF 47
100 nF 49 1.15 ±0.1 1.6 ±0.2
150 nF 52
220 nF 54 1.6 ±0.2 1.6 ±0.2
330 nF 56 2.0 ±0.2 2.0 ±0.2
470 nF 58 2.0 ±0.2
Tape width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - Midium voltage, 1808 / 1812
101
X7R
High voltage
Capacitance Last 2-digit of
12NC
1206 1210
1kV 2kV 1kV 2kV
220 pF 14 1.15 ±0.15 1.25 ±0.2
330 pF 16
470 pF 18
680 pF 21
1000 pF 23 1.25 ±0.2 1.25 ±0.2
1.5 nF 25
2.2 nF 27 1.6 ±0.2
3.3 nF 29
4.7 nF 32 1.25 ±0.2
6.8 nF 34
10 nF 36
15 nF 38
22 nF 41 1.6 ±0.2
33 nF 43 2.0 ±0.2
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - High voltage, 1206 / 1210
102
X7R
High voltage
Capacitance Last 2-digit of
12NC
1808 1812
1kV 2kV 3kV 1kV 2kV 3kV
150 pF 12 1.6 ±0.2
220 pF 14 1.25 ±0.2
330 pF 16
470 pF 18 1.35 ±0.15 1.35 ±0.15
680 pF 21
1000 pF 23 2.0 ±0.2 1.35 ±0.15 1.35 ±0.15 1.6 ±0.2
1.5 nF 25 2.0 ±0.2
2.2 nF 27
3.3 nF 29
4.7 nF 32 1.25 ±0.2
6.8 nF 34 1.6 ±0.2 1.6 ±0.2
10 nF 36 2.0 ±0.2
15 nF 38 1.25 ±0.2
22 nF 41
33 nF 43 1.6 ±0.2
Tape width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - High voltage, 1808 / 1812
103
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
38 = Paper (≥10 V ) See selection chart
22 = Blister (≥10 V )
50 = Blister (6.3 V / ≥1 kV) Tolerance
55 = Paper (6.3 V / ≥1 kV) 5 = ±5%
54 = Bulk 6 = ±10%
7 = ±20%
Voltage
20 = 6.3 V TC material
24 = 10 V 5 = X7R
78 = 16 V
91 = 25 V Packing
58 = 50 V 1 = 180 mm / 7” reel
60 = 100 V 5 = 330 mm / 13” reel
93 = 200 V 4 = Bulk case
83 = 250 V
97 = 500 V
98 = 630 V
00 = 1 kV
02 = 2 kV
99 = 2.5 kV
04 = 3 kV
50 = 4 kV
Size
8 = 0201
7 = 0402
6 = 0603
0 = 0805
1 = 1206
2 = 1210
3 = 1808
4 = 1812
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
X7R - General purpose, High Capacitance, Midium & High voltage
104
X7R
Low inductance
Capacitance Last 2-digit of
12NC
10V 16V 25V 50V
0306 0508 0508 0612
10 nF 36 0.85 ±0.1 0.85 ±0.1
22 nF 41
47 nF 45
100 nF 49 0.5 ±0.1 0.85 ±0.1
220 nF 54
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - Low inductance, 0306 to 0612
105
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X 5 X X X
Carrier tape Capacitance value
55 = Paper See selection chart
Voltage Tolerance
09 = 10 V 6 = ±10%
08 = 16 V
07 = 25 V Packing
06 = 50V 1 = 180 mm / 7” reel
5 = 330 mm / 13” reel
Size
1 = 0508
2 = 0306
0 = 0612
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
X7R - Low inductance, 0306 to 0612
106
X5R
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
0201 0402
6.3V 10V 16V 6.3V 10V 16V
10 nF 36 0.3 ±0.03 0.3 ±0.03 0.3 ±0.03
100 nF 49 0.5 ±0.05 0.5 ±0.05 0.5 ±0.05
150 nF 52
220 nF 54
470 nF 58
1000 nF 63
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X5R - General purpose & High capacitance, 0201 / 0402
107
X5R
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
0603 0805
6.3V 10V 16V 25V 6.3V 10V 16V 25V
330 nF 56 0.8 ±0.1 0.8 ±0.1
470 nF 58 0.8 ±0.1 0.8 ±0.1
1000 nF 63 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2
2.2 uF 67 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
4.7 uF 72 1.25 ±0.2 1.25 ±0.2 1.25 ±0.2
10 uF 76
22 uF 81
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X5R - General purpose & High capacitance, 0603 / 0805
108
X5R
High capacitance
Capacitance Last 2-digit of
12NC
1206 1210 1812
6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V
2.2 uF 67 1.15 ±0.1 1.15 ±0.1 1.15 ±0.1
4.7 uF 72 1.15 ±0.1 1.6 ±0.2 1.9 ±0.2 1.9 ±0.2
10 uF 76 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.9 ±0.2
22 uF 81 2.0 ±0.2 2.0 ±0.2 2.5 ±0.2 2.5 ±0.2 2.5 ±0.2
47 uF 85 2.5 ±0.2
100 uF 89 3.2 ±0.3
Tape width 8 mm 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X5R - High capacitance, 1206 to 1812
109
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
50 = Blister (6.3 V) See selection chart
55 = Paper (6.3 V)
38 = Paper (≥10 V) Tolerance
22 = Blister (≥10 V) 5 = ±5%
54 = Bulk 6 = ±10%
7 = ±20%
Voltage
20 = 6.3 V TC material
24 = 10 V 3 = X5R
78 = 16 V
91 = 25 V Packing
58 = 50 V 1 = 180 mm / 7” reel
5 = 330 mm / 13” reel
Size 4 = Bulk case
8 = 0201
7 = 0402
6 = 0603
0 = 0805
1 = 1206
2 = 1210
4 = 1812
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
X5R - General purpose & High Capacitance, 0201 to 1812
110
Y5V
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
0201 0402
6.3V 25V 6.3V 10V 16V 25V
10 nF 36 0.3 ±0.03 0.5 ±0.05 0.5 ±0.05
22 nF 41
47 nF 45
100 nF 49 0.3 ±0.03 0.5 ±0.05
220 nF 54
470 nF 58
1000 nF 63 0.5 ±0.05
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
Y5V - General purpose & High capacitance, 0201 / 0402
111
Y5V
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
0603 0805
6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V
10 nF 36 0.8 ±0.1 0.8 ±0.1 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1
22 nF 41
47 nF 45
100 nF 49 0.8 ±0.1
220 nF 54 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
470 nF 58 0.8 ±0.1
1000 nF 63 1.25 ±0.2
2.2 uF 67 0.8 ±0.1 1.25 ±0.2
4.7 uF 72 1.25 ±0.2
10 uF 76 1.25 ±0.2 1.25 ±0.2
22 uF 81
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
Y5V - General purpose & High capacitance, 0603 / 0805
112
Y5V
General purpose & High capacitance
Capacitance Last 2-digit of
12NC
1206 1210
6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V
10 nF 36 0.6 ±0.1 0.6 ±0.1 0.6 ±0.1
22 nF 41
47 nF 45
100 nF 49
220 nF 54 0.6 ±0.1
470 nF 58 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1 0.85 ±0.1
1000 nF 63
2.2 uF 67 1.15 ±0.1
4.7 uF 72 1.15 ±0.1
10 uF 76 1.15 ±0.1 1.6 ±0.2 1.5 ±0.1 1.5 ±0.1 1.5 ±0.1
22 uF 81 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2
