ICS950805 Integrated Circuit Systems, Inc. Frequency Generator with 200MHz Differential CPU Clocks Recommended Application: CK-408 clock for Almador-M and Brookdale-Mobile chipsets. Programmable for group to group skew. Output Features: * 3 Differential CPU Clock Pairs (differential current mode) * 7 PCI (3.3V) @ 33.3MHz * 3 PCI_F (3.3V) @ 33.3MHz * 1 USB (3.3V) @ 48MHz * 1 DOT (3.3V) @ 48MHz * 1 REF (3.3V) @ 14.318MHz * 1 3V66 (3.3V) @ 66.6MHz * 1 VCH/3V66 (3.3V) @ 48MHz or 66.6MHz * 3 66MHz_OUT/3V66 (3.3V) @ 66.6MHz_IN or 66.6MHz * 1 66MHz_IN/3V66 (3.3V) @ Input/66MHz Features: * Almador Chipset has a DLL driving the clock buffer path for the 3 buffer path 66.6 MHz outputs, 66Buf(0:2). Almador board level designs MUST use pin 22, 66Buf_1, as the feedback connection from the clock buffer path to the Almador (GMCH) chipset. * Supports spread spectrum modulation, down spread 0 to -0.5%. * Efficient power management scheme through PD#, CPU_STOP# and PCI_STOP#. Key Specifications: * CPU Output Jitter <150ps * 3V66 Output Jitter <250ps * 66MHz Output Jitter (Buffered Mode Only) <100ps * CPU Output Skew <100ps VDDREF X1 X2 GND PCICLK_F0 PCICLK_F1 PCICLK_F2 VDDPCI GND PCICLK0 PCICLK1 PCICLK2 PCICLK3 VDDPCI GND PCICLK4 PCICLK5 PCICLK6 VDD3V66 GND 66MHz_OUT0/3V66_2 66MHz_OUT1/3V66_3 66MHz_OUT2/3V66_4 66MHz_IN/3V66_5 *PD# VDDA GND Vtt_PWRGD# * These inputs have 150K internal pull-up resistor to VDD. FS2 FS1 FS0 XTAL OSC CPU DIVDER Stop 3 3 0649H--02/25/05 PCI DIVDER Stop 7 Control Logic Config. Reg. 3V66 DIVDER 3 CPU (MHz) HzOut(2:0) 3V66(1:0) 66M 3V66(4:2) (MHz) (MHz) PCI_F PCI (MHz) 66MHzIn 3V66(5) (MHz) 0 0 0 66.66 66.66 66.66 33.33 66.66 0 0 1 100.00 66.66 66.66 33.33 66.66 3V66_5/66MHz_IN 0 1 0 200.00 66.66 66.66 33.33 66.66 3V66_3/66MHz_OUT1 0 1 1 133.33 66.66 66.66 33.33 66.66 3V66_(4,2)/66MHz_OUT(2,0) 1 0 0 66.66 66.66 66MHz_IN 66MHz_IN/2 66MHz_IN REF 1 0 1 100.00 66.66 66MHz_IN 66MHz_IN/2 66MHz_IN CPUCLKT (2:0) CPUCLKC (2:0) 1 1 0 200.00 66.66 66MHz_IN 66MHz_IN/2 66MHz_IN 1 1 1 133.33 66.66 66MHz_IN 66MHz_IN/2 66MHz_IN Mid 0 0 Tristate Tristate Tristate Tristate Tristate Mid 0 1 TCLK/2 TCLK/4 TCLK/4 TCLK/8 TCLK/4 48MHz_DOT PD# CPU_STOP# PCI_STOP# MULTSEL0 FS (2:0) SDATA SCLK REF FS1 FS0 CPU_STOP#* CPUCLKT0 CPUCLKC0 VDDCPU CPUCLKT1 CPUCLKC1 GND VDDCPU CPUCLKT2 CPUCLKC2 MULTSEL0* I REF GND FS2 48MHz_USB 48MHz_DOT VDD48 GND 3V66_1/VCH_CLK PCI_STOP#* 3V66_0 VDD3V66 GND SCLK SDATA 56-Pin 300mil SSOP 6.10 mm. Body, 0.50 mm. pitch TSSOP 48MHz_USB PLL2 PLL1 Spread Spectrum 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 Functionality Block Diagram X1 X2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ICS950805 Pin Configuration PCICLK (6:0) PCICLK_F (2:0) 66MHz_0 Mid 1 0 Reser ved Reser ved Reser ved Reser ved Reser ved 3V66_1/VCH_CLK Mid 1 1 Reser ved Reser ved Reser ved Reser ved Reser ved I REF ICS950805 Pin Configuration PIN NUMBER PIN NAME TYPE 1, 8, 14, 19, 26, 32, 37, 46, 50 VDD PWR 2 X1 X2 Cr ystal Input 3 X2 X1 Cr ystal Output 7, 6, 5 PCICLK_F (2:0) OUT Free running PCI clock not affected by PCI_STOP# for power management. 4, 9, 15, 20, 27, 31, 36, 41, 47 GND PWR Ground pins for 3.3V supply 18, 17, 16, 13, 12,11, 10 PCICLK (6:0) OUT PCI clock outputs 66MHz_OUT (2:0) OUT 66MHz buffered 66MHz_OUT from 66MHz_IN input. 