ZHX1423 SIR UltraSlimTM Transceivers Product Specification PS024903-1005 ZiLOG Worldwide Headquarters * 532 Race Street * San Jose, CA 95126-3432 Telephone: 408.558.8500 * Fax: 408.558.8300 * www.ZiLOG.com This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters 532 Race Street San Jose, CA 95126-3432 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated. Document Disclaimer (c)2005 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers iii Table of Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 VCC Positive Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GND Ground 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 RXD Receive Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TXD Transmit Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LEDA LED Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical and Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ZHX1423 Tape and Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ZHX1423 Soldering and Cleaning Recommendations . . . . . . . . . . . . . . . . . . . . Reflow Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 8 8 Moisture Prevention Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Baking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Mechanical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Customer Feedback Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problem Description or Suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS024903-1005 11 11 11 11 11 ZHX1423 SIR UltraSlim Transceivers iv List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. ZHX1423 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ZHX1423 Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 4 ZHX1423 Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ZHX1423 Tape Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ZHX1423 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ZHX1423 Mechanical Specification . . . . . . . . . . . . . . . . . . . . . . . . . 10 List of Tables Table 1. Table 2. Table 3. Table 4. PS024903-1005 ZHX1423 Transceiver Pin Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 5 5 ZHX1423 SIR UltraSlim Transceivers 1 Description The ZILOG ZHX1423 for PDAs, internet appliances, medical electronics, and general-purpose interactive handheld devices is the smallest, lowest power, and highest functional standard-power (0-1 meter minimum range) transceiver available. The ZiLOG ZHX1423 features exclusive AlwaysOnTM technology that allows the transceiver to "listen" for an IrDA communication at a typical current of 6 A, allowing the default mode to be left on with negligible effect on the battery life. The UltraSlim form factor (7.3 mm long x 2.8 mm wide x 1.9 mm high) allows placement in virtually any small device. Application circuit space is also minimized because only two external components are required. The ZHX1423 is designed to support IrDA-Data SIR mode (115.2 Kbits/s) and provides typical data links with other standard-power IrDA transceivers up to 1.0 meter away. The transceiver combines an IRED emitter, a PIN photodiode, and a unique driver/control ASIC in a single package, as shown in Figure 1. Figure 1. ZHX1423 Block Diagram The ZILOG ZHX1423 also features a shutdown control that minimizes current draw to 0.1 A typical. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 2 Features * * * * * * Compliant to IrDA Data Specification 1.4 Standard Power SIR * Meets IEC 825-1 Class 1 eye safety specifications Low-power supply voltage range: 2.4 to 3.6 V ZHX1423 listening current: only 6 A (typically) at 3.0 V (ZiLOG exclusive) UltraSlim package: 7.3 mm long x 2.8 mm high x 1.9 mm wide Extended operating temperature range: -30 C to +85 C Internal current source eliminates need for a current-limiting resistor for IR LED Pin Description Table 1 lists the pin out for the ZHX1423 transceivers. The pins are described in this section. Table 1. ZHX1423 Transceiver Pin Out Pin Name Function I/O 1 NC NC (future use) -- 2 VCC Supply voltage -- 3 GND Ground -- 4 SD Shutdown I 5 RXD Receiver output O 6 TXD Transmitter input I 7 LEDA IRED anode -- VCC Positive Supply (Power) Connect to positive power supply (2.4-3.6 V). Filter with a 1.0-F ceramic bypass capacitor and terminating resistor as close as possible to the VCC pin. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 3 GND Ground (Power) Connect to ground of the power supply. A solid ground plane is recommended for proper operation. SD Shutdown (Input, active high) This input is used to place the transceiver into a shutdown mode. RXD Receive Data (Output, active low) This output provides received serial data. It is a tri-state, slew rate controlled CMOS output (tri-stated during shutdown) driver capable of driving a standard CMOS or LS series TTL load. No external resistor is required. TXD Transmit Data (Input, active high) This CMOS input is used to transmit serial data and has an internal pull-down resistor that is enabled during shutdown. LEDA LED Driver (Output, active low) This output is internally connected to the LED anode and contains an internal current source. The voltage range on this pad is 2.2-4.2 volts. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 4 Application Block Diagrams Figure 2 shows the application block diagrams for the ZHX1423 transceivers. ZHX1423 =2.4 to 4.2 V ZHX1423 Figure 2. ZHX1423 Application Block Diagrams PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 5 Electrical and Timing Specifications Table 2, Table 3, and Table 4 list the electrical and timing specifications. Table 2. Absolute Maximum Ratings Parameter Symbol Min Max Unit Comment Supply voltage VCC -0.3 3.6 V VCC, GND Supply voltage VLED -0.3 4.4 V Input voltage VIN GND-0.3 VCC+0.3 V TXD, SD Output (Ext.) voltage VOUT GND-0.3 VCC+0.3 V RXD Storage temperature TST -40 100 C Solder temperature TSOL 230 C 400 V ESD Table 3. Recommended Operating Conditions Parameter Symbol Min Max Unit Supply voltage VCC 2.4 3.6 V Supply voltage, LEDA VLED 2.4 4.2 V Ambient operating temperature TOP -30 85 C Table 4. Electrical Characteristics Parameter Symbol Condition High-level input voltage VIH Low-level input voltage VIL High-level output voltage VOH IOH=-100 A Low-level output voltage VOL IOL=100 A Transmitter current ILED 260 Listening current ICC 6 PS024903-1005 Min Typical Max Unit 0.75VCC Remarks V TXD, SD V TXD, SD V RXD 0.4 V RXD 320 mA 0.4 VCC-0.4 A ZHX1423 SIR UltraSlim Transceivers 6 Table 4. Electrical Characteristics (Continued) Parameter Symbol Condition Receive current ICC 100 125 A Idle Standby current ISTB 0.1 1.0 A SD=VCC, TXD=0 V RXD pulse width tPWA 5 s Input pulse=1.6 s; rise/fall time<600 ns Power shutdown time TSD 1 s Startup time TSTU 200 s Latency TRRT 150 s SIR<115.2 Kbps Min Typical 1.0 Transmitter LED timeout 130 Max Unit 270 s Rise/fall time Tr, Tf Cload=25 pF 10 40 ns Trans. radiant intensity IE ILED=260 mA 40 100 mW/sr Minimum threshold irradiance Eemin VCC=3.3 V Maximum input irradiance Eemax VCC=3.3 V Peak wavelength 4 Remarks Protects LED when TXD is left high On-axis W/cm2 h, v<(+15) mW/cm2 h, v<(+15) 500 870 nm Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=25 C Note: To minimize power dissipation, the part has been designed for optimal operation in 1.6 s mode. If used in the 3/16th pulse duration mode, some devices will exhibit a phantom RxD pulse at 9.6 Kbits/s. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 7 ZHX1423 Tape and Reel Specifications Figure 3 shows the ZHX1423 reel specifications, and Figure 4 shows the ZHX1423 tape specifications. 8 0.1 (4 ) (7 .1 ) LE DA(7pin) (6 .7 5 ) N/C(1pin) Polari ty 0.4 0.05 2.85 0.1 (2.0) (3.075) 1.0 0.1 (1.0) Figure 4. ZHX1423 Tape Specifications PS024903-1005 2 0.1 7 .5 0 .1 4 0.1 0.9 1 6 0 .2 +0.1 1.5- 0 1 .7 5 0 .1 Figure 3. ZHX1423 Reel Specifications ZHX1423 SIR UltraSlim Transceivers 8 ZHX1423 Soldering and Cleaning Recommendations Follow these recommendations to maintain the performance of the ZHX1423 transceivers. Reflow Soldering Note: Please refer to ZiLOG's Lead-Free Solder Reflow: Packaging Application Note (AN0161, http://www.zilog.com/docstools.asp) for more information about the solder profile. Manual Soldering * * * * Use 63/37 or silver solder. Temperature at solder iron tip: no more than 280 C Finish soldering within 3 seconds. Handle only after the ZHX1423 transceivers have cooled off. Cleaning Perform cleaning under the following conditions: * * * PS024903-1005 Cleaning agent: alcohol Temperature and time 30 seconds below 50 C or 3 minutes below 30 C Ultrasonic cleaning: below 20 W ZHX1423 SIR UltraSlim Transceivers 9 Moisture Prevention Guidelines To avoid moisture absorption during transportation and storage, ZHX1423 reels are packed in aluminum envelopes (see Figure 5) that contain a desiccant with a humidity indicator. While this packaging is an impediment to moisture absorption, it is by no means absolute, and no warranty is implied. The user must store these parts in a controlled environment to prevent moisture entry. Please read the label on the aluminum bag for indicator instructions. Figure 5. ZHX1423 Packaging Baking Parts that have been stored over 12 months or unpacked over 72 hours should be baked under the following guidelines. Reels 60 C for 48 hours or more Loose Parts * 100 C for 4 hours or more or * 125 C for 2 hours or more or * PS024903-1005 150 C for 1 hour or more ZHX1423 SIR UltraSlim Transceivers 10 Mechanical Specification Figure 6 shows the mechanical specification for the ZHX1423 transceivers. Figure 6. ZHX1423 Mechanical Specification Ordering Information Use the following information to order the ZHX1423 transceivers: ZHX1423TA115THTR with AlwaysOn Listen 2,500 per reel Note: All ZiLOG devices are available lead free. ZHX1423 has always been lead free. These devices meet or exceed RoHS Directive 2002/95/EC. For additional information, please see the ZiLOG Quality and Reliability web page at http://www.zilog.com/quality/index.asp. PS024903-1005 ZHX1423 SIR UltraSlim Transceivers 11 Customer Feedback Form If you experience any problems while operating this product, or if you note any inaccuracies while reading this product specification, please copy and complete this form, then mail or fax it to ZiLOG (see Return Information, below). We also welcome your suggestions! Customer Information Name Country Company Phone Address Fax City/State/Zip email Product Information Serial # or Board Fab #/Rev # Software Version Document Number Host Computer Description/Type Return Information ZiLOG System Test/Customer Support 532 Race Street San Jose, CA 95126-3432 Fax: (408) 558-8300 Web: www.zilog.com Problem Description or Suggestion Provide a complete description of the problem or your suggestion. If you are reporting a specific problem, include all steps leading up to the occurrence of the problem. Attach additional pages as necessary. PS024903-1005