47 uF 85 2.0 ±0.2
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
Y5V - General purpose & High capacitance, 1206 / 1210
113
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X 9 X X X
Carrier tape Capacitance value
50 = Blister (6.3 V) See selection chart
55 = Paper (6.3 V)
38 = Paper Tolerance
22 = Blister 7 = ±20%
54 = Bulk 8 = -20 to +80%
Voltage Packing
20 = 6.3 V 1 = 180 mm / 7” reel
24 = 10 V 5 = 330 mm / 13” reel
78 = 16 V 4 = Bulk case
91 = 25 V
58 = 50 V Size
8 = 0201
7 = 0402
6 = 0603
0 = 0805
1 = 1206
2 = 1210
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
Y5V - General purpose & High Capacitance, 0201 to 1210
114
NP0
Capacitance Last 2-digit of
12NC
1808 1812 1808
X1/Y2 for TUV X1/Y2 for UL X1/Y2 for TUV X1/Y2 for UL X2/Y3 for TUV X2/Y3 for UL
10 pF 23 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2
12 pF 24
15 pF 25
18 pF 26
22 pF 27
27 pF 28
33 pF 29
39 pF 31
47 pF 32
56 pF 33
68 pF 34
82 pF 35
100 pF 36 2.0 ±0.2 2.0 ±0.2
120 pF 37 2.0 ±0.2 2.0 ±0.2
150 pF 38
180 pF 39 2.0 ±0.2 2.0 ±0.2
220 pF 41
270 pF 42
330 pF 43
390 pF 44
470 pF 45
560 pF 46
680 pF 47
820 pF 48
1000 pF 49
Tape Width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - High voltage SC type, 1808 / 1812
115
X7R
Capacitance Last 2-digit of
12NC
1808 1812 1808
X1/Y2 for TUV X1/Y2 for UL X1/Y2 for TUV X1/Y2 for UL X2/Y3 for TUV X2/Y3 for UL
150 pF 12 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2 1.6 ±0.2
180 pF 13
220 pF 14 1.6 ±0.2 1.6 ±0.2
270 pF 15 2.0 ±0.2 2.0 ±0.2
330 pF 16
390 pF 17 2.0 ±0.2 2.0 ±0.2
470 pF 18
560 pF 19
680 pF 21 2.0 ±0.2 2.0 ±0.2
820 pF 22
1000 pF 23
1.2 nF 24
1.5 nF 25
Tape width 12 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - High voltage SC type, 1808 / 1812
116
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
50 = Blister See selection chart
Voltage Tolerance
52 = X2/Y3 5 = ±5%
53 = X1/Y2 6 = ±10%
Size TC material
3 = 1808 1 = NP0
4 = 1812 5 = X7R
Packing
1 = 180 mm / 7” reel
5 = 330 mm / 13” reel
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 / X7R - High voltage SC type, 1808 / 1812
117
X7R
2-C arrays
Capacitance Last 2-digit of
12NC
0405
16V
10 nF 36 0.6 ±0.1
12 nF 37
15 nF 38
18 nF 39
22 nF 41
27 nF 42
33 nF 43
39 nF 44
47 nF 45
56 nF 46
68 nF 47
82 nF 48
100 nF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - 2C Arrays, 0405
118
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X 2 X X X X X
Carrier tape Capacitance value
50 = Blister See selection chart
55 = Paper Tolerance
Voltage 6 = ±10%
70 = 16 V 7 = ±20%
Packing TC material
1 = 180 mm / 7” reel 5 = X7R
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
X7R - 2C Arrays, 0405
119
NP0
4-C arrays
Capacitance Last 2-digit of
12NC
0508 0612
50V 50V
10 pF 23 0.6 ±0.1 0.8 ±0.1
15 pF 25
18 pF 26
22 pF 27
27 pF 28
47 pF 32
100 pF 36
150 pF 38
180 pF 39
220 pF 41
270 pF 42
330 pF 43
390 pF 44
470 pF 45
560 pF 46
680 pF 47
820 pF 48
1000 pF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
NP0 - 4C Arrays, 0508 / 0612
120
X7R
4-C arrays
Capacitance Last 2-digit of
12NC
0508 0612
16V 16V 25V 50V
220 pF 16 0.8 ±0.1 0.8 ±0.1
470 pF 21
1000 pF 23
2.2 nF 29
4.7 nF 32
10 nF 36 0.8 ±0.1 0.8 ±0.1
22 nF 41
47 nF 45
100 nF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
X7R - 4C Arrays, 0508 / 0612
121
Y5V
4-C arrays
Capacitance Last 2-digit of
12NC
0508 0612
25V 25V
10 nF 36 0.6 ±0.1 0.6 ±0.1
22 nF 41
47 nF 45
100 nF 49
Tape width 8 mm
Note: Values in shaded cells indicate thickness class (unit: mm)
MLCC Selection Charts
Y5V - 4C Arrays, 0508 / 0612
122
Global part number - Preferred type
Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products.
For details, please see page 76.
12NC ordering code - Phycomp branded product only
2 2 X X X X X X X X X X
Carrier tape Capacitance value
50 = Blister See selection chart
55 = Paper Tolerance
Voltage 5 = ±5%
10 = 16 V 6 = ±10%
12 = 25 V 7 = ±20%
14 = 50 V 8 = -20 to +80%
Size TC material
6 = 0612 (4 x 0603) 1 = NP0
7 = 0508 (4 x 0402) 5 = X7R
9 = Y5V
Packing
1 = 180 mm / 7” reel
Phycomp CTC ordering code - North America
Regional code for ordering Phycomp branded products. For details, please see page 77.
MLCC Selection Charts
NP0 / X7R / Y5V - 4C Arrays, 0508 / 0612
123
0201 sample kitsNP0 50 V NP0 25 V X7R 50 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1 ±0.25 pF 27 ±5% 47 ±10%
1.2 ±0.25 pF 33 ±5% 68 ±10%
1.5 ±0.25 pF 39 ±5% 100 ±10%
1.8 ±0.25 pF 47 ±5% 150 ±10%
2.2 ±0.25 pF 56 ±5% 220 ±10%
2.7 ±0.25 pF 68 ±5% 330 ±10%
3.3 ±0.25 pF 82 ±5% 470 ±10%
3.9 ±0.25 pF 100 ±5% X7R 25 V
4.7 ±0.25 pF Y5V 6.3V Capacitance (pF) Tolerance
5.6 ±0.50 pF Capacitance (pF) Tolerance 680 ±10%
6.8 ±0.50 pF 100 000 -20% to +80% 1 000 ±10%
8.2 ±0.50 pF X5R 6.3V X7R 16V
10 ±5% Capacitance (pF) Tolerance Capacitance (pF) Tolerance
12 ±5% 100 000 ±10% 1 500 ±10%
15 ±5% 2 200 ±10%
18 ±5% 3 300 ±10%
22 ±5% X7R 10 V
Capacitance (pF) Tolerance
10 000 ±10%
Note: 100 pieces per value. Ordering code 432204407111 for Phycomp brand product, CC020100000000000 for Yageo brand product
0402 sample kitsNP0 50 V Y5V 16 V X7R 50 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
0.47 ±0.25 pF 10 000 ±20% 100 ±10%
0.68 ±0.25 pF 22 000 ±20% 150 ±10%
1 ±0.25 pF 47 000 ±20% 220 ±10%
1.5 ±0.25 pF 100 000 ±20% 330 ±10%
2.2 ±0.25 pF 470 ±10%
3.3 ±0.25 pF 680 ±10%
4.7 ±0.25 pF 1 000 ±10%
6.8 ±0.50 pF 1 500 ±10%
10 ±5% 2 200 ±10%
15 ±5% 3 300 ±10%
22 ±5% X7R 25 V
33 ±5% Capacitance (pF) Tolerance
47 ±5% 4 700 ±10%
68 ±5% X7R 16 V
100 ±5% Capacitance (pF) Tolerance