66MHz reference clocks, from internal VCO 23, 22, 21 24 DESCRIPTION 3.3V power supply 14.318MHz Cr ystal input 14.318MHz Cr ystal output 3V66 (4:2) OUT 66MHz_IN IN 3V66_5 OUT PD# IN Invokes power-down mode. Active Low. 25 66MHz input to buffered 66MHz_OUT and PCI clocks 66MHz reference clock, from internal VCO 28 Vtt_PWRGD# IN This 3.3V LVTTL input is a level sensitive strobe used to determine when FS[0:2] and MULTISEL0 inputs are valid and are ready to be sampled (active low) 29 SDATA I/O Data pin for I2C circuitry 5V tolerant 30 SCLK IN Clock pin of I2C circuitry 5V tolerant 33 3V66_0 OUT 66MHz reference clocks, from internal VCO Halts PCICLK clocks at logic 0 level, when input low except PCICLK_F which are free running 34 PCI_STOP# IN 35 3V66_1/VCH_CLK OUT 38 48MHz_DOT OUT 48MHz output clock for DOT 39 48MHz_USB OUT 48MHz output clock for USB 40 FS2 IN 42 I REF OUT 43 MULTSEL0 IN 3.3V output selectable through I2C to be 66MHz from internal VCO or 48MHz (non-SSC) Special 3.3V input for Mode selection This pin establishes the reference current for the CPUCLK pairs. This pin requires a fixed precision resistor tied to ground in order to establish the appropriate current. 3.3V LVTTL input for selecting the current multiplier for CPU outputs 44, 48, 51 CPUCLKC (2:0) OUT "Complementor y" clocks of differential pair CPU outputs. These are current outputs and external resistors are required for voltage bias. 45, 49, 52 CPUCLKT (2:0) OUT "True" clocks of differential pair CPU outputs. These are current outputs and external resistors are required for voltage bias. 53 CPU_STOP# IN Halts CPUCLK clocks at logic 0 level, when input low 55, 54 FS (1:0) IN Frequency select pins 56 REF OUT 14.318MHz reference clock. Power Groups (Analog) VDDA = PLL1 VDD48 = 48MHz, PLL VDDREF = VDD for Xtal, POR (Digital) VDDPCI VDD3V66 VDDCPU 0649H--02/25/05 2 ICS950805 Truth Table CPU (MHz) 3V66 (1:0) (MHz) 66Buff (2:0) 3V66 (4:2) (MHz) 66MHz_IN/ 3V66_5 PCI_F PCI (MHz) REF0 (MHz) USB/DOT (MHz) 0 66.66 66.66 66.66 66.66 33.33 14.318 48.00 1 100.00 66.66 66.66 66.66 33.33 14.318 48.00 1 0 200.00 66.66 66.66 66.66 33.33 14.318 48.00 1 1 133.33 66.66 66.66 66.66 33.33 14.318 48.00 FS2 FS1 FS0 0 0 0 0 0 0 1 0 0 66.66 66.66 66MHz_IN Input 66MHz_IN/2 14.318 48.00 1 0 1 100.00 66.66 66MHz_IN Input 66MHz_IN/2 14.318 48.00 1 1 0 200.00 66.66 66MHz_IN Input 66MHz_IN/2 14.318 48.00 1 1 1 133.33 66.66 66MHz_IN Input 66MHz_IN/2 14.318 48.00 Mid 0 0 Tristate Tristate Tristate Tristate Tristate Tristate Tristate Mid 0 1 TCLK/2 TCLK/4 TCLK/4 TCLK/4 TCLK/8 TCLK TCLK/2 Mid 1 0 Reser ved Reser ved Reser ved Reser ved Reser ved Reser ved Reser ved Mid 1 1 Reser ved Reser ved Reser ved Reser ved Reser ved Reser ved Reser ved Maximum Allowed Current Condition Max 3.3V supply consumption Max discrete cap loads, Vdd = 3.465V All static inputs = Vdd or GND Powerdown Mode (PWRDWN# = 0) 40mA Full Active 360mA Host Swing Select Functions MULTISEL0 Board Target Trace/Term Z Reference R, Iref = VDD/(3*Rr) Output Current Voh @ Z 0 50 ohms Rr = 221 1%, Iref = 5.00mA Ioh = 4* I REF 1.0V @ 50 1 50 ohms Rr = 475 1%, Iref = 2.32mA Ioh = 6* I REF 0.7V @ 50 0649H--02/25/05 3 ICS950805 Byte 0: Control Register Bit Pin# Name PWD2 Type1 Bit 0 54 FS0 X R Bit 1 55 FS1 X R Bit 2 40 FS2 X R X R Bit 3 34 PCI_STOP#3 1 RW Bit 4 53 CPU_STOP# X R Bit 5 35 3V66_1/VCH 0 RW Bit 6 - CPU_T(2:0) 0 Bit 7 - Spread Enabled 0 RW Description Reflects the value of FS0 pin sampled on power up Reflects the value of FS1 pin sampled on power up Reflects the value of FS2 pin sampled on power up Hardware mode: Reflects the value of PCI_STOP# pin sampled on PWD Software mode: 0=PCICLK stopped 1=PCICLK not stopped Reflects the current value of the external CPU_STOP# pin VCH Select 66MHz/48MHz 0=66MHz, 1=48MHz In power down mode controls output level 0=stop high 1=stop low 0=Spread Off, 1=Spread On Byte 1: Control Register PWD2 Type1 1 RW 0=Disabled 1=Enabled4 1 RW 0=Disabled 1=Enabled4 45, 44 Name CPUCLKT0 CPUCLKC0 CPUCLKT1 CPUCLKC1 CPUCLKT2 CPUCLKC2 1 RW 0=Disabled 1=Enabled4 Bit 3 52, 51 CPUCLKT0 CPUCLKC0 0 RW Bi t 4 49, 48 CPUCLKT1 CPUCLKC1 0 RW Bit 5 45, 44 CPUCLKT2 CPUCLKC2 0 RW Bit 6 Bit 7 43 MULTSEL0 0 X R Bit Pin# Bit 0 52, 51 Bit 1 49, 48 Bit 2 Description Allow control of CPUCLKT0/C0 with asser tion of CPU_STOP# 