Si9112 Vishay Siliconix High-Voltage Switchmode Controller FEATURES D 9- to 80-V Input Range D Current-Mode Control D High-Speed, Source-Sink Output Drive D High Efficiency Operation (> 80%) D Internal Start-Up Circuit D Internal Oscillator (1 MHz) D SHUTDOWN and RESET DESCRIPTION The Si9112 is a BiC/DMOS integrated circuit designed for use in high-efficiency switchmode power converters. A high-voltage DMOS input allows this controller to work over a wide range of input voltages (9- to 80-VDC). Current-mode PWM control circuitry is implemented in CMOS to reduce internal power consumption to less than 10 mW. power. When combined with an output MOSFET and transformer, the Si9112 can be used to implement single-ended power converter topologies (i.e., flyback, forward, and cuk). The Si9112 is available in both standard and lead (Pb)-free 14-pin plastic DIP and SOIC packages which are specified to operate over the industrial temperature range of -40 _C to 85 _C. A CMOS output driver provides high-speed switching of MOSPOWER devices large enough to supply 50 W of output FUNCTIONAL BLOCK DIAGRAM FB COMP 14 DISCHARGE 13 9 OSC IN 8 Error Amplifier VREF OSC OUT 7 OSC To VCC - 10 Clock + (1/2 fOSC) 4 V (2%) 2V Ref Gen - Current-Mode Comparator + 4 R Q 5 S OUTPUT -VIN + - BIAS VCC +VIN 1 Current Sources 6 To Internal Circuits 2 1.2 V 3 VCC - 8.1 V C/L Comparator + Undervoltage Comparator S Q R 11 12 SENSE SHUTDOWN RESET - + 8.7 V Pre-Regulator/Start-Up Applications information, see AN703. sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 www.vishay.com 1 Si9112 Vishay Siliconix ABSOLUTE MAXIMUM RATINGS Voltages Referenced to -VIN (VCC < +VIN + 0.3 V) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_C VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Power Dissipation (Package)a 14-Pin Plastic DIP (J Suffix)b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750 mW 14-Pin SOIC (Y Suffix)c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 mW +VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 V Logic Inputs (RESET, SHUTDOWN, OSC IN) . . . . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Linear Inputs (FEEDBACK, SENSE) . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V HV Pre-Regulator Input Current (continuous) . . . . . . . . . . . . . . . . . . . . 25 mA (Power Dissipation Limited) Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to 150_C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 to 85_C Thermal Impedance (JA) 14-Pin Plastic DIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167_C/W 14-Pin SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140_C/W Notes a. Device mounted with all leads soldered or welded to PC board. b. Derate 6 mW/_C above 25_C. c. Derate 7.2 mW/_C above 25_C. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE Voltages Referenced to -VIN VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 V to 13.5 V ROSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 k to 1 M +VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 V to 80 V Linear Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to VCC - 3 V fOSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 kHz to 1 MHz Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to VCC SPECIFICATIONSa Test Conditions Unless Otherwise Specified Parameter Symbol Limits D Suffix -40 to 85_C DISCHARGE = -VIN = 0 V VCC = 9 V, +VIN = 12 V RBIAS = 270 k , ROSC = 330 k Tempb Mind Typc Maxe Unit OSC IN = - VIN (OSC Disabled) RL = 10 M Room Fulle 3.88 