150 ±5% 6 800 ±10%
220 ±5% 10 000 ±10%
15 000 ±10%
22 000 ±10%
Note: 95 pieces per value. Ordering code 432204409911 for Phycomp brand product, CC040200000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for 0201 / 0402
124
0603 sample kitsNP0 50 V NP0 25 V X7R 50 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
0.47 ±0.25 pF 1 000 ±5% 100 ±10%
0.68 ±0.25 pF 1 500 ±5% 150 ±10%
1 ±0.25 pF Y5V 50 V 220 ±10%
1.5 ±0.25 pF Capacitance (pF) Tolerance 330 ±10%
2.2 ±0.25 pF 10 000 ±20% 470 ±10%
3.3 ±0.25 pF 22 000 ±20% 680 ±10%
4.7 ±0.25 pF 47 000 ±20% 1 000 ±10%
6.8 ±0.50 pF 100 000 ±20% 1 500 ±10%
10 ±5% Y5V 16 V 2 200 ±10%
15 ±5% Capacitance (pF) Tolerance 3 300 ±10%
22 ±5% 220 000 ±20% 4 700 ±10%
33 ±5% 470 000 ±20% 6 800 ±10%
47 ±5% 10 000 ±10%
68 ±5% X7R 25 V
100 ±5% Capacitance (pF) Tolerance
150 ±5% 15 000 ±10%
220 ±5% 22 000 ±10%
330 ±5% X7R 16 V
470 ±5% Capacitance (pF) Tolerance
680 ±5% 33 000 ±10%
47 000 ±10%
68 000 ±10%
100 000 ±10%
Note: 48 pieces per value. Ordering code 432204407121 for Phycomp brand product, CC060300000000000 for Yageo brand product
0805 sample kitsNP0 50 V NP0 25 V X7R 50 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
0.47 ±0.25 pF 3 300 ±5% 220 ±10%
0.68 ±0.25 pF 4 700 ±5% 330 ±10%
1 ±0.25 pF Y5V 50 V 470 ±10%
1.5 ±0.25 pF Capacitance (pF) Tolerance 680 ±10%
2.2 ±0.25 pF 10 000 ±20% 1 000 ±10%
3.3 ±0.25 pF 22 000 ±20% 1 500 ±10%
4.7 ±0.25 pF 47 000 ±20% 2 200 ±10%
6.8 ±0.50 pF 100 000 ±20% 3 300 ±10%
10 ±5% 220 000 ±20% 4 700 ±10%
15 ±5% Y5V 16 V 6 800 ±10%
22 ±5% Capacitance (pF) Tolerance 10 000 ±10%
33 ±5% 470 000 ±20% 15 000 ±10%
47 ±5% 1 000 000 ±20% 22 000 ±10%
68 ±5% 33 000 ±10%
100 ±5% 47 000 ±10%
150 ±5% 68 000 ±10%
220 ±5% 100 000 ±10%
330 ±5% X7R 16 V
470 ±5% Capacitance (pF) Tolerance
680 ±5% 150 000 ±10%
1 000 ±5% 220 000 ±10%
1 500 ±5% 330 000 ±10%
2 200 ±5% 470 000 ±10%
Note: 48 pieces per value. Ordering code 432204407131 for Phycomp brand product, CC080500000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for 0603 / 0805
125
1206 sample kitsNP0 50 V NP0 25 V X7R 50 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
0.47 ±0.25 pF 10 000 ±5% 220 ±10%
0.68 ±0.25 pF Y5V 50 V 330 ±10%
1 ±0.25 pF Capacitance (pF) Tolerance 470 ±10%
1.5 ±0.25 pF 100 000 ±20% 680 ±10%
2.2 ±0.25 pF 220 000 ±20% 1 000 ±10%
3.3 ±0.25 pF 470 000 ±20% 1 500 ±10%
4.7 ±0.25 pF 1 000 000 ±20% 2 200 ±10%
6.8 ±0.50 pF 3 300 ±10%
10 ±5% 4 700 ±10%
15 ±5% 6 800 ±10%
22 ±5% 10 000 ±10%
33 ±5% 15 000 ±10%
47 ±5% 22 000 ±10%
68 ±5% 33 000 ±10%
100 ±5% 47 000 ±10%
150 ±5% 68 000 ±10%
220 ±5% 100 000 ±10%
330 ±5% 150 000 ±10%
470 ±5% 220 000 ±10%
680 ±5% X7R 16 V
1 000 ±5% Capacitance (pF) Tolerance
1 500 ±5% 330 000 ±10%
2 200 ±5% 470 000 ±10%
3 300 ±5% 680 000 ±10%
4 700 ±5% 1 000 000 ±10%
6 800 ±5%
Note: 48 pieces per value. Ordering code 432204407141 for Phycomp brand product, CC120600000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for 1206
126
High capacitance sample kits
X5R 0402 X7R 0603 Y5V 0402
Capacitance Rated voltage Tolerance Capacitance Rated voltage Tolerance Capacitance Rated voltage Tolerance
1 µF 6.3 V ±10% 1 µF 16 V ±10% 1 µF 6.3 V -20% to +80%
1 µF 10 V ±10% X7R 0805 1 µF 10 V -20% to +80%
2.2 µF 6.3 V ±20% Capacitance Rated voltage Tolerance Y5V 0603
X5R 0603 1 µF 25 V ±10% Capacitance Rated voltage Tolerance
Capacitance Rated voltage Tolerance 2.2 µF 16 V ±10% 1 µF 10 V -20% to +80%
1 µF 16 V ±10% 2.2 µF 25 V ±10% 1 µF 16 V -20% to +80%
1 µF 25 V ±10% X7R 1206 2.2 µF 10 V -20% to +80%
2.2 µF 6.3 V ±10% Capacitance Rated voltage Tolerance 2.2 µF 16 V -20% to +80%
2.2 µF 10 V ±10% 1 µF 25 V ±10% 4.7 µF 6.3 V -20% to +80%
2.2 µF 16 V ±10% 2.2 µF 25 V ±10% Y5V 0805
4.7 µF 6.3 V ±10% 4.7 µF 25 V ±10% Capacitance Rated voltage Tolerance
4.7 µF 10 V ±10% 10 µF 16 V ±10% 1 µF 16 V -20% to +80%
10 µF 6.3 V ±20% 10 µF 25 V ±10% 1 µF 25 V -20% to +80%
X5R 0805 1 µF 50 V -20% to +80%
Capacitance Rated voltage Tolerance 2.2 µF 16 V -20% to +80%
2.2 µF 25 V ±10% 4.7 µF 10 V -20% to +80%
4.7 µF 6.3 V ±10% 10 µF 10 V -20% to +80%
4.7 µF 10 V ±10% Y5V 1206
4.7 µF 16 V ±10% Capacitance Rated voltage Tolerance
10 µF 6.3 V ±10% 4.7 µF 16 V -20% to +80%
10 µF 10 V ±10% 10 µF 10 V -20% to +80%
10 µF 16 V ±10% 10 µF 16 V -20% to +80%
22 µF 6.3 V ±20% 22 µF 16 V -20% to +80%
X5R 1206
Capacitance Rated voltage Tolerance
4.7 µF 16 V ±10%
4.7 µF 25 V ±10%
10 µF 16 V ±10%
10 µF 25 V ±10%
22 µF 6.3 V ±20%
Note: 50 pieces per value. Ordering code 432204510001 for Phycomp brand product, CC888800000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for high capacitance series
127
High voltage sample kits for PCs segment
NP0 1808 NP0 1812
Capacitance Rated voltage Tolerance Capacitance Rated voltage Tolerance
10 pF 3 kV ±5% 10 pF 3 kV ±5%
15 pF 3 kV ±5% 15 pF 3 kV ±5%
22 pF 3 kV ±5% 22 pF 3 kV ±5%
33 pF 3 kV ±5% 33 pF 3 kV ±5%
47 pF 3 kV ±5% 47 pF 3 kV ±5%
68 pF 3 kV ±5% 68 pF 3 kV ±5%
100 pF 3 kV ±5% 100 pF 3 kV ±5%
150 pF 3 kV ±5% 150 pF 3 kV ±5%
220 pF 3 kV ±5% 220 pF 3 kV ±5%
330 pF 3 kV ±5% 330 pF 3 kV ±5%
470 pF 3 kV ±5% 470 pF 3 kV ±5%
X7R 1808 X7R 1206
Capacitance Rated voltage Tolerance Capacitance Rated voltage Tolerance
470 pF 3 kV ±10% 1 nF 2 kV ±10%
680 pF 3 kV ±10% 1.5 nF 2 kV ±10%
1 nF 3 kV ±10%
1.5 nF 3 kV ±10%
470 pF 2 kV ±10%
680 pF 2 kV ±10%
1 nF 2 kV ±10%
1.5 nF 2 kV ±10%
2.2 nF 2 kV ±10%
3.3 nF 2 kV ±10%
Note: 50 pieces per value. Ordering code 432204510011 for Phycomp brand product, HV999900000000000 for Yageo brand product
MLCC Engineering Design Kits