0=Not free running 1=Free running Allow control of CPUCLKT1/C1 with asser tion of CPU_STOP# 0=Not free running 1=Free running Allow control of CPUCLKT2/C2 with asser tion of CPU_STOP# 0=Not free running 1=Free running (Reserved) Reflects the current value of MULTSEL0 Notes: 1. R= Read only RW= Read and Write 2. PWD = Power on Default 3. The purpose of this bit is to allow a system designer to implement PCI_STOP functionality in one of two ways. Wither the system designer can choose to use the externally provided PCI_STOP# pin to assert and de-assert PCI_STOP functionality via I2C Byte 0 Bit 3. In Hardware mode it is not allowed to write to the I2C Byte 0 Bit3. In Software mode it is not allowed to pull the external PCI_STOP pin low. This avoids the issues related with Hardware started and software stopped PCI_STOP conditions. The clock chip is to be operated in the Hardware or Software PCI_STOP mode ONLY, it is not allowed to mix these modes. In Hardware mode the I2C byte 0 Bit 3 is R/W and should reflect the status of the part. Whether or not the chip is in PCI_STOP mode. Functionality PCI_STOP mode should be entered when [(PCI_STOP#=0) or (I2C Byte 0 Bit 3 = 0)]. 4. For disabled clocks, they stop low for single ended clocks. Differential CPU clocks stop with CPUCLKT at high, CPUCLKC off, and external resistor termination will bring CPUCLKC low. 0649H--02/25/05 4 ICS950805 Byte 2: Control Register Bit Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Pin# 10 11 12 13 16 17 18 - Name PCICLK0 PCICLK1 PCICLK2 PCICLK3 PCICLK4 PCICLK5 PCICLK6 - PWD 1 1 1 1 1 1 1 0 Type RW RW RW RW RW RW RW - Description 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled (Reserved) Byte 3: Control Register Bit Bit 0 Bit 1 Bit 2 Pin# 5 6 7 Name PCICLK_F0 PCICLK_F1 PCICLK_F2 PWD 1 1 1 Type RW RW RW Bit 3 5 PCICLK_F0 0 RW Bi t 4 6 PCICLK_F1 0 RW Bit 5 7 PCICLK_F2 0 RW Bit 6 Bit 7 39 38 48MHz_USB 48MHz_DOT 1 1 RW RW Description 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled Allow control of PCICLK_F0 with asser tion of PCI_STOP#. 0=Free Running, 1=Not free running Allow control of PCICLK_F1 with asser tion of PCI_STOP#. 0=Free Running, 1=Not free running Allow control of PCICLK_F2 with asser tion of PCI_STOP#. 0=Free Running, 1=Not free running 0=Disabled 1=Enabled 0=Disabled 1=Enabled Byte 4: Control Register Bit Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bi t 5 Bit 6 Bi t 7 Pin# 21 22 23 24 35 33 - Name 66MHz_OUT0/3V66-2 66MHz_OUT0/3V66-3 66MHz_OUT0/3V66-4 3V66_5 3V66_1/VCH_CLK 3V66_0 - PWD 1 1 1 1 1 1 0 0 Type RW RW RW RW RW RW R R Notes: 1. R= Read only RW= Read and Write 2. PWD = Power on Default 0649H--02/25/05 5 Description 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled 0=Disabled 1=Enabled (Reserved) (Reserved) ICS950805 Byte 5: Programming Edge Rate (1 = enable, 0 = disable) Bit Bit 0 Bit 1 Bit 2 Bit 3 Pin# X X X X Name 48MHz_USB 48MHz_USB 48MHz_DOT 48MHz_DOT PWD 0 0 0 0 Type RW RW RW RW Bi t 4 X 66MHz_OUT[2:0] 0 RW Bit 5 X 66MHz_OUT[2:0] 0 RW Bit 6 Bi t 7 X X - 0 0 - PWD 1 1 1 1 1 1 1 1 Type R R R R R R R R Description USB edge rate cntrol USB edge rate cntrol DOT edge rate control DOT edge rate control Tpd 66MHz_IN to 66MHz_OUT propagation delay control Tpd 66MHz_IN to 66MHz_OUT propagation delay control (Reserved) (Reserved) Byte 6: Vendor ID Register (1 = enable, 0 = disable) Bit Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Pin# X X X X X X X X Name Vendor ID Bit0 Vendor ID Bit1 Vendor ID Bit2 Vendor ID Bit3 Revision ID Bit0 Revision ID Bit1 Revision ID Bit2 Revision ID Bit3 Notes: 1. R= Read only RW= Read and Write 2. PWD = Power on Default 0649H--02/25/05 6 Description (Reserved) (Reserved) (Reserved) (Reserved) Revision ID values will be based on individual device's revision ICS950805 Absolute Maximum Ratings Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.5 V to VDD +0.5 V Ambient Operating Temperature . . . . . . . . . . 