3.82 4.0 4.12 4.14 V Room 15 30 45 k Room 70 100 130 A 0.5 1.0 mV/_C Reference Output Voltage VR Output Impedancee ZOUT Short Circuit Current ISREF Temperature Stabilitye VREF = -VIN TREF Full Oscillator Maximum Frequencye Initial Accuracy Voltage Stability Temperature Coefficiente fMAX fOSC f/f ROSC = 0 Room 1 3 ROSC = 330 k, See Note f Room 80 100 120 ROSC = 150 k, See Note f Room 160 200 240 f/f = f(13.5 V) - f(9.5 V) / f(9.5 V) Room 9 15 % Full 200 500 ppm/_C 4.00 4.08 V TOSC MHz kHz Error Amplifier Feedback Input Voltage VFB FB Tied to COMP OSC IN = - VIN (OSC Disabled) Room Input Offset Voltage VOS OSC IN = - VIN (OSC Disabled) Room "15 "40 mV Input BIAS Current IFB OSC IN = - VIN, VFB = 4 V Room 25 500 nA AVOL OSC IN = - VIN Room 60 BW OSC IN = - VIN (OSC Disabled) Room 1 ZOUT Error Amp Configured for 60 dB gain Room 1000 2000 Source VFB = 3.4 V Room -2.0 -1.4 Sink VFB = 4.5 V Room 0.12 0.15 9 V v VCC v 13.5 V Room 50 70 Open Loop Voltage Gaine Unity Gain Bandwidthe Dynamic Output Impedancee Output Current Power Supply Rejectione www.vishay.com 2 IOUT PSRR 3.92 80 dB 1.5 MHz mA dB sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 Si9112 Vishay Siliconix SPECIFICATIONSa Test Conditions Unless Otherwise Specified Parameter Limits D Suffix -40 to 85_C DISCHARGE = -VIN = 0 V VCC = 9 V, +VIN = 12 V RBIAS = 270 k , ROSC = 330 k Tempb Mind VSOURCE VFB = 0 V Room 1.1 td VSENSE = 1.5 V, See Figure 1 Room Symbol Typc Maxe Unit Current Limit Threshold Voltage Delay to Outpute 1.3 1.5 V 100 150 ns 10 A Pre-Regulator/Start-Up Input Voltage +VIN IIN = 10 A Room Input Leakage Current +IIN VCC w 9.4 V Room ISTART +VIN = 48 V Room 12 Pre-Regulator Start-Up Current 80 V 20 mA VCC +VIN = 10 V, RLOAD = 4 k at Pin 6 Room VUVLO +0.1 VCC Pre-Regulator Turn-Off Threshold Voltage VREG IPRE-REGULATOR = 10 A Room 8.0 8.7 9.4 Undervoltage Lockout VUVLO See Detailed Description Room 7.2 8.1 8.9 VREG -VUVLO VDELTA Room 0.3 0.6 Pre-Regulator Dropout Voltage V Supply Supply Current ICC Bias Current CL v 75 pF (Pin 4) IBIAS Room 0.6 Room 15 Room 50 1.0 mA A Logic SHUTDOWN Delaye SHUTDOWN Pulse Widthe tSD CL = 500 pF VSENSE = -VIN, See Figure 2 100 tSW Room 50 RESET Pulse Widthe tRW Room 50 Latching Pulse Width SHUTDOWN and RESET Lowe tLW Room 25 Input Low Voltage VIL Room Input High Voltage VIH Room Input Current Input Voltage High IIH VLOGIC = VCC Room Input Current Input Voltage Low IIL VIN = 0 V Room -35 Output High Voltage VOH IOUT = -10 mA Room Full 8.7 8.5 Output Low Voltage VOL IOUT = 10 mA Room Full Output Resistancee ROUT IOUT = 10 mA, Source or Sink Room Full 20 25 30 50 Room 40 75 Room 40 75 See Figure 3 ns 2.0 V 5 A 7.0 1 25 Output Rise Timee Fall Timee tr tf CL = 500 pF 0.3 0.5 V ns Notes a. Refer to PROCESS OPTION FLOWCHART for additional information. b. Room = 25_C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum. e. Guaranteed by design, not subject to production test. f. CSTRAY Pin 8 = v 5 pF. sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 www.vishay.com 3 Si9112 Vishay Siliconix TIMING WAVEFORMS SENSE 1.5 V - 50% 0 VCC SHUTDOWN 0 tr v 10 ns 50% tf v 10 ns - tSD td VCC VCC 90% OUTPUT 0 - 90% OUTPUT 0 - FIGURE 1. FIGURE 2. tSW VCC SHUTDOWN 0 50% 50% - tf, tf v 10 ns tLW VCC RESET 0 50% 50% 50% - tRW FIGURE 3. TYPICAL CHARACTERISTICS Output Switching Frequency vs. Oscillator Resistance +VIN vs. +IIN at Start-Up 140 1M VCC = -VIN 120 f OUT (Hz) +V IN (V) 100 80 60 100 k 40 20 0 10 k 10 15 +IIN (mA) FIGURE 4. www.vishay.com 4 20 10 k 100 k 