High voltage sample kits for PCs segment
128
High voltage sample kits for inverter segment NP0 1808
Capacitance Rated voltage Tolerance
5 pF 3 kV ±5%
10 pF 3 kV ±5%
12 pF 3 kV ±5%
15 pF 3 kV ±5%
18 pF 3 kV ±5%
22 pF 3 kV ±5%
27 pF 3 kV ±5%
33 pF 3 kV ±5%
39 pF 3 kV ±5%
47 pF 3 kV ±5%
56 pF 3 kV ±5%
68 pF 3 kV ±5%
82 pF 3 kV ±5%
100 pF 3 kV ±5%
120 pF 3 kV ±5%
150 pF 3 kV ±5%
220 pF 3 kV ±5%
330 pF 3 kV ±5%
470 pF 3 kV ±5%
Note: 50 pieces per value. Ordering code 432204510012 for Phycomp brand product, HV888800000000000 for Yageo brand product
MLCC Engineering Design Kits
High voltage sample kits for inverter segment
129
High voltage sample kits for general application
NP0 1206 X7R 1206
Capacitance Rated voltage Tolerance Capacitance Rated voltage Tolerance
10 pF 1 kV ±5% 10 nF 1 kV ±10%
100 pF 1 kV ±5% 1 nF 2 kV ±10%
1 nF 1 kV ±5% 1 nF 1 kV ±10%
10 pF 2 kV ±5% X7R 1210
100 pF 2 kV ±5% Capacitance Rated voltage Tolerance
NP0 1210 1 nF 1 kV ±10%
Capacitance Rated voltage Tolerance 10 nF 1 kV ±10%
10 pF 1 kV ±5% 1 nF 2 kV ±10%
100 pF 1 kV ±5% X7R 1808
1 nF 1 kV ±5% Capacitance Rated voltage Tolerance
10 pF 2 kV ±5% 10 nF 1 kV ±10%
100 pF 2 kV ±5% 1 nF 3 kV ±10%
NP0 1808 1 nF 1 kV ±10%
Capacitance Rated voltage Tolerance 1 nF 2 kV ±10%
10 pF 1 kV ±5% X7R 1812
100 pF 1 kV ±5% Capacitance Rated voltage Tolerance
1 nF 1 kV ±5% 10 nF 2 kV ±10%
10 pF 3 kV ±5% 1 nF 1 kV ±10%
100 pF 3 kV ±5% 10 nF 1 kV ±10%
10 pF 4 kV ±5%
10 pF 2 kV ±5%
100 pF 2 kV ±5%
NP0 1812
Capacitance Rated voltage Tolerance
10 pF 2 kV ±5%
100 pF 2 kV ±5%
1 nF 2 kV ±5%
10 pF 1 kV ±5%
100 pF 1 kV ±5%
1 nF 1 kV ±5%
10 pF 3 kV ±5%
100 pF 3 kV ±5%
10 nF 4 kV ±5%
Note: 50 pieces per value. Ordering code 432204510013 for Phycomp brand product, HV777700000000000 for Yageo brand product
MLCC Engineering Design Kits
High voltage sample kits for general application
130
High voltage sample kits for safety certication MLCCs
NP0 1808 TUV X7R 1808 TUV
Capacitance Safety cretication Tolerance Capacitance Safety cretication Tolerance
10 pF X1 / Y2 ±5% 150 pF X1 / Y2 ±10%
22 pF X1 / Y2 ±5% 220 pF X1 / Y2 ±10%
47 pF X1 / Y2 ±5% 330 pF X1 / Y2 ±10%
100 pF X1 / Y2 ±5% 470 pF X1 / Y2 ±10%
150 pF X1 / Y2 ±5% 680 pF X1 / Y2 ±10%
220 pF X1 / Y2 ±5% 1 nF X1 / Y2 ±10%
330 pF X1 / Y2 ±5% X7R 1808 UL
NP0 1808 UL Capacitance Safety cretication Tolerance
Capacitance Safety cretication Tolerance 150 pF X1 / Y2 ±10%
10 pF X1 / Y2 ±5% 220 pF X1 / Y2 ±10%
22 pF X1 / Y2 ±5% 330 pF X1 / Y2 ±10%
47 pF X1 / Y2 ±5% 470 pF X1 / Y2 ±10%
100 pF X1 / Y2 ±5% 680 pF X1 / Y2 ±10%
150 pF X1 / Y2 ±5% 1 nF X1 / Y2 ±10%
220 pF X1 / Y2 ±5% X7R 1812 TUV
330 pF X1 / Y2 ±5% Capacitance Safety cretication Tolerance
NP0 1812 TUV 220 pF X1 / Y2 ±10%
Capacitance Safety cretication Tolerance 330 pF X1 / Y2 ±10%
10 pF X1 / Y2 ±5% 470 pF X1 / Y2 ±10%
22 pF X1 / Y2 ±5% 680 pF X1 / Y2 ±10%
47 pF X1 / Y2 ±5% 1 nF X1 / Y2 ±10%
100 pF X1 / Y2 ±5% 1.5 nF X1 / Y2 ±10%
150 pF X1 / Y2 ±5% X7R 1812 UL
220 pF X1 / Y2 ±5% Capacitance Safety cretication Tolerance
330 pF X1 / Y2 ±5% 220 pF X1 / Y2 ±10%
470 pF X1 / Y2 ±5% 330 pF X1 / Y2 ±10%
NP0 1812 UL 470 pF X1 / Y2 ±10%
Capacitance Safety cretication Tolerance 680 pF X1 / Y2 ±10%
22 pF X1 / Y2 ±5% 1 nF X1 / Y2 ±10%
47 pF X1 / Y2 ±5% 1.5 nF X1 / Y2 ±10%
100 pF X1 / Y2 ±5% X7R 1808 TUV
150 pF X1 / Y2 ±5% Capacitance Safety cretication Tolerance
220 pF X1 / Y2 ±5% 470 pF X2 / Y3 ±10%
NP0 1808 TUV 680 pF X2 / Y3 ±10%
Capacitance Safety cretication Tolerance 1 nF X2 / Y3 ±10%
10 pF X2 / Y3 ±5% 1.5 nF X2 / Y3 ±10%
22 pF X2 / Y3 ±5% X7R 1808 UL
47 pF X2 / Y3 ±5% Capacitance Safety cretication Tolerance
100 pF X2 / Y3 ±5% 220 pF X2 / Y3 ±10%
150 pF X2 / Y3 ±5% 470 pF X2 / Y3 ±10%
220 pF X2 / Y3 ±5% 1 nF X2 / Y3 ±10%
NP0 1808 UL 1.5 nF X2 / Y3 ±10%
Capacitance Safety cretication Tolerance
150 pF X2 / Y3 ±5%
330 pF X2 / Y3 ±5%
680 pF X2 / Y3 ±5%
1.5 nF X2 / Y3 ±5%
Note: 50 pieces per value. Ordering code 432204510014 for Phycomp brand product, SC999900000000000 for Yageo brand product
MLCC Engineering Design Kits
High voltage sample kits for safety certification MLCCs
131
0402 high frequency sample kits NP0
Capacitance Rated voltage Tolerance
0.22 pF 50 V ±0.1 pF
0.3 pF 50 V ±0.1 pF
0.4 pF 50 V ±0.1 pF
0.5 pF 50 V ±0.1 pF
0.6 pF 50 V ±0.1 pF
0.7 pF 50 V ±0.1 pF
0.8 pF 50 V ±0.1 pF
0.9 pF 50 V ±0.1 pF
1 pF 50 V ±0.25 pF
1.2 pF 50 V ±0.25 pF
1.5 pF 50 V ±0.25 pF
1.8 pF 50 V ±0.25 pF
2.2 pF 50 V ±0.25 pF
2.7 pF 50 V ±0.25 pF
3.3 pF 50 V ±0.25 pF
3.9 pF 50 V ±0.25 pF
4.7 pF 50 V ±0.25 pF
5.6 pF 50 V ±0.5 pF
6.8 pF 50 V ±0.5 pF
8.2 pF 50 V ±0.5 pF
10 pF 50 V ±0.5 pF
Note: 50 pieces per value. Ordering code 432204409912 for Phycomp brand product, CH040200000000000 for Yageo brand product
0603 high frequency sample kits NP0
Capacitance Rated voltage Tolerance
0.22 pF 50 V ±0.1 pF
0.3 pF 50 V ±0.1 pF
0.47 pF 50 V ±0.1 pF
0.5 pF 50 V ±0.1 pF
0.6 pF 50 V ±0.1 pF
0.7 pF 50 V ±0.1 pF
0.8 pF 50 V ±0.1 pF
0.9 pF 50 V ±0.1 pF
1 pF 50 V ±0.25 pF
1.2 pF 50 V ±0.25 pF
1.5 pF 50 V ±0.25 pF
1.8 pF 50 V ±0.25 pF
2.2 pF 50 V ±0.25 pF
2.7 pF 50 V ±0.25 pF
3.3 pF 50 V ±0.25 pF
3.9 pF 50 V ±0.25 pF
4.7 pF 50 V ±0.25 pF
5.6 pF 50 V ±0.5 pF
6.8 pF 50 V ±0.5 pF
8.2 pF 50 V ±0.5 pF
10 pF 50 V ±0.5 pF
Note: 50 pieces per value. Ordering code 432204407122 for Phycomp brand product, CH060300000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for high frequency series
132
All sizes, all types, E1 series only
General purpose & High capacitance
0402