0C to +85C Case Temperature . . . . . . . . . . . . . . . . . . . . . . 115C Storage Temperature . . . . . . . . . . . . . . . . . . . . -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-5% PARAMETER Input High Voltage Input Low Voltage Input High Current SYMBOL CONDITIONS MIN V IH 2 VSS-0.3 V IL VIN = VDD -5 I IH I IL1 VIN = 0 V; Inputs with no pull-up resistors -5 TYP MAX V DD+0.3 0.8 5 UNITS V V mA mA Input Low Current I IL2 Operating Supply Current I DD3.3OP I DD3.3OP Powerdown Current Input Frequency Pin Inductance Input Capacitance1 1 Transition time Settling time1 Clk Stabilization1 Time to first clock 1 Delay 1 I DD3.3PD Fi Lpin CIN COUT CINX Ttrans Ts TSTAB T1C t PZH,t PZL t PHZ,t PLZ VIN = 0 V; Inputs with pull-up resistors -200 CL = Full load; Select @ 100 MHz 229 230 360 CL =Full load; Select @ 133 MHz IREF=5 mA VDD = 3.3 V 220 233 360 38.1 14.318 45 Logic Inputs Output pin capacitance X1 & X2 pins To 1st crossing of target frequency From 1st crossing to 1% target frequency From VDD = 3.3 V to 1% target frequency Time to first clock Output enable delay (all outputs) Output disable delay (all outputs) 1 Guaranteed by design, not 100% tested in production. 0649H--02/25/05 7 27 36 1 1 1 mA mA 7 5 6 45 3 3 3 mA MHz nH pF pF pF ms ms ms 1.8 10 10 ms ns ns ICS950805 Electrical Characteristics - CPU TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER Current Source Output Impedance SYMBOL Output High Voltage Output Low Voltage Rise Time Fall Time V OH3 V OL3 tr3 tf3 Duty Cycle dt3 Skew tsk3 tjcyc-cyc 1 Jitter, Cycle to cycle CONDITIONS Zo1 VO = Vx IOH = -1 mA IOL = 1 mA VOL = 0.41V, VOH = 0.86V VOH = 0.86V V OL = 0.41V MIN TYP MAX UNITS 3000 2.4 measurement from differential wavefrom 0.35V to +035V VT = 50% VT = 50% W V 175 175 240 242 0.4 700 700 45 51 55 % 50 100 ps 76 150 ps ps ps 1 Guaranteed by design, not 100% tested in production. IOWT can be varied and is selectable thru the MULTSEL pin. 2 Electrical Characteristics - PCICLK Buffered Mode TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-30 pF (unless otherwise specified) PARAMETER Output Frequency Output Impedance Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time Duty Cycle Skew Jitter,cycle to cyc SYMBOL FO1 CONDITIONS RDSP11 VO = VDD*(0.5) VOH1 VOL1 IOH1 IOL1 t r11 t f11 dt11 tsk11 I OH = -1 mA MIN TYP MAX UNITS MHz 12 33 55 W 2.4 I OL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V VOL @MIN = 1.95 V, VOL @MAX = 0.4 V -33 30 VOL = 0.4 V, VOH = 2.4 V 0.5 VOH = 2.4 V, VOL = 0.4 V VT = 1.5 V VT = 1.5 V t jcyc-cyc 1 VT = 1.5 V (Additive) 1 Guaranteed by design, not 100% tested in production. 0649H--02/25/05 8 V 0.55 -33 38 V mA mA 1.29 0.5to 2 ns 0.5 1.32 0.5 to 2 ns 45 51.9 55 % 209 500 ps 60 100 ps ICS950805 Electrical Characteristics - PCICLK Un-Buffered Mode TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-30 pF (unless otherwise specified) PARAMETER Output Frequency SYMBOL FO1 Output Impedance RDSP11 Output High Voltage VOH1 Output Low Voltage Output High Current Output Low Current 1 Rise Time Fall Time Duty Cycle Skew Jitter,cycle to cyc VOL IOH1 IOL1 tr11 tf11 dt11 tsk11 t jcyc-cyc 1 CONDITIONS MIN TYP MAX UNITS MHz VO = VDD*(0.5) 12 33 55 W IOH = -1 mA 2.4 IOL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V VOL @MIN = 1.95 V, VOL @MAX = 0.4 V -33 30 VOL = 0.4 V, VOH = 2.4 V 0.5 VOH = 2.4 V, VOL = 0.4 V VT = 1.5 V V 0.55 -33 38 V mA mA 1.32 0.5to 2 ns 0.5 1.39 0.5 to 2 ns 45 52 55 % 247 500 ps 111 500 ps VT = 1.5 V VT = 1.5 V 1 Guaranteed by design, not 100% tested in production. Electrical Characteristics- 3V66 - Buffered Mode: 3V66 [1:0] 66MHz_OUT [2:0] TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-30 