SPECIFICATION
SD-100B-5 SD-100C-5 SD-100D-5 SD-100C-12 SD-100D-12 SD-100C-24 SD-100D-24
(for D type only)
SD-100B-12 SD-100B-24
MODEL
DCVOLTAGE
RATEDCURRENT
CURRENTRANGE
RATEDPOWER
OUTPUT VOLTAGE ADJ.RANGE
LINEREGULATION
LOADREGULATION
SETUP,RISETIME
HOLDUP TIME(Typ.)
VOLTAGERANGE
EFFICIENCY (Typ.)
INPUT
EMSIMMUNITY
WORKINGTEMP.
WORKINGHUMIDITY
STORAGETEMP.,HUMIDITY
TEMP.COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVERVOLTAGE
DCCURRENT (Typ.)
5V 12V 24V
20A 8.5A 4.2A
0~20A 0~8.5A 0~4.2A
100W 102W 100.8W
100mVp-p 120mVp-p 150mVp-p
2.0% 1.0% 1.0%
4.5~5.5VDC 11~16VDC 23~30VDC
0.5%
0.5%
0.3%
0.3%
0.2%
0.2%
2s,50ms(onlyDmode)atfullload
20ms(onlyDmode)atfullload
B:19~36VDCC:36~72VDCD:72~144VDCor85~132VAC
74%
4.8A/24V 4.8A/24V 4.8A/24V
D:18A/96VDC
<0.75mA/120VAC(SD-100D)
75% 76% 75%
2.4A/48V 2.4A/48V2.4A/48V
77% 80% 78% 81% 83%
1.8A/96V 1.8A/96V 1.8A/96V
105~135% ratedoutputpower
5.75~6.75V/10%load 16.8~20V/10%load 31.5~37.5V/10%load
Protectiontype: Hiccupmode,recoversautomaticallyafterfaultconditionisremoved
Protectiontype:Hiccupmode,recoversautomaticallyafterfaultconditionisremoved
CompliancetoEN55022(CISPR22)ClassB
IEC60950-1CBapprovedby TUV(forDtypeonly)
Complianceto ightEN61000-4-2,3,4,6,8;ENV50204,l industrylevel,criteria A
-10~+60 (Refertooutputloadderatingcurve)
20~90%RHnon-condensing
-20~+85 ,10~95%RH
0.03%/ (0~50
10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes
356.7Khrsmin.(SD-100B)355.5Khrsmin.(SD-100C)341.9KHrsmin.(SD-100D)MIL-HDBK-217F(25 )
199*98*38mm(L*W*H)
0.65Kg;20pcs/13.8Kg/0.8CUFT
FileName:SD-100-SPEC2010-10-18
INRUSHCURRENT (Typ.)
LEAKAGECURRENT
SAFETY STANDARDS
100WSingleOutputDC-DCConverter
2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
Fixed switching frequency at 83KHz
24V and 48V input voltage design refer to LVD
Low cost
High reliability
2 years warranty
Features :
SD-100 series
EMICONDUCTION&RADIATION
ENVIRONMENT
SAFETY &
EMC
(Note4)
PROTECTION
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.
(as available on http://www.meanwell.com)
RIPPLE&NOISE(max.) Note.2
VOLTAGETOLERANCE Note.3
WITHSTANDVOLTAGE
ISOLATIONRESISTANCE
I/P-O/P:1.5KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC
I/P-O/P,I/P-FG,O/P-FG:100MOhms/500VDC /25 /70%RH
http://store.iiic.cc/
MechanicalSpecification
DeratingCurve StaticCharacteristics(SD-100D-24V)
FileName:SD-100-SPEC2010-10-18
CaseNo.902Unit:mm
AMBIENTTEMPERATURE( ) INPUTVOLTAGE(V)
55 60 65 70 75 80 90 100 110 120 130
35032
30028
25024
20020
15016
10012
508
OUTPUTVOLTAGE(V)
OUTPUTRIPPLE(mVp-p)
Ta=25
(HORIZONTAL)
(VERTICAL)
-10
-10
0
0
10 20 30 40 50
45
60
55
20
40
60
80
100
LOAD(%)
SD-100C,D-5,12
SD-100B-5,12,24
SD-100C,D-24
3.5
9
9
197
7
6.5 190
22 157
4.5
7
6
5
4
3
2
8.2
1
120
199
57.5
12
9.5
80
85.5
98
3.5
4-M3
3.5
18
9.5
18
3-M3
3.5
28.5
38
TerminalPinNo. Assignment
SD-100B,C
SD-100D
PinNo.
PinNo.
PinNo.
PinNo.
1,2
1
1,2
4,5
3
2
6,7
Assignment
Assignment
Assignment
Assignment
DCOUTPUT -V
DCOUTPUT +V
FG
INPUT
DCINPUT V+
AC/DCINPUT
DCINPUT V-
BlockDiagram fosc:83KHz
CIRCUIT
DETECTION
O.L.P.
O.V.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCHING FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
PWM
100WSingleOutputDC-DCConverter SD-100 series
http://store.iiic.cc/
