EE-SB5M - Omron Electronics

EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E

Photomicrosensor with 80-mA

Switching Capacity that can be Built into

Equipment

HBuilt-in amplifier with NPN output

HModels available with 5- to 12-VDC and 5-

to 15-VDC input

HCMOS- and TTL-compatible

H19-mm sensing distance (EE-SB5V-E)

HModel with easy adjustment with an

external sensitivity adjuster (EE-SB5V)

HConnectors available (EE-1001/1006)

HConvert to PNP output with EE-2002

conversion connector

Ordering Information

Appearance Sensing method Sensing distance Output configuration Weight Part number

Diffuse 5mm Light-ON Approx. 3.0 g EE-SB5M

Dark-ON

EE-SB5MC

Light-ON EE-SB5V

Dark-ON EE-SB5VC

19 mm Light-ON Approx. 2.8 g EE-SB5V-E

JACCESSORIES

Name Part number

Solder connector EE-1001

Connector with 2 m cable EE-1006

EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E

Specifications

JRATINGS

Item Diffuse

EE-SB5M EE-SB5MC EE-SB5V(-E) EE-SB5VC

Supply voltage 5to12VDC±10%, ripple (p-p): 10% max. 5to15VDC±10%, ripple (p-p): 10% max.

Current consumption 36 mA max. 48 mA max. (DC current: IF=25mA)

Maximum forward direct current (IF) — 30 mA max.

Forward voltage (VF) — 1.5 V max. (IF=30mA)

Reverse voltage (VR) — 4Vmax.

Standard reference object White paper with reflection factor of 90% (standard sensing object: 15 x 15 mm)

Differential distance 0.1 mm

Control output At 5 to 24 VDC: 80-mA load current (IC) with a residual voltage of 0.8 V max.

When driving TTL: 40-mA load current (IC) with a residual voltage of 0.4 V max.

Output

configuration

Transistor on output stage

without detecting object

OFF ON OFF ON

Transistor on output stage

with detecting object

ON OFF ON OFF

Response frequency (See note) 50 Hz

Connecting method EE-1001/1006 Connectors; soldering terminals/cordset

Light source GaAs infrared LED with a peak wavelength of 940 nm

Receiver Si photo-transistor with a sensing wavelength of 850 nm max.

Note: The response frequency was measured by detecting the following disks rotating.

Disk

15 mm

5mm

200 mm

dia.

JCHARACTERISTICS

Ambient temperature Operating -25°Cto55

°C(-13

°F to 131°F)

Storage -30°Cto80

°C(-22

°F to 176°F)

Ambient humidity Operating 45% to 85%

Storage 35% to 95%

Vibration resistance Destruction: 20 to 2,000 Hz (with a peak acceleration of 20G’s), 1.5-mm double amplitude for

4 min each in X, Y, and Z directions

Shock resistance Destruction: 500 m/s2for 3 times each in X, Y, and Z directions

Soldering heat resistance 260°±5°C (See Note.) when the portion between the tip of the terminals and the position

1.5 mm from the terminal base is dipped into the solder for 10±1 seconds

Note: This conforms to MIL-STD-750-2031-1.

EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-EEE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E

Engineering Data

JOPERATING RANGE (TYPICAL 1) JOPERATING RANGE (TYPICAL 2)

Distance Y (mm)

X (mm)

EE-SB5M(C) Reference object:

White paper ( 15 x 15 mm)

(reflection factor: 90%)

Operates

Releases Optical

axis

Distance Y (mm)

X’ (mm)

EE-SB5M(C) Reference ob-

ject: White paper

(15 x 15 mm)

(reflection factor:

90%)

Operates

Releases

Optical

axis X’

JSENSING DISTANCE VS. OBJECT

AREA (TYPICAL)

JSENSING DISTANCE VS. IFEE-SB5V-E

(TYPICAL)

Distance (mm)

EE-SB5M(C)

Reference object:

White paper ( 15 x 15 mm)

(reflection factor: 90%)

Area (mm2)

0510 15 202530

Forward Current IF(mA)

Sensing Distance d (mm)

TA= 25°C

Reference object

White paper:

(reflection factor 90%)

Operation

JINTERNAL/EXTERNAL CIRCUIT DIAGRAMS

Load

(relay)

Main

circuit

Logic

circuit

OUT

5to12VDC

←IC

Connect RLas

shown only

when logic cir-

cuit is driven.