pF (unless otherwise specified) PARAMETER Output Frequency SYMBOL FO1 Output Impedance RDSP11 Output High Voltage V OH1 V OL1 IOH1 IOL1 tr11 tf11 dt11 Output Low Voltage Output High Current Output Low Current Rise Time Fall Time Duty Cycle Skew Jitter Skew Jitter tsk1 1 tjcyc-cyc tsk1 MIN TYP 66.66 V O = V DD*(0.5) 12 33 IOH = -1 mA 2.4 IOL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V V OL @MIN = 1.95 V, VOL @MAX = 0.4 V -33 30 V OL = 0.4 V, V OH = 2.4 V 0.5 V OH = 2.4 V, VOL = 0.4 V V T = 1.5 V 1 MAX UNITS MHz 55 W V 0.55 -33 38 V mA mA 1.44 2 ns 0.5 1.36 2 ns 45 54.6 55 % 105 250 ps V T = 1.5 V 3V66 [1:0] (Additive) 20 100 ps V T = 1.5 V 66MHz_OUT [2:0] V T = 1.5 V 66MHz_OUT [2:0] 169 250 ps 89 300 ps V T = 1.5 V 1 1 tjcyc-cyc CONDITIONS 3V66 [1:0] 1 Guaranteed by design, not 100% tested in production. 0649H--02/25/05 9 ICS950805 Electrical Characteristics - 3V66 -Un-Buffered Mode: 3V66 [5:0] TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-30 pF (unless otherwise specified) PARAMETER Output Frequency SYMBOL FO1 RDSP11 VO = VDD*(0.5) Output Impedance Duty Cycle VOH1 VOL1 IOH1 IOL1 tr11 tf11 dt11 Skew tsk11 Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time Jitter CONDITIONS IOH = -1 mA MIN TYP 66.66 MAX UNITS MHz 12 33 55 W 2.4 IOL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V VOL @MIN = 1.95 V, VOL @MAX = 0.4 V -33 30 VOL = 0.4 V, VOH = 2.4 V 0.5 VOH = 2.4 V, VOL = 0.4 V VT = 1.5 V V 0.55 -33 38 V mA mA 1.38 2 ns 0.5 1.45 2 ns 45 54.4 55 % 243 500 ps 139 300 ps VT = 1.5 V tjcyc-cyc 1 VT = 1.5 V 3V66 1 Guaranteed by design, not 100% tested in production. Electrical Characteristics - VCH, 48MHz DOT, 48MHz, USB TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER Output Frequency SYMBOL FO1 Output Impedance RDSP11 Output High Voltage V OH1 V OL1 IOH1 I OL1 t r11 t f11 t r11 t f11 dt11 dt11 Output Low Voltage Output High Current Output Low Current 48DOT Rise Time 48DOT Fall Time VCH 48 USB Rise Time VCH 48 USB Fall Time 48 DOT Duty Cycle VCH 48 USB Duty Cycle 48 DOT Jitter VCH Jitter 1 CONDITIONS MIN TYP 48 V O = VDD*(0.5) 20 48 I OH = -1 mA 2.4 I OL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V V OL @MIN = 1.95 V, V OL @MAX = 0.4 V -29 29 V OL = 0.4 V, V OH = 2.4 V 0.5 V OH = 2.4 V, VOL = 0.4 V MAX UNITS MHz 60 W V 0.4 -23 27 V mA mA 0.6 1 ns 0.5 0.8 1 ns V OL = 0.4 V, V OH = 2.4 V 1 1.2 2 ns V OH = 2.4 V, VOL = 0.4 V 1 1.3 2 ns V T = 1.5 V 45 52.8 55 % V T = 1.5 V 45 53.5 55 % 183 350 ps 223 350 ps 1 t jcyc-cyc V T = 1.5 V t jcyc-cyc 1 V T = 1.5 V Guaranteed by design, not 100% tested in production. 0649H--02/25/05 10 ICS950805 Electrical Characteristics - REF TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER Output Frequency SYMBOL FO1 Output Impedance RDSP11 Output High Voltage V OH1 V OL1 IOH1 IOL1 tr11 tf11 dt11 Output Low Voltage Output High Current Output Low Current Rise Time Fall Time Duty Cycle Jitter tjcyc-cyc CONDITIONS MIN TYP VO = VDD*(0.5) 20 48 IOH = -1 mA 2.4 IOL = 1 mA V OH@MIN = 1.0 V, V OH@MAX = 3.135 V VOL @MIN = 1.95 V, V OL @MAX = 0.4 V 1 MAX UNITS MHz 60 W V -29 29 0.4 -23 27 V mA mA VOL = 0.4 V, VOH = 2.4 V 1 1.25 2 ns VOH = 2.4 V, VOL = 0.4 V 1 1.15 2 ns 45 53 55 % 723 1000 ps VT = 1.5 V VT = 1.5 V 1 Guaranteed by design, not 100% tested in production. 