1M rOSC - Oscillator Resistance () FIGURE 5. sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 Si9112 Vishay Siliconix PIN CONFIGURATIONS AND ORDERING INFORMATION Dual-In-Line and SOIC BIAS 1 14 FB +VIN 2 13 COMP SENSE 3 12 RESET OUTPUT 4 11 SHUTDOWN -VIN 5 10 VREF VCC 6 9 DISCHARGE OSC OUT 7 8 OSC IN ORDERING INFORMATION Part Number Temperature Range Package Si9112DY Si9112DY-T1 Si9112DY-T1--E3 Si9112DJ Si9112DJ--E3 SOIC-14 -40 to 85_C PDIP-14 Top View DETAILED DESCRIPTION Pre-Regulator/Start-Up Section Due to the low quiescent current requirement of the Si9112 control circuitry, bias power can be supplied from the unregulated input power source, from an external regulated low-voltage supply, or from an auxiliary "bootstrap" winding on the output inductor or transformer. When power is first applied during start-up, +VIN (pin 2) will draw a constant current. The magnitude of this current is determined by a high-voltage depletion MOSFET device which is connected between +VIN and VCC (pin 6). This start-up circuitry provides initial power to the IC by charging an external bypass capacitance connected to the VCC pin. The charging current is disabled when VCC exceeds 8.7 V. If VCC is not forced to exceed the 8.7-V threshold, then VCC will be regulated to a nominal value of 8.7 V by the pre-regulator circuit. As the supply voltage rises toward the normal operating conditions, an internal undervoltage (UV) lockout circuit keeps the output driver disabled until VCC exceeds the UV lockout threshold (typically 8.1 V). This guarantees that the control logic will be functioning properly and that sufficient gate drive voltage is available before the MOSFET turns on. The design of the IC is such that the undervoltage lockout threshold will be at least 300 mV less than the pre-regulator turn-off voltage. Power dissipation can be minimized by providing an external power source to VCC such that the pre-regulator circuit is disabled. BIAS To properly set the bias for the Si9112, a 270-k resistor should be tied from BIAS (pin 1) to -VIN (pin 5). This sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 determines the magnitude of bias current in all of the analog sections and the pull-up current for the SHUTDOWN and RESET pins. The current flowing in the bias resistor is nominally 15 A. Reference Section The reference section of the Si9112 consists of a temperature compensated buried zener and trimmable divider network. The output of the reference section is connected internally to the non-inverting input of the error amplifier. Nominal reference output voltage is 4 V. The trimming procedure that is used on the Si9112 brings the output of the error amplifier (which is configured for unity gain during trimming) to within "2% of 4 V. This automatically compensates for input offset voltage in the error amplifier. The output impedance of the reference section has been purposely made high so that a low impedance external voltage source can be used to override the internal voltage source, if desired, without otherwise altering the performance of the device. Error Amplifier Closed-loop regulation is provided by the error amplifier. The emitter follower output has a typical dynamic output impedance of 1000 , and is intended for use with "around-the-amplifier" compensation. A MOS differential input stage provides low input leakage current. The noninverting input to the error amplifier (VREF) is internally connected to the output of the reference supply and should be