Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Continuous data transmission possible 1 2 3 4 * TTL and CMOS compatibility * Output active low 16797 * Supply voltage: 2.7 V to 5.5 V * Compliant to RoHS Directive 2011/65/EU and in accordance to WEEE 2002/96/EC MECHANICAL DATA Pinning 1 = GND, 2 = GND, 3 = VS, 4 = OUT SPECIAL FEATURES * Enhanced data rate up to 4000 bit/s DESCRIPTION * Operation with short burst possible ( 6 cycles/burst) The TSOP361.. series are miniaturized SMD-IR receiver modules for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. * Taping available for topview and sideview assembly The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the operation with short burst transmission codes and high data rates at a supply voltage of 3 V. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES (AGC1) 36 kHz TSOP36136 38 kHz TSOP36138 40 kHz TSOP36140 56 kHz TSOP36156 BLOCK DIAGRAM APPLICATION CIRCUIT 17170 30 k Transmitter with TSALxxxx VS 4 Input AGC Band pass Demo dulator OUT R 1 = 100 TSOPxxxx VS Circuit 3 C OUT GND + VS C1 = 4.7 F VO GND 1; 2 PIN Control circuit R1 and C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously at a voltage below VO = 2.0 V by the external circuit. GND 16839 Rev. 1.9, 21-Feb-12 1 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION Supply voltage (pin 3) SYMBOL VALUE UNIT VS - 0.3 to + 6 V mA Supply current (pin 3) IS 3 Output voltage (pin 4) VO - 0.3 to (VS + 0.3) V Output current (pin 4) IO 10 mA C Tj 100 Storage temperature range Junction temperature Tstg - 40 to + 100 C Operating temperature range Tamb - 25 to + 85 C Ptot 30 mW Tamb 85 C Power consumption ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION Supply current SYMBOL MIN. Ev = 0 ISD 0.7 Ev = 40 klx, sunlight ISH Supply voltage d Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance (30 kHz to 40 kHz) VS = 3 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. Minimum irradiance (56 kHz) VS = 3 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Minimum irradiance (30 kHz to 40 kHz) Transmission distance MAX. 1.2 1.5 1.3 VS Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA TYP. 2.7 UNIT mA mA 5.5 V 35 m 250 mV 0.35 0.5 W/m2 Ee min. 0.4 0.6 W/m2 VS = 5 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.45 0.6 W/m2 Minimum irradiance (56 kHz) VS = 5 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee min. 0.5 0.7 W/m2 Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee max. Angle of half transmission distance 1/2 Directivity W/m2 30 45 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) 0.35 t po - Output Pulse Width (ms) Ee t tpi *) T *) tpi 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH VOL 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 td 1) tpo 2) 0.30 Output Pulse 0.25 0.20 0.15 16907 Fig. 1 - Output Function Rev. 1.9, 21-Feb-12 = 950 nm, optical test signal, fig.1 0.05 0.00 0.1 t Input Burst Duration 0.10 1 10 100 1000 10 000 Ee - Irradiance (mW/m) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors Optical Test Signal 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO 4.0 Ee min. - Threshold Irradiance (mW/m2) Ee VOH Correlation with ambient light sources: 10 W/m2 1.4 klx (Std.illum.A, T= 2855 K) 10 W/m2 8.2 klx (Daylight, T = 5900 K) 3.5 3.0 2.5 2.0 1.5 Ambient, 0.5 0.0 0.01 VOL t t off t on Ton 0.7 0.6 0.5 Toff 0.3 = 950 nm, optical test signal, fig. 3 0.1 0.0 0.1 1 10 100 1000 0.6 0.4 f = f0 5 % f (3 dB) = f0/7 0.0 16926 f = 100 Hz 0.0 1 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) 2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 1.3 0.0 f/f0 - Relative Frequency 94 8147 Fig. 5 - Frequency Dependence of Responsivity Rev. 1.9, 21-Feb-12 f = 1 kHz 0.5 Ee min. - Threshold Irradiance (mW/m) Ee min./Ee - Rel. Responsivity 0.8 1.1 1.0 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.0 0.9 f = 10 kHz 0.1 1.2 0.7 f = fo 16912 Fig. 4 - Output Pulse Diagram 0.2 100 1.5 10 000 E e - Irradiance (mW/m2) 16910 10 2.0 Ee min. - Threshold Irradiance (mW/m) Ton ,Toff - Output Pulse Width (ms) 0.9 0.2 1 Fig. 6 - Sensitivity in Bright Ambient 1.0 0.4 0.1 E - Ambient DC Irradiance (W/m 2) 16911 Fig. 3 - Output Function 0.8 = 950 nm 1.0 0.4 0.8 1.2 1.6 2.0 E - Field Strength of Disturbance (kV/m) Fig. 8 - Sensitivity vs. Electric Field Disturbances 3 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors 0 1.0 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 0.6 1.0 0.5 0.9 50 0.8 60 0.4 0.3 f = 38 kHz, E e = 2 mW/m 2 0.2 70 0.7 0.1 80 0.0 0 20 40 60 80 100 120 0.6 Burst Length (number of cycles/burst) 16914 0.4 Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length 0 0.2 0.6 0.4 Fig. 12 - Directivity 0.6 Ee min. - Threshold Irradiance (mW/m) 0.2 d rel - Relative Transmission Distance 16801 1.0 0.9 Sensitivity in dark ambient Ee min. - Sensitivity (mW/m 2 ) 0.5 0.4 0.3 0.2 0.1 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 2.0 0.0 - 30 - 15 0 15 30 45 60 75 90 Tamb - Ambient Temperature (C) 16918 17185 Fig. 10 - Sensitivity vs. Ambient Temperature 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage S ( ) rel - Relative Spectral Sensitivity 1.2 1.0 