0649H--02/25/05 11 ICS950805 General I2C serial interface information The information in this section assumes familiarity with I2C programming. For more information, contact ICS for an I2C programming application note. How to Write: How to Read: * * * * * * * * * * * * * * * * Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends a dummy command code ICS clock will acknowledge Controller (host) sends a dummy byte count ICS clock will acknowledge Controller (host) starts sending first byte (Byte 0) through byte 5 * ICS clock will acknowledge each byte one at a time. * Controller (host) sends a Stop bit Controller (host) will send start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the byte count Controller (host) acknowledges ICS clock sends first byte (Byte 0) through byte 6 Controller (host) will need to acknowledge each byte Controller (host) will send a stop bit How to Write: Controller (Host) Start Bit Address D2(H) ICS (Slave/Receiver) How to Read: Controller (Host) Start Bit Address D3(H) ACK Dummy Command Code ACK ICS (Slave/Receiver) ACK Byte Count Dummy Byte Count ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK Stop Bit Byte 0 Byte 0 Byte 1 Byte 1 Byte 2 Byte 2 Byte 3 Byte 3 Byte 4 Byte 4 Byte 5 Byte 5 Byte 6 Byte 6 Stop Bit Notes: 1. 2. 3. 4. 5. 6. The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification. Read-Back will support Intel PIIX4 "Block-Read" protocol. The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode) The input is operating at 3.3V logic levels. The data byte format is 8 bit bytes. To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those two bytes. The data is loaded until a Stop sequence is issued. At power-on, all registers are set to a default condition, as shown. 0649H--02/25/05 12 ICS950805 Buffered Mode - 3V66[0:1], 66MHz_IN, 66MHz_OUT[0:2] and PCI Phase Relationship All 3V66 clocks are to be in phase with each other. All 66MHz_OUT clocks are to be in phase with each other. There is NO phase relationship between the 3V66 clocks and the 66MHz_OUT and PCI clocks. In the case where 3V66_1 is configured as 48MHz VCH clock, there is no defined phase relationship between 3V66_1/VCH and other 3V66 clocks. The PCI group should lag 3V66 by the standard skew described below as Tpci. The 66MHz_IN to 66MHz_OUT delay is shown in the figure below and is specified to be within a min and max propagation value. 66MHz_IN Tpd 66MHz_OUT Tpci PCICLK_F 3V66 No Relationship Group Skews at Common Transition Edges: (Buffered Mode) GROUP 3V66 66MHz_OUT PCI 66MHz_IN 66MHz_OUT 66MHz_OUT to PCI 66MHz_OUT1 to all CLK SYMBOL CONDITIONS 3V66 3V66 (1:0) pin to pin skew 66OUT 66MHz_OUT (2:0) pin to pin skew PCI Tpd Tpci PCI_F (2:0) and PCI (6:0) pin to pin skew Propogation delay from 66MHz_IN to 66MHz_OUT (2:0) 66MHz_OUT (2:0) leads 33 MHz PCI Ts1 MIN 0 0 13 MAX UNITS 500 ps 175 ps 0 500 ps 2.5 4.5 nS 1.5 3.5 nS 400 mS 30 0649H--02/25/05 TYP 150 ICS950805 Un-Buffered Mode 3V66 & PCI Phase Relationship All 3V66 clocks are to be in pphase with each other. In the case where 3V66_1 is configured as 48MHz VCH clock, there is no defined phase relationship between 3V66_1/VCH and other 3V66 clocks. The PCI group should lag 3V66 by the standard skew described below as Tpci. 3V66 (1:0) 3V66 (4:2) 3V66_5 Tpci PCICLK_F (2:0) PCICLK (6:0) Group Skews at Common Transition Edges: (Un-Buffered Mode) GROUP 3V66 PCI 3V66 to PCI SYMBOL CONDITIONS 3V66 3V66 (5:0) pin to pin skew PCI S 3V66-PCI MIN 0 PCI_F (2:0) and PCI (6:0) pin to pin skew 3V66 (5:0) leads 33MHz PCI 1 Guarenteed by design, not 100% tested in production. 0649H--02/25/05 14 TYP MAX UNITS 500 ps 0 500 ps 1.5 3.5 ns ICS950805 Normal operation transition to Suspend State S1 Entry sequence of events: 1. Power-Down (PD#) pin is taken from a high to low to start into S1 Suspend state with digital filtering of the transition in the clock circuit. 2. The first clocks to be forced to a Stop Low power down condition are the PCI buffer output clocks after a full clock cycle. If the PCI_Stop# is low, then the free-running PCI clocks (for PCI and APIC signals) are the remaining PCI buffer clocks stopped. 3. Immediately after the PCI clocks have been stopped the 66Buf_0:2 clocks are stopped low after the next high to low transition. It will always be a sequence of PCI stopping, THEN the 66Buf clocks. 