NP0 50 V X7R 50 V X7R 16 V Y5V 16 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1 ±0.25 pF 100 ±10% 10 000 ±10% 100 000 ±20%
10 ±5% 1 000 ±10%
100 ±5%
0603
NP0 50 V X7R 50 V X7R 16 V Y5V 10 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1 ±0.25 pF 100 ±10% 100 000 ±10% 1 000 000 -20% to +80%
10 ±5% 1 000 ±10%
100 ±5% 10 000 ±10%
0805
NP0 50 V X7R 50 V X7R 10 V Y5V 10 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1 ±0.25 pF 1 000 ±10% 1 000 000 ±10% 4 700 000 -20% to +80%
10 ±5% 10 000 ±10%
100 ±5% 100 000 ±10%
1 000 ±5%
1206
NP0 50 V X7R 50 V X7R 16 V Y5V 10 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1 ±0.25 pF 1 000 ±10% 1 000 000 ±10% 10 000 000 -20% to +80%
10 ±5% 10 000 ±10%
100 ±5% 100 000 ±10%
1 000 ±5%
Microwave
Size NP0 50 V
Capacitance (pF) Tolerance
0603 1 ±0.25 pF
0805 10 ±5%
1206 100 ±5%
Array (4 x 0603)
Size NP0 50 V X7R 25 V X7R 16 V
Capacitance (pF) Tolerance Capacitance (pF) Tolerance Capacitance (pF) Tolerance
0612 100 ±5% 10 000 ±10% 100 000 ±10%
1 000 ±5%
High voltage
Size NP0 3 kV X7R 1 kV
Capacitance (pF) Tolerance Capacitance (pF) Tolerance
1808 10 ±5%
1812 100 ±5% 10 000 ±10%
Note: 48 pieces per value (95 pieces for 0402 and 25 pieces for 1812). Ordering code 432204500581 for Phycomp brand product, CC999900000000000 for Yageo brand product
MLCC Engineering Design Kits
Sample kits for all sizes, all types, E1 series only
HIGH FREQUENCY PRODUCTS
134
GPS patch antenna (CP)
Dimensions
(mm) Frequency
range Band width*
(MHz) Gain*
(dBic/Max.) Polarization Axial
ratio VSWR* Temp. range
(°C) Packing
(Bulk)
12x12x2
1575±2 MHz
4 -1.5
Circular < 3 < 2.5 -40 to 125
CAN4313422021581B
12x12x4 9 -1 CAN4313422031581B
13x13x4 6 0 CAN 4313422991581B
15x15x2 5 1 CAN4313423021581B
15x15x4 8 2 CAN4313423031581B
18x18x2 5 1 CAN4313424021581B
18x18x4 10 4 CAN4313424031581B
25x25x2 10 5 CAN4313425021581B
25x25x4 20 5.5 CAN4313425031581B
Note: " * " marks that the value depends on the Yageo demoboard
GPS patch antenna (LP)
Dimensions
(mm) Frequency
range Band width*
(MHz) Gain*
(dBi/Max.) Polarization VSWR* Temp. range
(°C) Packing
(Bulk)
15x10x4 1575±2 MHz 8 1 Linear < 2.5 -40 to 125 CAN4313445011581B
16x06x4 CAN4313446011581B
Note: " * " marks that the value depends on the Yageo demoboard
GPS active module
Dimensions
(mm) Frequency
range Polarization LNA Gain*
(dB/Max.) Noise Figure*
(dB/Typical) Current Consumption
(mA/Max.) Temp. range
(°C) Packing
(Bulk)
13x13x5.5
1575±2 MHz Circular
17 1.5 5
-30 to 85
CAN4313434881581B
13x13x7.5 17 1.5 5 CAN4313434861581B
15x15x7.5 15.1 2.5 3 CAN4313434621581B
15x15x7.5 15.1 2.5 3 CAN4313435621581B
16x16x7.5 17 1.5 5 CAN4313435921581B
19x19x5.5 30 1.5 6 CAN4313437951581B
19x19x7.5 30 1.5 6 CAN4313437931581B
21x15x7.5 17 1.5 5 CAN4313435951581B
28x28x5.5 30 1.5 6 CAN4313439921581B
28x28x7.5 30 1.5 6 CAN4313439911581B
Note: " * " marks that the value depends on the Yageo demoboard
HF Product Selection Charts
GPS patch antenna and active module
135
UHF ceramic antenna
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
4x12x1.5 400-500 MHz > 20 0.5
Linear Omni-directional
< 3.0 -40 to 125 --- CAN4311129200431K
6.2x3.0x1.5 1.575 GHz 100 1 < 2.0 -55 to 125 ---- CAN4311113011582K
37.5x6.8x0.9 433 MHz > 20 0.5 < 3.0 -55 to 125 CAN4313121200431B CAN4311121200431K
460 MHz CAN4313121200461B CAN4311121200461K
490 MHz CAN4313121200491B CAN4311121200491K
TDMA ceramic antenna
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
12x1.6x4 800-900 MHz > 20 0.5 Linear Omni-directional < 2.0 -40 to 125 --- CNA4311129080871K
16.5x14x0.9 850-950 MHz > 80 -0.25 < 2.5 -55 to 125 CAN4313119000871B ---
DECT/WCDMA ceramic antenna
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
8.8x6.8x0.9 1.88-2.1 GHz > 100 2.0 Linear Omni-directional < 2.0 -55 to 125 --- CAN4311112001881K
Wimax ceramic antenna
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
10x0.6x1.2 2.3-2.7 GHz > 100 2.0 Linear Omni-directional < 3.0 -25 to 85 --- CAN4311861002371K
Dual-band WLAN ceramic antenna
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
8.7x8.0x0.9 2.45 / 5.2 GHz > 100 3.5 / 1.5 Linear Omni-directional < 2.5 -55 to 125 --- CAN4311117002521K
Dual-band ceramic antenna (900/1800 MHz)
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
21x12x0.9 880-960 MHz > 30 0.5 -1 Linear Omni-directional < 2.7 -55 to 125 CAN4313118009181B ---
1710-1880 MHz > 170 0.5 -1
Triple-band metal antenna (900/1800/1900MHz with cable / connector)
Dimensions
(mm) Frequency
range* Band width
(MHz) Gain *
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
Bulk Tape
35x6x0.4 880-960 MHz > 80 0.5-1.5 Linear Omni-directional < 3.5 -40 to 85 CAN4313330009191B ---
1850-1990 MHz > 170 1.5-2.5
Note: " * " marks that the value depends on the Yageo demoboard
HF Product Selection Charts
UHF, Dual-band and Triple-band antenna
136
Bluetooth antennna
Dimensions
(mm) Frequency
range Band width*
(MHz) Gain*
(dBi/Max.) Polarization Azimuth VSWR* Temp. range
(°C) Packing
(Tape)
2.0x1.2x1.1 2.45 GHz > 70 4
Linear Omni-
directional
< 2.5 -55 to 125 CAN4311714002454K
3.2x1.6x1.2
2.20 GHz
> 100
5< 2.5 -55 to 125
CAN4311712022453K
2.30 GHz CAN4311712032453K
2.40 GHz CAN4311712042453K
2.45 GHz CAN4311712002453K
2.50 GHz CAN4311712052453K
2.60 GHz CAN4311712062453K
2.70 GHz CAN4311712072453K
2.80 GHz CAN4311712082453K
2.90 GHz CAN4311712092453K
5.0x1.0x1.0
2.30 GHz
2.45 < 2.0 -25 to 85
CAN4311851032453K
2.40 GHz CAN4311851042453K
2.80 GHz CAN4311851052453K
3.10 GHz CAN4311851062453K
3.30 GHz CAN4311851072453K
3.70 GHz CAN4311851082453K
5.3x2.0x1.3