LED

display

Load (relay)

Main

circuit

Logic circuit

OUT

5to15VDC

←IC

Current-limiting

resistor

EE-SB5M(C) Light-ON/Dark-ON EE-SB5V(C), EE-SB5V-E Light-ON/Dark-ON

JTIMING CHART

OFF

Output

transistor

Operates

Releases

Load (relay)

Output voltage

(logic)

OFF

Output

transistor

Operates

Releases

Load (relay)

Output voltage

(logic)

Interrupted

Incident Interrupted

Incident

Light-ON Dark-ON

EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E

Dimensions

Unit: mm (inch)

JEE-SB5M(C), EE-SB5V(C), EE-SB5V-E

Optical axis

Two, 3.2 dia.

holes

Optical

axis

Two, 3.8 dia.

holes

(1)(2)(3)(4)

Terminal Arrangement

(1)

(2)

(3)

(4)

VCC

OUT

OUTPUT

GND (0 V)

25.4 (1.00)

19.0 (0.75)

9.8

(0.39)

6.95

(0.27)

6.35

(0.25) 4.55

(0.18)

9.0

(0.35)

13.2

(0.52)

5.5

(0.22)

8.0

(0.31)

6.2

(0.24)

2.55

(0.10)

0.6

(0.02)

1.2 (0.05) 1.5

13.0 (0.51)

0.8

(0.03)

1.45 (0.06)

2.54 (0.10)

0.3

(0.01)

16.7

(0.66)

10.8

(0.48)

6.0

(0.24)

22.2

(0.87)

(1.02)

16.2

(0.64)

JEE-SB5M(C)/SB5V(C)/SB5V-E + EE-1001 JEE-SB5M(C)/SB5V(C)/SB5V + EE-1006

JEE-1001 SOLDER CONNECTOR

2.54±0.15

2.9±1

4.0

(0.16)

10.8

(0.43)

6.0

(0.24)

0.6

(0.02)

13.0 (0.51)

JEE-1006 CONNECTOR WITH CABLE

(1)

(2)

(3)

(4)

Terminal Arrangement

IEC colors are shown in parentheses.

(1) Red (Brown) VCC

(2) Yellow (Pink) L L

(3) White (Black) OUT OUTPUT

(4) Black (Blue) GND (0 V)

0.6

(0.02)

11.8

(0.46)

2.54

(0.10) 5.3

(0.21)

16.2 (0.64) 20 (0.79) 2,000

(78.74) 25

(0.98)

(0.59)

EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-EEE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E

Note: Supply 5 to 12 V to the EE-SB5M(C). Wire as shown by the following diagram if the supply voltage exceeds 12 V.

VCC (1)

VCC (2) R

GND

ZVCC (2) = VCC (1) x Z

Z+R

Note: Z is the internal impedance between the positive and negative terminals.

Model VCC (2) Z(

Ω)

EE-SB5M(C) 5to12V 360

Precautions

Refer to the Technical Information Section for general

precautions.

An external sensitivity adjuster can be connected to the

EE-SB5V(C), EE-SB5V-E Photomicrosensor. When connecting

the sensitivity adjuster, insert resistor RF(current-limiting

resistor), as shown by the diagram. The value of RFis obtainable

as follows:

RF>(VCC - 1.5 V)/30 mA

Vcc

Output

External sensitivity adjuster

IFRF

OUT

Note: The EE-SB5V(C) and EE-SB5V-E have no constant current circuit to protect the LED. For this reason, the LED will be damaged by

excessive current applied to the positive terminal. To prevent potential LED damage, connect a current-limiting resistor, as shown

previously.

Cat. No. GC APMS-1 09/02 Specifications subject to change without notice. Printed in U.S.A.

OMRON ELECTRONICS LLC

OneEastCommerceDrive

Schaumburg, IL 60173

NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.

1-800-55-OMRON

OMRON CANADA, INC.

885 Milner Avenue

416-286-6465

OMRON ON--LINE

Global -- http://www.omron.com

USA -- http://www.omron.com/oei

Canada -- http://www.omron.com/oci

Toronto, Ontario M1B 5V8