4. Following the two buffer output clocks being stopped (PCI then 66.6Buffer outputs), the remaining clocks within a short delay will transition to a stopped power-down state. The first of these driven clocks that transition to a stopped state are all of the CPU PLL clocks: the CPU and the driven 3V66 clocks. 5. After the CPU PLL clocks are stopped, the 48 MHz clocks (USB, DOT clocks) will stop low, then the REF clock 14.318 MHz clock will stop low. 6. After the clocks have all been stopped, the internal PLL stages and the Crystal oscillator will all be driven to a low power stopped condition. 7. As a note to power management calculations, please be aware that the CPU design requires that in the Power-Down (S1 mode) the CPU outputs have a differential bias voltage driving the differential input stage of the CPU in this S1 state. For this PD condition of the clock generator, the IDD_PD is running around 30 to 45 mA from having the Iref running (5 mA), the output multiplier bias generator at a 2X condition and the output current source outputs are running at a 2xIref bias level (for approx 10 mA each CPU output). This results in a higher level of Clock generator IDD_PD than in prior generations of clocks due to the CPU output differential requirements. Suspend State S1 Exit transition to normal operation sequence of events: 1. Power-Down (PD#) pin is taken from Low to High with digital filtering of the transition in the clock circuit to return to normal running operation. 2. The Crystal Oscillator and the two PLL stages are released from PD to start-up to normal operation. No clocks will operate until the Lock detect circuitry verifies the PLL has reached stable final frequency (the same as normal initial power-up). 3. The CPU PLL clocks (differential CPU outputs and the driven 3V66_(0:1) clocks are operating first as soon as the Lock detect releases the clocks. With the release of these clocks, the single 66Buf_1 buffer driven output (at pin 22) is also released from the PD stopped state (but NOT the other 66Buf0,2 and not the PCI outputs). This allows the GMCH chipset 66.6 MHz DLL stage to start operating and have an operating feedback path before the other buffer outputs are released. This change is why the requirement is made that pin 22 be the connection from the clock to the GMCH chipset. Note that along with the 66Buf_0,2 and the PCI clocks, the 48 MHz and REF (14.318 MHz) clocks are also NOT released at this point. 4. A delay is built into the clock generator that allows the CPU, driven 3V66_0,1 and the single buffer clock 66Buf_1 (at pin 22) to operate before other clocks are released. This delay is larger than 30 uS and shorter than 400 uS, and after this the other clocks are staged for a sequential release. 5. The initial clocks released after the delay are the 66Buf_0, 2 outputs. 6. After the 66Buf_0,2 clocks are released, then the PCI clocks are released. 7. It will always be the sequence of 66_1 (pin 22) released with the CPU clocks, then after the delay the remaining 66Buf_0,2 first, THEN the PCI clocks. 8. Following the 66Buf_0,2 clocks, the 48 MHz (DOT and USB clocks) and the REF (14.318MHz) clocks are released. 9. Note, the initial power-up time is the same as this PD release, the PLL will power-up and the outputs will be running within a 3 ms time point. 