2.00 GHz
> 200 5.5 < 2.0 -25 to 85
CAN4311153002001K
2.10 GHz CAN4311153002101K
2.20 GHz CAN4311153002201K
2.30 GHz CAN4311153002301K
2.40 GHz CAN4311153002401K
2.45 GHz CAN4311153002451K
2.50 GHz CAN4311153002501K
7.8x3.6x0.9 2.45 GHz
> 100
4.1 < 2.5 -55 to 85 CAN4311115002451K
2.60 GHz CAN4311115002601K
2.70 GHz CAN4311115002701K
7.3x5.5x1.3
2.45 GHz
1.2 < 2.0 -55 to 125
CAN4311111002451K
2.60 GHz CAN4311111002601K
2.70 GHz CAN4311111002701K
2.80 GHz CAN4311111002801K
2.90 GHz CAN4311111002901K
8.0x1.0x1.0
2.10 GHz
3< 2.5 -55 to 125
CAN4311881012453K
2.20 GHz CAN4311881022453K
2.30 GHz CAN4311881032453K
2.45 GHz CAN4311881042453K
2.50 GHz CAN4311881052453K
2.60 GHz CAN4311881062453K
2.70 GHz CAN4311881072453K
2.80 GHz CAN4311881082453K
Note: " * " marks that the value depends on the Yageo demoboard
HF Product Selection Charts
Bluetooth antenna
137
Band Pass Filter
Dimensions
(mm) Frequency
range* Pass band
(MHz) Impedance Insertion
loss Ripple VSWR* Attenuation
(Min.) Packing
(Tape)
1.6x0.8x0.65 2.45 GHz 2400-2500
50 ohm
2.2 dB 0.5 dB
< 2.0
25 dB @ 1710-1910 MHz
CFL4111715012454K
8.5 dB @ 2100 MHz
20 dB @ 4800-5200 MHz
30 dB @ 7200-7500 MHz
2.0x1.25x0.85 2.45 GHz 2400-2500 2.0 dB 0.6 dB 40 dB @ 1000-1600 MHz CFL4111714032454K40 dB @ 4900 MHz
20 dB @ 7200 MHz
2.0x1.25x0.9 2.45 GHz 2400-2500 2.8 dB 0.5 dB
40 dB @ 1600 MHz
CFL4111714992454K
38 dB @ 3200 MHz
20 dB @ 4800 MHz
25 dB @ 7200 MHz
2.0x1.25x1.0 5 GHz 4900-5950 1.5 dB 0.6 dB 30 dB @ 1280-3000 MHz CFL4111714015004K25 dB @ 3300-4000 MHz
25 dB @ 9800-11900 MHz
2.0x1.25x0.85 5 GHz 4900-5900 2.2 dB 0.6 dB 25 dB @ 6850-7150 MHz CFL4111714035004K
20 dB @ 7500-9000 MHz
2.5x2.0x0.95 2.45 GHz 2400-2500 2.5 dB 0.6 dB
40 dB @ 880-960 MHz
CFL4111713022453K
30 dB @ 2100 MHz
30 dB @ 4800-5000 MHz
30 dB @ 7200-7500 MHz
2.5x2.0x0.95 2.45 GHz 2400-2500 1.5 dB 0.6 dB
40 dB @ 880-960 MHz
CFL4111713032453K
30 dB @ 1710-1785 MHz
30 dB @ 1850-1910 MHz
20 dB @ 4800-5000 MHz
30 dB @ 7200-7500 MHz
2.5x2.0x0.95 2.45 GHz 2400-2500 2.2 dB 0.6 dB
30 dB @ 1600 MHz
CFL4111713182453K
35 dB @ 3200 MHz
25 dB @ 4800-5000 MHz
30 dB @ 7200-7500 MHz
2.5x2.0x1.1 2.45 GHz 2400-2500 1.5 dB 0.6 dB
40 dB @ 880-960 MHz
CFL4111713052453K
30 dB @ 1710-1785 MHz
20 dB @ 1850-1910 MHz
30 dB @ 4800-5000 MHz
20 dB @ 7200-7500 MHz
2.5x2.0x1.2 2.45 GHz 2400-2500 2.5 dB 0.6 dB
20 dB @ 880-960 MHz
CFL4111713072453K
20 dB @ 2700 MHz
25 dB @ 4800-5000 MHz
25 dB @ 7200-7500 MHz
Note: " * " marks that the value depends on the Yageo demoboard
Low Pass Filter
Dimensions
(mm) Frequency
range* Pass Band
(MHz) Impedance Insertion
loss Ripple VSWR* Attenuation
(Min.) Packing
(Tape)
1.6x0.8x0.65 2.45 GHz 2400-2500
50 ohm
0.45 dB 0.6 dB < 1.5 25 dB @ 5000 MHz CFL4111715502454K
18 dB @ 7500 MHz
2.0x1.25x0.85 2.45 GHz 2400-2500 0.5 dB 0.6 dB < 1.8
27 dB @ 5000 MHz CFL4111714502454K
25 dB @ 7500 MHz
25 dB @ 10,000 MHz
2.0x1.25x0.85 3.5 GHz 3000-4000 0.5 dB 0.6 dB < 2.0 35 dB @ 6800 MHz CFL4111714503504K
30 dB @ 11,000 MHz (Ref.)
Note: " * " marks that the value depends on the Yageo demoboard
HF Product Selection Charts
Band pass filter and Low pass filter
138
Balun
Dimensions
(mm) Frequency
range* Pass band
(MHz) Impedance Insertion
loss Ripple VSWR* Amplitude
balance Phase
differential Packing
(Tape)
1.6x0.8x0.65 5 GHz 4900-5950 50/100 ohm
<
1.2 dB 0.6 dB
2.0
1.5 dB
180°±10°
CBA4711715015004K
2.0x1.25x0.80 2.45 GHz 2400-2500 50/50 ohm
<
1.0 dB 0.6 dB 2.0 dB CBA4711714002454K
50/100 ohm CBA4711714012454K
50/200 ohm CBA4711714022454K
2.0x1.25x0.80 5 GHz 4900-5900 50/100 ohm
<
1.2 dB 0.6 dB 2.0 dB CBA4711714015004K
Note: " * " marks that the value depends on the Yageo demoboard
Bluetooth balanced lter (Filter & Balun combo)
Dimensions
(mm) Frequency
range* Pass band
(MHz) Unbalanced
impedance Balanced
impedance Insertion
loss Amplitude
balance Phase
differential Attenuation
(MHz/Min.) Packing
(Tape)
2.0x1.2x0.9 2.45 GHz 2400-2500 50 ohm Conjugate
match to
CSR BC03/
04/05 series
< 3.5 dB
< 1.0 dB 180°±10°
40 dB @ 880-960
CBA4711714982454K
25 dB @ 1300-1600
35 dB @ 4800-5000
30 dB @ 7200-7500
40 dB @ 880-960
CBA4711714772454K
20 dB @ 1300-1600
35 dB @ 4800-5000
25 dB @ 7200-7500
40 dB @ 880-960
CBA4711714882454K
25 dB @ 1300-1600
35 dB @ 4800-5000
30 dB @ 7200-7500
40 dB @ 880-960
CBA4711714672454K
25 dB @ 1300-1600
30 dB @ 4800-5000
25 dB @ 7200-7500
40 dB @ 880-960
CBA4711814572454K
25 dB @ 1300-1600
35 dB @ 4800-5000
25 dB @ 7200-7500
2.5x2.0x1.2 2.45 GHz 2400-2500 50 ohm Conjugate
match to
CSR BC02/
03 series
< 3.5 dB
48 dB @ 880-960
CBA4711713932453K
48 dB @ 1710-1880
40 dB @ 1880-1990
20 dB @ 2110-2170
20 dB @ 4800-5000
20 dB @ 7200-7500
HF Product Selection Charts
Balun and Combo
139
Diplexer
Dimensions
(mm) Frequency
range Pass band
(MHz) Insertion loss VSWR Attenuation
(Min.) Packing
(Tape)
2.0x1.25x0.75
2.4 / 5 GHz
2400-2500
<
0.7 dB
<
2.0
17 dB @ 4800-6000 MHz
CFL4111714822504K
20 dB @ 7200-7500 MHz
4900-5900
<
1.6 dB 17 dB @ 1800-2500 MHz
20 dB @ 10300-10700 MHz (Ref.)
2.0x1.25x0.85 2400-2500
<
0.65 dB 20 dB @ 4800-6000 MHz
CFL4111714832504K
20 dB @ 7200-7500 MHz
4900-5900
<
1.1 dB 15 dB @ 1800-2400 MHz
20 dB @ 2400-2500 MHz
2.0x1.25x0.85
2400-2500
<
0.7 dB 20 dB @ 4900-5900 MHz CFL4111714852504K
4900-5900
<
0.9 dB 20 dB @ 2400-2500 MHz
2400-2500
<
0.6 dB 20 dB @ 4900-5900 MHz CFL4111714862504K
4900-5900
<
0.9 dB 25 dB @ 2400-2500 MHz
2.0x1.25x0.9 2400-2500
<
0.5 dB 20 dB @ 4800-6000 MHz
CFL4111714882504K
20 dB @ 7200-7500 MHz
4900-5900
<
0.9 dB 25 dB @ 1800-2500 MHz
25 dB @ 9800-11800 MHz (Ref.)