bypassed with a small capacitor to ground. www.vishay.com 5 Si9112 Vishay Siliconix DETAILED DESCRIPTION (CONT'D) Oscillator Section The oscillator consists of a ring of CMOS inverters, capacitors, and a capacitor discharge switch. Frequency is set by an external resistor between the OSC IN and OSC OUT pins. (See Typical Characteristics for details of resistor value vs. frequency.) The DISCHARGE pin should be tied to -VIN for normal internal oscillator operation. A frequency divider in the logic section limits switch duty cycle to v50% by locking the switching frequency to one half of the oscillator frequency. Remote synchronization can be accomplished by capacitive coupling of a SYNC pulse into the OSC IN (pin 8) terminal. For a 5-V pulse amplitude and 0.5-s pulse width, typical values would be 100 pF in series with 3 k to pin 8. SHUTDOWN and RESET SHUTDOWN (pin 11) and RESET (pin 12) are intended for overriding the output MOSFET switch via external control logic. The two inputs are fed through a latch preceding the output switch. Depending on the logic state of RESET, SHUTDOWN can be either a latched or unlatched input. The output is off whenever SHUTDOWN is low. By simultaneously having SHUTDOWN and RESET low, the latch is set and SHUTDOWN has no effect until RESET goes high. The truth table for these inputs is given in Table 1. Table 1: Truth Table for the SHUTDOWN and RESET Pins SHUTDOWN RESET H H H Output Normal Operation Normal Operation (No Change) L H L L Off (Not Latched) Off (Latched) L Off (Latched, No Change) Both pins have internal current source pull-ups and should be left disconnected when not in use. An added feature of the current sources is the ability to connect a capacitor and an open-collector driver to the SHUTDOWN or RESET pins to provide variable shutdown time. Output Driver The push-pull driver output has a typical on-resistance of 20 . Maximum switching times are specified at 75 ns for a 500 pF load. This is sufficient to directly drive 60-V, 25-A MOSFETs. Larger devices can be driven, but switching times will be longer, resulting in higher switching losses. For applications information refer to AN703. Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?70005. www.vishay.com 6 sDocument Number: 70005 S-42036--Rev. H, 15-Nov-04 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1 Package Information Vishay Siliconix SOIC (NARROW): 14-LEAD (POWER IC ONLY) MILLIMETERS 14 13 12 11 10 9 Dim A A1 B C D E e H L O 8 E 2 3 4 5 6 7 D A e B Document Number: 72809 28-Jan-04 A1 0.25 (GAGE PLANE) 1 H INCHES Min Max Min Max 1.35 1.75 0.053 0.069 0.10 0.20 0.004 0.008 0.38 0.51 0.015 0.020 0.18 0.23 0.007 0.009 8.55 8.75 0.336 0.344 3.8 4.00 0.149 0.157 1.27 BSC 0.050 BSC 5.80 6.20 0.228 0.244 0.50 0.93 0.020 0.037 0_ 8_ 0_ 8_ ECN: S-40080--Rev. A, 02-Feb-04 DWG: 5914 C ALL LEADS L O 0.101 mm 0.004 www.vishay.com 1 Package Information Vishay Siliconix PDIP: 14-LEAD (POWER IC ONLY) 14 13 12 11 10 9 8 E E1 1 2 3 4 5 6 7 D S Q1 A A1 B1 e1 L B Dim A A1 B B1 C D E E1 e1 eA L Q1 S 15 MAX C eA MILLIMETERS Min Max INCHES Min Max 3.81 5.08 0.150 0.200 0.38 1.27 0.015 0.050 0.38 0.51 0.015 0.020 0.89 1.65 0.035 0.065 0.20 0.30 0.008 0.012 17.27 19.30 0.680 0.760 7.62 8.26 0.300 0.325 5.59 7.11 0.220 0.280 2.29 2.79 0.090 0.110 7.37 7.87 0.290 0.310 2.79 3.81 0.110 0.150 1.27 2.03 0.050 0.080 1.02 2.03 0.040 0.080 ECN: S-40081--Rev. A, 02-Feb-04 DWG: 5919 Document Number: 72814 28-Jan-04 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000