0649H--02/25/05 15 ICS950805 PCI_STOP# - Assertion (transition from logic "1" to logic "0") The impact of asserting the PCI_STOP# signal will be the following. All PCI[6:0] and stoppable PCI_F[2,0] clocks will latch low in their next high to low transition. The PCI_STOP# setup time tsu is 10 ns, for transitions to be recognized by the next rising edge. Assertion of PCI_STOP# Waveforms PCI_STOP# PCI_F[2:0] 33MHz PCI[6:0] 33MHz tsu CPU_STOP# - Assertion (transition from logic "1" to logic "0") The impact of asserting the CPU_STOP# pin is all CPU outputs that are set in the I2C configuration to be stoppable via assertion of CPU_STOP# are to be stopped after their next transition following the two CPU clock edge sampling as shown. The final state of the stopped CPU signals is CPUT=High and CPUC=Low. There is to be no change to the output drive current values. The CPUT will be driven high with a current value equal to (MULTSEL0) X (I REF), the CPUC signal will not be driven. Assertion of CPU_STOP# Waveforms CPU_STOP# CPUT CPUC CPU_STOP# Functionality CPU_STOP# CPUT CPUC 1 Normal Normal 0 iref * Mult Float 0649H--02/25/05 16 ICS950805 PD# - Assertion (transition from logic "1" to logic "0") When PD# is sampled low by two consecutive rising edges of CPU clock then all clock outputs except CPU clocks must be held low on their next high to low transition. CPU clocks must be held with the CPU clock pin driven high with a value of 2x Iref, and CPUC undriven. Note the example below shows CPU = 100MHz, this diagram and description is applicable for all valid CPU frequencies 66, 100, 133, 200MHz. Due to the state of the internal logic, stopping and holding the REF clock outputs in the LOW state may require more than one clock cycle to complete. Power Down Assertion of Waveforms - Buffered Mode 25ns 0ns 50ns PD# CPUT 100MHz CPUC 100MHz 3V66MHz 66MHz_IN 66MHz_OUT PCI 33MHz USB 48MHz REF 14.318MHz PD# Functionality CPU_STOP# CPUT CPUC 3V66 66MHz_OUT PCICLK_F PCICLK PCICLK USB/DOT 48MHz 1 Normal Normal 66MHz 66MHz_IN 66MHz_IN 66MHz_IN 48MHz 0 iref * Mult Float Low Low Low Low Low 0649H--02/25/05 17 ICS950805 c N SYMBOL L E1 INDEX AREA A A1 b c D E E1 e h L N E 1 2 h x 45 D A A1 -Ce N SEATING PLANE b 56 .10 (.004) C In Millimeters COMMON DIMENSIONS MIN MAX 2.41 2.80 0.20 0.40 0.20 0.34 0.13 0.25 SEE VARIATIONS 10.03 10.68 7.40 7.60 0.635 BASIC 0.38 0.64 0.50 1.02 SEE VARIATIONS 0 8 VARIATIONS D mm. MIN MAX 18.31 18.55 In Inches COMMON DIMENSIONS MIN MAX .095 .110 .008 .016 .008 .0135 .005 .010 SEE VARIATIONS .395 .420 .291 .299 0.025 BASIC .015 .025 .020 .040 SEE VARIATIONS 0 8 D (inch) MIN .720 Reference Doc.: JEDEC Publication 95, MO-118 10-0034 300 mil SSOP Package Ordering Information ICS950805yFLF-T Example: ICS XXXX y F LF - PPP - T Designation for tape and reel packaging Pattern Number (2 or 3 digit number for parts with ROM code patterns) Annealed Lead Free (optional) Package Type F=SSOP Revision Designator (will not correlate with datasheet revision) Device Type Prefix ICS, AV = Standard Device 0649H--02/25/05 18 MAX .730 ICS950805 c N In Millimeters In Inches SYMBOL COMMON DIMENSIONS COMMON DIMENSIONS MIN MAX MIN MAX A -1.20 -.047 A1 0.05 0.15 .002 .006 A2 0.80 1.05 .032 .041 b 0.17 0.27 .007 .011 c 0.09 0.20 .0035 .008 D SEE VARIATIONS SEE VARIATIONS E 8.10 BASIC 0.319 BASIC E1 6.00 6.20 .236 .244 e 0.50 BASIC 0.020 BASIC L 0.45 0.75 .018 .030 N SEE VARIATIONS SEE VARIATIONS 0 8 0 8 aaa -0.10 -.004 L E1 INDEX AREA E 1 2 a D A A2 A1 VARIATIONS -Ce b N SEATING PLANE 56 aaa C D mm. MIN 13.90 D (inch) MAX 14.10 MIN .547 MAX .555 Reference Doc.: JEDEC Publication 95, MO-153 10-0039 6.10 mm. Body, 0.50 mm. pitch TSSOP (0.020 mil) (240 mil) Ordering Information ICS950805yFLF-T Example: ICS XXXX y G LF - PPP - T Designation for tape and reel packaging Pattern Number (2 or 3 digit number for parts with ROM code patterns) Annealed Lead Free (optional) Package Type G=TSSOP Revision Designator (will not correlate with datasheet revision) Device Type Prefix ICS, AV = Standard Device 0649H--02/25/05 19 ICS950805 Revision History Rev. H Issue Date Description 2/25/2005 Added Lead Free Ordering Information 0649H--02/25/05 20 Page # 18-19