HF Product Selection Charts
Diplexer
SMD CERAMIC EMI FILTER CAPACITORS
X2Y
®
PRODUCTS
142
X5R
Size Y-Capacitor X-Capacitor Thickness
(mm) Global part number
Capacitance
(nF) Voltage rating
(V) Capacitance
(nF) Voltage rating
(V)
0603 220 10 110 20 0.60 CX 0603 MR X5R 6BB 224
330 10 165 20 0.60 CX 0603 MR X5R 6BB 334
NP0
Size Y-Capacitor X-Capacitor Thickness
(mm) Global part number
Capacitance
(nF) Voltage rating
(V) Capacitance
(nF) Voltage rating
(V)
0805 0.022 50 0.011 100 0.85 CX 0805 MR NPO 9BB 220
0.047 50 0.023 100 0.85 CX 0805 MR NPO 9BB 470
X7R
Size Y-Capacitor X-Capacitor
Thickness
(mm) Global part number
Capacitance
(nF) Voltage rating
(V) Capacitance
(nF) Voltage rating
(V)
0603
1.5 100 0.75 200
0.60
CX 0603 MR X7R 0BB 152
2.2 100 1.1 200 CX 0603 MR X7R 0BB 222
4.7 100 2.4 200 CX 0603 MR X7R 0BB 472
5.6 50 / 63 2.8 100 CX 0603 MR X7R 9BB 562
10 50 / 63 5 100 CX 0603 MR X7R 9BB 103
22 25 11 50 CX 0603 MR X7R 8BB 223
47 16 24 25 CX 0603 MR X7R 7BB 473
56 16 28 25 CX 0603 MR X7R 7BB 563
100 10 50 16 CX 0603 MR X7R 6BB 104
0805
4.7 100 2.4 200
0.85
CX 0805 MR X7R 0BB 472
10 100 5 200 CX 0805 MR X7R 0BB 103
15 50 / 63 8 100 CX 0805 MR X7R 9BB 153
18 50 / 63 9 100 CX 0805 MR X7R 9BB 183
22 25 11 50 CX 0805 MR X7R 8BB 223
39 25 20 50 CX 0805 MR X7R 8BB 393
47 16 24 25 CX 0805 MR X7R 7BB 473
100 16 50 25 CX 0805 MR X7R 7BB 104
180 10 90 16 CX 0805 MR X7R 6BB 184
1206
22 100 11 200
1.20
CX 1206 MK X7R 0BB 223
47 50 / 63 24 100 CX 1206 MK X7R 9BB 473
100 50 / 63 50 100 CX 1206 MK X7R 9BB 104
180 25 90 50 CX 1206 MK X7R 8BB 184
220 16 110 25 CX 1206 MK X7R 7BB 224
390 16 195 25 CX 1206 MK X7R 7BB 394
470 16 235 25 CX 1206 MK X7R 7BB 474
1210
47 100 24 200 1.20 CX 1210 MK X7R 0BB 473
100 50 / 63 50 100 1.20 CX 1210 MK X7R 9BB 104
220 50 / 63 110 100 1.60 CX 1210 MK X7R 9BB 224
470 25 235 50 1.60 CX 1210 MK X7R 8BB 474
560 25 280 50 1.60 CX 1210 MK X7R 8BB 564
820 16 410 25 1.60 CX 1210 MK X7R 7BB 824
1000 16 500 25 1.60 CX 1210 MK X7R 7BB 105
1410 390 50 195 100 1.30 CX 1410 MK X7R 9BB 394
Note: 1. Special values are available on request
2. Ordering codes for preferred versions (20% tolerance, 180 mm reel). For packing and tolerance information, see section "Thickness classes and packing quantities" on next page
X2Y® Product Selection Charts
SMD Ceramic EMI Filter Capacitors X2Y® series
143
Global part number
Ordering example: CX0603MKX7R6BB104
C X 0 6 0 3 M K X 7 R 6 B B 1 0 4
Series name (code 1-2) Capacitance value (code 15-17)
CX = X2Y ® series 104 = 100 000 pF
(2 signicant digits+number of zeros;
Size code (code 3-6) the 3rd digit signies the multiplying
EIA mm factor, and letter R is decimal point)
0603 (1608M) 0 = x 1
0805 (2012M) 1 = x 10 1
1206 (3216M) 2 = x 10 2
1210 (3225M) 3 = x 10 3
1410 (3625M) 4 = x 10 4
1812 (4632M) 5 = x 10 5
6 = x 10 6
Capacitance tolerance (code 7)
M = ±20% Process code (code 14)
B = BME
Packing style (code 8)
R = Paper tape reel Ø7" Termination (code 13)
K = Embossed plastic tape reel Ø7" B = Ni-barrier
TC material (code 9-11) Rated voltage (code 12)
NP0 5 = 6.3 V
X5R 7 = 16 V
X7R 8 = 25 V
9 = 50 V
0 = 100 V
Thickness classes and packing quantities
Thickness
Classication
(mm)
Quantity per reel
8 mm tape width
Ø180mm / 7”
Paper Blister
0.60 ±0.10 4 000 ---
0.85 ±0.10 4 000 ---
1.20 ±0.15 --- 2 500
1.30 ±0.20 --- 2 500
1.60 ±0.15 --- 2 500
X2Y® Product Selection Charts
Ordering information
MULTILAYER CHIP VARISTORS
146
Case dimensions
T
L4
L1
L2L3
W
Case size designation Dimensions in mm
Inch-based L1W Tmin Tmax L2 / L3 min L2 / L3 max L4 min
0402 1.0 ±0.10 0.5 ±0.10 0.45 0.55 0.15 0.30 0.40
0603 1.6 ±0.20 0.8 ±0.10 0.70 0.90 0.20 0.60 0.40
0805 2.0 ±0.10 1.25 ±0.10 0.70 0.90 0.25 0.75 0.55
1206 3.2 ±0.15 1.6 ±0.15 0.70 0.90 0.25 0.75 1.40
Size 0402
Global part number
Varistor voltage/
Breakdown voltage Max. continuous voltage/
Working voltage Clamping voltage Peak
current Resistance
R.T. (15 to 35°C ) Capacitance
@ 1 V (rms)
DC @ 1 mA D.C 8/20 µs 8/20 µs Voltage Resistance (pF)
(V) (V / Max.) (V / Max.) (A) (A / Max.) (V) (MΩ / Min.) 1 KHz 1 MHz
VRS0402MR55R651N 7.2 to 10.8 5.5 14
1
30
3
1 650 390
VRS0402SR55R601N 10 to 14 5.5 22 65 1 600 360
VRS0402MR55R331N 7.2 to 10.8 5.5 15 30 1 330 200
VRS0402MR55R201N 7.2 to 10.8 5.5 15 20 1 200 130
VRS0402MR55R101N 7.2 to 10.8 5.5 15 20 1 100 60
VRS0402SR55R101N 10 to 14 5.5 23 15 10 100 60
VRS0402SR55R820N 10 to 14 5.5 22 10 1 82 47
VRS0402SR55R680N 10 to 14 5.5 22 8 1 68 40
VRS0402SR55R500N 10 to 14 5.5 23 6 10 50 30
VRS0402SR55R330N 10 to 14 5.5 22 4 1 33 20
VRS0402SR55R220N 10 to 14 5.5 22 2 1 22 12
VRS0402SR55R100N 10 to 14 5.5 22 2 1 10 5.5
VRS0402SR55R030N 50 to 80 5.5 150 2 10 3 ---
VRS0402LR090201N 10.2 to 13.8 9 22 20 1 200 120
VRS0402KR090101N 10.2 to 13.8 9 22 20 1 100 60
VRS0402KR090500N 10.2 to 13.8 9 22 20 1 50 30
VRS0402SR090500N 11 to 17 9 25 5 1 50 30
VRS0402SR090330N 11 to 17 9 25 4 1 33 20
VRS0402LR110181N 12.75 to 17.25 11 27 20 1 180 110
VRS0402KR140161N 16.2 to 19.8 14 33 20 1 160 96
VRS0402MR140161N 14.4 to 21.6 14 33 20 1 160 96
VRS0402LR140161N 15.3 to 20.7 14 33 20 1 160 96
VRS0402SR140121N 18 to 24 14 40 20 10 120 72
VRS0402SR140101N 18 to 24 14 38 15 1 100 60
VRS0402SR140500N 18 to 24 14 38 7 1 50 30
VRS0402KR160121N 19.8 to 24.2 16 40 18 1 120 72
VRS0402SR180121N 24 to 32 18 45 20 1 120 72
VRS0402KR180900N 21.6 to 26.4 18 44 14 1 90 54
VRS0402KR180820N 21.6 to 26.4 18 45 10 1 82 50
VRS0402MR180500N 19.8 to 24.2 18 48 5 1 50 30
VRS0402SR180500N 24 to 32 18 52 5 1 50 30
VRS0402SR180400N 24 to 3s2 18 50 4 1 40 22
VRS0402SR180270N 24 to 32 18 50 4 1 27 15
VRS0402SR180150N 24 to 32 18 50 3 1 15 9
