EAPSV3224A0 - EVERLIGHT ELECTRONICS

1

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

Technical Data Sheet

1.6mm Round Subminiature Side Looking Phototransiator

EAPSV3224A0

Features

․Fast response time

․High photo sensitivity

․Small junction capacitance

․Package in 8mm tape on 7” diameter reels.

․Pb free

․The product itself will remain within RoHS compliant version.

․Compliance with EU REACH.

․Compliance Halogen Free .(Br <900 ppm ,Cl <900 ppm , Br+Cl < 1500 ppm)

Description

․EAPSV3224A0 is a phototransistor in miniature SMD package which is molded in a black with

spherical top view lens. The device is Spectrally matched to infrared emitting diode.

Applications

․Miniature switch

․Counters and sorter

․Position sensor

․Infrared applied system

Device Selection Guide

Device No.

Chip Material

Lens Color

EAPSV3224A0

Silicon

Black

DATASHEET

EAPSV3224A0

2

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

Recommended Soldering Pattern

for Side Looker

Collector

Emitter

Package Dimensions

Notes: 1.All dimensions are in millimeters

2.Tolerances unless dimensions ±0.1mm

Absolute Maximum Ratings (Ta=25℃)

Parameter

Symbol

Rating

Unit

Collector-Emitter Voltage

VCEO

30

V

Emitter-Collector-Voltage

VECO

5

V

Collector Current

IC

20

mA

Operating Temperature

Topr

-25 ~ +85

℃

Storage Temperature

Tstg

-40 ~ +100

℃

Soldering Temperature *1

Tsol

260

℃

Power Dissipation at(or below)

25℃Free Air Temperature

Pc

75

mW

Notes: *1:Soldering time≦5 seconds.

DATASHEET

EAPSV3224A0

3

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

Electro-Optical Characteristics (Ta=25℃)

Rankings

Rank

Symbol

Min

Max

Unit

Test Condition

BIN4

IC(ON)

1.14

2.60

mA

VCE=5V

Ee=1mW/cm2

λP =940nm

BIN5

1.77

3.61

BIN6

2.67

5.07

BIN7

3.54

7.07

BIN8

5.00

10.00

Parameter

Symbol

Min.

Typ.

Max.

Unit

Condition

Rang Of Spectral Bandwidth

λ0.5

730

---

1100

nm

---

Wavelength Of Peak Sensitivity

λP

---

940

---

nm

---

Collector-Emitter Breakdown

Voltage

BVCEO

60

---

V

IC=500μA

Ee=0mW/cm2

Emitter-Collector Breakdown

Voltage

BVECO

7

---

V

IE=50μA

Ee=0mW/cm2

Collector-Emitter Saturation

Voltage

VCE(sat)

---

0.4

V

IC=5mA

Ee=1mW/cm2

Collector Dark Current

ICEO

---

100

nA

VCE=20V

Ee=0mW/cm2

On State Collector Current

IC(ON)

---

1.0

---

mA

VCE=5V

Ee=1mW /cm2

λP =940nm

Rise Time

tr

---

15

---

μS

VCE=5V

IC=1mA

RL=1000Ω

Fall Time

tf

---

15

---

DATASHEET

EAPSV3224A0

4

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

0-25

20

40

50

025 8575 100

60

80

100

600 700 800 900 1000 1100

0

20

40

60

80

100

Relative Response (%)

Wavelength λ (nm)

Spectral Response (Ta=25℃)

-40 -20 0 20 40 60 80 100

0.01

0.1

1

10

100

1000

Vce=10V

Dark Current Iceo (nA)

Ambient Temperature Ta (℃)

0.01 0.1 1

10-2

10-1

100

101

VCE=5V

λP=940nm

Ta=25℃

On State Collector Current(mA)

Ee(mW/cm2)

Typical Electrical/Optical/Characteristics Curves

Collector Power Dissipation vs. Ambient Temperature

Spectral Sensitivity

Collector Dark Current vs. Ambient Temperature

Collector Current vs. Irradiance

DATASHEET

EAPSV3224A0

5

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

0.1 1 10

1

10

100

1000

Vce=5V,IC(on)=1mA

Ta=25℃

Switching Time t (μs)

Load Resistance RL (K)

tf

tr

Switching Time vs. Load Resistance

DATASHEET

EAPSV3224A0

6

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

 Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for Min 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

DATASHEET

EAPSV3224A0

7

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

4. Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within

once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering

of each terminal. Be careful because the damage of the product is often started at the time of the hand

solder.

5. Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a

double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the

characteristics of the LEDs will or will not be damaged by repairing.

DATASHEET

EAPSV3224A0

8

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

Collector

Emitter

Package Dimensions

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

2. Carrier Tape Dimensions:(Quantity: 1500pcs/reel)

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

DATASHEET

EAPSV3224A0

9

Issue No: XXXXXXXXXX Rev.0.1

www.everlightamericas.com

Packing Procedure

Aluminum moistue-proof bag LabelDesiccant

Label

Label Form Specification

CPN: Customer’s Production Number

P/N : Production Number

QTY: Packing Quantity

CAT: Ranks

HUE: Peak Wavelength

REF: Reference

LOT No: Lot Number

MADE IN TAIWAN: Production Place

Notes

1. Above specification may be changed without notice. Everlight Americas will reserve authority on material

change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions for using

outlined in these specification sheets. Everlight Americas assumes no responsibility for any damage

resulting from use of the product which does not comply with the absolute maximum ratings and the

instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of Everlight Americas corporation.

Please don’t reproduce or cause anyone to reproduce them without Everlight Americas’s consent.