0.8 0.6 0.4 0.2 0.0 750 16919 850 950 1050 1150 - Wavelength (nm) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength Rev. 1.9, 21-Feb-12 4 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The circuit of the TSOP361.. is designed so that unexpected output pulses due to noise or disturbance signals are avoided. A bandpass filter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: * Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz) * Burst length should be 6 cycles/burst or longer 0 16920 * After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is necessary 5 10 15 20 Time (ms) Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation * For each burst which is longer than 1.8 ms a corresponding gap time is necessary at some time in the data stream. This gap time should be as long as the burst or longer * Up to 2200 short bursts per second can be received continuously Some examples for suitable data format are: NEC code, Toshiba Micom Format, Sharp code, RC5 code, RC6 code, RCMM code, R-2000 code, RECS-80 code. When a disturbance signal is applied to the TSOP361.. it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occur. Some examples for such disturbance signals which are suppressed by the TSOP361.. are: * DC light (e.g. from tungsten bulb or sunlight) * Continuous signal at 38 kHz or at any other frequency * Signals from fluorescent lamps with electronic ballast (see figure 14) Rev. 1.9, 21-Feb-12 5 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 7.5 Pick and place area. TT taping 7.2 (1.5) 2.8 2.2 5.3 A 1 4 0.5 0.15 0.1 (1.4) 0.3 4x 0.1 1.27 2.9 3 x 1.27 = 3.81 4 0.4 A 5.51 Not indicated tolerances 0.3 Pick and place area. TR taping technical drawings according to DIN specifications 2.6 Footprint 2.35 3 x 1.27 = 3.81 0.9 2.2 1.27 R 1.7 Drawing-No.: 6.544-5341.01-4 Issue: 8; 02.09.09 16776 ASSEMBLY INSTRUCTIONS Reflow Soldering * Handling after reflow should be done only after the work surface has been cooled off * Reflow soldering must be done within 72 h while stored under a max. temperature of 30 C, 60 % RH after opening the dry pack envelope Manual Soldering * Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 C * Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Excercise extreme care to keep the maximum temperature below 260 C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured Rev. 1.9, 21-Feb-12 * Finish soldering within 3 s * Handle products only after the temperature has cooled off 6 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 C 245 C 255 C 240 C 217 C 250 T (C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 C/s max. Ramp Down 6 C/s 50 0 0 19800 50 100 150 t (s) 200 250 300 max. 2 cycles allowed TAPING VERSION TSOP..TT DIMENSIONS in millimeters 16584 Rev. 1.9, 21-Feb-12 7 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR DIMENSIONS in millimeters 16585 Rev. 1.9, 21-Feb-12 8 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. (300 10) mm/min. 165 to 180 peel angle Rev. 1.9, 21-Feb-12 9 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 Item-number INO 8 Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - LOT-/serial-number Mixed code indicator Origin LONG BAR CODE TOP MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 SHORT BAR CODE BOTTOM TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 DRY PACKING After more than 72 h under these conditions moisture content will be too high for reflow soldering. The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 C + 5 C/- 0 C and < 5 % RH (dry air/nitrogen) Aluminum bag or 96 h at 60 C + 5 C and < 5 % RH for all device containers Label or 24 h at 125 C + 5 C not suitable for reel or tubes. An EIA JEDEC standard JSTD-020 level 4 label is included on all dry bags. Reel LEVEL CAUTION 15973 This bag contains MOISTURE-SENSITIVE DEVICES FINAL PACKING 4 1. Shelf life in sealed bag: 12 months at < 40 C and < 90 % relative humidity (RH) The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 C) must be 2a. Mounted within 72 hours at factory condition of < 30 C/60 % RH or 2b. Stored at < 5 % RH RECOMMENDED METHOD OF STORAGE 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 C 5 C or 2a. or 2b. are not met. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: 4. If baking is required, devices may be baked for: 192 hours at 40 C + 5 C/- 0 C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 C 5 C and < 5 % RH for all device containers or 24 hours at 125 C 5 C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) Note: Level and body temperature defined by EIA JEDEC Standard JSTD-020 * Storage temperature 10 C to 30 C 22522 * Storage humidity 60 % RH max. Rev. 1.9, 21-Feb-12 EIA JEDEC standard JSTD-020 level 4 label is included on all dry bags 10 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP361.. www.vishay.com Vishay Semiconductors ESD PRECAUTION VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electro-static sensitive devices warning labels are on the packaging. The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 16962 Rev. 1.9, 21-Feb-12 11 Document Number: 82191 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000