Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 1Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IR Receiver Modules for Remote Control Systems
MECHANICAL DATA
Pinning
1 = GND, 2 = GND, 3 = VS, 4 = OUT
DESCRIPTION
The TSOP361.. series are miniaturized SMD-IR receiver
modules for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be decoded by
a microprocessor. The main benefit is the operation with
short burst transmission codes and high data rates at a
supply voltage of 3 V.
This component has not been qualified according to
automotive specifications.
FEATURES
• Photo detector and preamplifier in one
package
• Internal filter for PCM frequency
• Continuous data transmission possible
• TTL and CMOS compatibility
• Output active low
• Supply voltage: 2.7 V to 5.5 V
• Compliant to RoHS Directive 2011/65/EU and in
accordance to WEEE 2002/96/EC
SPECIAL FEATURES
• Enhanced data rate up to 4000 bit/s
• Operation with short burst possible ( 6 cycles/burst)
• Taping available for topview and sideview assembly
BLOCK DIAGRAM APPLICATION CIRCUIT
16797
1234
PARTS TABLE
CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES (AGC1)
36 kHz TSOP36136
38 kHz TSOP36138
40 kHz TSOP36140
56 kHz TSOP36156
30 kΩ
VS
OUT
Demo -
GND
pass
AGCInput
PIN
Band
dulator
Control circuit
3
4
1; 2
16839
C1=
4.7 µF
TSOPxxxx
GND
Circuit
µC
R1= 100 Ω
+ VS
GND
Transmitter
with
TSALxxxx
VS
R1 and C1 recommended to suppress power supply
disturbances. The output voltage should not be
hold continuously at a voltage below VO = 2.0 V
by the external circuit.
VO
17170
OUT
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 2Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Fig. 1 - Output Function Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage (pin 3) VS- 0.3 to + 6 V
Supply current (pin 3) IS3mA
Output voltage (pin 4) VO- 0.3 to (VS + 0.3) V
Output current (pin 4) IO10 mA
Junction temperature Tj100 °C
Storage temperature range Tstg - 40 to + 100 °C
Operating temperature range Tamb - 25 to + 85 °C
Power consumption Tamb 85 °C Ptot 30 mW
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply current Ev = 0 ISD 0.7 1.2 1.5 mA
Ev = 40 klx, sunlight ISH 1.3 mA
Supply voltage VS2.7 5.5 V
Transmission distance Ev = 0, test signal see fig. 1, IR diode TSAL6200,
IF = 400 mA d35m
Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1 VOSL 250 mV
Minimum irradiance
(30 kHz to 40 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.35 0.5 W/m2
Minimum irradiance
(56 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.4 0.6 W/m2
Minimum irradiance
(30 kHz to 40 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.45 0.6 W/m2
Minimum irradiance
(56 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.5 0.7 W/m2
Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee max. 30 W/m2
Directivity Angle of half transmission distance 1/2 ± 45 deg
Ee
T
tpi *) t
VO
VOH
VOL tpo 2) t
14337
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
Output Signal
td 1)
1) 3/f0 < td < 9/f0
2) tpi - 4/f0 < tpo < tpi + 6/f0
*) tpi ≥ 6/f0 is recommended for optimal function
t - Output Pulse Width (ms)
0.00
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.1 110 100 1000 10 000
E
e
- Irradiance (mW/m²)
16907
po
Input Burst Duration
= 950 nm,
optical test signal, fig.1
Output Pulse
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 3Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 3 - Output Function
Fig. 4 - Output Pulse Diagram
Fig. 5 - Frequency Dependence of Responsivity
Fig. 6 - Sensitivity in Bright Ambient
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Ee
t
VO
VOH
VOL t
600 µs 600 µs
t = 60 ms
ton toff
94 8134
Optical Test Signal
Output Signal, (see fig. 4)
T ,T - Output Pulse Width (ms)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.1 1 10 100 1000 10 000
Ee - Irradiance (mW/m2)16910
Toff
= 950 nm,
optical test signal, fig. 3
Ton
on off
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0.7 0.9 1.1 1.3
f/f
0
- Relative Frequency
16926
f (3 dB) = f
0
/7
E
e min.
/E
e
- Rel. Responsivity
f = f
0
± 5 %
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.01 0.1 1 10 100
E - Ambient DC Irradiance (W/m
2
)
16911
Correlation with ambient light sources:
10 W/m21.4 klx (Std.illum.A, T= 2855 K)
10 W/m28.2 klx (Daylight, T= 5900 K)
Ambient, = 950 nm
E
e min.
- Threshold Irradiance (mW/m
2
)
0.0
0.5
1.0
1.5
2.0
0.1 1 10 100 1000
V
sRMS
- AC Voltage on DC Supply Voltage (mV)
16912
f = fo
f = 10 kHz
E
e min.
- Threshold Irradiance (mW/m²)
f = 1 kHz
f = 100 Hz
E
e min.