VRS0402SR180120N 24 to 32 18 46 10 10 120 72
VRS0402SR180100N 24 to 32 18 58 3 10 10 6
VRS0402SR180030N 50 to 80 18 150 2 10 3 2
VRS0402KR220820N 24.3 to 29.7 22 49 14 1 82 50
VRS0402KR260550N 29.7 to 36.3 26 60 10 1 55 33
VRS0402KR300400N 35.1 to 42.9 30 71 8 1 40 24
VRS0402SR300030N 48 to 58 30 96 2 10 3 2
MLV Product Selection Charts
Case dimensions and specification for 0402
147
Size 0603
Global part number
Varistor voltage/
Breakdown voltage Max. continuous voltage/
Working voltage Clamping voltage Peak
current Resistance
R.T. (15 to 35°C ) Capacitance
@ 1 V (rms)
DC @ 1 mA D.C 8/20 µs 8/20 µs Voltage Resistance (pF)
(V) (V / Max.) (V / Max.) (A) (A / Max.) (V) (MΩ / Min.) 1 KHz 1 MHz
VRS0603MR55R801N 7.2 to 10.8 5.5 15
1
30
3
1 800 480
VRS0603SR55R801N 10 to 14 5.5 17 30 1 800 480
VRS0603MR55R681N 7.2 to 10.8 5.5 15 30 1 680 410
VRS0603SR55R471N 10 to 14 5.5 19 30 1 470 280
VRS0603MR55R301N 7.2 to 10.8 5.5 15 30 1 300 180
VRS0603SR55R201N 10 to 14 5.5 15 30 1 200 120
VRS0603SR55R181N 10 to 14 5.5 20 30 1 180 100
VRS0603SR55R300N 10 to 14 5.5 25 10 1 30 18
VRS0603SR55R220N 11 to 17 5.5 22 5 1 22 12
VRS0603SR55R030N 50 to 80 5.5 150 3 10 3 ---
VRS0603SR070331N 10 to 14 7 22 30 1 330 200
VRS0603LR090681N 10.2 to 13.8 9 22 30 1 680 410
VRS0603MR090351N 9.6 to 14.4 9 22 30 1 350 220
VRS0603LR110481N 12.75 to 17.25 11 22 30 1 480 290
VRS0603SR120150N 24 to 32 12 55 5 10 15 9
VRS0603LR140361N 15.3 to 20.7 14 33 30 1 360 216
VRS0603SR140150N 18 to 24 14 42 5 1 15 9
VRS0603KR180301N 21.6 to 26.4 18 44 30 1 300 180
VRS0603LR180251N 20.4 to 27.6 18 42 30 0.3 250 --
VRS0603SR180121N 24 to 32 18 50 20 1 120 72
VRS0603SR180100N 90 to 160 18 225 5 1 10 6
VRS0603SR180030N 50 to 80 18 150 1 10 3 2
VRS0603KR220241N 24.3 to 29.7 22 46 30 1 240 144
VRS0603KR220101N 24.3 to 29.7 22 46 30 1 100 60
VRS0603KR260251N 29.7 to 36.3 26 58 30 1 250 160
VRS0603KR260201N 29.7 to 36.3 26 60 30 1 200 120
VRS0603KR300121N 35.1 to 42.9 30 70 30 1 120 72
VRS0603KR380101N 42.3 to 51.7 38 85 20 1 100 60
VRS0603KR450800N 50.4 to 61.6 45 100 20 1 80 48
VRS0603SR111300N 130 to 160 110 300 5 1 30 18
Size 0805
Global part number
Varistor voltage/
Breakdown voltage Max. continuous voltage/
Working voltage Clamping voltage Peak
current Leakage current
R.T. (15 to 35°C ) Capacitance
@ 1 V (rms)
DC @ 1 mA D.C 8/20 µs 8/20 µs Voltage Resistance (pF)
(V) (V / Max.) (V / Max.) (A) (A / Max.) (V) (MΩ / Min.) 1 KHz 1 MHz
VRS0805MR55R162N 6.4 to 9.6 5.5 18 180 3 1 1600 --
VRS0805KR180551N 21.6 to 26.4 18 39 100 550 --
Size 1206
Global part number
Varistor voltage/
Breakdown voltage Max. continuous voltage/
Working voltage Clamping voltage Peak
current Leakage current
R.T. (15 to 35°C ) Capacitance
@ 1 V (rms)
DC @ 1 mA D.C 8/20 µs 8/20 µs Voltage Resistance (pF)
(V) (V / Max.) (V / Max.) (A) (A / Max.) (V) (MΩ / Min.) 1 KHz 1 MHz
VRS1206LR140351N 15.3 to 20.7 14 32
1
30
3
1 350 --
VRS1206LR300401N 33.1 to 44.8 30 67 120 1 400 --
VRS1206KR560251N 61 to 77 56 110 180 10 250 150
VRS1206KR680251N 76 to 90 68 130 180 10 250 150
MLV Product Selection Charts
Specification for 0603 to 1206
148
Global part number
Ordering example: VRS0402KR55R680N
V R S 0 4 0 2 K R 5 5 R 6 8 0 N
Series name (code 1-2) Process code (code 16)
VR = Varistor N = Normal
Chip type (code 3) Capacitance value (code 13-15)
S = Single chip 680 = 68 pF
(2 signicant digits+number of zeros;
Size code (code 4-7) the 3rd digit signies the multiplying
0402 factor, and letter R is decimal point)
0603 0 = x 1
0805 1 = x 10 1
1206 Working voltage (code 10-12)
Capacitance tolerance (code 8) 55R = 5.5 V
K = ±10% 090 = 9 V
L = ±15% 110 = 11 V
M = ±20 % 150 = 15 V
S = Special range 160 = 16 V
180 = 18 V
Packing style (code 9) 220 = 22 V
R = paper tape reel Ø7 inch 260 = 26 V
300 = 30 V
380 = 38 V
450 = 45 V
560 = 56 V
680 = 68 V
111 = 110 V
Thickness classication and packing quantities
Type Thickness classication
(mm)
8 mm tape width amount per reel
180 mm / 7”
Paper
0402 0.50 ±0.05 10 000
0603 0.80 ±0.10 4 000
0805 0.80 ±0.10 4 000
1206 0.80 ±0.10 4 000
MLV Product Selection Charts
Ordering information for 0402 to 1206
Date of release: December 2008Printed in Taiwan Document order number: 2838 100 00112
©
YAGEO Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.
For more detailed and always up-to-date contact details of sales ofces, distributors and representatives, please go to our web site at
www.yageo.com
YAGEO - A GLOBAL COMPANY
ASIA
Beijing, China
Tel. +86 10 851 20810
Fax. +86 10 851 20200
Dongguan, China
Tel. +86 769 8772 0275
Fax. +86 769 8791 0053
Hong Kong, China
Tel. +852 2342 6833
Fax. +852 2342 6588
Suzhou, China
Tel. +86 512 6825 5568
Fax. +86 512 6825 5386
Tokyo, Japan
Tel. +81 3 5833 3331
Fax. +81 3 5833 3116
Kyunggi-Do, Korea
Tel. +82 31 712 4797
Fax. +82 31 712 5866
Kuala Lumpur, Malaysia
Tel. +60 3 8060 8864
Fax. +60 3 8068 2700
Singapore
Tel. +65 6244 7800
Fax. +65 6244 4943
Taipei, Taiwan
Tel. +886 2 2917 7555
Fax. +886 2 2910 9056
EUROPE
Roermond, Benelux
Tel. +31 475 385 428
Fax. +31 475 385 589
Brno, Czech Republic
Tel. +420 7 2317 5035
Fax. +420 5 4325 4936
Paris, France
Tel. +33 1 5551 8404
Fax. +33 1 5551 8407
Hamburg, Germany
Tel. +49 4121 870 189
Fax. +49 4121 870 271
Budapest, Hungary
Tel. +36 13 097 280
Fax. +36 13 097 281
Milan, Italy
Tel. +39 33 5140 9233
Fax. +39 02 2411 3051
Moscow, Russian Federation
Tel. +7 916 625 92 38
Fax. +7 495 374 81 87
Barcelona, Spain
Tel. +34 93 212 3929
Fax. +39 02 2411 3051
Croydon, UK
Tel. +44 208 781 1844
Fax. +44 208 781 1845
NORTH AMERICA
San Jose, U.S.A.
Tel. +1 408 240 6200
Fax. +1 408 240 6201