- Threshold Irradiance (mW/m²)
0.0 0.4 0.8 1.2 1.6
0.0
0.4
0.8
1.2
2.0
E - Field Strength of Disturbance (kV/m)
2.0
94 8147
1.6
f(E) = f
0
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 4Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length
Fig. 10 - Sensitivity vs. Ambient Temperature
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Fig. 12 - Directivity
Fig. 13 - Sensitivity vs. Supply Voltage
0.0
0.1
0.2
0.3
0.4
0.5
0.6
- 30 - 15 0 15 30 45 60 75 90
Tamb - Ambient Temperature (°C)16918
Sensitivity in dark ambient
E - Threshold Irradiance (mW/m²)
e min.
0.0
0.2
0.4
0.6
0.8
1.0
1.2
750 850 950 1050 1150
λ- Wavelength (nm)16919
S ( ) - Relative Spectral Sensitivityλrel
16801
0.4 0.2 0 0.2 0.4 0.6
0.6
0.9
0°
30°
10° 20°
40°
50°
60°
70°
80°
1.0
0.8
0.7
d
rel
- Relative Transmission Distance
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VS - Supply Voltage (V)17185
E - Sensitivity (mW/m )
2
e min.
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 5Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUITABLE DATA FORMAT
The circuit of the TSOP361.. is designed so that unexpected
output pulses due to noise or disturbance signals are
avoided. A bandpass filter, an integrator stage and an
automatic gain control are used to suppress such
disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length and
duty cycle.
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center frequency of
the bandpass (e.g. 38 kHz)
• Burst length should be 6 cycles/burst or longer
• After each burst which is between 6 cycles and 70 cycles
a gap time of at least 10 cycles is necessary
• For each burst which is longer than 1.8 ms a
corresponding gap time is necessary at some time in the
data stream. This gap time should be as long as the burst
or longer
• Up to 2200 short bursts per second can be received
continuously
Some examples for suitable data format are: NEC code,
Toshiba Micom Format, Sharp code, RC5 code, RC6 code,
RCMM code, R-2000 code, RECS-80 code.
When a disturbance signal is applied to the TSOP361.. it can
still receive the data signal. However the sensitivity is
reduced to that level that no unexpected pulses will occur.
Some examples for such disturbance signals which are
suppressed by the TSOP361.. are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signal at 38 kHz or at any other frequency
• Signals from fluorescent lamps with electronic ballast
(see figure 14)
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation
0101520
Time (ms)
16920
IR Signal
5
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 6Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PACKAGE DIMENSIONS in millimeters
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handling after reflow should be done only after the work
surface has been cooled off
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
2.35
R 1.7
5.51
0.5 ± 0.15
3 x 1.27 = 3.81
2.6
7.5
7.2
4x
1.27
5.3
2.9
4
2.2
Pick and place area. TR taping
2.2
3 x 1.27 = 3.81
1.27 0.9
2.8
specifications
according to DIN
technical drawings
Not indicated tolerances ± 0.3
Pick and place area. TT taping
Footprint
(1.5)
(1.4)
Issue: 8; 02.09.09
16776
Drawing-No.: 6.544-5341.01-4
A
A
0.1
0.1
0.3
0.4
14
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 7Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
TAPING VERSION TSOP..TT DIMENSIONS in millimeters
0
50
100
150
200
250
300
0 50 100 150 200 250 300
t (s)
T (°C)
255 °C
240 °C
245 °
C
max. 260 °C
max. 120 s max. 100 s
217 °C
max. 20 s
max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s
max. 2 cycles allowed
19800
16584
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 8Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TAPING VERSION TSOP..TR DIMENSIONS in millimeters
16585
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 9Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
REEL DIMENSIONS in millimeters
LEADER AND TRAILER DIMENSIONS in millimeters
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
(300 ± 10) mm/min.
165° to 180° peel angle
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
16734
Trailer Leader
no devices
min. 200 min. 400
StartEnd
devices
96 11818
no devices
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 10 Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
• Storage temperature 10 °C to 30 °C
• Storage humidity 60 % RH max.
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags.
EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING ABBREVIATION LENGTH
Item-description - 18
Item-number INO 8
Selection-code SEL 3
LOT-/serial-number BATCH 10
Data-code COD 3 (YWW)
Plant-code PTC 2
Quantity QTY 8
Accepted by ACC -
Packed by PCK -
Mixed code indicator MIXED CODE -
Origin xxxxxxx+ Company logo
LONG BAR CODE TOP TYPE LENGTH
Item-number N 8
Plant-code N 2
Sequence-number X 3
Quantity N 8
Total length - 21
SHORT BAR CODE BOTTOM TYPE LENGTH
Selection-code X 3
Data-code N 3
Batch-number X 10
Filter - 1
Total length - 17
Aluminum bag
Label
Reel
15973
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative
humidity (RH)
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or
2b. Stored at < 5 % RH
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or
2a. or 2b. are not met.
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or
24 hours at 125 °C ± 5 °C not suitable for reels or tubes
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard JSTD-020
4
LEVEL
22522
Not for New Design
TSOP361..
www.vishay.com Vishay Semiconductors
Rev. 1.9, 21-Feb-12 11 Document Number: 82191
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.